Abstract: A 15-storey RC building, studied in this paper, is
representative of modern building type constructed in Madina City in
Saudi Arabia before 10 years ago. These buildings are almost
consisting of reinforced concrete skeleton i.e. columns, beams and
flat slab as well as shear walls in the stairs and elevator areas
arranged in the way to have a resistance system for lateral loads
(wind – earthquake loads). In this study, the dynamic properties of
the 15-storey RC building were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Three dimensional pushover analysis (Nonlinear static
analysis) was carried out using SAP2000 software incorporating
inelastic material properties for concrete, infill and steel. The effect
of modeling the building with and without infill walls, on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madina area has been investigated. ATC-
40 capacity and demand spectra are utilized to get the modification
factor (R) for the studied building. The purpose of this analysis is to
evaluate the expected performance of structural systems by
estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results are summarized and discussed.
Abstract: With the increasing number of people reviewing
products online in recent years, opinion sharing websites has become
the most important source of customers’ opinions. Unfortunately,
spammers generate and post fake reviews in order to promote or
demote brands and mislead potential customers. These are notably
destructive not only for potential customers, but also for business
holders and manufacturers. However, research in this area is not
adequate, and many critical problems related to spam detection have
not been solved to date. To provide green researchers in the domain
with a great aid, in this paper, we have attempted to create a highquality
framework to make a clear vision on review spam-detection
methods. In addition, this report contains a comprehensive collection
of detection metrics used in proposed spam-detection approaches.
These metrics are extremely applicable for developing novel
detection methods.
Abstract: In this current contribution, authors are dedicated to
investigate influence of the crystal lamellae orientation on
electromechanical behaviors of relaxor ferroelectric Poly
(vinylidene fluoride –trifluoroethylene -chlorotrifluoroethylene)
(P(VDF-TrFE-CTFE)) films by control of polymer microstructure,
aiming to picture the full map of structure-property relationship. In
order to define their crystal orientation films, terpolymer films were
fabricated by solution-casting, stretching and hot-pressing process.
Differential scanning calorimetry, impedance analyzer, and tensile
strength techniques were employed to characterize crystallographic
parameters, dielectric permittivity, and elastic Young’s modulus
respectively. In addition, large electrical induced out-of-plane
electrostrictive strain was obtained by cantilever beam mode.
Consequently, as-casted pristine films exhibited surprisingly high
electrostrictive strain 0.1774% due to considerably small value of
elastic Young’s modulus although relatively low dielectric
permittivity. Such reasons contributed to large mechanical elastic
energy density. Instead, due to 2 folds increase of elastic Young’s
modulus and less than 50% augmentation of dielectric constant, fullycrystallized
film showed weak electrostrictive behavior and
mechanical energy density as well. And subjected to mechanical
stretching process, Film C exhibited stronger dielectric constant and
out-performed electrostrictive strain over Film B because edge-on
crystal lamellae orientation induced by uniaxially mechanical stretch.
Hot-press films were compared in term of cooling rate. Rather large
electrostrictive strain of 0.2788% for hot-pressed Film D in
quenching process was observed although its dielectric permittivity
equivalent to that of pristine as-casted Film A, showing highest
mechanical elastic energy density value of 359.5 J/m3. In hot-press
cooling process, dielectric permittivity of Film E saw values at 48.8
concomitant with ca.100% increase of Young’s modulus. Films with
intermediate mechanical energy density were obtained.
Abstract: Energy has a prominent role for development of
nations. Countries which have energy resources also have strategic
power in the international trade of energy since it is essential for all
stages of production in the economy. Thus, it is important for
countries to analyze the weaknesses and strength of the system. On
the other side, international trade is one of the fields that are analyzed
as a complex network via network analysis. Complex network is one
of the tools to analyze complex systems with heterogeneous agents
and interaction between them. A complex network consists of nodes
and the interactions between these nodes. Total properties which
emerge as a result of these interactions are distinct from the sum of
small parts (more or less) in complex systems. Thus, standard
approaches to international trade are superficial to analyze these
systems. Network analysis provides a new approach to analyze
international trade as a network. In this network, countries constitute
nodes and trade relations (export or import) constitute edges. It
becomes possible to analyze international trade network in terms of
high degree indicators which are specific to complex networks such
as connectivity, clustering, assortativity/disassortativity, centrality,
etc. In this analysis, international trade of crude oil and coal which
are types of fossil fuel has been analyzed from 2005 to 2014 via
network analysis. First, it has been analyzed in terms of some
topological parameters such as density, transitivity, clustering etc.
Afterwards, fitness to Pareto distribution has been analyzed via
Kolmogorov-Smirnov test. Finally, weighted HITS algorithm has
been applied to the data as a centrality measure to determine the real
prominence of countries in these trade networks. Weighted HITS
algorithm is a strong tool to analyze the network by ranking countries
with regards to prominence of their trade partners. We have
calculated both an export centrality and an import centrality by
applying w-HITS algorithm to the data. As a result, impacts of the
trading countries have been presented in terms of high-degree
indicators.
Abstract: Nanofibers are defined as fibers with diameters less
than 100 nanometers. In this study, behaviours of activated carbon
nanofiber (ACNF), carbon nanofiber (CNF), polyacrylonitrile/ carbon
nanotube (PAN/CNT), polyvinyl alcohol/nanosilver (PVA/Ag) in
proton exchange membrane (PEM) fuel cells are investigated
experimentally. This material was used as gas diffusion layer (GDL)
in PEM fuel cells. In this study, the electrical conductivities of
nanofiber and nanofiber/nanoparticles have been studied to
understand their effects on PEM fuel cell performance. According to
the experimental results, the maximum electrical conductivity
performance of the fuel cell with nanofiber was found to be at
PVA/Ag (at UConn condition). The electrical conductivities of CNF,
ACNF, PAN/CNT are lower for PEM. The resistance of cell with
PVA/Ag is lower than the resistance of cell with PAN/CNT, ACNF,
CNF.
Abstract: The study of the aerodynamics related to the
improvement in the acting of airplanes and automobiles with the
objective of being reduced the effect of the attrition of the air on
structures, providing larger speeds and smaller consumption of fuel.
The application of the knowledge of the aerodynamics not more
limits to the aeronautical and automobile industries. Therefore, this
research aims to design and construction of a wind tunnel to perform
aerodynamic analysis in bodies of cars, seeking greater efficiency.
Therefore, this research aims to design and construction of a wind
tunnel to perform aerodynamic analysis in bodies of cars, seeking
greater efficiency. For this, a methodology for wind tunnel type
selection is designed to be built, taking into account the various
existing configurations in which chose to build an open circuit tunnel,
due to the lower complexity of construction and installation;
operational simplicity and low cost. The guidelines for the project
were teaching: the layer that limits study and analyze specimens with
different geometries. For the variation of pressure in the test, section
of a switched gauge used a pitot tube. Thus, it was possible to obtain
quantitative and qualitative results, which proved to be satisfactory.
Abstract: Scripts are one of the basic text resources to understand
broadcasting contents. Topic modeling is the method to get the
summary of the broadcasting contents from its scripts. Generally,
scripts represent contents descriptively with directions and speeches,
and provide scene segments that can be seen as semantic units.
Therefore, a script can be topic modeled by treating a scene segment
as a document. Because scene segments consist of speeches mainly,
however, relatively small co-occurrences among words in the scene
segments are observed. This causes inevitably the bad quality of
topics by statistical learning method. To tackle this problem, we
propose a method to improve topic quality with additional word
co-occurrence information obtained using scene similarities. The
main idea of improving topic quality is that the information that
two or more texts are topically related can be useful to learn high
quality of topics. In addition, more accurate topical representations
lead to get information more accurate whether two texts are related
or not. In this paper, we regard two scene segments are related
if their topical similarity is high enough. We also consider that
words are co-occurred if they are in topically related scene segments
together. By iteratively inferring topics and determining semantically
neighborhood scene segments, we draw a topic space represents
broadcasting contents well. In the experiments, we showed the
proposed method generates a higher quality of topics from Korean
drama scripts than the baselines.
Abstract: Energy consumption of a hotel can be a hot topic in
smart city; it is difficult to evaluate the contribution of impact factors
to energy consumption of a hotel. Therefore, grasping the key impact
factors has great effect on the energy saving management of a hotel.
Based on the SPIRTPAT model, we establish the identity with the
impact factors of occupancy rate, unit area of revenue, temperature
factor, unit revenue of energy consumption. In this paper, we use the
LMDI (Logarithmic Mean Divisia Index) to decompose the impact
factors of energy consumption of hotel from Jan. to Dec. in 2001. The
results indicate that the occupancy rate and unit area of revenue are the
main factors that can increase unit area of energy consumption, and the
unit revenue of energy consumption is the main factor to restrain the
growth of unit area of energy consumption. When the energy
consumption of hotel can appear abnormal, the hotel manager can
carry out energy saving management and control according to the
contribution value of impact factors.
Abstract: Weak damping of low frequency oscillations is a frequent phenomenon in electrical power systems. These frequencies can be damped by power system stabilizers. Unified power flow controller (UPFC), as one of the most important FACTS devices, can be applied to increase the damping of power system oscillations and the more effect of this controller on increasing the damping of oscillations depends on its proper placement in power systems. In this paper, a technique based on controllability is proposed to select proper location of UPFC and the best input control signal in order to enhance damping of power oscillations. The effectiveness of the proposed technique is demonstrated in IEEE 9 bus power system.
Abstract: There was a scenario present day that drying of fresh
fruits and vegetables by indirect solar drying by using mechanical
device; hence, an effort was made to develop a small scale solar
tunnel dryer (STD). Drying of spinach is carried out to analyze the
performance of the dryer and to study its drying characteristics. To
evaluate the performance of dryer the independent variables were
selected as air flow rate, loading density and shade net while collector
efficiency, drying efficiency, overall efficiency and specific energy
consumption were selected as responses during performing the
experiments. The spinach was dried from initial moisture content
88.21-94.04% (w.b.) to final moisture content 3.50-5.13% (w.b.). The
drying time considerably reduced as compared to open sun drying of
spinach as sun drying took 15 h for drying. The average collector
efficiency, drying efficiency and overall efficiency were in the range
28.73-61.15%, 11.63% to 22.13%, and 7.61-14.66%, respectively.
Abstract: This paper investigates the characteristics of wall
pressure fluctuations in naturally developing boundary layer flows
on axisymmetric bodies experimentally. The axisymmetric body has
a modified ellipsoidal blunt nose. Flush-mounted microphones are
used to measure the wall pressure fluctuations in the boundary layer
flow over the body. The measurements are performed in a low noise
wind tunnel. It is found that the correlation between the flow regime
and the characteristics of the pressure fluctuations is distinct. The
process from small fluctuation in laminar flow to large fluctuation in
turbulent flow is investigated. Tollmien-Schlichting wave (T-S wave)
is found to generate and develop in transition. Because of the T-S
wave, the wall pressure fluctuations in the transition region are higher
than those in the turbulent boundary layer.
Abstract: Test automation allows performing difficult and time
consuming manual software testing tasks efficiently, quickly and
repeatedly. However, development and maintenance of automated
tests is expensive, so it needs a proper prioritization what to automate
first. This paper describes a simple yet efficient approach for such
prioritization of test cases based on the effort needed for both manual
execution and software test automation. The suggested approach is
very flexible because it allows working with a variety of assessment
methods, and adding or removing new candidates at any time. The
theoretical ideas presented in this article have been successfully
applied in real world situations in several software companies by the
authors and their colleagues including testing of real estate websites,
cryptographic and authentication solutions, OSGi-based middleware
framework that has been applied in various systems for smart homes,
connected cars, production plants, sensors, home appliances, car head
units and engine control units (ECU), vending machines, medical
devices, industry equipment and other devices that either contain or
are connected to an embedded service gateway.
Abstract: Cochlear Implantation (CI) which became a routine
procedure for the last decades is an electronic device that provides a
sense of sound for patients who are severely and profoundly deaf.
The optimal success of this implantation depends on the electrode
technology and deep insertion techniques. However, this manual
insertion procedure may cause mechanical trauma which can lead to
severe destruction of the delicate intracochlear structure.
Accordingly, future improvement of the cochlear electrode implant
insertion needs reduction of the excessive force application during
the cochlear implantation which causes tissue damage and trauma.
This study is examined tool-tissue interaction of large prototype scale
digit embedded with distributive tactile sensor based upon cochlear
electrode and large prototype scale cochlea phantom for simulating
the human cochlear which could lead to small scale digit
requirements. The digit, distributive tactile sensors embedded with
silicon-substrate was inserted into the cochlea phantom to measure
any digit/phantom interaction and position of the digit in order to
minimize tissue and trauma damage during the electrode cochlear
insertion. The digit have provided tactile information from the digitphantom
insertion interaction such as contact status, tip penetration,
obstacles, relative shape and location, contact orientation and
multiple contacts. The tests demonstrated that even devices of such a
relative simple design with low cost have potential to improve
cochlear implant surgery and other lumen mapping applications by
providing tactile sensory feedback information and thus controlling
the insertion through sensing and control of the tip of the implant
during the insertion. In that approach, the surgeon could minimize the
tissue damage and potential damage to the delicate structures within
the cochlear caused by current manual electrode insertion of the
cochlear implantation. This approach also can be applied to other
minimally invasive surgery applications as well as diagnosis and path
navigation procedures.
Abstract: The occurrences of precipitation, also commonly
referred as rain, in the form of "convective" and "stratiform" have
been identified to exist worldwide. In this study, the radar return
echoes or known as reflectivity values acquired from radar scans
have been exploited in the process of classifying the type of rain
endured. The investigation use radar data from Malaysian
Meteorology Department (MMD). It is possible to discriminate the
types of rain experienced in tropical region by observing the vertical
characteristics of the rain structure. .Heavy rain in tropical region
profoundly affects radiowave signals, causing transmission
interference and signal fading. Required wireless system fade margin
depends on the type of rain. Information relating to the two
mentioned types of rain is critical for the system engineers and
researchers in their endeavour to improve the reliability of
communication links. This paper highlights the quantification of
percentage occurrences over one year period in 2009.
Abstract: This experimental study consists of a characterization
of epoxy grout where an amount of 2% of graphene nanoplatelets
particles were added to commercial epoxy resin to evaluate their
behavior regarding neat epoxy resin. Compressive tests, tensile tests
and flexural tests were conducted to study the effect of graphene
nanoplatelets on neat epoxy resin. By comparing graphene-based and
neat epoxy grout, there is no significant increase of strength due to
weak interface in the graphene nanoplatelets/epoxy composites.
From this experiment, the tension and flexural strength of graphenebased
epoxy grouts is slightly lower than ones of neat epoxy grout.
Nevertheless, the addition of graphene has produced more consistent
results according to a smaller standard deviation of strength.
Furthermore, the graphene has also improved the ductility of the
grout, hence reducing its brittle behaviour. This shows that the
performance of graphene-based grout is reliably predictable and able
to minimise sudden rupture. This is important since repair design of
damaged pipeline is of deterministic nature.
Abstract: Rapid developments in technology in the present age
have made it necessary for communities to follow technological
developments and adapt themselves to these developments. One of
the fields that are most rapidly affected by these developments is
undoubtedly education. Determination of the attitudes of preservice
teachers, who live in an age of technology and get ready to raise
future individuals, is of paramount importance both educationally and
professionally. The purpose of this study was to analyze attitudes of
preservice teachers towards technology and some variables that
predict these attitudes (gender, daily duration of internet use, and the
number of technical devices owned). 329 preservice teachers
attending the education faculty of a large university in central Turkey
participated, on a volunteer basis, in this study, where relational
survey model was used as the research method. Research findings
reveal that preservice teachers’ attitudes towards technology are
positive and at the same time, the attitudes of male preservice
teachers towards technology are more positive than their female
counterparts. As a result of the stepwise multiple regression analysis
where factors predicting preservice teachers’ attitudes towards
technology, it was found that duration of daily internet use was the
strongest predictor of attitudes towards technology.
Abstract: Context-aware technologies provide system
applications with the awareness of environmental conditions,
customer behaviours, object movements, etc. Further, with such
capability system applications can be smart to intelligently adapt their
responses to the changing conditions. In regard to business
operations, this promises businesses that their business processes can
run more intelligently, adaptively and flexibly, and thereby either
improve customer experience, enhance reliability of service delivery,
or lower operational cost, to make the business more competitive and
sustainable. Aiming at realising such context-aware business process
management, this paper firstly explores its potential benefit, and then
identifies some gaps between the current business process
management support and the expected. In addition, some preliminary
solutions are also discussed in regard to context definition, rule-based
process execution, run-time process evolution, etc. A framework is
also presented to give a conceptual architecture of context-aware
business process management system to guide system
implementation.
Abstract: Sewage sludge is a biomass resource that can create a
solid fuel and electricity. Utilizing sewage sludge as a renewable
energy can contribute to the reduction of greenhouse gases. In Japan,
the "National Plan for the Promotion of Biomass Utilization" and the
“Priority Plan for Social Infrastructure Development" were approved
at cabinet meetings in December 2010 and August 2012, respectively,
to promote the energy utilization of sewage sludge. This study
investigated costs and greenhouse gas emission in different sewage
sludge treatments with technologies for energy from sewage sludge.
Expenses were estimated based on capital costs and O&M costs
including energy consumption of solid fuel plants and biogas power
generation plants for sewage sludge. Results showed that the cost of
sludge digestion treatment with solid fuel technologies was 8% lower
than landfill disposal. The greenhouse gas emission of sludge
digestion treatment with solid fuel technologies was also 6,390t as
CO2 smaller than landfill disposal. Biogas power generation reduced
the electricity of a wastewater treatment plant by 30% and the cost by
5%.
Abstract: Small-size and low-power sensors with sensing, signal
processing and wireless communication capabilities is suitable for the
wireless sensor networks. Due to the limited resources and battery
constraints, complex routing algorithms used for the ad-hoc networks
cannot be employed in sensor networks. In this paper, we propose
node-disjoint multi-path hexagon-based routing algorithms in wireless
sensor networks. We suggest the details of the algorithm and compare
it with other works. Simulation results show that the proposed scheme
achieves better performance in terms of efficiency and message
delivery ratio.
Abstract: Online measurement of the product quality is a
challenging task in cement production, especially in the production of
Celitement, a novel environmentally friendly hydraulic binder. The
mineralogy and chemical composition of clinker in ordinary Portland
cement production is measured by X-ray diffraction (XRD) and
X-ray fluorescence (XRF), where only crystalline constituents can be
detected. But only a small part of the Celitement components can be
measured via XRD, because most constituents have an amorphous
structure. This paper describes the development of algorithms
suitable for an on-line monitoring of the final processing step of
Celitement based on NIR-data. For calibration intermediate products
were dried at different temperatures and ground for variable
durations. The products were analyzed using XRD and
thermogravimetric analyses together with NIR-spectroscopy to
investigate the dependency between the drying and the milling
processes on one and the NIR-signal on the other side. As a result,
different characteristic parameters have been defined. A short
overview of the Celitement process and the challenging tasks of the
online measurement and evaluation of the product quality will be
presented. Subsequently, methods for systematic development of
near-infrared calibration models and the determination of the final
calibration model will be introduced. The application of the model on
experimental data illustrates that NIR-spectroscopy allows for a quick
and sufficiently exact determination of crucial process parameters.