Abstract: In this paper a technique for increasing the
convergence rate of fractionally spaced channel equalizer is
proposed. Instead of symbol-spaced updating of the equalizer filter, a
mechanism has been devised to update the filter at a higher rate. This
ensures convergence of the equalizer filter at a higher rate and
therefore less time-consuming. The proposed technique has been
simulated and tested for two-ray modeled channels with various
delay spreads. These channels include minimum-phase and nonminimum-
phase channels. Simulation results suggest that that
proposed technique outperforms the conventional technique of
symbol-spaced updating of equalizer filter.
Abstract: Consumer electronics are pervasive. It is impossible to
imagine a household or office without DVD players, digital cameras,
printers, mobile phones, shavers, electrical toothbrushes, etc. All
these devices operate at different voltage levels ranging from 1.8 to
20 VDC, in the absence of universal standards. The voltages
available are however usually 120/230 VAC at 50/60 Hz. This
situation makes an individual electrical energy conversion system
necessary for each device. Such converters usually involve several
conversion stages and often operate with excessive losses and poor
reliability. The aim of the project presented in this paper is to design
and implement a multi-channel DC/DC converter system,
customizing the output voltage and current ratings according to the
requirements of the load. Distributed, multi-agent techniques will be
applied for the control of the DC/DC converters.
Abstract: Rarefied gas flows are often occurred in micro electro
mechanical systems and classical CFD could not precisely anticipate
the flow and thermal behavior due to the high Knudsen number.
Therefore, the heat transfer and the fluid dynamics characteristics of
rarefied gas flows in both a two-dimensional simple microchannel
and geometry similar to single Knudsen compressor have been
investigated with a goal of increasing performance of a actual
Knudsen compressor by using a particle simulation method. Thermal
transpiration and thermal creep, which are rarefied gas dynamic
phenomena, that cause movement of the flow from less to higher
temperature is generated by using two different longitude temperature
gradients (Linear, Step) along the walls of the flow microchannel. In
this study the influence of amount of temperature gradient and
governing pressure in various Knudsen numbers and length-to-height
ratios have been examined.
Abstract: A simple and dexterous in situ method was introduced to load CdS nanocrystals into organofunctionalized mesoporous, which used an ion-exchange method. The products were extensively characterized by combined spectroscopic methods. X- ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM) demonstrated both the maintenance of pore symmetry (space group p6mm) of SBA-15 and the presence of CdS nanocrystals with uniform sizes of about 6 - 8 nm inside the functionalized SBA-15 channels. These mesoporous silica-supported CdS composites showed room temperature photoluminescence properties with a blue shift, indicating the quantum size effect of nanocrystalline CdS.
Abstract: A microchannel with two inlets and two outlets was tested as a potential reactor to carry out two-phase catalytic phase transfer reaction with phase separation at the exit of the microchannel. The catalytic phase transfer reaction between benzyl chloride and sodium sulfide was chosen as a model reaction. The effect of operational time on the conversion was studied. By utilizing a multiphase parallel flow inside the microchannel reactor with the aid of a guideline structure, the catalytic phase reaction followed by phase separation could be ensured. The organic phase could be separated completely from one exit and part of the aqueous phase was separated purely and could be reused with slightly affecting the catalytic phase transfer reaction.
Abstract: Boon Rawd Brewery is a beer company based in
Thailand that has an exemplary image, both as a good employer and a
well-managed company with a strong record of social responsibility.
The most famous of the company’s products is Singha beer. To study
the company’s marketing strategy, a case study analysis was
conducted together with qualitative research methods. The study
analyzed the marketing strategy of Boon Rawd Brewery before the
liberalization of the liquor market in 2000. The company’s marketing
strategies consisted of the following: product line strategy, product
development strategy, block channel strategy, media strategy, trade
strategy, and consumer incentive strategy. Additionally, the company
employed marketing mix strategy based on the 4Ps: product, price,
promotion and place (of distribution).
Abstract: Cross sections of As radionuclides in the interaction of natGe with 14-30 MeV protons have been deduced by off-line y-ray spectroscopy to find optimal reaction channels leading to radiotracers for positron emission tomography. The experimental results were compared with the previous results and those estimated by the compound nucleus reaction model.
Abstract: The study was a case study analysis about Thai Asia
Pacific Brewery Company. The purpose was to analyze the
company’s marketing objective, marketing strategy at company level,
and marketing mix before liquor liberalization in 2000. Methods used
in this study were qualitative and descriptive research approach
which demonstrated the following results of the study demonstrated
as follows: (1) Marketing objective was to increase market share of
Heineken and Amtel, (2) the company’s marketing strategies were
brand building strategy and distribution strategy. Additionally, the
company also conducted marketing mix strategy as follows. Product
strategy: The company added more beer brands namely Amstel and
Tiger to provide additional choice to consumers, product and
marketing research, and product development. Price strategy: the
company had taken the following into consideration: cost,
competitor, market, economic situation and tax. Promotion strategy:
the company conducted sales promotion and advertising. Distribution
strategy: the company extended channels its channels of distribution
into food shops, pubs and various entertainment places. This strategy
benefited interested persons and people who were engaged in the beer
business.
Abstract: In this paper, an accurate theoretical analysis for the achievable average channel capacity (in the Shannon sense) per user of a hybrid cellular direct-sequence/fast frequency hopping code-division multiple-access (DS/FFH-CDMA) system operating in a Rayleigh fading environment is presented. The analysis covers the downlink operation and leads to the derivation of an exact mathematical expression between the normalized average channel capacity available to each system-s user, under simultaneous optimal power and rate adaptation and the system-s parameters, as the number of hops per bit, the processing gain applied, the number of users per cell and the received signal-tonoise power ratio over the signal bandwidth. Finally, numerical results are presented to illustrate the proposed mathematical analysis.
Abstract: The broadcast problem including the plan design is
considered. The data are inserted and numbered at predefined order
into customized size relations. The server ability to create a full,
regular Broadcast Plan (RBP) with single and multiple channels after
some data transformations is examined. The Regular Geometric
Algorithm (RGA) prepares a RBP and enables the users to catch their
items avoiding energy waste of their devices. Moreover, the
Grouping Dimensioning Algorithm (GDA) based on integrated
relations can guarantee the discrimination of services with a
minimum number of channels. This last property among the selfmonitoring,
self-organizing, can be offered by servers today
providing also channel availability and less energy consumption by
using smaller number of channels. Simulation results are provided.
Abstract: In an Orthogonal Frequency Division Multiplexing (OFDM) systems, the Peak to Average power Ratio (PAR) is high. The clipping signal scheme is a useful and simple method to reduce the PAR. However, it introduces additional noise that degrades the systems performance. We propose an oversampling scheme to deal with the received signal in order to reduce the clipping noise by using Finite Impulse Response (FIR) filter. Coefficients of filter are obtained by correlation function of the received signal and the oversampling information at receiver. The performance of the proposed technique is evaluated for frequency selective channel. Results show that the proposed scheme can mitigate the clipping noise significantly for OFDM systems and in order to maintain the system's capacity, the clipping ratio should be larger than 2.5.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: This paper presents an investigation of the power
penalties imposed by four-wave mixing (FWM) on G.652 (Single-
Mode Fiber - SMF), G.653 (Dispersion-Shifted Fiber - DSF), and
G.655 (Non-Zero Dispersion-Shifted Fiber - NZDSF) compliant
fibers, considering the DWDM grids suggested by the ITU-T
Recommendations G.692, and G.694.1, with uniform channel
spacing of 100, 50, 25, and 12.5 GHz. The mathematical/numerical
model assumes undepleted pumping, and shows very clearly the
deleterious effect of FWM on the performance of DWDM systems,
measured by the signal-to-noise ratio (SNR). The results make it
evident that non-uniform channel spacing is practically mandatory
for WDM systems based on DSF fibers.
Abstract: Available Bit Rate Service (ABR) is the lower priority
service and the better service for the transmission of data. On wireline
ATM networks ABR source is always getting the feedback from
switches about increase or decrease of bandwidth according to the
changing network conditions and minimum bandwidth is guaranteed.
In wireless networks guaranteeing the minimum bandwidth is really a
challenging task as the source is always in mobile and traveling from
one cell to another cell. Re establishment of virtual circuits from start
to end every time causes the delay in transmission. In our proposed
solution we proposed the mechanism to provide more available
bandwidth to the ABR source by re-usage of part of old Virtual
Channels and establishing the new ones. We want the ABR source to
transmit the data continuously (non-stop) inorderto avoid the delay.
In worst case scenario at least minimum bandwidth is to be allocated.
In order to keep the data flow continuously, priority is given to the
handoff ABR call against new ABR call.
Abstract: A series of tests on cold-formed steel (CFS) wall plate system subjected to uplift force at the mid span of the wall plate is presented. The aim of the study was to study the behaviour and identify the modes of failure of CFS wall plate system. Two parameters were considered in these studies: 1) different dimension of U-bracket at the supports and 2) different sizes of lipped C-channel. The lipped C-channels used were C07508, C07512 and C10012. The dimensions of the leg of U-bracket were 50x35 mm and 50x60 mm respectively, where 25 mm clearance was provided to the connections for specimens with clearance. Results show that specimens with and without clearance experienced the same mode of failure. Failure began with the yielding of the connectors followed by distortional buckling of the wall plate. However, when C075 sections were used as wall plate, the system behaved differently. There was a large deformation in the wall plate and failure began in the distortional buckling of the wall plate followed by bearing of the connecting plates at the supports (U-bracket). The ultimate strength of the system also decreased dramatically when C075 sections were used.
Abstract: A numerical method is developed for simulating
the motion of particles with arbitrary shapes in an effectively
infinite or bounded viscous flow. The particle translational and
angular motions are numerically investigated using a fluid-structure
interaction (FSI) method based on the Arbitrary-Lagrangian-Eulerian
(ALE) approach and the dynamic mesh method (smoothing and
remeshing) in FLUENT ( ANSYS Inc., USA). Also, the effects of
arbitrary shapes on the dynamics are studied using the FSI method
which could be applied to the motions and deformations of a single
blood cell and multiple blood cells, and the primary thrombogenesis
caused by platelet aggregation. It is expected that, combined with a
sophisticated large-scale computational technique, the simulation
method will be useful for understanding the overall properties of blood
flow from blood cellular level (microscopic) to the resulting
rheological properties of blood as a mass (macroscopic).
Abstract: The direct implementation of interleaver functions
in WiMAX is not hardware efficient due to presence of complex
functions. Also the conventional method i.e. using memories for
storing the permutation tables is silicon consuming. This work
presents a 2-D transformation for WiMAX channel interleaver
functions which reduces the overall hardware complexity to
compute the interleaver addresses on the fly. A fully reconfigurable
architecture for address generation in WiMAX
channel interleaver is presented, which consume 1.1 k-gates in
total. It can be configured for any block size and any modulation
scheme in WiMAX. The presented architecture can run at a
frequency of 200 MHz, thus fully supporting high bandwidth
requirements for WiMAX.
Abstract: Dedicated Short Range Communication (DSRC) is a
key enabling technology for the next generation of
communication-based safety applications. One of the important
problems for DSRC deployment is maintaining high performance
under heavy channel load. Many studies focus on congestion control
mechanisms for simulating hundreds of physical radios deployed on
vehicles. The U.S. department of transportation-s (DOT) Intelligent
Transportation Systems (ITS) division has a plan to chosen prototype
on-board devices capable of transmitting basic “Here I am" safety
messages to other vehicles. The devices will be used in an IntelliDrive
safety pilot deployment of up to 3,000 vehicles. It is hard to log the
information of 3,000 vehicles. In this paper we present the designs and
issues related to the DSRC Radio Testbed under heavy channel load.
The details not only include the architecture of DSRC Radio Testbed,
but also describe how the Radio Interfere System is used to help for
emulating the congestion radio environment.
Abstract: A new design of a planar passive T-micromixer with fin-shaped baffles in the mixing channel is presented. The mixing efficiency and the level of pressure loss in the channel have been investigated by numerical simulations in the range of Reynolds number (Re) 1 to 50. A Mixing index (Mi) has been defined to quantify the mixing efficiency, which results over 85% at both ends of the Re range, what demonstrates the micromixer can enhance mixing using the mechanisms of diffusion (lower Re) and convection (higher Re). Three geometric dimensions: radius of baffle, baffles pitch and height of the channel define the design parameters, and the mixing index and pressure loss are the performance parameters used to optimize the micromixer geometry with a multi-criteria optimization method. The Pareto front of designs with the optimum trade-offs, maximum mixing index with minimum pressure loss, is obtained. Experiments for qualitative and quantitative validation have been implemented.
Abstract: In this paper we present a new multichannel high
voltage driver box to connect up to six MOEMS mirror devices to it that have resonant and also quasistatically driven actuating electrodes. It is possible to drive all resonant axes synchronously
while the amplitude of them can individually be controlled by separate microcontrollers that also operate the quasistatic axes.
Circuit simulations are compared with the measurements done on the
real system and also show the robust driving performance of a
MOEMS mirror.