Abstract: Electric vehicle (EV) is one of the effective solutions to
control emission of greenhouses gases in the world. It is of interest
for future transportation due to its sustainability and efficiency by
automotive manufacturers. Various electrical motors have been used
for propulsion system of electric vehicles in last decades. In this
paper brushed DC motor, Induction motor (IM), switched reluctance
motor (SRM) and brushless DC motor (BLDC) are simulated and
compared. BLDC motor is recommended for high performance
electric vehicles. PWM switching technique is implemented for speed
control of BLDC motor. Behavior of different modes of PWM speed
controller of BLDC motor are simulated in MATLAB/SIMULINK.
BLDC motor characteristics are compared and discussed for various
PWM switching modes under normal and inverter fault conditions.
Comparisons and discussions are verified through simulation results.
Abstract: Electroencephalogram (EEG) recordings are often
contaminated with ocular and muscle artifacts. In this paper, the
canonical correlation analysis (CCA) is used as blind source
separation (BSS) technique (BSS-CCA) to decompose the artifact
contaminated EEG into component signals. We combine the BSSCCA
technique with wavelet filtering approach for minimizing both
ocular and muscle artifacts simultaneously, and refer the proposed
method as wavelet enhanced BSS-CCA. In this approach, after
careful visual inspection, the muscle artifact components are
discarded and ocular artifact components are subjected to wavelet
filtering to retain high frequency cerebral information, and then clean
EEG is reconstructed. The performance of the proposed wavelet
enhanced BSS-CCA method is tested on real EEG recordings
contaminated with ocular and muscle artifacts, for which power
spectral density is used as a quantitative measure. Our results suggest
that the proposed hybrid approach minimizes ocular and muscle
artifacts effectively, minimally affecting underlying cerebral activity
in EEG recordings.
Abstract: In this paper, we evaluate the choice of suitable
quantization characteristics for both the decoder messages and the
received samples in Low Density Parity Check (LDPC) coded
systems using M-QAM (Quadrature Amplitude Modulation)
schemes. The analysis involves the demapper block that provides
initial likelihood values for the decoder, by relating its quantization
strategy of the decoder. A mapping strategy refers to the grouping of
bits within a codeword, where each m-bit group is used to select a
2m-ary signal in accordance with the signal labels. Further we
evaluate the system with mapping strategies like Consecutive-Bit
(CB) and Bit-Reliability (BR). A new demapper version, based on
approximate expressions, is also presented to yield a low complexity
hardware implementation.
Abstract: This paper presents a pulse doubling technique in a 12-pulse ac-dc converter which supplies direct torque controlled motor drives (DTCIMD-s) in order to have better power quality conditions at the point of common coupling. The proposed technique increases the number of rectification pulses without significant changes in the installations and yields in harmonic reduction in both ac and dc sides. The 12-pulse rectified output voltage is accomplished via two paralleled six-pulse ac-dc converters each of them consisting of three-phase diode bridge rectifier. An autotransformer is designed to supply the rectifiers. The design procedure of magnetics is in a way such that makes it suitable for retrofit applications where a six-pulse diode bridge rectifier is being utilized. Independent operation of paralleled diode-bridge rectifiers, i.e. dc-ripple re-injection methodology, requires a Zero Sequence Blocking Transformer (ZSBT). Finally, a tapped interphase reactor is connected at the output of ZSBT to double the pulse numbers of output voltage up to 24 pulses. The aforementioned structure improves power quality criteria at ac mains and makes them consistent with the IEEE-519 standard requirements for varying loads. Furthermore, near unity power factor is obtained for a wide range of DTCIMD operation. A comparison is made between 6- pulse, 12-pulse, and proposed converters from view point of power quality indices. Results show that input current total harmonic distortion (THD) is less than 5% for the proposed topology at various loads.
Abstract: The brain MR imaging-based clinical research and analysis system were specifically built and the development for a large-scale data was targeted. We used the general clinical data available for building large-scale data. Registration period for the selection of the lesion ROI and the region growing algorithm was used and the Mesh-warp algorithm for matching was implemented. The accuracy of the matching errors was modified individually. Also, the large ROI research data can accumulate by our developed compression method. In this way, the correctly decision criteria to the research result was suggested. The experimental groups were age, sex, MR type, patient ID and smoking which can easily be queries. The result data was visualized of the overlapped images by a color table. Its data was calculated by the statistical package. The evaluation for the utilization of this system in the chronic ischemic damage in the area has done from patients with the acute cerebral infarction. This is the cause of neurologic disability index location in the center portion of the lateral ventricle facing. The corona radiate was found in the position. Finally, the system reliability was measured both inter-user and intra-user registering correlation.
Abstract: The results show that the bridge equipped with seismic isolation bearing system shows a high amount of energy dissipation. The purpose of the present study is to analyze the overall performance of continuous curved highway viaducts with different bearing supports, with an emphasis on the effectiveness of seismic isolation based on lead rubber bearing and hedge reaction force bearing system consisted of friction sliding bearing and rubber bearing. The bridge seismic performance has been evaluated on six different cases with six bearing models. The effects of the different arrangement of bearing on the deck superstructure displacements, the seismic damage at the bottom of the piers, movement track at the pier-s top and the total and strain energies absorbed by the structure are evaluated. In conclusion, the results provide sufficient evidence of the effectiveness on the use of seismic isolation on steel curved highway bridges.
Abstract: An important goal of parboiling is a decrease of rice broken percentage and at the beginning Selected paddy of variety of rice Tarom and soaked at three different temperatures 45 Cº, 65 Cº and 80 Cº orderly for 5 hours, 4 hours and 1.5 hours to moisture of 40 % and then in steaming stage to operate these action two steaming methods are selected steaming under pressure condition and steaming in atmosphere pressure and In the first method after exerting air, the steam pressure is increase to 1 Kg/Cm2 which is done in two different duration times of 2.5 and 5 minutes and in second method used of three times of 5,10 and 15 minutes and dry to 8% moisture and decreases of rice broken percentage at best condition in variety of Tarom of 37.2 % to 7.3 % and increases yield percentage at best condition in variety of Tarom of 69.4 % to 75.93 % and bran percentage decreased in variety of Tarom of 9.53 % to 2.2-3.2 % and this issue cause increases yield percentage in rice and use of This method is very significant for our country because broken percentage of rice in our country is 23-33 %.
Abstract: Multiplication algorithms have considerable effect on
processors performance. A new high-speed, low-power
multiplication algorithm has been presented using modified Dadda
tree structure. Three important modifications have been implemented
in inner product generation step, inner product reduction step and
final addition step. Optimized algorithms have to be used into basic
computation components, such as multiplication algorithms. In this
paper, we proposed a new algorithm to reduce power, delay, and
transistor count of a multiplication algorithm implemented using low
power modified counter. This work presents a novel design for
Dadda multiplication algorithms. The proposed multiplication
algorithm includes structured parts, which have important effect on
inner product reduction tree. In this paper, a 1.3V, 64-bit carry hybrid
adder is presented for fast, low voltage applications. The new 64-bit
adder uses a new circuit to implement the proposed carry hybrid
adder. The new adder using 80 nm CMOS technology has been
implemented on 700 MHz clock frequency. The proposed
multiplication algorithm has achieved 14 percent improvement in
transistor count, 13 percent reduction in delay and 12 percent
modification in power consumption in compared with conventional
designs.
Abstract: In this paper, a Web-based e-Training platform that is dedicated to multimodal breast imaging is presented. The assets of this platform are summarised in (i) the efficient representation of the curriculum flow that will permit efficient training; (ii) efficient tagging of multimodal content appropriate for the completion of realistic cases and (iii) ubiquitous accessibility and platform independence via a web-based approach.
Abstract: This study investigated the use of modified
atmosphere packaging (MAP) and different packaging to extend the
shelf life of Barbari flat bread. Three atmospheres including 70%CO2
and 30%N2, 50% CO2 and 50%N2 and a normal air as control were
used. The bread samples were packaged in three type pouches. The
shelf life was determined by appearance of mold and yeast (M +Y) in
Barbari bread samples stored at 25 ± 1°C and 38 ± 2% relative
humidity. The results showed that it is possible to prolong the shelf
life of Barbari bread from four days to about 21 days by using
modified atmosphere packaging with high carbon dioxide
concentration and high-barrier laminated and vacuum bags packages.
However, the hardness of samples kept in MAP increase significantly
by increase of carbon dioxide concentration. The correlation
coefficient (r) between headspace CO2 concentration and hardness
was 0.997, 0.997 and 0.599 for A, B and C packaging respectively.
High negative correlation coefficients were found between the crumb
moisture and the hardness values in various packaging. There were
significant negative correlation coefficients between sensory
parameters and hardness of texture.
Abstract: The fabrication of porous NiTi shape memory alloys (SMAs) from elemental powder compacts was conducted by selfpropagating high temperature synthesis (SHS). Effects of the preheating temperature and the chamber pressure on the combustion characteristics as well as the final morphology and the composition of products were studied. The samples with porosity between 56.4 and 59.0% under preheating temperature in the range of 200-300°C and Ar-gas chamber pressure of 138 and 201 kPa were obtained. The pore structures were found to be dissimilar only in the samples processed with different preheating temperature. The major phase in the porous product is NiTi with small amounts of secondary phases, NiTi2 and Ni4Ti3. The preheating temperature and the chamber pressure have very little effect on the phase constituent. While the combustion temperature of the sample was notably increased by increasing the preheating temperature, they were slightly changed by varying the chamber pressure.
Abstract: Study of the vibration cylindrical shells made of
a functionally gradient material (FGM) composed of stainless
steel and nickel is important. Material properties are graded in
the thickness direction of the shell according to volume
fraction power law distribution. The objective is to study the
natural frequencies, the influence of constituent volume
fractions and the effects of boundary conditions on the natural
frequencies of the FG cylindrical shell. The study is carried
out using third order shear deformation shell theory. The
governing equations of motion of FG cylindrical shells are
derived based on shear deformation theory. Results are
presented on the frequency characteristics, influence of
constituent volume fractions and the effects of clampedclamped
boundary conditions.
Abstract: In this paper an extensive verification of the extraction
method (published earlier) that consistently accounts for self-heating
and Early effect to accurately extract both base and thermal resistance
of bipolar junction transistors is presented. The method verification is
demonstrated on advanced RF SiGe HBTs were the extracted results
for the thermal resistance are compared with those from another
published method that ignores the effect of Early effect on internal
base-emitter voltage and the extracted results of the base resistance
are compared with those determined from noise measurements. A
self-consistency of our method in the extracted base resistance and
thermal resistance using compact model simulation results is also
carried out in order to study the level of accuracy of the method.
Abstract: Regarding previous research studies it was concluded
that thin-walled fiber-cement composites are able to conduct electric
current under specific conditions. This property is ensured by using
of various kinds of carbon materials. Though carbon fibers are less
conductive than metal fibers, composites with carbon fibers were
evaluated as better current conductors than the composites with metal
fibers. The level of electric conductivity is monitored by the means of
impedance measurement of designed samples. These composites
could be used for a range of applications such as heating of
trafficable surfaces or shielding of electro-magnetic fields.
The aim of the present research was to design an element with the
ability to monitor internal processes in building structures and
prevent them from collapsing. As a typical element for laboratory
testing there was chosen a concrete column, which was repeatedly
subjected to load by simple pressure with continual monitoring of
changes in electrical properties.
Abstract: In this paper, based on the work in [1], we further give
a general model for acquiring knowledge, which first focuses on the
research of how and when things involved in problems are made
then describes the goals, the energy and the time to give an optimum
model to decide how many related things are supposed to be involved
in. Finally, we acquire knowledge from this model in which there are
the attributes, actions and connections of the things involved at the
time when they are born and the time in their life. This model not
only improves AI theories, but also surely brings the effectiveness
and accuracy for AI system because systems are given more
knowledge when reasoning or computing is used to bring about
results.
Abstract: In this study, we illustrated the performance and
microbial community of single- and two-phase systems anaerobically
co-digesting cassava pulp and pig manure. The results showed that
the volatile solid reduction and biogas productivity of two-phase
CSTR were 66 ± 4% and 2000 ± 210 ml l-1 d-1, while those of singlephase
CSTR were 59 ± 1% and 1670 ± 60 ml l-1 d-1, respectively. Codigestion
in two-phase CSTR gave higher 12% solid degradation and
25% methane production than single-phase CSTR. Phylogenetic
analysis of 16S rDNA clone library revealed that the Bacteroidetes
were the most abundant group, followed by the Clostridia in singlephase
CSTR. In hydrolysis/acidification reactor of two-phase system,
the bacteria within the phylum Firmicutes, especially Clostridium,
Eubacteriaceae and Lactobacillus were the dominant phylogenetic
groups. Among the Archaea, Methanosaeta sp. was the exclusive
predominant in both digesters while the relative abundance of
Methanosaeta sp. and Methanospirillum hungatei differed between
the two systems.
Abstract: Greenhouse gases (GHG) emissions impose major
threat to global warming potential (GWP). Unfortunately
manufacturing sector is one of the major sources that contribute
towards the rapid increase in greenhouse gases (GHG) emissions. In
manufacturing sector electric power consumption is the major driver
that influences CO2 emission. Titanium alloys are widely utilized in
aerospace, automotive and petrochemical sectors because of their
high strength to weight ratio and corrosion resistance. Titanium
alloys are termed as difficult to cut materials because of their poor
machinability rating. The present study analyzes energy consumption
during cutting with reference to material removal rate (MRR).
Surface roughness was also measured in order to optimize energy
consumption.
Abstract: New biostimulator from wheat seeds which by its
chemical composition relates to fusicoccin is presented in this article.
New biostimulator could be used as powerful hormonal substance
that has ability to increase productivity and salt tolerance of
agricultural plants. Also on the basis of biostimulator we have
developed vegetative method for fast reproduction of perennial plants
as desert plant - Tamarix gracilis.
Abstract: Cities denote instantaneously a challenge and an
opportunity for climate change policy. Cities are the place where
most energy services are needed because urbanization is closely
linked to high population densities and concentration of economic
activities and production (Urban energy demand). Consequently, it is
critical to explain about the role of cities within the world-s energy
systems and its correlation with the climate change issue. With more
than half of the world-s population already living in urban areas, and
that percentage expected to rise to 75 per cent by 2050, it is clear that
the path to sustainable development must pass through cities. Cities
expanding in size and population pose increased challenges to the
environment, of which energy is part as a natural resource, and to the
quality of life. Nowadays, most cities have already understood the
importance of sustainability, both at their local scale as in terms of
their contribution to sustainability at higher geographical scales. It
requires the perception of a city as a complex and dynamic
ecosystem, an open system, or cluster of systems, where the energy
as well as the other natural resources is transformed to satisfy the
needs of the different urban activities. In fact, buildings and
transportation generally represent most of cities direct energy
demand, i.e., between 60 per cent and 80 per cent of the overall
consumption. Buildings, both residential and services are usually
influenced by the local physical and social conditions. In terms of
transport, the energy demand is also strongly linked with the specific
characteristics of a city (urban mobility).The concept of a “smart
city" builds on statistics as seven key axes of a city-s success in
moving towards common platform (brain nerve)of sustainable urban
energy systems.
With the aforesaid knowledge, the authors have suggested a frame
work to role of cities, as energy actors for smart city management.
The authors have discusses the potential elements needed for energy
in smart cities and also identified potential energy actions and
relevant barriers. Furthermore, three levels of city smartness in cities
actions to overcome market /institutional failures with a local
approach are distinguished. The authors have made an attempt to
conceive and implement concepts of city smartness by adopting the
city or local government as nerve center through an integrated
planning approach. Finally, concluding with recommendations for
the organization of the Smart Sustainable Cities for positive changes
of urban India.
Abstract: Optical 1x12 fused-taper-twisted polymer optical fiber (POF) couplers has been fabricated by a perform technique. Characterization of the coupler which proposed to be used in passive night vision application to tracking a blind sport area was reported. During the development process of fused-taper-twisted POF couplers was carried out, red LED fully utilized to be injected into the couplers to test the quality of fabricated couplers. Some characterization parameters, such as optical output power, POFs attenuation characteristics and power losses on the network were observed. The maximum output power efficiency of the coupler is about 40%, but it can be improved gradually through experience and practice.