Abstract: This study is about the structural transformations of
aluminium examining with the Dynamic Mechanical Thermal
Analyzer (DMTA). It is a faster and simpler measuring method to
make consequence about the metal’s structural transformations. The
device measures the changing of the mechanical characteristics
depending on the heating rate, and concludes certain transformations.
This measuring method fast and shows clean-cut results comparing
the conventional ways.
Applying polymer measuring devices for metal investigations is
not widespread method. One of the adaptable ways is shown in this
study. The article compares the results of the small specimen test and
the DMTA method, considering the temperature and the forming
dependence of recrystallization temperature.
Abstract: Grid is an environment with millions of resources
which are dynamic and heterogeneous in nature. A computational
grid is one in which the resources are computing nodes and is meant
for applications that involves larger computations. A scheduling
algorithm is said to be efficient if and only if it performs better
resource allocation even in case of resource failure. Resource
allocation is a tedious issue since it has to consider several
requirements such as system load, processing cost and time, user’s
deadline and resource failure. This work attempts in designing a
resource allocation algorithm which is cost-effective and also targets
at load balancing, fault tolerance and user satisfaction by considering
the above requirements. The proposed Budget Constrained Load
Balancing Fault Tolerant algorithm with user satisfaction (BLBFT)
reduces the schedule makespan, schedule cost and task failure rate
and improves resource utilization. Evaluation of the proposed
BLBFT algorithm is done using Gridsim toolkit and the results are
compared with the algorithms which separately concentrates on all
these factors. The comparison results ensure that the proposed
algorithm works better than its counterparts.
Abstract: Transmission system performance analysis is vital to
proper planning and operations of power systems in the presence of
deregulation. Key performance indicators (KPIs) are often used as
measure of degree of performance. This paper gives a novel method
to determine the transmission efficiency by evaluating the ratio of
real power losses incurred from a specified transfer direction.
Available Transmission Transfer Efficiency (ATTE) expresses the
percentage of real power received resulting from inter-area available
power transfer. The Tie line (Rated system path) performance is seen
to differ from system wide (Network response) performance and
ATTE values obtained are transfer direction specific. The required
sending end quantities with specified receiving end ATC and the
receiving end power circle diagram are obtained for the tie line
analysis. The amount of real power loss load relative to the available
transfer capability gives a measure of the transmission grid
efficiency.
Abstract: We report the microstructural and magnetic properties
of Ni50Mn39Sn11 and Ni50Mn36Sn14 ribbon Heusler alloys.
Experimental results were obtained by differential scanning
calorymetry, X-ray diffraction and vibrating sample magnetometry
techniques. The Ni-Mn-Sn system undergoes a martensitic structural
transformation in a wide temperature range. For example, for
Ni50Mn39Sn11 the start and finish temperatures of the martensitic and
austenite phase transformation for ribbon alloy were Ms=336K,
Mf=328K, As=335K and Af=343K whereas no structural
transformation is observed for Ni50Mn36Sn14 alloys. Magnetic
measurements show the typical ferromagnetic behavior with Curie
temperature 207 K at low applied field of 50 Oe. The complex
behavior exhibited by these Heusler alloys should be ascribed to the
strong coupling between magnetism and structure, being their
magnetic behavior determined by the distance between Mn atoms.
Abstract: An Australian manufacturer has fabricated an
innovative GFRP sandwich panel made from E-glass fiber skin and a
modified phenolic core for structural applications. Debonding, which
refers to separation of skin from the core material in composite
sandwiches, is one of the most common types of damage in
composites. The presence of debonding is of great concern because it
not only severely affects the stiffness but also modifies the dynamic
behaviour of the structure. Generally it is seen that the majority of
research carried out has been concerned about the delamination of
laminated structures whereas skin-core debonding has received
relatively minor attention. Furthermore it is observed that research
done on composite slabs having multiple skin-core debonding is very
limited. To address this gap, a comprehensive research investigating
dynamic behaviour of composite panels with single and multiple
debonding is presented. The study uses finite-element modelling and
analyses for investigating the influence of debonding on free
vibration behaviour of single and multilayer composite sandwich
panels. A broad parametric investigation has been carried out by
varying debonding locations, debonding sizes and support conditions
of the panels in view of both single and multiple debonding.
Numerical models were developed with Strand7 finite element
package by innovatively selecting the suitable elements to diligently
represent their actual behavior. Three-dimensional finite element
models were employed to simulate the physically real situation as
close as possible, with the use of an experimentally and numerically
validated finite element model. Comparative results and conclusions
based on the analyses are presented. For similar extents and locations
of debonding, the effect of debonding on natural frequencies appears
greatly dependent on the end conditions of the panel, giving greater
decrease in natural frequency when the panels are more restrained.
Some modes are more sensitive to debonding and this sensitivity
seems to be related to their vibration mode shapes. The fundamental
mode seems generally the least sensitive mode to debonding with
respect to the variation in free vibration characteristics. The results
indicate the effectiveness of the developed three dimensional finite
element models in assessing debonding damage in composite
sandwich panels.
Abstract: Availability of different genetic tests after completion
of Human Genome Project increases the physicians’ responsibility to
keep themselves update on the potential implementation of these
genetic tests in their daily practice. However, due to numbers of
barriers, still many of physicians are not either aware of these tests or
are not willing to offer or refer their patients for genetic tests. This
study was conducted an anonymous, cross-sectional, mailed-based
survey to develop a primary data of Malaysian physicians’ level of
knowledge and perception of gene profiling. Questionnaire had 29
questions. Total scores on selected questions were used to assess the
level of knowledge. The highest possible score was 11. Descriptive
statistics, one way ANOVA and chi-squared test was used for
statistical analysis. Sixty three completed questionnaires were
returned by 27 general practitioners (GPs) and 36 medical specialists.
Responders’ age ranges from 24 to 55 years old (mean 30.2 ± 6.4).
About 40% of the participants rated themselves as having poor level
of knowledge in genetics in general whilst 60% believed that they
have fair level of knowledge; however, almost half (46%) of the
respondents felt that they were not knowledgeable about available
genetic tests. A majority (94%) of the responders were not aware of
any lab or company which is offering gene profiling services in
Malaysia. Only 4% of participants were aware of using gene profiling
for detection of dosage of some drugs. Respondents perceived greater
utility of gene profiling for breast cancer (38%) compared to the
colorectal familial cancer (3%). The score of knowledge ranged from
2 to 8 (mean 4.38 ± 1.67). Non- significant differences between score
of knowledge of GPs and specialists were observed, with score of
4.19 and 4.58 respectively. There was no significant association
between any demographic factors and level of knowledge. However,
those who graduated between years 2001 to 2005 had higher level of
knowledge. Overall, 83% of participants showed relatively high level
of perception on value of gene profiling to detect patient’s risk of
disease. However, low perception was observed for both statements
of using gene profiling for general population in order to alter their
lifestyle (25%) as well as having the full sequence of a patient
genome for the purpose of determining a patient’s best match for
treatment (18%). The lack of clinical guidelines, limited provider
knowledge and awareness, lack of time and resources to educate
patients, lack of evidence-based clinical information and cost of tests
were the most barriers of ordering gene profiling mentioned by
physicians. In conclusion Malaysian physicians who participate in
this study had mediocre level of knowledge and awareness in gene
profiling. The low exposure to the genetic questions and problems
might be a key predictor of lack of awareness and knowledge on
available genetic tests. Educational and training workshop might be useful in helping Malaysian physicians incorporate genetic profiling
into practice for eligible patients.
Abstract: The effects of the pumping wavelength and their power
on the gain flattening of a fiber Raman amplifier (FRA) are
investigated. The multi-wavelength pumping scheme is utilized to
achieve gain flatness in FRA. It is proposed that gain flatness
becomes better with increase in number of pumping wavelengths
applied. We have achieved flat gain with 0.27 dB fluctuation in a
spectral range of 1475-1600 nm for a Raman fiber length of 10 km by
using six pumps with wavelengths with in the 1385-1495 nm interval.
The effect of multi-wavelength pumping scheme on gain saturation in
FRA is also studied. It is proposed that gain saturation condition gets
improved by using this scheme and this scheme is more useful for
higher spans of Raman fiber length.
Abstract: Coal fly ash is formed as a solid waste product from
the combustion of coal in coal fired power stations. Huge amounts of
fly ash are produced globally every year and are predicted to
increase. Nowadays, less than half of the fly ash is used as a raw
material for cement manufacturing, construction and the rest of it is
disposed as a waste causing yet another environmental concern. For
this reason, the recycling of this kind of slurries into useful materials
is quite important in terms of economical and environmental aspects.
The purpose of this study is to evaluate the Orhaneli and
Tuncbilek coal fly ashes for utilization in some industrial
applications. Therefore the mineralogical and chemical compositions
of these fly ashes were analyzed by X-ray fluorescence spectroscopy,
ourier-transform infrared spectrometer, and X-ray diffraction. The
silicon (Si) and aluminum (Al) in the fly ashes were activated by
alkali fusion technique with sodium hydroxide. The obtained extracts
were analyzed for Si and Al content by inductively coupled plasma
optical emission spectrometry.
Abstract: In this study, out-of-plane free vibrations of a circular
rods is investigated theoretically. The governing equations for
naturally twisted and curved spatial rods are obtained using
Timoshenko beam theory and rewritten for circular rods. Effects of
the axial and shear deformations are considered in the formulations.
Ordinary differential equations in scalar form are solved analytically
by using transfer matrix method. The circular rods of the mass matrix
are obtained by using straight rod of consistent mass matrix. Free
vibrations frequencies obtained by solving eigenvalue problem. A
computer program coded in MATHEMATICA language is prepared.
Circular beams are analyzed through various examples for free
vibrations analysis. Results are compared with ANSYS results based
on finite element method and available in the literature.
Abstract: This study was carried out to investigate the adverse
effect of industrial wastewater on surface water quality in Gebeng
industrial estate, Pahang, Malaysia. Surface water was collected from
six sampling stations. Physicochemical parameters were
characterized based on in-situ and ex-situ analysis according to
standard methods by American Public Health Association (APHA).
Selected heavy metals were determined by using Inductively Coupled
Plasma Mass Spectrometry (ICP MS). The results revealed that the
concentration of heavy metals such as Pb, Cu, Cd, Cr and Hg were
high in samples. The results also showed that the value of Pb and Hg
were higher in the wet season in comparison to dry season.
According to Malaysia National Water Quality Standard (NWQS)
and Water Quality Index (WQI) all the sampling station were
categorized as class IV (highly polluted). The present study revealed
that the adverse effects of careless disposal of wastes and directly
discharge of effluents affected on surface water quality. Therefore,
the authorities should implement the laws to ensure the proper
practices of wastewater management for environmental sustainability
around the study area.
Abstract: The present research work investigates the seismic
response of reinforced concrete (RC) frame building considering the
effect of modeling masonry infill (MI) walls. The seismic behavior of
a residential 6-storey RC frame building, considering and ignoring
the effect of masonry, is numerically investigated using response
spectrum (RS) analysis. The considered herein building is designed
as a moment resisting frame (MRF) system following the Egyptian
code (EC) requirements. Two developed models in terms of bare
frame and infill walls frame are used in the study. Equivalent
diagonal strut methodology is used to represent the behavior of infill
walls, whilst the well-known software package ETABS is used for
implementing all frame models and performing the analysis. The
results of the numerical simulations such as base shear,
displacements, and internal forces for the bare frame as well as the
infill wall frame are presented in a comparative way. The results of
the study indicate that the interaction between infill walls and frames
significantly change the responses of buildings during earthquakes
compared to the results of bare frame building model. Specifically,
the seismic analysis of RC bare frame structure leads to
underestimation of base shear and consequently damage or even
collapse of buildings may occur under strong shakings. On the other
hand, considering infill walls significantly decrease the peak floor
displacements and drifts in both X and Y-directions.
Abstract: Pipa is one of the most important Chinese traditional
plucked instruments, but its directivity has never been measured
systematically. In western, directivity of loudness for western
instruments is deeply researched through analysis of sound pressure
level, whereas the directivity of timbre is seldom studied. In this paper,
a new method for directivity of timbre was proposed, and horizontal
directivity patterns of loudness and timbre of Pipa were measured.
Directivity of Pipa radiation was measured in an anechoic room. The
sound of Pipa played by a musician was recorded simultaneously by
32 microphones with Pipa in the center. The measuring results were
examined through listening test. According to the measurement of
Pipa directivity radiation, we put forward the best localization of Pipa
in the Chinese traditional orchestra and the optimal recording region.
Abstract: The Aptima® HIV-1 Quant Dx Assay is a fully
automated assay on the Panther system. It is based on Transcription-
Mediated Amplification and real time detection technologies. This
assay is intended for monitoring HIV-1 viral load in plasma
specimens and for the detection of HIV-1 in plasma and serum
specimens.
Nine-hundred and seventy nine specimens selected at random
from routine testing at St Thomas’ Hospital, London were
anonymised and used to compare the performance of the Aptima
HIV-1 Quant Dx assay and Roche COBAS® AmpliPrep/COBAS®
TaqMan® HIV-1 Test, v2.0. Two-hundred and thirty four specimens
gave quantitative HIV-1 viral load results in both assays. The
quantitative results reported by the Aptima Assay were comparable to
those reported by the Roche COBAS AmpliPrep/COBAS TaqMan
HIV-1 Test, v2.0 with a linear regression slope of 1.04 and an
intercept on -0.097.
The Aptima assay detected HIV-1 in more samples than the
COBAS assay. This was not due to lack of specificity of the Aptima
assay because this assay gave 99.83% specificity on testing plasma
specimens from 600 HIV-1 negative individuals. To understand the
reason for this higher detection rate a side-by-side comparison of low
level panels made from the HIV-1 3rd international standard
(NIBSC10/152) and clinical samples of various subtypes were tested
in both assays. The Aptima assay was more sensitive than the
COBAS assay.
The good sensitivity, specificity and agreement with other
commercial assays make the HIV-1 Quant Dx Assay appropriate for
both viral load monitoring and detection of HIV-1 infections.
Abstract: Technology, multimedia in Open Educational
Resources, can contribute positively to student performance in an
online instructional environment. Student performance data of past
four years were obtained from an online course entitled Applied
Calculus (MA139). This paper examined the data to determine
whether multimedia (independent variable) had any impact on
student performance (dependent variable) in online math learning,
and how students felt about the value of the technology. Two groups
of student data were analyzed, group 1 (control) from the online
applied calculus course that did not use multimedia instructional
materials, and group 2 (treatment) of the same online applied calculus
course that used multimedia instructional materials. For the MA139
class, results indicate a statistically significant difference (p = .001)
between the two groups, where group 1 had a final score mean of
56.36 (out of 100), group 2 of 70.68. Additionally, student
testimonials were discussed in which students shared their experience
in learning applied calculus online with multimedia instructional
materials.
Abstract: In this paper, we will analyze the relationship between the neo-liberal concept of property rights and redistribution policy. This issue is back in the focus of interest due to the crisis 2008. The crisis has reaffirmed the influence of the state on the free-market processes. The interference of the state with property relations reopened a classical question: is it legitimate to redistribute resources of a man in favor of another man with taxes? The dominant view is that the neoliberal philosophy of natural rights is incompatible with redistributive measures. In principle, this view can be accepted. However, when we look into the details of the theory of natural rights proposed by some coryphaei of neoliberal philosophy, such as Hayek, Nozick, Buchanan and Rothbard, we can see that it is not such an unequivocal view.
Abstract: The main objective of incorporating natural fibers such as Henequen microfibers (NF) into the High Density Polyethylene (HDPE) polymer matrix is to reduce the cost and to enhance the mechanical as well as other properties. The Henequen microfibers were chopped manually to 5-7mm in length and added into the polymer matrix at the optimized concentration of 8 wt %. In order to facilitate the link between Henequen microfibers (NF) and HDPE matrix, coupling agent such as Glycidoxy (Epoxy) Functional Methoxy Silane (GPTS) at various concentrations from 0.1%, 0.3%, 0.5%, 0.7%, 0.9% and 1% by weight to the total fibers were added. The tensile strength of the composite increased marginally while % elongation at break of the composites decreased with increase in silane loading by wt %. Tensile modulus and stiffness observed increased at 0.9 wt % GPTS loading. Flexural as well as impact strength of the composite decreased with increase in GPTS loading by weight %. Dielectric strength of the composite also found increased marginally up to 0.5wt % silane loading and thereafter remained constant.
Abstract: Image enhancement is a challenging issue in many applications. In the last two decades, there are various filters developed. This paper proposes a novel method which removes Gaussian noise from the gray scale images. The proposed technique is compared with Enhanced Fuzzy Peer Group Filter (EFPGF) for various noise levels. Experimental results proved that the proposed filter achieves better Peak-Signal-to-Noise-Ratio PSNR than the existing techniques. The proposed technique achieves 1.736dB gain in PSNR than the EFPGF technique.
Abstract: Chrome tannery wastewater causes serious environmental hazard due to its high pollution potential. As a result, rigorous treatment is necessary for abatement of pollution from this type of wastewater. There are many research studies on chrome tannery wastewater treatment in the field of physical, chemical, and biological methods. In general, biological treatment process is found ineffective for direct application because of adverse effects by toxic chromium, sulphide, chloride etc. However, biological methods were employed mainly for a few sub processes generating significant amount of organic matter and without chromium, chlorides etc. In this context the present paper reviews the characteristics feature and pollution potential of wastewater generated from chrome tannery units and treatment of the same. The different biological processes used earlier and their chronological development for treatment of the chrome tannery wastewater are thoroughly reviewed in this paper. In this regard, the scope of hybrid bioreactor - an advanced technology option has also been explored, as this kind of treatment is well suited for the wastewater having inhibitory substances.
Abstract: In this study, ultrasonic assisted machining (UAM) technique is applied in side-surface milling experiment for glass-ceramic workpiece material. The tungsten carbide cutting-tool with diamond coating is used in conjunction with two kinds of cooling/lubrication mediums such as water-soluble (WS) cutting fluid and minimum quantity lubricant (MQL). Full factorial process parameter combinations on the milling experiments are planned to investigate the effect of process parameters on cutting performance. From the experimental results, it tries to search for the better process parameter combination which the edge-indentation and the surface roughness are acceptable. In the machining experiments, ultrasonic oscillator was used to excite a cutting-tool along the radial direction producing a very small amplitude of vibration frequency of 20KHz to assist the machining process. After processing, toolmaker microscope was used to detect the side-surface morphology, edge-indentation and cutting tool wear under different combination of cutting parameters, and analysis and discussion were also conducted for experimental results. The results show that the main leading parameters to edge-indentation of glass ceramic are cutting depth and feed rate. In order to reduce edge-indentation, it needs to use lower cutting depth and feed rate. Water-soluble cutting fluid provides a better cooling effect in the primary cutting area; it may effectively reduce the edge-indentation and improve the surface morphology of the glass ceramic. The use of ultrasonic assisted technique can effectively enhance the surface finish cleanness and reduce cutting tool wear and edge-indentation.
Abstract: The principle of the seismic performance evaluation methods is to provide a measure of capability for a building or set of buildings to be damaged by an earthquake. The common objective of many of these methods is to supply classification criteria. The purpose of this study is to present a method for assessing the seismic performance of structures, based on Pushover method; we are particularly interested in reinforced concrete frame structures, which represent a significant percentage of damaged structures after a seismic event. The work is based on the characterization of seismic movement of the various earthquake zones in terms of PGA and PGD that is obtained by means of SIMQK_GR and PRISM software and the correlation between the points of performance and the scalar characterizing the earthquakes will developed.