Abstract: The production of biodiesel from crude palm oil with
a homogeneous base catalyst is unlikely owing to considerable
formation of soap. Free fatty acids (FFA) in crude palm oil need to
be reduced, e.g. by esterification. This study investigated the activity
of sulfated zirconia calcined at various temperatures for esterification
of FFA in crude palm oil to biodiesel. It was found that under a
proper reaction condition, sulfated zirconia well catalyzes
esterification. FFA content can be reduced to an acceptable value for
typical biodiesel production with a homogeneous base catalyst.
Crystallinity and sulfate attachment of sulfated zirconia depend on
calcination temperature during the catalyst preparation. Too low
temperature of calcination gives amorphous sulfated zirconia which
has low activity for esterification of FFA. In contrast, very high
temperature of calcination removes sulfate group, consequently,
conversion of FFA is reduced. The appropriate temperature range of
calcination is 550-650 oC.
Abstract: This study aims to determine the level of resistance of Hevea brasiliensis and Paraserianthes falcataria (synonym: Falcataria molucana) against wood rot fungi Pleurotus ostreatus based on Indonesian standard SNI 01.7207-2006 and Japanese standard JIS K 1571-2004. The variables measured were visual appearance and weight loss percentage of wood based on longitudinal and cross section fiber directions of rubber wood and sengon wood. Measurement of oven dry weight loss of wood samples performed after 12 weeks incubation. Replication performed was 10 times at each treatment combination. The results based on SNI 01.7207-2006, weight loss value of H. brasiliensis and P. falcataria wood with fiber direction longitudinal were 23,12 and 22,25% respectively and cross section were 20,77 and 18,76% respectively, and all were classified to resistance class IV (no resistance). The results based on JIS K 1571-2004, weight loss value of both woods with fiber direction cross section were 10,95 and 14,20% respectively.
Abstract: With the advent of new technologies, factors related to
mental health in e-workspaces are taken into consideration more than
ever. Studies have revealed that one of the factors affecting the
productivity of employees in an organization is occupational stress.
Another influential factor is quality of work life which is important in
the improvement of work environment conditions and organizational
efficiency. In order to uncover the quality of work life level and to
investigate the impact of occupational stress on quality of work life
among information technology employees in Iran, a cross-sectional
study design was applied and data were gathered using a
questionnaire validated by a group of experts. The results of the study
showed that information technology staffs have average level of both
occupational stress and quality of work life. Furthermore, it was
found that occupational stress has a negative impact on quality of
work life. In addition, the same results were observed for role
ambiguity, role conflict, role under-load, work-pace, work
repetitiveness and tension toward quality of work life. No significant
relation was found between role overload and quality of work life.
Finally, directions for future research are proposed and discussed.
Abstract: In this paper we are interested in classification problems
with a performance constraint on error probability. In such
problems if the constraint cannot be satisfied, then a rejection option
is introduced. For binary labelled classification, a number of SVM
based methods with rejection option have been proposed over the
past few years. All of these methods use two thresholds on the SVM
output. However, in previous works, we have shown on synthetic data
that using thresholds on the output of the optimal SVM may lead to
poor results for classification tasks with performance constraint. In
this paper a new method for supervised classification with rejection
option is proposed. It consists in two different classifiers jointly
optimized to minimize the rejection probability subject to a given
constraint on error rate. This method uses a new kernel based linear
learning machine that we have recently presented. This learning
machine is characterized by its simplicity and high training speed
which makes the simultaneous optimization of the two classifiers
computationally reasonable. The proposed classification method with
rejection option is compared to a SVM based rejection method
proposed in recent literature. Experiments show the superiority of
the proposed method.
Abstract: With the popularity of the multi-core and many-core architectures there is a great requirement for software frameworks which can support parallel programming methodologies. In this paper we introduce an Eclipse toolkit, JConqurr which is easy to use and provides robust support for flexible parallel progrmaming. JConqurr is a multi-core and many-core programming toolkit for Java which is capable of providing support for common parallel programming patterns which include task, data, divide and conquer and pipeline parallelism. The toolkit uses an annotation and a directive mechanism to convert the sequential code into parallel code. In addition to that we have proposed a novel mechanism to achieve the parallelism using graphical processing units (GPU). Experiments with common parallelizable algorithms have shown that our toolkit can be easily and efficiently used to convert sequential code to parallel code and significant performance gains can be achieved.
Abstract: The objective of this paper is to investigate a new
approach based on the idea of pictograms for food portion size. This
approach adopts the model of the United States Pharmacopeia- Drug
Information (USP-DI). The representation of each food portion size
composed of three parts: frame, the connotation of dietary portion
sizes and layout. To investigate users- comprehension based on this
approach, two experiments were conducted, included 122 Taiwanese
people, 60 male and 62 female with ages between 16 and 64 (divided
into age groups of 16-30, 31-45 and 46-64). In Experiment 1, the mean
correcting rate of the understanding level of food items is 48.54%
(S.D.= 95.08) and the mean response time 2.89sec (S.D.=2.14). The
difference on the correct rates for different age groups is significant
(P*=0.00
Abstract: In this paper, a worm-like micro robot designed for inpipe
application with intelligent active force control (AFC) capability
is modelled and simulated. The motion of the micro robot is based on
an impact drive mechanism (IDM) that is actuated using piezoelectric
device. The trajectory tracking performance of the modelled micro
robot is initially experimented via a conventional proportionalintegral-
derivative (PID) controller in which the dynamic response of
the robot system subjected to different input excitations is
investigated. Subsequently, a robust intelligent method known as
active force control with fuzzy logic (AFCFL) is later incorporated
into the PID scheme to enhance the system performance by
compensating the unwanted disturbances due to the interaction of the
robot with its environment. Results show that the proposed AFCFL
scheme is far superior than the PID control counterpart in terms of
the system-s tracking capability in the wake of the disturbances.
Abstract: This paper proposes a novel hybrid algorithm for feature selection based on a binary ant colony and SVM. The final subset selection is attained through the elimination of the features that produce noise or, are strictly correlated with other already selected features. Our algorithm can improve classification accuracy with a small and appropriate feature subset. Proposed algorithm is easily implemented and because of use of a simple filter in that, its computational complexity is very low. The performance of the proposed algorithm is evaluated through a real Rotary Cement kiln dataset. The results show that our algorithm outperforms existing algorithms.
Abstract: Aggressive scaling of MOS devices requires use of ultra-thin gate oxides to maintain a reasonable short channel effect and to take the advantage of higher density, high speed, lower cost etc. Such thin oxides give rise to high electric fields, resulting in considerable gate tunneling current through gate oxide in nano regime. Consequently, accurate analysis of gate tunneling current is very important especially in context of low power application. In this paper, a simple and efficient analytical model has been developed for channel and source/drain overlap region gate tunneling current through ultra thin gate oxide n-channel MOSFET with inevitable deep submicron effect (DSME).The results obtained have been verified with simulated and reported experimental results for the purpose of validation. It is shown that the calculated tunnel current is well fitted to the measured one over the entire oxide thickness range. The proposed model is suitable enough to be used in circuit simulator due to its simplicity. It is observed that neglecting deep sub-micron effect may lead to large error in the calculated gate tunneling current. It is found that temperature has almost negligible effect on gate tunneling current. It is also reported that gate tunneling current reduces with the increase of gate oxide thickness. The impact of source/drain overlap length is also assessed on gate tunneling current.
Abstract: We propose a new approach on how to obtain the approximate solutions of Hamilton-Jacobi (HJ) equations. The process of the approximation consists of two steps. The first step is to transform the HJ equations into the virtual time based HJ equations (VT-HJ) by introducing a new idea of ‘virtual-time’. The second step is to construct the approximate solutions of the HJ equations through a computationally iterative procedure based on the VT-HJ equations. It should be noted that the approximate feedback solutions evolve by themselves as the virtual-time goes by. Finally, we demonstrate the effectiveness of our approximation approach by means of simulations with linear and nonlinear control problems.
Abstract: The growing health hazardous impact of arsenic (As)
contamination in environment is the impetus of the present
investigation. Application of lactic acid bacteria (LAB) for the
removal of toxic and heavy metals from water has been reported.
This study was performed in order to isolate and characterize the Asresistant
LAB from mud and sludge samples for using as efficient As
uptaking probiotic. Isolation of As-resistant LAB colonies was
performed by spread plate technique using bromocresol purple
impregnated-MRS (BP-MRS) agar media provided with As @ 50
μg/ml. Isolated LAB were employed for probiotic characterization
process, acid and bile tolerance, lactic acid production, antibacterial
activity and antibiotic tolerance assays. After As-resistant and
removal characterizations, the LAB were identified using 16S rDNA
sequencing. A total of 103 isolates were identified as As-resistant
strains of LAB. The survival of 6 strains (As99-1, As100-2, As101-3,
As102-4, As105-7, and As112-9) was found after passing through the
sequential probiotic characterizations. Resistant pattern pronounced
hollow zones at As concentration >2000 μg/ml in As99-1, As100-2,
and As101-3 LAB strains, whereas it was found at ~1000 μg/ml in
rest 3 strains. Among 6 strains, the As uptake efficiency of As102-4
(0.006 μg/h/mg wet weight of cell) was higher (17 – 209%)
compared to remaining LAB. 16S rDNA sequencing data of 3 (As99-
1, As100-2, and As101-3) and 3 (As102-4, As105-7, and As112-9)
LAB strains clearly showed 97 to 99% (340 bp) homology to
Pediococcus dextrinicus and Pediococcus acidilactici, respectively.
Though, there was no correlation between the metal resistant and
removal efficiency of LAB examined but identified elevated As
removing LAB would probably be a potential As uptaking probiotic
agent. Since present experiment concerned with only As removal
from pure water, As removal and removal mechanism in natural
condition of intestinal milieu should be assessed in future studies.
Abstract: Harmonic pollution and low power factor in power
systems caused by power converters have been of great concern. To
overcome these problems several converter topologies using
advanced semiconductor devices and control schemes have been
proposed. This investigation is to identify a low cost, small size,
efficient and reliable ac to dc converter to meet the input performance
index of UPS. The performance of single phase and three phase ac to
dc converter along with various control techniques are studied and
compared. The half bridge converter topology with linear current
control is identified as most suitable. It is simple, energy efficient
because of single switch power loss and transformer-less operation of
UPS. The results are validated practically using a prototype built
using IGBT and analog controller. The performance for both single
and three-phase system is verified. Digital implementation of closed
loop control achieves higher reliability. Its cost largely depends on
chosen bit precision. The minimal bit precision for optimum
converter performance is identified as 16-bit with fixed-point
operation. From the investigation and practical implementation it is
concluded that half bridge ac – dc converter along with digital linear
controller meets the performance index of UPS for single and three
phase systems.
Abstract: Pre-germinated parboiled brown rice or Khao hang (in Thai) is paddy which undergoing the processes of soaking, steaming, drying and dehusking to obtain the edible form for consumption. The objectives of this research were to study the kinetic of pre-germinated parboiled brown rice drying using fluidization technique and to study the properties of pre-germinated parboiled brown rice after drying. The dryings were performed at the different temperatures of 110, 120 and 130 oC at the bed depth of 2 cm with the air velocity of 1.98 m/s. The results found that the higher drying temperature led to the faster moisture reduction. After drying until the moisture content of pre-germinated parboiled brown rice was lower than 14%wet basis, samples were taken to determine various qualities such as percentage of head rice and L* a* b* color values. The shade drying was used as a control. The results found that the higher drying temperature resulted in the decrease of head rice percentage. For the color assessment, the trend of L* and a* values was increased with the drying temperature, while the b* value was not significantly difference (p › 0.05) by drying temperatures. However, the b value of drying by fluidized bed dryer was higher than the control.
Abstract: In Geographic Information System, one of the sources
of obtaining needed geographic data is digitizing analog maps and
evaluation of aerial and satellite photos. In this study, a method will
be discussed which can be used to extract vectorial features and
creating vectorized drawing files for aerial photos. At the same time
a software developed for these purpose. Converting from raster to
vector is also known as vectorization and it is the most important step
when creating vectorized drawing files. In the developed algorithm,
first of all preprocessing on the aerial photo is done. These are;
converting to grayscale if necessary, reducing noise, applying some
filters and determining the edge of the objects etc. After these steps,
every pixel which constitutes the photo are followed from upper left
to right bottom by examining its neighborhood relationship and one
pixel wide lines or polylines obtained. The obtained lines have to be
erased for preventing confusion while continuing vectorization
because if not erased they can be perceived as new line, but if erased
it can cause discontinuity in vector drawing so the image converted
from 2 bit to 8 bit and the detected pixels are expressed as a different
bit. In conclusion, the aerial photo can be converted to vector form
which includes lines and polylines and can be opened in any CAD
application.
Abstract: Fault-proneness of a software module is the
probability that the module contains faults. A correlation exists
between the fault-proneness of the software and the measurable
attributes of the code (i.e. the static metrics) and of the testing (i.e.
the dynamic metrics). Early detection of fault-prone software
components enables verification experts to concentrate their time and
resources on the problem areas of the software system under
development. This paper introduces Genetic Algorithm based
software fault prediction models with Object-Oriented metrics. The
contribution of this paper is that it has used Metric values of JEdit
open source software for generation of the rules for the classification
of software modules in the categories of Faulty and non faulty
modules and thereafter empirically validation is performed. The
results shows that Genetic algorithm approach can be used for
finding the fault proneness in object oriented software components.
Abstract: So much energy is used in high rise buildings to fulfill
the basic needs of users such as lighting and thermal comfort.
Malaysia has hot and humid climate, buildings especially high rise
buildings receive unnecessary solar radiation that cause more solar
heat gain. Energy use specially electricity consumption in high rise
buildings has increased. There have been growing concerns about
energy consumption and its effect on environment. Building, energy
and the environment are important issues that the designers should
consider to them. Self protected form is one of possible ways against
the impact of solar radiation in high rise buildings. The Energy
performance of building envelopes was investigated in term of the
Overall Thermal Transfer Value (OTTV ).In this paper, the amount
of OTTV reduction was calculated through OTTV Equations to
clear the effectiveness of self shading strategy on minimizing energy
consumption for cooling interior spaces in high rise buildings which
has considerable envelope areas against solar radiation. Also increasing
the optimum window area was investigated using self-shading
strategy in designing high rise buildings. As result, the significant
reduction in OTTV was shown based on WWR.In addition slight
increase was demonstrated in WWR that can influence on visible
comfort interior spaces.
Abstract: With the advance of multimedia and diagnostic
images technologies, the number of radiographic images is increasing
constantly. The medical field demands sophisticated systems for
search and retrieval of the produced multimedia document. This
paper presents an ongoing research that focuses on the semantic
content of radiographic image documents to facilitate semantic-based
radiographic image indexing and a retrieval system. The proposed
model would divide a radiographic image document, based on its
semantic content, and would be converted into a logical structure or
a semantic structure. The logical structure represents the overall
organization of information. The semantic structure, which is bound
to logical structure, is composed of semantic objects with
interrelationships in the various spaces in the radiographic image.
Abstract: Today-s healthcare industries had become more
patient-centric than profession-centric, from which the issues of quality of healthcare and the patient safety are the major concerns in the modern healthcare facilities. An unplanned extubation (UE) may
be detrimental to the patient-s life, and thus is one of the major indexes
of patient safety and healthcare quality. A high UE rate not only
defeated the healthcare quality as well as the patient safety policy but
also the nurses- morality, and job satisfaction. The UE problem in a psychiatric hospital is unique and may be a tough challenge for the
healthcare professionals for the patients were mostly lacking communication capabilities. We reported with this essay a particular
project that was organized to reduce the UE rate from the current 2.3%
to a lower and satisfactory level in the long-term care units of a psychiatric hospital. The project was conducted between March 1st,
2011 and August 31st, 2011. Based on the error information gathered
from varied units of the hospital, the team analyzed the root causes
with possible solutions proposed to the meetings. Four solutions were
then concluded with consensus and launched to the units in question.
The UE rate was now reduced to a level of 0.17%. Experience from
this project, the procedure and the tools adopted would be good reference to other hospitals.
Abstract: An effort has been taken to simulate the combustion
and performance characteristics of biodiesel fuel in direct injection
(D.I) low heat rejection (LHR) diesel engine. Comprehensive
analyses on combustion characteristics such as cylinder pressure,
peak cylinder pressure, heat release and performance characteristics
such as specific fuel consumption and brake thermal efficiency are
carried out. Compression ignition (C.I) engine cycle simulation was
developed and modified in to LHR engine for both diesel and
biodiesel fuel. On the basis of first law of thermodynamics the
properties at each degree crank angle was calculated. Preparation and
reaction rate model was used to calculate the instantaneous heat
release rate. A gas-wall heat transfer calculations are based on the
ANNAND-s combined heat transfer model with instantaneous wall
temperature to analyze the effect of coating on heat transfer. The
simulated results are validated by conducting the experiments on the
test engine under identical operating condition on a turbocharged D.I
diesel engine. In this analysis 20% of biodiesel (derived from
Jatropha oil) blended with diesel and used in both conventional and
LHR engine. The simulated combustion and performance
characteristics results are found satisfactory with the experimental
value.
Abstract: A numerical study of flow in a horizontally channel
partially filled with a porous screen with non-uniform inlet has been
performed by lattice Boltzmann method (LBM). The flow in porous
layer has been simulated by the Brinkman-Forchheimer model.
Numerical solutions have been obtained for variable porosity models
and the effects of Darcy number and porosity have been studied in
detail. It is found that the flow stabilization is reliant on the Darcy
number. Also the results show that the stabilization of flow field and
heat transfer is depended to Darcy number. Distribution of stream
field becomes more stable by decreasing Darcy number. Results
illustrate that the effect of variable porosity is significant just in the
region of the solid boundary. In addition, difference between constant
and variable porosity models is decreased by decreasing the Darcy
number.