Abstract: In this paper the influence of heterogeneous traffic on
the temporal variation of ambient PM10, PM2.5 and PM1
concentrations at a busy arterial route (Sardar Patel Road) in the
Chennai city has been analyzed. The hourly PM concentration, traffic
counts and average speed of the vehicles have been monitored at the
study site for one week (19th-25th January 2009). Results indicated
that the concentrations of coarse (PM10) and fine PM (PM2.5 and
PM1) concentrations at SP road are having similar trend during peak
and non-peak hours, irrespective of the days. The PM concentrations
showed daily two peaks corresponding to morning (8 to 10 am) and
evening (7 to 9 pm) peak hour traffic flow. The PM10 concentration is
dominated by fine particles (53% of PM2.5 and 45% of PM1). The
high PM2.5/PM10 ratio indicates that the majority of PM10 particles
originate from re-suspension of road dust. The analysis of traffic flow
at the study site showed that 2W, 3W and 4W are having similar
diurnal trend as PM concentrations. This confirms that the 2W, 3W
and 4W are the main emission source contributing to ambient PM
concentration at SP road. The speed measurement at SP road showed
that the average speed of 2W, 3W, 4W, LCV and HCV are 38, 40,
38, 40 and 38 km/hr and 43, 41, 42, 40 and 41 km/hr respectively for
the weekdays and weekdays.
Abstract: Ascorbic acid (AA), commonly known as vitamin C, is essential for normal functioning of the body and maintenance of metabolic integrity. Among its various roles are as an antioxidant, a cofactor in collagen formation and other reactions, as well as reducing physical stress and maintenance of the immune system. Recent collaborative research between the Australian Defence Science and Technology Organisation (DSTO) in Scottsdale, Tasmania and RMIT University has sought to overcome the problems arising from the inherent instability of ascorbic acid during processing and storage of foods. The recent work has demonstrated the potential of microencapsulation by spray drying as a means to enhance retention. The purpose of this current study has been focused upon the influence of spray drying conditions on the properties of encapsulated ascorbic acid. The process was carried out according to a central composite design. Independent variables were: inlet temperature (80-120° C) and feed flow rate (7-14 mL/minute). Process yield, ascorbic acid loss, moisture content, water activity and particle size distribution were analysed as responses. The results have demonstrated the potential of microencapsulation by spray drying as a means to enhance retention. Vitamin retention, moisture content, water activity and process yield were influenced positively by inlet air temperature and negatively by feed flow rate.
Abstract: The conventional assessment of human semen is a
highly subjective assessment, with considerable intra- and interlaboratory
variability. Computer-Assisted Sperm Analysis (CASA)
systems provide a rapid and automated assessment of the sperm
characteristics, together with improved standardization and quality
control. However, the outcome of CASA systems is sensitive to the
method of experimentation. While conventional CASA systems use
digital microscopes with phase-contrast accessories, producing
higher contrast images, we have used raw semen samples (no
staining materials) and a regular light microscope, with a digital
camera directly attached to its eyepiece, to insure cost benefits and
simple assembling of the system. However, since the accurate finding
of sperms in the semen image is the first step in the examination and
analysis of the semen, any error in this step can affect the outcome of
the analysis. This article introduces and explains an algorithm for
finding sperms in low contrast images: First, an image enhancement
algorithm is applied to remove extra particles from the image. Then,
the foreground particles (including sperms and round cells) are
segmented form the background. Finally, based on certain features
and criteria, sperms are separated from other cells.
Abstract: Particle damping is a technique to reduce the
structural vibrations by means of placing small metallic particles
inside a cavity that is attached to the structure at location of high
vibration amplitudes. In this paper, we have presented an analytical
model to simulate the particle damping of two dimensional transient
vibrations in structure operating under high centrifugal loads. The
simulation results show that this technique remains effective as long
as the ratio of the dynamic acceleration of the structure to the applied
centrifugal load is more than 0.1. Particle damping increases with the
increase of particle to structure mass ratio. However, unlike to the
case of particle damping in the absence of centrifugal loads where
the damping efficiency strongly depends upon the size of the cavity,
here this dependence becomes very weak. Despite the simplicity of
the model, the simulation results are considerably in good agreement
with the very scarce experimental data available in the literature for
particle damping under centrifugal loads.
Abstract: Calcium oxide (CaO) as carbon dioxide (CO2)
adsorbent at the elevated temperature has been very well-received
thus far. The CaO can be synthesized from natural calcium carbonate
(CaCO3) sources through the reversible calcination-carbonation
process. In the study, cockle shell has been selected as CaO
precursors. The objectives of the study are to investigate the
performance of calcination and carbonation with respect to different
temperature, heating rate, particle size and the duration time. Overall,
better performance is shown at the calcination temperature of 850oC
for 40 minutes, heating rate of 20oC/min, particle size of < 0.125mm
and the carbonation temperature is at 650oC. The synthesized
materials have been characterized by nitrogen physisorption and
surface morphology analysis. The effectiveness of the synthesized
cockle shell in capturing CO2 (0.72 kg CO2/kg adsorbent) which is
comparable to the commercialized adsorbent (0.60 kg CO2/kg
adsorbent) makes them as the most promising materials for CO2
capture.
Abstract: An explicit axisymmetrical FE methodology is
developed here to study the particle temperature arising in WC-Co
particle on an AISI 1045 steel substrate. Parameters of constitutive
Johnson-cook model were used for simulation. The results show that
particle velocity and kinetic energy have important role in
temperature arising of particles.
Abstract: Enzymatic hydrolysis is one of the major steps involved in the conversion from sugarcane bagasse to yield ethanol. This process offers potential for yields and selectivity higher, lower energy costs and milder operating conditions than chemical processes. However, the presence of some factors such as lignin content, crystallinity degree of the cellulose, and particle sizes, limits the digestibility of the cellulose present in the lignocellulosic biomasses. Pretreatment aims to improve the access of the enzyme to the substrate. In this study sugarcane bagasse was submitted chemical pretreatment that consisted of two consecutive steps, the first with dilute sulfuric acid (1 % (v/v) H2SO4), and the second with alkaline solutions with different concentrations of NaOH (1, 2, 3 and 4 % (w/v)). Thermal Analysis (TG/ DTG and DTA) was used to evaluate hemicellulose, cellulose and lignin contents in the samples. Scanning Electron Microscopy (SEM) was used to evaluate the morphological structures of the in natura and chemically treated samples. Results showed that pretreatments were effective in chemical degradation of lignocellulosic materials of the samples, and also was possible to observe the morphological changes occurring in the biomasses after pretreatments.
Abstract: This paper presents the use of three-dimensional finite
elements coupled with infinite elements to investigate the ground
vibrations at the surface in terms of the peak particle velocity (PPV)
due to construction of the first bore of the Dublin Port Tunnel. This
situation is analysed using a commercially available general-purpose
finite element package ABAQUS. A series of parametric studies is
carried out to examine the sensitivity of the predicted vibrations to
variations in the various input parameters required by finite element
method, including the stiffness and the damping of ground. The
results of this study show that stiffness has a more significant effect
on the PPV rather than the damping of the ground.
Abstract: In deregulated operating regime power system security is an issue that needs due thoughtfulness from researchers in the horizon of unbundling of generation and transmission. Electric power systems are exposed to various contingencies. Network contingencies often contribute to overloading of branches, violation of voltages and also leading to problems of security/stability. To maintain the security of the systems, it is desirable to estimate the effect of contingencies and pertinent control measurement can be taken on to improve the system security. This paper presents the application of particle swarm optimization algorithm to find the optimal location of multi type FACTS devices in a power system in order to eliminate or alleviate the line over loads. The optimizations are performed on the parameters, namely the location of the devices, their types, their settings and installation cost of FACTS devices for single and multiple contingencies. TCSC, SVC and UPFC are considered and modeled for steady state analysis. The selection of UPFC and TCSC suitable location uses the criteria on the basis of improved system security. The effectiveness of the proposed method is tested for IEEE 6 bus and IEEE 30 bus test systems.
Abstract: This paper describes a rapid prototyping (RP)
technology for forming a hydroxyapatite (HA) bone scaffold model.
The HA powder and a silica sol are mixed into bioceramic slurry form
under a suitable viscosity. The HA particles are embedded in the
solidified silica matrix to form green parts via a wide range of process
parameters after processing by selective laser sintering (SLS). The
results indicate that the proposed process was possible to fabricate
multilayers and hollow shell structure with brittle property but
sufficient integrity for handling prior to post-processing. The
fabricated bone scaffold models had a surface finish of 25
Abstract: Particle swarm optimization (PSO) technique is applied to design the water distribution pipeline network. A simulation-optimization model is formulated with the objective of minimizing cost and is applied to a benchmark water distribution system optimization problem. The benchmark problem taken for the application of PSO technique to optimize the pipe size of the water distribution network is New York City water supply system problem. The results from the analysis infer that PSO is a potential alternative optimization technique when compared to other heuristic techniques for optimal sizing of water distribution systems.
Abstract: Diesel Engines emit complex mixtures of inorganic
and organic compounds in the form of both solid and vapour phase
particles. Most of the particulates released are ultrafine nanoparticles
which are detrimental to human health and can easily enter the body
by respiration. The emissions standards on particulate matter release
from diesel engines are constantly upgraded within the European
Union and with future regulations based on the particles numbers
released instead of merely mass, the need for effective aftertreatment
devices will increase. Standard particulate filters in the form of wall
flow filters can have problems with high soot accumulation,
producing a large exhaust backpressure. A potential solution would
be to combine the standard filter with a flow through filter to reduce
the load on the wall flow filter. In this paper soot particle trapping has
been simulated in different continuous flow filters of monolithic
structure including the use of promoters, at laminar flow conditions.
An Euler Lagrange model, the discrete phase model in Ansys used
with user defined functions for forces acting on particles. A method
to quickly screen trapping of 5 nm and 10 nm particles in different
catalysts designs with tracers was also developed.
Simulations of square duct monoliths with promoters show that the
strength of the vortices produced are not enough to give a high
amount of particle deposition on the catalyst walls. The smallest
particles in the simulations, 5 and 10 nm particles were trapped to a
higher extent, than larger particles up to 1000 nm, in all studied
geometries with the predominant deposition mechanism being
Brownian diffusion. The comparison of the different filters designed
with a wall flow filter does show that the options for altering a design
of a flow through filter, without imposing a too large pressure drop
penalty are good.
Abstract: This paper presents a multi-objective formulation for
optimal siting and sizing of distributed generation (DG) resources in
distribution systems in order to minimize the cost of power losses
and energy not supplied. The implemented technique is based on
particle swarm optimization (PSO) and weight method that employed
to obtain the best compromise between these costs. Simulation
results on 33-bus distribution test system are presented to
demonstrate the effectiveness of the proposed procedure.
Abstract: The periodic mixed convection of a water-copper
nanofluid inside a rectangular cavity with aspect ratio of 3 is
investigated numerically. The temperature of the bottom wall of the
cavity is assumed greater than the temperature of the top lid which
oscillates horizontally with the velocity defined as u = u0 sin (ω t).
The effects of Richardson number, Ri, and volume fraction of
nanoparticles on the flow and thermal behavior of the nanofluid are
investigated. Velocity and temperature profiles, streamlines and
isotherms are presented. It is observed that when Ri < 1, heat transfer
rate is much greater than when Ri > 1. The higher value of Ri
corresponds to a lower value of the amplitude of the oscillation of
Num in the steady periodic state. Moreover, increasing the volume
fraction of the nanoparticles increases the heat transfer rate.
Abstract: The commercial white tyres are usually used for forklifts in food and medicine industries. Conventionally, silica is used as reinforcement in the tyres. However, the adhesion between silica particles and rubber is remarkably poor. To improve the problem of adhesion and hence enhance wear resistance, modification of silica surface is one of the solutions. In this work, the natural rubber compound blending with polyisoprene-coated silica prepared by admicellar polymerization technique was studied to compare with the natural rubber compound of unmodified silica. The surface characterization of modified silica was also examined by SEM, FTIR, and TGA. The results show that polyisoprene-coated silica/natural rubber compound gave better overall mechanical properties, especially wear resistance with the improvement of the adhesion between silica and natural rubber matrix that can be seen in the SEM micrograph.
Abstract: This presentation narrates the comparative analysis of
the dissolution data nimesulide microparticles prepared with
ethylcellulose, hydroxypropyl methylcellulose, chitosan and
Poly(D,L-lactide-co-glycolide) as polymers. The analysis of release
profiles showed that the variations noted in the release behavior of
nimesulide from various microparticulate formulations are due to the
nature of used polymer. In addition, maximum retardation in the
nimesulide release was observed with HPMC (floating particles).
Thus HPMC miacroparticles may be preferably employed for
sustained release dosage form development.
Abstract: The purpose of this work was to inspect the potential
of vincristine-dextran complex loaded solid lipid nanoparticles for
drug delivery to the brain.
The nanoparticles were stained with a fluorescence dye and their
plasma pharmacokinetic and brain concentrations were investigated
following injection to rats.
The result revealed a significant improvement in the plasma
concentration profile of the SLN injected animals as well as a sharp
increased concentration in the brains.
Abstract: Liners are made to protect the groundwater table from
the infiltration of leachate which normally carries different kinds of
toxic materials from landfills. Although these liners are engineered to
last for long period of time; unfortunately these liners fail; therefore,
toxic materials pass to groundwater. This paper focuses on the
changes of the hydraulic conductivity of a sand-bentonite liner due to
the infiltration of biofuel and ethanol fuel. Series of laboratory tests
were conducted in 20-cm-high PVC columns. Several compositions
of sand-bentonite liners were tested: 95% sand: 5% bentonite; 90%
sand: 10% bentonite; and 100% sand (passed mesh #40). The
columns were subjected to extreme pressures of 40 kPa, and 100 kPa
to evaluate the transport of alternative fuels (biofuel and ethanol
fuel). For comparative studies, similar tests were carried out using
water. Results showed that hydraulic conductivity increased due to
the infiltration of alternative fuels through the liners. Accordingly,
the increase in the hydraulic conductivity showed significant
dependency on the type of liner mixture and the characteristics of the
liquid. The hydraulic conductivity of a liner (subjected to biofuel
infiltration) consisting of 5% bentonite: 95% sand under pressure of
40 kPa and 100 kPa had increased by one fold. In addition, the
hydraulic conductivity of a liner consisting of 10% bentonite: 90%
sand under pressure of 40 kPa and 100 kPa and infiltrated by biofuel
had increased by three folds. On the other hand, the results obtained
by water infiltration under 40 kPa showed lower hydraulic
conductivities of 1.50×10-5 and 1.37×10-9 cm/s for 5% bentonite:
95% sand, and 10% bentonite: 90% sand, respectively. Similarly,
under 100 kPa, the hydraulic conductivities were 2.30×10-5 and
1.90×10-9 cm/s for 5% bentonite: 95% sand, and 10% bentonite: 90%
sand, respectively.
Abstract: This paper presents an algorithm of particle swarm
optimization with reduction for global optimization problems. Particle
swarm optimization is an algorithm which refers to the collective
motion such as birds or fishes, and a multi-point search algorithm
which finds a best solution using multiple particles. Particle
swarm optimization is so flexible that it can adapt to a number
of optimization problems. When an objective function has a lot of
local minimums complicatedly, the particle may fall into a local
minimum. For avoiding the local minimum, a number of particles are
initially prepared and their positions are updated by particle swarm
optimization. Particles sequentially reduce to reach a predetermined
number of them grounded in evaluation value and particle swarm
optimization continues until the termination condition is met. In order
to show the effectiveness of the proposed algorithm, we examine the
minimum by using test functions compared to existing algorithms.
Furthermore the influence of best value on the initial number of
particles for our algorithm is discussed.
Abstract: In this study, the effect of mechanical activation on the synthesis of Fe3Al/Al2O3 nanocomposite has been investigated by using mechanochemical method. For this purpose, Aluminum powder and hematite as precursors, with stoichiometric ratio, have been utilized and other effective parameters in milling process were kept constant. Phase formation analysis, crystallite size measurement and lattice strain were studied by X-ray diffraction (XRD) by using Williamson-Hall method as well as microstructure and morphology were explored by Scanning electron microscopy (SEM). Also, Energy-dispersive X-ray spectroscopy (EDX) analysis was used in order to probe the particle distribution. The results showed that after 30-hour milling, the reaction was started, combustibly done and completed.