Abstract: A comprehensive discussion of feasible strategies for sustainable energy supply is urgently needed to achieve a turnaround of the current energy situation. The necessary fundamentals required for the development of a long term energy vision are lacking to a great extent due to the absence of reasonable long term scenarios that fulfill the requirements of climate protection and sustainable energy use. The contribution of the study is based on a search for sustainable energy paths in the long run for Austria. The analysis makes use of secondary data predominantly. The measures developed to avoid CO2 emissions and other ecological risk factors vary to a great extent among all economic sectors. This is shown by the calculation of CO2 cost of abatement curves. In this study it is demonstrated that the most effective technical measures with the lowest CO2 abatement costs yield solutions to the current energy problems. Various scenarios are presented concerning the question how the technological and environmental options for a sustainable energy system for Austria could look like in the long run. It is shown how sustainable energy can be supplied even with today-s technological knowledge and options available. The scenarios developed include an evaluation of the economic costs and ecological impacts. The results are not only applicable to Austria but demonstrate feasible and cost efficient ways towards a sustainable future.
Abstract: Optical flow is a research topic of interest for many
years. It has, until recently, been largely inapplicable to real-time
applications due to its computationally expensive nature. This paper
presents a new reliable flow technique which is combined with a
motion detection algorithm, from stationary camera image streams,
to allow flow-based analyses of moving entities, such as rigidity, in
real-time. The combination of the optical flow analysis with motion
detection technique greatly reduces the expensive computation of
flow vectors as compared with standard approaches, rendering the
method to be applicable in real-time implementation. This paper
describes also the hardware implementation of a proposed pipelined
system to estimate the flow vectors from image sequences in real
time. This design can process 768 x 576 images at a very high frame
rate that reaches to 156 fps in a single low cost FPGA chip, which is
adequate for most real-time vision applications.
Abstract: In this paper a new approach to face recognition is presented that achieves double dimension reduction making the system computationally efficient with better recognition results. In pattern recognition techniques, discriminative information of image increases with increase in resolution to a certain extent, consequently face recognition results improve with increase in face image resolution and levels off when arriving at a certain resolution level. In the proposed model of face recognition, first image decimation algorithm is applied on face image for dimension reduction to a certain resolution level which provides best recognition results. Due to better computational speed and feature extraction potential of Discrete Cosine Transform (DCT) it is applied on face image. A subset of coefficients of DCT from low to mid frequencies that represent the face adequately and provides best recognition results is retained. A trade of between decimation factor, number of DCT coefficients retained and recognition rate with minimum computation is obtained. Preprocessing of the image is carried out to increase its robustness against variations in poses and illumination level. This new model has been tested on different databases which include ORL database, Yale database and a color database. The proposed technique has performed much better compared to other techniques. The significance of the model is two fold: (1) dimension reduction up to an effective and suitable face image resolution (2) appropriate DCT coefficients are retained to achieve best recognition results with varying image poses, intensity and illumination level.
Abstract: The frequency dependence of the phase field
model(PFM) is studied. A simple PFM is proposed, and is tested in a
laminar boundary layer. The Blasius-s laminar boundary layer
solution on a flat plate is used for the flow pattern, and several
frequencies are imposed on the PFM, and the decay times of the
interfaces are obtained. The computations were conducted for three
cases: 1) no-flow, and 2) a half ball on the laminar boundary layer, 3) a
line of mass sources in the laminar boundary layer. The computations
show the decay time becomes shorter as the frequency goes larger, and
also show that it is sensitive to both background disturbances and
surface tension parameters. It is concluded that the proposed simple
PFM can describe the properties of decay process, and could give the
fundamentals for the decay of the interface in turbulent flows.
Abstract: The rapid development of manufacturing and information systems has caused significant changes in manufacturing environments in recent decades. Mass production has given way to flexible manufacturing systems, in which an important characteristic is customized or "on demand" production. In this scenario, the seamless and without gaps information flow becomes a key factor for success of enterprises. In this paper we present a framework to support the mapping of features into machining workingsteps compliant with the ISO 14649 standard (known as STEP-NC). The system determines how the features can be made with the available manufacturing resources. Examples of the mapping method are presented for features such as a pocket with a general surface.
Abstract: Human perceives color in categories, which may be
identified using color name such as red, blue, etc. The categorization
is unique for each human being. However despite the individual
differences, the categorization is shared among members in society.
This allows communication among them, especially when using
color name. Sociable robot, to live coexist with human and become
part of human society, must also have the shared color
categorization, which can be achieved through learning. Many
works have been done to enable computer, as brain of robot, to learn
color categorization. Most of them rely on modeling of human color
perception and mathematical complexities. Differently, in this work,
the computer learns color categorization through interaction with
humans. This work aims at developing the innate ability of the
computer to learn the human-like color categorization. It focuses on
the representation of color categorization and how it is built and
developed without much mathematical complexity.
Abstract: This paper describes a segmentation algorithm based
on the cooperation of an optical flow estimation method with edge
detection and region growing procedures.
The proposed method has been developed as a pre-processing
stage to be used in methodologies and tools for video/image indexing
and retrieval by content. The addressed problem consists in
extracting whole objects from background for producing images of
single complete objects from videos or photos. The extracted images
are used for calculating the object visual features necessary for both
indexing and retrieval processes.
The first task of the algorithm exploits the cues from motion
analysis for moving area detection. Objects and background are then
refined using respectively edge detection and region growing
procedures. These tasks are iteratively performed until objects and
background are completely resolved.
The developed method has been applied to a variety of indoor and
outdoor scenes where objects of different type and shape are
represented on variously textured background.
Abstract: In this era of competitiveness, there is a growing need for supply chains also to become competitive enough to handle pressures like varying customer’s expectations, low cost high quality products to be delivered at the minimum time and the most important is throat cutting competition at world wide scale. In the recent years, supply chain competitiveness has been, therefore, accepted as one of the most important philosophies in the supply chain literature. Various researchers and practitioners have tried to identify and implement strategies in supply chains which can bring competitiveness in the supply chains i.e. supply chain competitiveness. The purpose of this paper is to suggest select strategies for supply chain competitiveness in the Indian manufacturing sector using an integrated approach of literature review and exploratory interviews with eminent professionals from the supply chain area in various industries, academia and research. The aim of the paper is to highlight the important area of competitiveness in the supply chain and to suggest recommendations to the industry and managers of manufacturing sector.
Abstract: Most of the losses in a power system relate to
the distribution sector which always has been considered.
From the important factors which contribute to increase losses
in the distribution system is the existence of radioactive flows.
The most common way to compensate the radioactive power
in the system is the power to use parallel capacitors. In
addition to reducing the losses, the advantages of capacitor
placement are the reduction of the losses in the release peak of
network capacity and improving the voltage profile. The point
which should be considered in capacitor placement is the
optimal placement and specification of the amount of the
capacitor in order to maximize the advantages of capacitor
placement.
In this paper, a new technique has been offered for the
placement and the specification of the amount of the constant
capacitors in the radius distribution network on the basis of
Genetic Algorithm (GA). The existing optimal methods for
capacitor placement are mostly including those which reduce
the losses and voltage profile simultaneously. But the
retaliation cost and load changes have not been considered as
influential UN the target function .In this article, a holistic
approach has been considered for the optimal response to this
problem which includes all the parameters in the distribution
network: The price of the phase voltage and load changes. So,
a vast inquiry is required for all the possible responses. So, in
this article, we use Genetic Algorithm (GA) as the most
powerful method for optimal inquiry.
Abstract: In this paper, we have proposed a novel FinFET with
extended body under the poly gate, which is called EB-FinFET, and
its characteristic is demonstrated by using three-dimensional (3-D)
numerical simulation. We have analyzed and compared it with
conventional FinFET. The extended body height dependence on the
drain induced barrier lowering (DIBL) and subthreshold swing (S.S)
have been also investigated. According to the 3-D numerical
simulation, the proposed structure has a firm structure, an acceptable
short channel effect (SCE), a reduced series resistance, an increased
on state drain current (I
on) and a large normalized I
DS. Furthermore,
the structure can also improve corner effect and reduce self-heating
effect due to the extended body. Our results show that the EBFinFET
is excellent for nanoscale device.
Abstract: In this paper we propose a new traffic simulation
package, TDMSim, which supports both macroscopic and
microscopic simulation on free-flowing and regulated traffic systems.
Both simulators are based on travel demands, which specify the
numbers of vehicles departing from origins to arrive at different
destinations. The microscopic simulator implements the carfollowing
model given the pre-defined routes of the vehicles but also
supports the rerouting of vehicles. We also propose a macroscopic
simulator which is built in integration with the microscopic simulator
to allow the simulation to be scaled for larger networks without
sacrificing the precision achievable through the microscopic
simulator. The macroscopic simulator also enables the reuse of
previous simulation results when simulating traffic on the same
networks at later time. Validations have been conducted to show the
correctness of both simulators.
Abstract: Linear stochastic estimation and quadratic stochastic
estimation techniques were applied to estimate the entire velocity
flow-field of an open cavity with a length to depth ratio of 2. The
estimations were done through the use of instantaneous velocity
magnitude as estimators. These measurements were obtained by
Particle Image Velocimetry. The predicted flow was compared
against the original flow-field in terms of the Reynolds stresses and
turbulent kinetic energy. Quadratic stochastic estimation proved to be
more superior than linear stochastic estimation in resolving the shear
layer flow. When the velocity fluctuations were scaled up in the
quadratic estimate, both the time-averaged quantities and the
instantaneous cavity flow can be predicted to a rather accurate extent.
Abstract: The aim of this study was to compare the
sensitometric properties of commonly used radiographic films
processed with chemical solutions in different workload hospitals.
The effect of different processing conditions on induced densities on
radiologic films was investigated. Two accessible double emulsions
Fuji and Kodak films were exposed with 11-step wedge and
processed with Champion and CPAC processing solutions. The
mentioned films provided in both workloads centers, high and low.
Our findings displays that the speed and contrast of Kodak filmscreen
in both work load (high and low) is higher than Fuji filmscreen
for both processing solutions. However there was significant
differences in films contrast for both workloads when CPAC solution
had been used (p=0.000 and 0.028). The results showed base plus
fog density for Kodak film was lower than Fuji. Generally Champion
processing solution caused more speed and contrast for investigated
films in different conditions and there was significant differences in
95% confidence level between two used processing solutions
(p=0.01). Low base plus fog density for Kodak films provide more
visibility and accuracy and higher contrast results in using lower
exposure factors to obtain better quality in resulting radiographs. In
this study we found an economic advantages since Champion
solution and Kodak film are used while it makes lower patient dose.
Thus, in a radiologic facility any change in film processor/processing
cycle or chemistry should be carefully investigated before
radiological procedures of patients are acquired.
Abstract: Two commercial proteases from Bacillus
licheniformis (Alcalase 2.4 L FG and Alcalase 2.5 L, Type DX) were
screened for the production of Z-Ala-Phe-NH2 in batch reaction.
Alcalase 2.4 L FG was the most efficient enzyme for the C-terminal
amidation of Z-Ala-Phe-OMe using ammonium carbamate as
ammonium source. Immobilization of protease has been achieved by
the sol-gel method, using dimethyldimethoxysilane (DMDMOS) and
tetramethoxysilane (TMOS) as precursors (unpublished results). In
batch production, about 95% of Z-Ala-Phe-NH2 was obtained at
30°C after 24 hours of incubation. Reproducibility of different
batches of commercial Alcalase 2.4 L FG preparations was also
investigated by evaluating the amidation activity and the entrapment
yields in the case of immobilization. A packed-bed reactor (0.68 cm
ID, 15.0 cm long) was operated successfully for the continuous
synthesis of peptide amides. The immobilized enzyme retained the
initial activity over 10 cycles of repeated use in continuous reactor at
ambient temperature. At 0.75 mL/min flow rate of the substrate
mixture, the total conversion of Z-Ala-Phe-OMe was achieved after 5
hours of substrate recycling. The product contained about 90%
peptide amide and 10% hydrolysis byproduct.
Abstract: A boundary layer wind tunnel facility has been
adopted in order to conduct experimental measurements of the flow field around a model of the Panorama Giustinelli Building, Trieste
(Italy). Information on the main flow structures has been obtained by means of flow visualization techniques and has been compared to the
numerical predictions of the vortical structures spread on top of the roof, in order to investigate the optimal positioning for a vertical-axis
wind energy conversion system, registering a good agreement between experimental measurements and numerical predictions.
Abstract: The acidity of different raw Jordanian clays
containing zeolite, bentonite, red and white kaolinite and diatomite
was characterized by means of temperature programmed desorption
(TPD) of ammonia, conversion of 2-methyl-3-butyn-2-ol (MBOH),
FTIR and BET-measurements. FTIR spectra proved presence of
silanol and bridged hydroxyls on the clay surface. The number of
acidic sites was calculated from experimental TPD-profiles. We
observed the decrease of surface acidity correlates with the decrease
of Si/Al ratio except for diatomite. On the TPD-plot for zeolite two
maxima were registered due to different strength of surface acidic
sites. Values of MBOH conversion, product yields and selectivity
were calculated for the catalysis on Jordanian clays. We obtained that
all clay samples are able to convert MBOH into a major product
which is 3-methyl-3-buten-1-yne (MBYNE) catalyzed by acid
surface sites with the selectivity close to 70%. There was found a
correlation between MBOH conversion and acidity of clays
determined by TPD-NH3, i.e. the higher the acidity the higher the
conversion of MBOH. However, diatomite provided the lowest
conversion of MBOH as result of poor polarization of silanol groups.
Comparison of surface areas and conversions revealed the highest
density of active sites for red kaolinite and the lowest for zeolite and
diatomite.
Abstract: Chaiyaphum Starch Co. Ltd. is one of many starch
manufacturers that has introduced machinery to aid in manufacturing.
Even though machinery has replaced many elements and is now a
significant part in manufacturing processes, problems that must be
solved with respect to current process flow to increase efficiency still
exist. The paper-s aim is to increase productivity while maintaining
desired quality of starch, by redesigning the flipping machine-s
mechanical control system which has grossly low functional lifetime.
Such problems stem from the mechanical control system-s bearings,
as fluids and humidity can access into said bearing directly, in
tandem with vibrations from the machine-s function itself. The wheel
which is used to sense starch thickness occasionally falls from its
shaft, due to high speed rotation during operation, while the shaft
may bend from impact when processing dried bread. Redesigning its
mechanical control system has increased its efficiency, allowing
quality thickness measurement while increasing functional lifetime
an additional 62 days.
Abstract: Given a parallel program to be executed on a heterogeneous
computing system, the overall execution time of the program
is determined by a schedule. In this paper, we analyze the worst-case
performance of the list scheduling algorithm for scheduling tasks
of a parallel program in a mixed-machine heterogeneous computing
system such that the total execution time of the program is minimized.
We prove tight lower and upper bounds for the worst-case
performance ratio of the list scheduling algorithm. We also examine
the average-case performance of the list scheduling algorithm. Our
experimental data reveal that the average-case performance of the list
scheduling algorithm is much better than the worst-case performance
and is very close to optimal, except for large systems with large
heterogeneity. Thus, the list scheduling algorithm is very useful in
real applications.
Abstract: Sophorolipids (SLs) production by the yeast Candida
bombicola was studied in batch shake flasks using synthetic dairy
wastewaters (SDWW) with or without any added external carbon and
nitrogen sources. A maximum SLs production of 38.76 g/l was
observed with the SDWW supplemented with low cost substrate of
sugarcane molasses at 50 g/l and soybean oil at 50 g/l. When the
SDWW was supplemented with more costly glucose, yeast extract,
urea and soybean oil, the production, however, got lowered to only
29.49 g/l, but with a maximum biomass production of 17.38 g/l
together with a complete utilization of the carbon sources.
Abstract: This paper presents an equivalent circuit model based on piecewise linear parallel branches (PLPB) to study solar cell modules which are partially shaded. The PLPB model can easily be used in circuit simulation software such as the ElectroMagnetic Transients Program (EMTP). This PLPB model allows the user to simulate several different configurations of solar cells, the influence of partial shadowing on a single or multiple cells, the influence of the number of solar cells protected by a bypass diode and the effect of the cell connection configuration on partial shadowing.