Abstract: In this paper, thick walled Cylindrical tanks or tubes
made of functionally graded material under internal pressure and
temperature gradient are studied. Material parameters have been
considered as power functions. They play important role in the
elastoplastic behavior of these materials. To clarify their role,
different materials with different parameters have been used under
temperature gradient. Finally, their effect and loading effect have
been determined in first yield point. Also, the important role of
temperature gradient was also shown. At the end the study has been
results obtained from changes in the elastic modulus and yield stress.
Also special attention is also given to the effects of this internal
pressure and temperature gradient in the creation of tensile and
compressive stresses.
Abstract: This paper presents a new method to design nonlinear
feedback linearization controller for PEMFCs (Polymer Electrolyte
Membrane Fuel Cells). A nonlinear controller is designed based on
nonlinear model to prolong the stack life of PEMFCs. Since it is
known that large deviations between hydrogen and oxygen partial
pressures can cause severe membrane damage in the fuel cell,
feedback linearization is applied to the PEMFC system so that the
deviation can be kept as small as possible during disturbances or load
variations. To obtain an accurate feedback linearization controller,
tuning the linear parameters are always important. So in proposed
study NSGA (Non-Dominated Sorting Genetic Algorithm)-II method
was used to tune the designed controller in aim to decrease the
controller tracking error. The simulation result showed that the
proposed method tuned the controller efficiently.
Abstract: The manufacturing technology of band cotton is very
delicate and depends to choice of certain parameters such as torsion
of warp yarn.
The fabric elasticity is achieved without the use of any elastic
material, chemical expansion, artificial or synthetic and it’s capable
of creating pressures useful for therapeutic treatments.
Before use, the band is subjected to treatments of specific
preparation for obtaining certain elasticity, however, during its
treatment, there are some regression parameters. The dependence of
manufacturing parameters on the quality of the chemical treatment
was confirmed.
The aim of this work is to improve the properties of the fabric
through the development of manufacturing technology appropriately.
Finally for the treatment of the strip pancake 100% cotton, a
treatment method is recommended.
Abstract: Nonalcoholic fatty liver disease (NAFLD) has
increased in conjunction with obesity. The accuracy of risk factors
for detecting NAFLD in obese adolescents has not undergone a
formal evaluation. The aim of this study was to evaluate predictors of
NAFLD among Egyptian female obese adolescents. The study
included 162 obese female adolescents. All were subjected to
anthropometry, biochemical analysis and abdominal ultrasongraphic
assessment. Metabolic syndrome (MS) was diagnosed according to
the IDF criteria. Significant association between presence of MS and
NAFLD was observed. Obese adolescents with NAFLD had
significantly higher levels of ALT, triglycerides, fasting glucose,
insulin, blood pressure and HOMA-IR, whereas decreased HDL-C
levels as compared with obese cases without NAFLD. Receiver–
operating characteristic (ROC) curve analysis shows that ALT is a
sensitive predictor for NAFLD, confirming that ALT can be used as a
marker of NAFLD.
Abstract: In the present work, the effect of load and sliding
distance on the performance tribology of commercially used
aluminium-silicon engine block and piston was evaluated at ambient
conditions with humidity of 80% under dry sliding conditions using a
pin-on-disc with two different loads of 5N and 20N yielding applied
pressure of 0.30MPa and 1.4MPa, respectively, at sliding velocity of
0.29ms-1 and with varying sliding distance ranging from 260m-
4200m. Factors and conditions that had significant effect were
identified. The results showed that the load and the sliding distance
affect the wear rate of the alloys and the wear rate increased with
increasing load for both the alloys. Wear rate also increases almost
linearly at low loads and increase to a maximum then attain a plateau
with increasing sliding distance. For both applied loads the piston
alloy showed the better performance due to higher Ni and Mg
content. The worn surface and wear debris was characterized by
optical microscope, SEM and EDX analyzer. The worn surface was
characterized by surface with shallow grooves at loads while the
groove width and depth increased as the loads increases. Oxidative
wear was found to be the predominant mechanisms in the dry sliding
of Al-Si alloys at low loads.
Abstract: Load carrying capacity of an oil lubricated two-axial
groove journal bearing is simulated by taking into account the
viscosity variations in lubricant due to the addition of TiO2
nanoparticles as lubricant additive. Shear viscosities of TiO2
nanoparticle dispersions in oil are measured for various nanoparticle
additive concentrations. The viscosity model derived from the
experimental viscosities is employed in a modified Reynolds
equation to obtain the pressure profiles and load carrying capacity of
two-axial groove journal bearing. Results reveal an increase in load
carrying capacity of bearings operating on nanoparticle dispersions as
compared to plain oil.
Abstract: The study deals with the challenges in developing a
test rig to test the performance of water lubricated journal bearing.
The test rig is designed to simulate the working conditions of the
bearing in order to understand their performance before they are put
in operation. The bearing that is studied is the commercially available
water lubricated bearing which has a rubber liner bonded with a rigid
metal shell. The lubricant enters the bearing axially through a
pressurized inlet tank and exits to an outlet tank which is at
sufficiently low pressure. The load on the bearing is applied through
the dead weight system which acts both in upward and downward
direction so that net load acts on the bearing. The issues in feeding
the lubricant into the bearing from the inlet side and preventing the
leakage of the lubricant is discussed. The application of the load on
the test bearing while maintaining the bearing afloat is also discussed.
Abstract: The most important part of modern lean low NOx combustors is a premixer where swirlers are often used for intensification of mixing processes and further formation of required flow pattern in combustor liner. Swirling flow leads to formation of complex eddy structures causing flow perturbations. It is able to cause combustion instability. Therefore, at design phase, it is necessary to pay great attention to aerodynamics of premixers. Analysis based on unsteady CFD modeling of swirling flow in production combustor swirler showed presence of large number of different eddy structures that can be conditionally divided into three types relative to its location of origin and a propagation path. Further, features of each eddy type were subsequently defined. Comparison of calculated and experimental pressure fluctuations spectrums verified correctness of computations.
Abstract: Fly ash is an important waste, produced in thermal
power plants which causes very important environmental pollutions.
For this reason the usage and evaluation the fly ash in various areas
are very important. Nearly, 15 million tons/year of fly ash is
produced in Turkey. In this study, usage of fly ash with diatomite and
molasses for heavy metal (Cd) adsorption from wastewater is
investigated. The samples of Seyitomer region fly ash were analyzed
by X-ray fluorescence (XRF) and Scanning Electron Microscope
(SEM) then diatomite (0 and 1% in terms of fly ash, w/w) and
molasses (0-0.75 mL) were pelletized under 30 MPa of pressure for
the usage of cadmium (Cd) adsorption in wastewater. After the
adsorption process, samples of Seyitomer were analyzed using
Optical Emission Spectroscopy (ICP-OES). As a result, it is seen that
the usage of Seyitomer fly ash is proper for cadmium (Cd) adsorption
and an optimum adsorption yield with 52% is found at a compound
with Seyitomer fly ash (10 g), diatomite (0.5 g) and molasses (0.75
mL) at 2.5 h of reaction time, pH:4, 20ºC of reaction temperature and
300 rpm of stirring rate.
Abstract: This study aimed at designing and developing a
mechanical force gauge for the square watermelon mold for the first
time. It also tried to introduce the square watermelon characteristics
and its production limitations. The mechanical force gauge
performance and the product itself were also described. There are
three main designable gauge models: a. hydraulic gauge, b. strain
gauge, and c. mechanical gauge. The advantage of the hydraulic
model is that it instantly displays the pressure and thus the force
exerted by the melon. However, considering the inability to measure
forces at all directions, complicated development, high cost, possible
hydraulic fluid leak into the fruit chamber and the possible influence
of increased ambient temperature on the fluid pressure, the
development of this gauge was overruled. The second choice was to
calculate pressure using the direct force a strain gauge. The main
advantage of these strain gauges over spring types is their high
precision in measurements; but with regard to the lack of conformity
of strain gauge working range with water melon growth, calculations
were faced with problems. Finally the mechanical pressure gauge has
advantages, including the ability to measured forces and pressures on
the mold surface during melon growth; the ability to display the peak
forces; the ability to produce melon growth graph thanks to its
continuous force measurements; the conformity of its manufacturing
materials with the required physical conditions of melon growth; high
air conditioning capability; the ability to permit sunlight reaches the
melon rind (no yellowish skin and quality loss); fast and
straightforward calibration; no damages to the product during
assembling and disassembling; visual check capability of the product
within the mold; applicable to all growth environments (field,
greenhouses, etc.); simple process; low costs and so forth.
Abstract: A blood pressure monitor or sphygmomanometer can
be either manual or automatic, employing respectively either the
auscultatory method or the oscillometric method.
The manual version of the sphygmomanometer involves an
inflatable cuff with a stethoscope adopted to detect the sounds
generated by the arterial walls to measure blood pressure in an artery.
An automatic sphygmomanometer can be effectively used to
monitor blood pressure through a pressure sensor, which detects
vibrations provoked by oscillations of the arterial walls.
The pressure sensor implemented in this device improves the
accuracy of the measurements taken.
Abstract: This study investigates the effect of moisture
conditioning on the Indirect Tensile Strength (ITS) of asphalt
concrete. As a first step, cylindrical samples of 100 mm diameter and
50 mm thick were prepared using a Superpave gyratory compactor.
Next, the samples were conditioned using Moisture Induced
Susceptibility Test (MIST) device at different numbers of moisture
conditioning cycles. In the MIST device, samples are subjected water
pressure through the sample pores cyclically. The MIST conditioned
samples were tested for ITS. Results show that the ITS does not
change significantly with MIST conditioning at the specific pressure
and cycles adopted in this study.
Abstract: In the present work, detailed analysis on flow characteristics of a pair of immiscible liquids through horizontal pipeline is simulated by using ANSYS FLUENT 6.2. Moderately viscous oil and water (viscosity ratio = 107, density ratio = 0.89 and interfacial tension = 0.024 N/m) have been taken as system fluids for the study. Volume of Fluid (VOF) method has been employed by assuming unsteady flow, immiscible liquid pair, constant liquid properties, and co-axial flow. Meshing has been done using GAMBIT. Quadrilateral mesh type has been chosen to account for the surface tension effect more accurately. From the grid independent study, we have selected 47037 number of mesh elements for the entire geometry. Simulation successfully predicts slug, stratified wavy, stratified mixed and annular flow, except dispersion of oil in water, and dispersion of water in oil. Simulation results are validated with horizontal literature data and good conformity is observed. Subsequently, we have simulated the hydrodynamics (viz., velocity profile, area average pressure across a cross section and volume fraction profile along the radius) of stratified wavy and annular flow at different phase velocities. The simulation results show that in the annular flow, total pressure of the mixture decreases with increase in oil velocity due to the fact that pipe cross section is completely wetted with water. Simulated oil volume fraction shows maximum at the centre in core annular flow, whereas, in stratified flow, maximum value appears at upper side of the pipeline. These results are in accord with the actual flow configuration. Our findings could be useful in designing pipeline for transportation of crude oil.
Abstract: The present environmental issues have made aircraft jet noise reduction a crucial problem in aero-acoustics research. Acoustic studies reveal that addition of chevrons to the nozzle reduces the sound pressure level reasonably with acceptable reduction in performance. In this paper comprehensive numerical studies on acoustic characteristics of different types of chevron nozzles have been carried out with non-reacting flows for the shape optimization of chevrons in supersonic nozzles for aerospace applications. The numerical studies have been carried out using a validated steady 3D density based, k-ε turbulence model. In this paper chevron with sharp edge, flat edge, round edge and U-type edge are selected for the jet acoustic characterization of supersonic nozzles. We observed that compared to the base model a case with round-shaped chevron nozzle could reduce 4.13% acoustic level with 0.6% thrust loss. We concluded that the prudent selection of the chevron shape will enable an appreciable reduction of the aircraft jet noise without compromising its overall performance. It is evident from the present numerical simulations that k-ε model can predict reasonably well the acoustic level of chevron supersonic nozzles for its shape optimization.
Abstract: Flow forming is widely used in many industries, especially in defence technology industries. Pressure vessels requirements are high precision, light weight, seamless and optimum strength. For large pressure vessels, flow forming by 3 rollers machine were used. In case of long range rocket motor case flow forming and welding of pressure vessels have been used for manufacturing. Due to complication of welding process, researchers had developed 4 meters length pressure vessels without weldment by 4 rollers flow forming machine. Design and preparation of preform work pieces are performed. The optimization of flow forming parameter such as feed rate, spindle speed and depth of cut will be discussed. The experimental result shown relation of flow forming parameters to quality of flow formed tube and prototype pressure vessels have been made.
Abstract: This article aims to study the effect of pressure on rocket motor case by Finite Element Method simulation to select optimal material in rocket motor manufacturing process. In this study, cylindrical tubes with outside diameter of 122 mm and thickness of 3 mm are used for simulation. Defined rocket motor case materials are AISI4130, AISI1026, AISI1045, AL2024 and AL7075. Internal pressure used for the simulation is 22 MPa.
The result from Finite Element Method shows that at a pressure of 22 MPa rocket motor case produced by AISI4130, AISI1045 and AL7075 can be used. A comparison of the result between AISI4130, AISI1045 and AL7075 shows that AISI4130 has minimum principal stress and confirm the results of Finite Element Method by the used of calculation method found that, the results from Finite Element Method has good reliability.
Abstract: A vacuum fractionation technique was introduced to remove ethanol from fermentation broth. The effect of initial glucose and ethanol concentrations were investigated for specific productivity. The inhibitory ethanol concentration was observed at 100 g/L. In order to increase the fermentation performance, the ethanol product was removed as soon as it is produced. The broth was boiled at 35oC by reducing the pressure to 65 mBar. The ethanol/water vapor was fractionated for up to 90 wt% before leaving the column. Ethanol concentration in the broth was kept lower than 25 g/L, thus minimized the product inhibition effect to the yeast cells. For batch extractive fermentation, a high substrate utilization rate was obtained at 26.6 g/L.h and most of glucose was consumed within 21 h. For repeated-batch extractive fermentation, addition of glucose was carried out up to 9 times and ethanol was produced more than 8-fold higher than batch fermentation.
Abstract: It is necessary to manage the fatigue crack growth (FCG) once those cracks are detected during in-service inspections. In this paper, a simulation program (FCG-System) is developed utilizing the commercial software ABAQUS with its object-oriented programming interface to simulate the fatigue crack path and to compute the corresponding fatigue life. In order to apply FCG-System in large-scale marine structures, the substructure modeling technique is integrated in the system under the consideration of structural details and load shedding during crack growth. Based on the nodal forces and nodal displacements obtained from finite element analysis, a formula for shell elements to compute stress intensity factors is proposed in the view of virtual crack closure technique. The cracks initiating from the intersection of flange and the end of the web-stiffener are investigated for fatigue crack paths and growth lives under water pressure loading and axial force loading, separately. It is found that the FCG-System developed by authors could be an efficient tool to perform fatigue crack growth analysis on marine structures.
Abstract: The most important problem occurs on oil spills in sea
water is to reduce the oil spills size. This study deals with the
development of high pressurized nozzle using dispersion method for
oil leakage in offshore. 3D numerical simulation results were
obtained using ANSYS Fluent 13.0 code and correlate with the
experimental data for validation. This paper studies the contribution
of the process on flow speed and pressure of the flow from two
different geometrical designs of nozzles and to generate a spray
pattern suitable for dispersant application. Factor of size distribution
of droplets generated by the nozzle is calculated using pressures
ranging from 2 to 6 bars. Results obtain from both analyses shows a
significant spray pattern and flow distribution as well as distance.
Results also show a significant contribution on the effect of oil
leakage in terms of the diameter of the oil spills break up.
Abstract: The sound pressure level (SPL) of the moving-coil
loudspeaker (MCL) is often simulated and analyzed using the lumped
parameter model. However, the SPL of a MCL cannot be simulated
precisely in the high frequency region, because the value of cone
effective area is changed due to the geometry variation in different
mode shapes, it is also related to affect the acoustic radiation mass and
resistance. Herein, the paper presents the inverse method which has a
high ability to measure the value of cone effective area in various
frequency points, also can estimate the MCL electroacoustic
parameters simultaneously. The proposed inverse method comprises
the direct problem, adjoint problem, and sensitivity problem in
collaboration with nonlinear conjugate gradient method. Estimated
values from the inverse method are validated experimentally which
compared with the measured SPL curve result. Results presented in
this paper not only improve the accuracy of lumped parameter model
but also provide the valuable information on loudspeaker cone design.