Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: Driver fatigue is an important factor in the increasing
number of road accidents. Dynamic template matching method was
proposed to address the problem of real-time driver fatigue detection
system based on eye-tracking. An effective vision based approach
was used to analyze the driver’s eye state to detect fatigue. The driver
fatigue system consists of Face detection, Eye detection, Eye
tracking, and Fatigue detection. Initially frames are captured from a
color video in a car dashboard and transformed from RGB into YCbCr
color space to detect the driver’s face. Canny edge operator was used
to estimating the eye region and the locations of eyes are extracted.
The extracted eyes were considered as a template matching for eye
tracking. Edge Map Overlapping (EMO) and Edge Pixel Count
(EPC) matching function were used for eye tracking which is used to
improve the matching accuracy. The pixel of eyeball was tracked
from the eye regions which are used to determine the fatigue state of
the driver.
Abstract: Pneumatic reactors have been widely employed in various sectors of the chemical industry, especially where are required high heat and mass transfer rates. This study aimed to obtain correlations that allow the prediction of gas hold-up (Ԑ) and volumetric oxygen transfer coefficient (kLa), and compare these values, for three models of pneumatic reactors on two scales utilizing Newtonian fluids. Values of kLa were obtained using the dynamic pressure-step method, while e was used for a new proposed measure. Comparing the three models of reactors studied, it was observed that the mass transfer was superior to draft-tube airlift, reaching e of 0.173 and kLa of 0.00904s-1. All correlations showed good fit to the experimental data (R2≥94%), and comparisons with correlations from the literature demonstrate the need for further similar studies due to shortage of data available, mainly for airlift reactors and high viscosity fluids.
Abstract: Potassium borates, which are widely used in welding
and metal refining industry, as a lubricating oil additive, cement
additive, fiberglass additive and insulation compound, are one of the
important groups of borate minerals. In this study the production of a
potassium borate mineral via hydrothermal method is aimed. The
potassium source of potassium nitrate (KNO3) was used along with a
sodium source of sodium hydroxide (NaOH) and boron source of
boric acid (H3BO3). The constant parameters of reaction temperature
and reaction time were determined as 80°C and 1 h, respectively. The
molar ratios of 1:1:3 (as KNO3:NaOH:H3BO3), 1:1:4, 1:1:5, 1:1:6
and 1:1:7 were used. Following the synthesis the identifications of
the produced products were conducted by X-Ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FT-IR) and Raman
Spectroscopy. The results of the experiments and analysis showed in
the ratio of 1:1:6, the Santite mineral with powder diffraction file
number (pdf no.) of 01-072-1688, which is known as potassium
pentaborate (KB5O8·4H2O) was synthesized as best.
Abstract: This paper presents the results of an experimental
study undertaken to evaluate the local bond stress-slip response of
short embedment of reinforcing bars in normal concrete (NC) and
high performance fiber reinforced cement composites (HPFRCC)
blocks. Long embedment was investigated as well to gain insights on
the distribution of strain, slip, bar stress and bond stress along the bar
especially in post-yield range. A total of 12 specimens were tested,
by means of pull-out of the reinforcing bars from concrete blocks. It
was found that the enhancement of local bond strength can be
reached up to 50% and ductility of the bond behavior was improved
significantly if HPFRCC is used. Also, under a constant strain at
loaded end, HPFRCC has delayed yielding of bars at other location
from the loaded end. Hence, the reduction of bond stress was slower
for HPFRCC in comparison with NC. Due to the same reason, the
total slips at loaded end for HPFRCC was smaller than NC as
expected. Test results indicated that HPFRCC has better bond slip
behavior which makes it a suitable material to be employed in
anchorage zone such as beam-column joints.
Abstract: The effect of partially substitution of magnetic
impurity Fe for Cu to the magnetic and transport properties in
electron-doped superconducting cuprates of
Eu1.85+yCe0.15-yCu1-yFeyO4+α-δ (ECCFO) with y = 0, 0.010, 0.020, and
0.050 has been studied, in order to investigate the mechanism of
magnetic and transport properties of ECCFO in normal-state.
Magnetic properties are investigated by DC magnetic-susceptibility
measurements that carried out at low temperatures down to 2 K using a
standard SQUID magnetometer in a magnetic field of 5 Oe on field
cooling. Transport properties addressed to electron mobility, are
extracted from radius of electron localization calculated from
temperature dependence of resistivity. For y = 0, temperature
dependence of dc magnetic-susceptibility (χ) indicated the change of
magnetic behavior from paramagnetic to diamagnetic below 15 K.
Above 15 K, all samples show paramagnetic behavior with the values
of magnetic moment in every volume unit increased with increasing y.
Electron mobility decreased with increasing y.
Abstract: This paper presents a method of evaluating the effect
of aggregate angularity on hot mix asphalt (HMA) properties and its
relationship to the Permanent Deformation resistance. The research
concluded that aggregate particle angularity had a significant effect
on the Permanent Deformation performance, and also that with an
increase in coarse aggregate angularity there was an increase in the
resistance of mixes to Permanent Deformation. A comparison
between the measured data and predictive data of permanent
deformation predictive models showed the limits of existing
prediction models. The numerical analysis described the permanent
deformation zones and concluded that angularity has an effect of the
onset of these zones. Prediction of permanent deformation help road
agencies and by extension economists and engineers determine the
best approach for maintenance, rehabilitation, and new construction
works of the road infrastructure.
Abstract: Some plants of genus Schinus have been used in the
folk medicine as topical antiseptic, digestive, purgative, diuretic,
analgesic or antidepressant, and also for respiratory and urinary
infections. Chemical composition of essential oils of S. molle and S.
terebinthifolius had been evaluated and presented high variability
according with the part of the plant studied and with the geographic
and climatic regions. The pharmacological properties, namely
antimicrobial, anti-tumoural and anti-inflammatory activities are
conditioned by chemical composition of essential oils. Taking into
account the difficulty to infer the pharmacological properties of
Schinus essential oils without hard experimental approach, this work
will focus on the development of a decision support system, in terms
of its knowledge representation and reasoning procedures, under a
formal framework based on Logic Programming, complemented with
an approach to computing centered on Artificial Neural Networks
and the respective Degree-of-Confidence that one has on such an
occurrence.
Abstract: Optical biosensors have become a powerful detection
and analysis tool for wide-ranging applications in biomedical research,
pharmaceuticals and environmental monitoring. This study carried out
the computational fluid dynamics (CFD)-based simulations to explore
the dispersion phenomenon in the micro channel of an optical
biosensor. The predicted time sequences of concentration contours
were utilized to better understand the dispersion development occurred
in different geometric shapes of micro channels. The simulation results
showed the surface concentrations at the sensing probe (with the best
performance of a grating coupler) in respect of time to appraise the
dispersion effect and therefore identify the design configurations
resulting in minimum dispersion.
Abstract: The objective of this study is to conduct computational
fluid dynamic (CFD) simulations for evaluating the cooling efficacy
from vegetation implanted in a public park in the Taipei, Taiwan. To
probe the impacts of park renewal by means of adding three pavilions
and supplementary green areas on urban microclimates, the simulated
results have revealed that the park having a higher percentage of green
coverage ratio (GCR) tended to experience a better cooling effect.
These findings can be used to explore the effects of different greening
modifications on urban environments for achieving an effective
thermal comfort in urban public spaces.
Abstract: In a practical power system, the power plants are not
located at the same distance from the center of loads and their fuel
costs are different. Also, under normal operating conditions, the
generation capacity is more than the total load demand and losses.
Thus, there are many options for scheduling generation. In an
interconnected power system, the objective is to find the real and
reactive power scheduling of each power plant in such a way as to
minimize the operating cost. This means that the generator’s real and
reactive powers are allowed to vary within certain limits so as to meet
a particular load demand with minimum fuel cost. This is called
optimal power flow problem. In this paper, Economic Load Dispatch
(ELD) of real power generation is considered. Economic Load
Dispatch (ELD) is the scheduling of generators to minimize total
operating cost of generator units subjected to equality constraint of
power balance within the minimum and maximum operating limits of
the generating units. In this paper, genetic algorithms are considered.
ELD solutions are found by solving the conventional load flow
equations while at the same time minimizing the fuel costs.
Abstract: Any variation in environmental characteristics of
geomorphosites would lead to destabilisation of their geotouristic
values all around the planet. The Urmia lake, with an area of
approximately 5,500 km2 and a catchment area of 51,876 km2, and to
which various reasons over time, especially in the last fifty years
have seen a sharp decline and have decreased by about 93 % in two
recent decades. These variations are not only driving significant
changes in the morphology and ecology of the present lake
landscape, but at the same time are shaping newly formed
morphologies, which vanished some valuable geomorphosites or
develop into smaller geomorphosites with significant value from a
scientific and cultural point of view. This paper analyses and
discusses features and evolution in several representative coastal and
island geomorphosites. For this purpose, a total of 23 geomorphosites
were studied in two data series (1963 and 2015) and the respective
data were compared and analysed. The results showed, the total loss
in geomorphosites area in a half century amounted to a loss of more
than 90% of the valuable geomorphosites. Moreover, the comparison
between the mean yearly value of coastal area lost over the entire
period and the yearly average calculated for the shorter period (1998-
2014) clearly indicates a pattern of acceleration. This acceleration in
the rate of reduction in lake area was seen in most of the southern
half of the lake. In the region as well, the general water-level falling
is not only causing the loss of a significant water resource, which is
followed by major impact on regional ecosystems, but is also driving
the most marked recent (last century) changes in the geotouristic
landscapes. In fact, the disappearance of geomorphosites means the
loss of tourism phenomenon. In this context attention must be paid to
the question of conservation. The action needed to safeguard
geomorphosites includes: 1) Preventive action, 2) Corrective action,
and 3) Sharing knowledge.
Abstract: In this study, one of the tools of Islamic financing
known as “Sukuk” a non-interest bearing investment which has
started to be implemented in Turkey and the world as a whole is
discussed. In order to increase the vitality and efficiency of the
economy, by taking lessons from the recent economic crisis new
developments in the banking and investment sector are being
expanded. The purpose of all investors is to obtain more revenue
through the use of capital. The inability of traditional investment
tools to meet the expectations of investors and the interest based
financial system where one investor benefits at the expense of
another there has been the need for a different, reliable and noninterest
bearing financial market that is consistent with the Islamic
rule. As a result an alternative and more reliable interest free
financing tool “Sukuk” rental certificates covering people who are
sensitive to Islamic rules, appeal to all segments, hidden remaining
capital that contributes to the economy, reduce disparities in income
distribution, common risk sharing system of profit and loss sharing
has emerged. Today, for the structural countries by examining the
state of the world market economy the applicability, enactment and
future issues associated with this attractive kind of Islamic finance
namely the “Sukuk” market has been explained.
Abstract: The rationale behind this study is considering
combating and preventing the phenomenon of trafficking in human
beings from a multidisciplinary perspective that involves many layers
of the society.
Trafficking in human beings is an abhorrent phenomenon highly
affecting negatively the victims and their families in both human and
material aspect, sometimes causing irreversible damages. The longer
term effects of this phenomenon, in countries with a weak economic
development and extremely young and dynamic population, such as
Kosovo, without proper measures to prevented and control can cause
tremendous damages in the society. Given the fact that a complete
eradication of this phenomenon is almost impossible, efforts should
be concentrated at least on the prevention and controlling aspects.
Treating trafficking in human beings based on traditional police
tactics, methods and proceedings cannot bring satisfactory results.
There is no doubt that a multi-disciplinary approach is an
irreplaceable requirement, in other words, a combination of authentic
and functional proactive and reactive methods, techniques and tactics.
Obviously, police must exercise its role in preventing and combating
trafficking in human beings, a role sanctioned by the law, however,
police role and contribution cannot by any means considered
complete if all segments of the society are not included in these
efforts. Naturally, civil society should have an important share in
these collaborative and interactive efforts especially in preventive
activities such as: awareness on trafficking risks and damages,
proactive engagement in drafting appropriate legislation and
strategies, law enforcement monitoring and direct or indirect
involvement in protective and supporting activities which benefit the
victims of trafficking etc.
Abstract: This paper addresses the design of hospital Intensive
Care Unit windows for the achievement of visual comfort and energy
savings. The aim was to identify the window size and shading system
configurations that could fulfill daylighting adequacy, avoid glare
and reduce energy consumption. The study focused on addressing the
effect of utilizing different shading systems in association with a
range of Window-to-Wall Ratios (WWR) in different orientations
under the desert clear-sky of Cairo, Egypt.
The results of this study demonstrated that solar penetration is a
critical concern affecting the design of ICU windows in desert
locations, as in Cairo, Egypt. Use of shading systems was found to be
essential in providing acceptable daylight performance and energy
saving. Careful positioning of the ICU window towards a proper
orientation can dramatically improve performance. It was observed
that ICU windows facing the north direction enjoyed the widest range
of successful window configuration possibilities at different WWRs.
ICU windows facing south enjoyed a reasonable number of
configuration options as well. By contrast, the ICU windows facing
the east orientation had a very limited number of options that provide
acceptable performance. These require additional local shading
measures at certain times due to glare incidence. Moreover, use of
horizontal sun breakers and solar screens to protect the ICU windows
proved to be more successful than the other alternatives in a wide
range of Window to Wall Ratios. By contrast, the use of light shelves
and vertical shading devices seemed questionable.
Abstract: Electrodeposition is a simple and economic technique
for precision coating of different shaped substrates with pure metal,
alloy or composite films. Dc electrodeposition was used to produce
Cr, Co-Cr and Co-Cr/TiO2 nano-composite coatings from Cr(III)
based electrolytes onto 316L SS substrates. The effects of TiO2 nanoparticles
concentration on co-deposition of these particles along with
Cr content and microhardness of the coatings were investigated.
Morphology of the Cr, Co-Cr and Co-Cr/TiO2 coatings besides their
tribological behavior were studied. The results showed that increment
of TiO2 nanoparticles concentration from 0 to 30 g L-1 in the bath
increased their co-deposition and Cr content of the coatings from 0 to
3.5 wt.% and from 23.7 to 31.2 wt.%, respectively. Microhardness of
Cr coating was about 920 Hv which was higher than Co-Cr and even
Co-Cr/TiO2 films. Microhardness of Co-Cr and Co-Cr/TiO2 coatings
were improved by increasing their Cr and TiO2 content. All the
coatings had nodular morphology and contained microcracks.
Nodules sizes and the number of microcracks in the alloy and
composite coatings were lower than the Cr film. Wear results
revealed that the Co-Cr/TiO2 coating had the lowest wear loss
between all the samples, while the Cr film had the worst wear
resistance.
Abstract: Authenticity in advertising is the cornerstone of
modern marketing. Despite research advances related to the role of
authenticity in marketing, it remains unclear why customers respond to
authentic brand stories. The results show that different personality
traits will moderate the influence of different authenticity on the levels
of emotion. Whether indexically authentic or iconically authentic
advertisements were shown to extroverts, open people and agreeable
people, they will evoke more positive emotions. When neurotic people
and conscientious people see the iconically authentic advertising
rather than the indexically authentic advertising, they will produce
more negative emotions. In addition, the emotion evoked by
advertising had significant positive impact on brand attitude evoked by
advertising had significant negative impact on brand attitude. These
findings provide some managerial implications and directions for
further research.
Abstract: The comprehensive CFD models have been used to
represent and study the heterogeneous combustion of biomass. In the
present work, the operation of a global flue gas circuit in the sugarcane
bagasse combustion, from wind boxes below primary air grate
supply, passing by bagasse insertion in swirl burners and boiler
furnace, to boiler bank outlet is simulated. It uses five different
meshes representing each part of this system located in sequence:
wind boxes and grate, boiler furnace, swirl burners, superheaters and
boiler bank. The model considers turbulence using standard k-ε,
combustion using EDM, radiation heat transfer using DTM with 16
ray directions and bagasse particle tracking represented by Schiller-
Naumann model. The results showed good agreement with expected
behavior found in literature and equipment design. The more detailed
results view in separated parts of flue gas system allows observing
some flow behaviors that cannot be represented by usual
simplifications like bagasse supply under homogeneous axial and
rotational vectors and others that can be represented using new
considerations like the representation of 26 thousand grate orifices by
144 rectangular inlets.
Abstract: This article is to introduce the meaning and form of
social quality moving process as indicated by members of two suburb
communities with different social and cultural contexts. The form of
social quality moving process is very significant for the community
and social development, because it will make the people living
together with sustainable happiness.
This is a qualitative study involving 30 key-informants from two
suburb communities. Data were collected though key-informant
interviews, and analyzed using logical content description and
descriptive statistics.
This research found that on the social quality component, the
people in both communities stressed the procedure for social qualitymaking.
This includes the generousness, sharing and assisting among
people in the communities. These practices helped making people to
live together with sustainable happiness. Living as a family or appear
to be a family is the major social characteristic of these two
communities.
This research also found that form of social quality’s moving
process of both communities stress relation of human and nature;
“nature overpower humans” paradigm and influence of religious
doctrine that emphasizes relations among humans. Both criteria make
the form of social’s moving process simple, adaptive to nature and
caring for opinion sharing and understanding among each other
before action. This form of social quality’s moving process is
composed of 4 steps; (1) awareness building, (2) motivation to
change, (3) participation from every party which is concerned (4)
self-reliance.
Abstract: The fatigue life of tubular joints commonly found in
offshore industry is not only dependent on the value of hot-spot stress
(HSS), but is also significantly influenced by the through-thethickness
stress distribution characterized by the degree of bending
(DoB). The determination of DoB values in a tubular joint is essential
for improving the accuracy of fatigue life estimation using the stresslife
(S–N) method and particularly for predicting the fatigue crack
growth based on the fracture mechanics (FM) approach. In the
present paper, data extracted from finite element (FE) analyses of
tubular KT-joints, verified against experimental data and parametric
equations, was used to investigate the effects of geometrical
parameters on DoB values at the crown 0°, saddle, and crown 180°
positions along the weld toe of central brace in tubular KT-joints
subjected to axial loading. Parametric study was followed by a set of
nonlinear regression analyses to derive DoB parametric formulas for
the fatigue analysis of KT-joints under axial loads. The tubular KTjoint
is a quite common joint type found in steel offshore structures.
However, despite the crucial role of the DoB in evaluating the fatigue
performance of tubular joints, this paper is the first attempt to study
and formulate the DoB values in KT-joints.