Abstract: Many aluminum motorcycle parts produced by a high
pressure die casting. Some parts such as fuel caps were a thin and
complex shape. This part risked for porosities and blisters on surface
if it only depended on an experience of mold makers for mold design.
This research attempted to use CAST-DESIGNER software
simulated the high pressure die casting process with the same process
parameters of a motorcycle fuel cap production. The simulated results
were compared with fuel cap products and expressed the same
porosity and blister locations on cap surface. An average of absolute
difference of simulated results was obtained 0.094 mm when
compared the simulated porosity and blister defect sizes on the fuel
cap surfaces with the experimental micro photography. This
comparison confirmed an accuracy of software and will use the
setting parameters to improve fuel cap molds in the further work.
Abstract: Composite material based on Fe3Si micro-particles
and Mn-Zn nano-ferrite was prepared using powder metallurgy
technology. The sol-gel followed by autocombustion process was
used for synthesis of Mn0.8Zn0.2Fe2O4 ferrite. 3 wt.% of mechanically
milled ferrite was mixed with Fe3Si powder alloy. Mixed micro-nano
powder system was homogenized by the Resonant Acoustic Mixing
using ResodynLabRAM Mixer. This non-invasive homogenization
technique was used to preserve spherical morphology of Fe3Si
powder particles. Uniaxial cold pressing in the closed die at pressure
600 MPa was applied to obtain a compact sample. Microwave
sintering of green compact was realized at 800°C, 20 minutes, in air.
Density of the powders and composite was measured by
Hepycnometry. Impulse excitation method was used to measure
elastic properties of sintered composite. Mechanical properties were
evaluated by measurement of transverse rupture strength (TRS) and
Vickers hardness (HV). Resistivity was measured by 4 point probe
method. Ferrite phase distribution in volume of the composite was
documented by metallographic analysis.
It has been found that nano-ferrite particle distributed among
micro- particles of Fe3Si powder alloy led to high relative density
(~93%) and suitable mechanical properties (TRS >100 MPa, HV
~1GPa, E-modulus ~140 GPa) of the composite. High electric
resistivity (R~6.7 ohm.cm) of prepared composite indicate their
potential application as soft magnetic material at medium and high
frequencies.
Abstract: Cell volume, together with membrane potential and
intracellular hydrogen ion concentration, is an essential biophysical
parameter for normal cellular activity. Cell volumes can be altered by
osmotically active compounds and extracellular tonicity.
In this study, a simple mathematical model of osmotically induced
cell swelling and shrinking is presented. Emphasis is given to water
diffusion across the membrane. The mathematical description of the
cellular behavior consists in a system of coupled ordinary differential
equations. We compare experimental data of cell volume alterations
driven by differences in osmotic pressure with mathematical
simulations under hypotonic and hypertonic conditions. Implications
for a future model are also discussed.
Abstract: For the treatment of acute and chronic lung diseases it is preferred to deliver medicaments by inhalation. The drug is delivered directly to tracheobronchial tree. This way allows the given medicament to get directly into the place of action and it makes rapid onset of action and maximum efficiency. The transport of aerosol particles in the particular part of the lung is influenced by their size, anatomy of the lungs, breathing pattern and airway resistance. This article deals with calculation of airway resistance in the lung model of Horsfield. It solves the problem of determination of the pressure losses in bifurcation and thus defines the pressure drop at a given location in the bronchial tree. The obtained data will be used as boundary conditions for transport of aerosol particles in a central part of bronchial tree realized by Computational Fluid Dynamics (CFD) approach. The results obtained from CFD simulation will allow us to provide information on the required particle size and optimal inhalation technique for particle transport into particular part of the lung.
Abstract: A novel hybrid model of the lumbar spine, allowing
fast static and dynamic simulations of the disc pressure
and the spine mobility, is introduced in this work. Our
contribution is to combine rigid bodies, deformable finite
elements, articular constraints, and springs into a unique model
of the spine. Each vertebra is represented by a rigid body
controlling a surface mesh to model contacts on the facet
joints and the spinous process. The discs are modeled using
a heterogeneous tetrahedral finite element model. The facet
joints are represented as elastic joints with six degrees of
freedom, while the ligaments are modeled using non-linear
one-dimensional elastic elements. The challenge we tackle
is to make these different models efficiently interact while
respecting the principles of Anatomy and Mechanics.
The mobility, the intradiscal pressure, the facet joint force and
the instantaneous center of rotation of the lumbar spine are
validated against the experimental and theoretical results of
the literature on flexion, extension, lateral bending as well as
axial rotation.
Our hybrid model greatly simplifies the modeling task and
dramatically accelerates the simulation of pressure within the
discs, as well as the evaluation of the range of motion and the
instantaneous centers of rotation, without penalizing precision.
These results suggest that for some types of biomechanical
simulations, simplified models allow far easier modeling and
faster simulations compared to usual full-FEM approaches
without any loss of accuracy.
Abstract: Exact solution of an unsteady flow of elastico-viscous
fluid through a porous media in a tube of spherical cross section
under the influence of constant pressure gradient has been obtained in
this paper. Initially, the flow is generated by a constant pressure
gradient. After attaining the steady state, the pressure gradient is
suddenly withdrawn and the resulting fluid motion in a tube of
spherical cross section by taking into account of the porosity factor of
the bounding surface is investigated. The problem is solved in twostages
the first stage is a steady motion in tube under the influence of
a constant pressure gradient, the second stage concern with an
unsteady motion. The problem is solved employing separation of
variables technique. The results are expressed in terms of a nondimensional
porosity parameter (K) and elastico-viscosity parameter
(β), which depends on the Non-Newtonian coefficient. The flow
parameters are found to be identical with that of Newtonian case as
elastic-viscosity parameter tends to zero and porosity tends to
infinity. It is seen that the effect of elastico-viscosity parameter,
porosity parameter of the bounding surface has significant effect on
the velocity parameter.
Abstract: The present work aims to throw light on the effects of
arcing in air on the surface state of contact pastilles made of silvernickel
Ag-Ni (60/40). Also, the photoelectric emission from these
electrical contacts has been investigated in the spectral range of 196-
256 nm. In order to study the effects of arcing on the EWF, the
metallic samples were subjected to electrical arcs in air, at
atmospheric pressure and room temperature, after that, they have
been introduced into the vacuum chamber of an experimental UHV
set-up for EWF measurements. Both Fowler method of isothermal
curves and linearized Fowler plots were used for the measurement of
the EWF by the photoelectric effect.
It has been found that the EWF varies with the number of applied
arcs. Thus, after 500 arcs in air, the observed EWF increasing is
probably due to progressive inclusion of oxide on alloy surface.
Microscopic examination is necessary to get better understandings on
EWF of silver alloys, for both virgin and arced electrical contacts.
Abstract: In this report we have discussed the theoretical aspects
of the flow transformation, occurring through a series of bifurcations.
The parameters and their continuous diversion, the intermittent bursts
in the transition zone, variation of velocity and pressure with time,
effect of roughness in turbulent zone, and changes in friction factor
and head loss coefficient as a function of Reynolds number for a
transverse flow across a cylinder have been discussed. An analysis of
the variation in the wake length with Reynolds number was done in
FORTRAN.
Abstract: A parametric study on circular thin-walled pipes
subjected to pure bending is performed. Both straight and curved
pipes are considered. Ratio D/t, initial pipe curvature and internal
pressure are the parameters varying in the analyses. The study is
mainly FEA-based.
It is found that negative curvatures (opposite to bending moment)
considerably increase stiffness and buckling limit of the pipe when no
internal pressure is acting and, similarly, positive curvatures decrease
the stiffness and buckling limit. For internal pressurised pipes the
effects of initial pipe curvature are less relevant. Results show that
this phenomenon is in relationship with the cross-section deformation
due to bending moment, which undergoes relevant ovalisation for no
pressurised pipes and little ovalisation for pressurised pipes.
Abstract: There is an evident trend to elevate pressure ratio of a
single stage of a turbo compressors - axial compressors in particular.
Whilst there was an opinion recently that a pressure ratio 1,9 was a
reasonable limit, later appeared information on successful modeling
tested of stages with pressure ratio up to 2,8. The authors recon that
lack of information on high pressure stages makes actual a study of
rational choice of design parameters before high supersonic flow
problems solving. The computer program of an engineering type was
developed. Below is presented a sample of its application to study
possible parameters of the impeller of the stage with pressure ratio
3,0. Influence of two main design parameters on expected efficiency,
periphery blade speed and flow structure is demonstrated. The results
had lead to choose a variant for further analysis and improvement by
CFD methods.
Abstract: It has experimentally been proved that the
performance of compression ignition (C.I.) engine is spray
characteristics related. In modern diesel engine the spray formation
and the eventual combustion process are the vital processes that offer
more challenges towards enhancing the engine performance. In the
present work the numerical simulation has been carried out for
evaporating diesel sprays using Fluent software. For computational
fluid dynamics simulation “Meshing” is done using Gambit software
before transmitting it into Fluent. The simulation is carried out using
hot bomb conditions under varying chamber conditions such as gas
pressure, nozzle diameter and fuel injection pressure. For comparison
purpose, the numerical simulations the chamber conditions were kept
the same as that of the experimental data. At varying chamber
conditions the spray penetration rates are compared with the existing
experimental results.
Abstract: Solenoid operated electromagnetic control valve
(ECV) playing an important role for car’s air conditioning control
system. ECV is used in external variable displacement swash plate
type compressor and controls the entire air conditioning system by
means of a pulse width modulation (PWM) input signal supplying
from an external source (controller). Complete form of ECV contains
number of internal features like valve body, core, valve guide,
plunger, guide pin, plunger spring, bellows etc. While designing the
ECV; dimensions of different internal items must meet the standard
requirements as it is quite challenging. In this research paper,
especially the dimensioning of ECV body and its three pressure ports
through which the air/refrigerant passes are considered. Here internal
leakage test analysis of ECV body is being carried out from its
discharge port (Pd) to crankcase port (Pc) when the guide valve is
placed inside it. The experiments have made both in ordinary and
digital system using different assumptions and thereafter compare the
results.
Abstract: At certain depths during large diameter displacement
pile driving, rebound well over 0.25 inches was experienced,
followed by a small permanent-set during each hammer blow. High
pile rebound (HPR) soils may stop the pile driving and results in a
limited pile capacity. In some cases, rebound leads to pile damage,
delaying the construction project, and the requiring foundations
redesign. HPR was evaluated at seven Florida sites, during driving of
square precast, prestressed concrete piles driven into saturated, fine
silty to clayey sands and sandy clays. Pile Driving Analyzer (PDA)
deflection versus time data recorded during installation, was used to
develop correlations between cone penetrometer (CPT) pore-water
pressures, pile displacements and rebound. At five sites where piles
experienced excessive HPR with minimal set, the pore pressure
yielded very high positive values of greater than 20 tsf. However, at
the site where the pile rebounded, followed by an acceptable
permanent-set, the measured pore pressure ranged between 5 and 20
tsf. The pore pressure exhibited values of less than 5 tsf at the site
where no rebound was noticed. In summary, direct correlations
between CPTu pore pressure and rebound were produced, allowing
identification of soils that produce HPR.
Abstract: Negative pressure phenomenon appears in many
thermodynamic, geophysical and biophysical processes in the Nature
and technological systems. For more than 100 years of the laboratory
researches beginning from F. M. Donny’s tests, the great values of
negative pressure have been achieved. But this phenomenon has not
been practically applied, being only a nice lab toy due to the special
demands for the purity and homogeneity of the liquids for its
appearance. The possibility of creation of direct wave of negative
pressure in real heterogeneous liquid systems was confirmed
experimentally under the certain kinetic and hydraulic conditions.
The negative pressure can be considered as the factor of both useful
and destroying energies. The new approach to generation of the
negative pressure waves in impure, unclean fluids has allowed the
creation of principally new energy saving technologies and
installations to increase the effectiveness and efficiency of different
production processes. It was proved that the negative pressure is one
of the main factors causing hard troubles in some technological and
natural processes. Received results emphasize the necessity to take
into account the role of the negative pressure as an energy factor in
evaluation of many transient thermohydrodynamic processes in the
Nature and production systems.
Abstract: A game for training of breath (TRABR) for continuous
monitoring of pulmonary ventilation during the patients’ therapy
focuses especially on monitoring of their ventilation processes. It is
necessary to detect, monitor and differentiate abdominal and thoracic
breathing during the therapy. It is a fun form of rehabilitation where
the patient plays and also practicing isolated breathing. Finally the
game to practice breath was designed to evaluate whether the patient
uses two types of breathing or not.
Abstract: Burnishing is increasingly used as a finishing operation to improve surface roughness and surface hardness. This can be achieved by applying a hard ball or roller onto metallic surfaces under pressure, in order to achieve many advantages in the metallic surface. In the present work, the feed rate, speed and force have been considered as the basic burnishing parameters to study the surface roughness and surface hardness of metallic matrix composites. The considered metal matrix composites were made from Aluminum-Magnesium-Graphite with five different weight percentage of graphite. Both effects of burnishing parameters mentioned above and the graphite percentage on the surface hardness and surface roughness of the metallic matrix composites were studied. The results of this investigation showed that the surface hardness of the metallic composites increases with the increase of the burnishing force and decreases with the increase in the burnishing feed rate and burnishing speed. The surface roughness of the metallic composites decreases with the increasing of the burnishing force, feed rate, and speed to certain values, then it starts to increase. On the other hand, the increase in the weight percentage of the graphite in the considered composites causes a decrease in the surface hardness and an increase in the surface roughness.
Abstract: The rate of natural gas dissociation from the Coal
Matrix depends on depressurization of reservoir through removing of
the cleat water from the coal seam. These waters are similar to brine
and aged of very long years. For improving the connectivity through
fracking /fracturing, high pressure liquids are pumped off inside the
coal body. A significant quantity of accumulated water, a combined
mixture of cleat water and fracking fluids (back flow water) is
pumped out through gas well. In Queensland, Australia Coal Seam
Gas (CSG) industry is in booming state and estimated of 30,000 wells
would be active for CSG production forecasting life span of 30 years.
Integrated water management along with water softening programs is
practiced for subsequent treatment and later on discharge to nearby
surface water catchment. Water treatment is an important part of the
CSG industry. A case study on a CSG site and review on the test
results are discussed for assessing the Standards & Practices for
management of CSG by-product water and their subsequent disposal
activities. This study was directed toward (i) water management and
softening process in Spring Gully CSG field, (ii) Comparative
analysis on experimental study and standards and (iii) Disposal of the
treated water. This study also aimed for alternative usages and their
impact on vegetation, living species as well as long term effects.
Abstract: The design, manufacture, and operation of thin-walled
pressure vessels must be based on maximum safe operating pressure
and an adequate factor of safety (FoS). This research paper first
reports experimental evaluation of longitudinal and hoops stresses
based on working pressure as well as maximum pressure; and then
includes a critical study of factor of safety (FoS) in the design of a
glass fiber pressure vessel. Experimental work involved the use of
measuring instruments and the readings from pressure gauges.
Design calculations involved the computations of design stress and
FoS; the latter was based on breaking strength of 55 MPa for the
glass fiber (pressure-vessel material). The experimentally determined
FoS value has been critically compared with the general FoS allowed
in the design of glass fiber pressure vessels.
Abstract: In this research, waterglass based aerogel powder was
prepared by sol–gel process and ambient pressure drying. Inspired by
limited dust releasing, aerogel powder was introduced to the PET
electrospinning solution in an attempt to create required bulk and
surface structure for the nanofibers to improve their hydrophobic and
insulation properties. The samples evaluation was carried out by
measuring density, porosity, contact angle, heat transfer, FTIR, BET,
and SEM. According to the results, porous silica aerogel powder was
fabricated with mean pore diameter of 24 nm and contact angle of
145.9º. The results indicated the usefulness of the aerogel powder
confined into nanofibers to control surface roughness for
manipulating superhydrophobic nanowebs with water contact angle
of 147º. It can be due to a multi-scale surface roughness which was
created by nanowebs structure itself and nanofibers surface
irregularity in presence of the aerogels while a layer of fluorocarbon
created low surface energy. The wettability of a solid substrate is an
important property that is controlled by both the chemical
composition and geometry of the surface. Also, a decreasing trend in
the heat transfer was observed from 22% for the nanofibers without
any aerogel powder to 8% for the nanofibers with 4% aerogel
powder. The development of thermal insulating materials has become
increasingly more important than ever in view of the fossil energy
depletion and global warming that call for more demanding energysaving
practices.
Abstract: Cavitation in cryogenic liquids is widely present in
contemporary science. In the current study, we re-examine a
previously validated acoustic cavitation model which was developed
for a gas bubble in liquid water. Furthermore, simulations of
cryogenic fluids including the thermal effect, the effect of acoustic
pressure amplitude and the frequency of sound field on the bubble
dynamics are presented. A gas bubble (Helium) in liquids Nitrogen,
Oxygen and Hydrogen in an acoustic field at ambient pressure and
low temperature is investigated numerically. The results reveal that
the oscillation of the bubble in liquid Hydrogen fluctuates more than
in liquids Oxygen and Nitrogen. The oscillation of the bubble in
liquids Oxygen and Nitrogen is approximately similar.