Abstract: Comparison of electron- and photon-impact processes as a method for determination of photo-ionization cross sections is described, discussed and shown to have many attractive features.
Abstract: The stiffness of the workpiece is very important to reduce the errors in manufacturing process. The high stiffness of the workpiece can be achieved by optimal positioning of fixture elements in the fixture. The minimization of the sum of the nodal deflection normal to the surface is used as objective function in previous research. The deflection in other direction has been neglected. The 3-2-1 fixturing principle is not valid for metal sheets due to its flexible nature. We propose a new fixture layout optimization method N-3-2-1 for metal sheets that uses the strain energy of the finite elements. This method combines the genetic algorithm and finite element analysis. The objective function in this method is to minimize the sum of all the element strain energy. By using the concept of element strain energy, the deformations in all the directions have been considered. Strain energy and stiffness are inversely proportional to each other. So, lower the value of strain energy, higher will be the stiffness. Two different kinds of case studies are presented. The case studies are solved for both objective functions; element strain energy and nodal deflection. The result are compared to verify the propose method.
Abstract: This paper suggests using smartphones and community GPS application to make alerts more accurate and therefore positively influence the entire warning process. The paper is based on formerly published paper describing a Radio-HELP system. It summarizes existing methods and lists the advantages of proposed solution. The paper analyzes the advantages and disadvantages of each possible input, processing and output of the warning system.
Abstract: Severe damages may occur during the drilling of carbon fiber reinforced plastics (CFRP). In practice, this damage is limited by adding a backup support to the drilled parts. For some aeronautical parts with curvatures, backing up parts is a demanding process. In order to simplify the operation, this research studies the effect of using a configurable setup to support parts on the resulting quality of drilled holes. The test coupons referenced in this study are twenty four-plies unidirectional laminates made of carbon fibers and epoxy resin. Different signals were measured during the drilling process for these laminates, including the thrust force, the displacement and the acceleration. The processing of these signals demonstrated that the damage is due to the combination of two main factors: the spring-back of the thin part and the thrust force. The results found were confirmed for different feeds and speeds. When the distance between supports is increased, it is observed that the spring-back increases but the thrust force decreases. The study proves the feasibility of unsupported drilling of thin CFRP laminates without creating any observable damage.
Abstract: Managing a capital group is a complex and specific process. It creates special conditions for the introduction of team work organization of managers. The selection of a manager employment form is a problem which gets complicated in case of management teams. The considered possibilities are an employment-based and non-employment managerial contract, which can be based on a thorough action or on formulating definite expectations regarding the results of a manager’s work. The problem of selection between individual and collegiate settlement of managers’ work has been pointed out. The deliberations were based on the assumptions of chosen company management theories, including transactional cost, agency theory, nexus of contracts theory, stewardship theory and theories referring directly to management teams, i.e. Upper echelons theory.
Abstract: This paper describes an automated implementable
system for impulsive signals detection and recognition. The system
uses a Digital Signal Processing device for the detection and
identification process. Here the system analyses the signals in real
time in order to produce a particular response if needed. The system
analyses the signals in real time in order to produce a specific output
if needed. Detection is achieved through normalizing the inputs and
comparing the read signals to a dynamic threshold and thus avoiding
detections linked to loud or fluctuating environing noise.
Identification is done through neuronal network algorithms. As a
setup our system can receive signals to “learn” certain patterns.
Through “learning” the system can recognize signals faster, inducing
flexibility to new patterns similar to those known. Sound is captured
through a simple jack input, and could be changed for an enhanced
recording surface such as a wide-area recorder. Furthermore a
communication module can be added to the apparatus to send alerts
to another interface if needed.
Abstract: E-governance is an emerging and challenging initiative in developing countries. It is not only concerning the provision of services through the use ICT but rather entails building external interactions with citizen and businesses, enhancing democracy and trust of the political institutions of government. It embraces among other principles, openness, accountability and citizen engagement in public policy process. This study aims at finding users’ satisfaction with three chosen dimensions of e-governance, namely: openness, collaborative governance, and participation. These dimensions of e-governance are neither studied before in the context of Arab countries and nor explored earlier in relation to some demographics variables. A study of 900 users of e-government in United Arab Emirates (UAE) was undertaken to examine how gender, age, education, nationality, and employment affect their satisfaction with e-governance. Generally, satisfaction ratings vary significantly with these variables. However, the overall level of satisfaction with the three attributes was less favorable. Knowing the differences of citizen’s perceptions towards e-governance services would help policymakers in the design of effective e-governance strategy.
Abstract: This paper presents CMOS Current Mode Logic (CML) circuits for a high speed Digital to Analog Converter (DAC) using standard CMOS 65nm process. The CML circuits have the propagation delay advantage over its conventional CMOS counterparts due to smaller output voltage swing and tunable bias current. The CML circuits proposed in this paper can achieve a maximum propagation delay of only 9.3ps, which can satisfy the stringent requirement for the 5 GHz high speed DAC application. Another advantage for CML circuits is its dynamic symmetry characteristic resulting in a reduction of an additional inverter. Simulation results show that the proposed CML circuits can operate from 1.08V to 1.3V with temperature ranging from -40 to +120°C.
Abstract: In this work, we demonstrated vertical RRAM device fabricated at the sidewall of contact hole structures for possible future 3-D stacking integrations. The fabricated devices exhibit polarity dependent bipolar resistive switching with small operation voltage of less than 1V for both set and reset process. A good retention of memory window ~50 times is maintained after 1000s voltage bias.
Abstract: Silicon photonics has generated an increasing interest in recent years mainly for optical communications optical interconnects in microelectronic circuits or bio-sensing applications. The development of elementary passive and active components (including detectors and modulators), which are mainly fabricated on the silicon on insulator platform for CMOS-compatible fabrication, has reached such a performance level that the integration challenge of silicon photonics with microelectronic circuits should be addressed. Since crystalline silicon can only be grown from another silicon crystal, making it impossible to deposit in this state, the optical devices are typically limited to a single layer. An alternative approach is to integrate a photonic layer above the CMOS chip using back-end CMOS fabrication process. In this paper, various materials, including silicon nitride, amorphous silicon, and polycrystalline silicon, for this purpose are addressed.
Abstract: In this paper, the design of wide-swing constant transconductance (gm) bias circuit that generates bias voltage for low-noise amplifier (LNA) circuit design by using an off-chip resistor is demonstrated. The overall transconductance (Gm) generated by the constant gm bias circuit is important to maintain the overall gain and noise figure of the LNA circuit. Therefore, investigation is performed to study the variation in Gm with process, temperature and supply voltage (PVT). Temperature and supply voltage are swept from -10 °C to 85 °C and 1.425 V to 1.575 V respectively, while the process conditions are also varied to the extreme and the gm variation is eventually concluded at between -3 % to 7 %. With the slight variation in the gm value, through simulation, at worst condition of state SS, we are able to attain a conversion gain (S21) variation of -3.10 % and a noise figure (NF) variation of 18.71 %. The whole constant gm circuit draws approximately 100 µA from a 1.5V supply and is designed based on 0.13 µm CMOS process.
Abstract: Customer audits are generally used to ensure customer
that supplier is continuously able to meet his requirements while
supplying him required products and services. However, customer
audits can be considered as a very useful quality control tool for
suppliers as well. In our paper, we analyzed the process of customer
audits realized in Czech companies from both perspectives: a
supplier´s viewpoint and customer´s viewpoint. At the end, we tried
to emphasize some areas that should not be omitted during the audit
process.
Abstract: Ergonomics is a useful tool for creating a healthy and
safe workplace. The long-term action of harmful conditions on the
health of workers is the emergence of occupational disease, and the
firm-s increased compensation costs associated with these diseases,
but is also the loss of time needed for educating and including new
workers in the work process. The article deals with the link of
ergonomics to occupational diseases, factors which influence these
diseases. In the conclusion, a model is described to help reduce the
risk of selected occupational diseases using ergonomic principles and
knowledge.
Abstract: This study presents a new method for detecting the
cutting tool wear based on the measured cutting force signals using
the regression model and I-kaz method. The detection of tool wear
was done automatically using the in-house developed regression
model and 3D graphic presentation of I-kaz 3D coefficient during
machining process. The machining tests were carried out on a CNC
turning machine Colchester Master Tornado T4 in dry cutting
condition, and Kistler 9255B dynamometer was used to measure the
cutting force signals, which then stored and displayed in the DasyLab
software. The progression of the cutting tool flank wear land (VB)
was indicated by the amount of the cutting force generated. Later, the
I-kaz was used to analyze all the cutting force signals from beginning
of the cut until the rejection stage of the cutting tool. Results of the IKaz
analysis were represented by various characteristic of I-kaz 3D
coefficient and 3D graphic presentation. The I-kaz 3D coefficient
number decreases when the tool wear increases. This method can be
used for real time tool wear monitoring.
Abstract: The goal of this paper is to examine the effects of laser
radiation on the skin wound healing using infrared thermography as
non-invasive method for the monitoring of the skin temperature
changes during laser treatment. Thirty Wistar rats were used in this
study. A skin lesion was performed at the leg on all rats. The animals
were exposed to laser radiation (λ = 670 nm, P = 15 mW, DP = 16.31
mW/cm2) for 600 s. Thermal images of wound were acquired before
and after laser irradiation. The results have demonstrated that the
tissue temperature decreases from 35.5±0.50°C in the first treatment
day to 31.3±0.42°C after the third treatment day. This value is close
to the normal value of the skin temperature and indicates the end of
the skin repair process. In conclusion, the improvements in the
wound healing following exposure to laser radiation have been
revealed by infrared thermography.
Abstract: The software evolution control requires a deep
understanding of the changes and their impact on different system
heterogeneous artifacts. And an understanding of descriptive
knowledge of the developed software artifacts is a prerequisite
condition for the success of the evolutionary process.
The implementation of an evolutionary process is to make changes
more or less important to many heterogeneous software artifacts such
as source code, analysis and design models, unit testing, XML
deployment descriptors, user guides, and others. These changes can
be a source of degradation in functional, qualitative or behavioral
terms of modified software. Hence the need for a unified approach
for extraction and representation of different heterogeneous artifacts
in order to ensure a unified and detailed description of heterogeneous
software artifacts, exploitable by several software tools and allowing
to responsible for the evolution of carry out the reasoning change
concerned.
Abstract: In this paper we propose a new classification method for automatic sleep scoring using an artificial neural network based decision tree. It attempts to treat sleep scoring progress as a series of two-class problems and solves them with a decision tree made up of a group of neural network classifiers, each of which uses a special feature set and is aimed at only one specific sleep stage in order to maximize the classification effect. A single electroencephalogram (EEG) signal is used for our analysis rather than depending on multiple biological signals, which makes greatly simplifies the data acquisition process. Experimental results demonstrate that the average epoch by epoch agreement between the visual and the proposed method in separating 30s wakefulness+S1, REM, S2 and SWS epochs was 88.83%. This study shows that the proposed method performed well in all the four stages, and can effectively limit error propagation at the same time. It could, therefore, be an efficient method for automatic sleep scoring. Additionally, since it requires only a small volume of data it could be suited to pervasive applications.
Abstract: Jatropha curcas stem was analyzed for chemical
compositions: 19.11% pentosan, 42.99% alphacellulose and 24.11%
lignin based on dry weight of 100-g raw material. The condition to
fractionate cellulose, hemicellulose and lignin in J. curcas stem using
steam explosion was optimized. The procedure started from cutting J.
curcas stem into small pieces and soaked in water for overnight.
After that, they were steam exploded at 214 °C and 21 kg/cm2 for 5
min. The obtained hydrolysate contained 1.55 g/L ferulic acid which
after that was used as substrate for vanillin production by Aspergillus
niger and Pycnoporus cinnabarinus in one-step process. The
maximum 0.65 g/L of vanillin were obtained with the conversion rate
of 45.2% based on the initial ferulic acid.
Abstract: Today advertising is actively penetrating into many spheres of our lives. We cannot imagine the existence of a lot of economic activities without advertising. That mostly concerns trade and services. Everyone of us should look better into the everyday communication and carefully consider the amount and the quality of the information we receive as well as its influence on our behaviour. Special attention should be paid to the young generation. Theoretical and practical research has proved the ever growing influence of information (especially the one contained in advertising) on a society; on its economics, culture, religion, politics and even people-s private lives and behaviour. Children have plenty of free time and, therefore, see a lot of different advertising. Though education of children is in the hands of parents and schools, advertising makers and customers should think with responsibility about the selection of time and transmission channels of child targeted advertising. The purpose of the present paper is to investigate the influence of advertising upon consumer views and behaviour of children in different age groups. The present investigation has clarified the influence of advertising as a means of information on a certain group of society, which in the modern information society is the most vulnerable – children. In this paper we assess children-s perception and their understanding of advertising.
Abstract: This contribution was developed from a research
within the doctoral thesis. Its object was to create multimedia
materials for sport gymnastics. Consequently we surveyed the
influence of its practical application on the efficiency of schooling at
a university. We verified the prescribed hypothesis of the efficiency
of the teaching process using the method of single-factor experiment,
where the entrance independent variable was the change of system of
tuition and the outgoing dependent variable was the change of level
of acquired motor skills. The results confirmed the positive impact of
using multimedia materials on the efficiency of the teaching process.
Further, with the aid of questionnaires, we evaluated how the tested
subjects perceive the innovative methods in sport gymnastics. The
responses showed that the students rate the application of multimedia
materials very positively.