Abstract: This paper presents an experimental investigation of
transformer dielectric response and solid insulation water content.
The dielectric response was carried out on the base of Hybrid
Frequency Dielectric Spectroscopy and Polarization Current
measurements method (FDS &PC). The calculation of the water
content in paper is based on the water content in oil and the obtained
equilibrium curves. A reference measurements were performed at
equilibrium conditions for water content in oil and paper of
transformer at different stable temperatures (25, 50, 60 and 70°C) to
prepare references to evaluate the insulation behavior at the not
equilibrium conditions. Some measurements performed at the
different simulated normal working modes of transformer operation
at the same temperature where the equilibrium conditions. The
obtained results show that when transformer temperature is mach
more than the its ambient temperature, the transformer temperature
decreases immediately after disconnecting the transformer from the
network and this temperature reduction influences the transformer
insulation condition in the measuring process. In addition to the oil
temperature at the near places to the sensors, the temperature
uniformity in transformer which can be changed by a big change in
the load of transformer before the measuring time will influence the
result. The investigations have shown that the extremely influence of
the time between disconnecting the transformer and beginning the
measurements on the results. And the online monitoring for water
content in paper measurements, on the basis of the oil water content
on line monitoring and the obtained equilibrium curves. The
measurements where performed continuously and for about 50 days
without any disconnection in the prepared the adiabatic room.
Abstract: Particulate matter (PM) in ambient air is responsible
for adverse health effects in adults and children. Relatively little is
known about the concentrations, sources and health effects of PM in
indoor air. A monitoring study was conducted in Ankara by three
campaigns in order to measure PM levels in indoor and outdoor
environments to identify and quantify associations between sources
and concentrations. Approximately 82 homes (1st campaign for 42,
2nd campaign for 12, and 3rd campaign for 28), three rooms (living
room, baby-s room and living room used as a baby-s room) and
outdoor ambient at each home were sampled with Grimm
Environmental Dust Monitoring (EDM) 107, during different
seasonal periods of 2011 and 2012. In this study, the relationship
between indoor and outdoor PM levels for particulate matter less than
10 micrometer (.m) (PM10), particulate matter less than 2.5.m
(PM2.5) and particulate matter less than 1.0.m (PM1) were
investigated. The mean concentration of PM10, PM2.5, and PM1.0 at
living room used as baby-s room is higher than living and baby-s
room (or bedroom) for three sampling campaigns. It is concluded that
the household activities and environmental conditions are very
important for PM concentrations in the indoor environments during
the sampling periods. The amount of smokers, being near a main
street and/or construction activities increased the PM concentration.
This study is based on the assessment the relationship between indoor
and outdoor PM levels and the household activities and
environmental conditions
Abstract: This paper presents design and characterization of a
microaccelerometer designated for integration into cataract surgical
probe to detect hardness of different eye tissues during cataract
surgery. Soft posterior lens capsule of eye can be easily damaged in
comparison with hard opaque lens since the surgeon can not see
directly behind cutting needle during the surgery. Presence of
microsensor helps the surgeon to avoid rupturing posterior lens
capsule which if occurs leads to severe complications such as
glaucoma, infection, or even blindness. The microsensor having
overall dimensions of 480 μm x 395 μm is able to deliver significant
capacitance variations during encountered vibration situations which
makes it capable to distinguish between different types of tissue.
Integration of electronic components on chip ensures high level of
reliability and noise immunity while minimizes space and power
requirements. Physical characteristics and results on performance
testing, proves integration of microsensor as an effective tool to aid
the surgeon during this procedure.
Abstract: A low cost Short Message System (SMS) based Home security system equipped with motion, smoke, temperature, humidity and light sensors has been studied and tested. The sensors are controlled by a microprocessor PIC 18F4520 through the SMS having password protection code for the secure operation. The user is able to switch light and the appliances and get instant feedback. Also in cases of emergencies such as fire or robbery the system will send alert message to occupant and relevant civil authorities. The operation of the home security has been tested on Vodafone- Fiji network and Digicel Fiji Network for emergency and feedback responses for 25 samples. The experiment showed that it takes about 8-10s for the security system to respond in case of emergency. It takes about 18-22s for the occupant to switch and monitor lights and appliances and then get feedback depending upon the network traffic.
Abstract: The notion of communicative competence has been deemed fuzzy in communication studies. This fuzziness has led to tensions among engineers across tenures in interpreting what constitutes communicative competence. The study seeks to investigate novice and professional engineers- understanding of the said notion in terms of two main elements of communicative competence: linguistic and rhetorical competence. Novice engineers are final year engineering students, whilst professional engineers represent engineers who have at least 5 years working experience. Novice and professional engineers were interviewed to gauge their perceptions on linguistic and rhetorical features deemed necessary to enhance communicative competence for the profession. Both groups indicated awareness and differences on the importance of the sub-sets of communicative competence, namely, rhetorical explanatory competence, linguistic oral immediacy competence, technical competence and meta-cognitive competence. Such differences, a possible attribute of the learning theory, inadvertently indicate sublime differences in the way novice and professional engineers perceive communicative competence.
Abstract: Acute disseminated encephalomyelitis (ADEM) has
been reported to develop after a hymenoptera sting, but its
pathogenesis is not known in detail. Myelin basic protein (MBP)-
specific T cells have been detected in the blood of patients with
ADEM, and a proportion of these patients develop multiple sclerosis
(MS). In an attempt to understand the mechanisms underlying
ADEM, molecular mimicry between hymenoptera venom peptides
and the human immunodominant MBP peptide was scrutinized,
based on the sequence and structural similarities, whether it was the
root of the disease. The results suggest that the three wasp venom
peptides have low sequence homology with the human
immunodominant MBP residues 85-99. Structural similarity analysis
among the three venom peptides and the MS-related HLA-DR2b
(DRA, DRB1*1501)-associated immunodominant MHC
binding/TCR contact residues 88-93, VVHFFK showed that
hyaluronidase residues 7-12, phospholipase A1 residues 98-103, and
antigen 5 residues 109-114 showed a high degree of similarity
83.3%, 100%, and 83.3% respectively. In conclusion, some wasp
venom peptides, particularly phospholipase A1, may potentially act
as the molecular motifs of the human 3HLA-DR2b-associated
immunodominant MBP88-93, and possibly present a mechanism for
induction of wasp sting-associated ADEM.
Abstract: Nosocomial (i.e., hospital-acquired) infections
(NI) is a major cause of morbidity and mortality in hospitals. NI
rate is higher in intensive care units (ICU) than in the general
ward due to patients with severe symptoms, poor immunity,
and accepted many invasive therapies. Contact behaviors
between health caregivers and patients is one of the infect
factors. It is difficult to obtain complete contact records by
traditional method of retrospective analysis of medical records.
This paper establishes a contact history inferential model
(CHIM) intended to extend the use of Proximity Sensing of
rapid frequency identification (RFID) technology to
transferring all proximity events between health caregivers and
patients into clinical events (close-in events, contact events and
invasive events).The results of the study indicated that the
CHIM can infer proximity care activities into close-in events
and contact events.
The infection control team could redesign and build optimal
workflow in the ICU according to the patient-specific contact
history which provided by our automatic tracing system.
Abstract: In this paper application of artificial intelligence for
baby and children caring is studied. Then a new idea for injury
prevention and safety announcement is presented by using digital
image processing. The paper presents the structure of the proposed
system. The system determines the possibility of the dangers for
children and babies in yards, gardens and swimming pools or etc. In
the presented idea, multi camera System is used and receiver videos
are processed to find the hazardous areas then the entrance of
children and babies in the determined hazardous areas are analyzed.
In this condition the system does the programmed action capture,
produce alarm or tone or send message.
Abstract: Performance management seems to be essential in
business area and is also an exciting topic. Despite significant and
myriads of research efforts, performance management guide today as a
rigorous approach is still in an immature state and metrics are often
selected based on intuitive and heuristic approach. In R&D side, the
difficulty to guide the proper performance management is even more
increasing due to the natural characteristics of R&D such as unique or
domain-specific problems. In our approach, we present R&D
performance management guide considering various characteristics of
R&D side: performance evaluation objectives, dimensions, metrics,
and uncertainties of R&D sector.
Abstract: 28 healthy adult Maradi bucks were used to evaluate
sperm production and sperm storage capacity in the breed. Daily
sperm production (DSP) averaged 0.55±0.05x109, while the daily
sperm production/g (DSP/g) was 1.37±0.12 x107. Gonadal sperm
reserve was 1.99±0.18 x109, while the caput, upper corpus and lower
corpus averaged 0.58±0.04 x109, 0.36±0.02 x109 and 0.33±0.08 x109
respectively. The proximal cauda, mid cauda, distal cauda and ductus
deferens had values of 0.68±0.10 x109, 1.23±0.16 x109,1.87±0.
x109and 0.17±0.05 x109 respectively. The relative contributions of
the respective epididymal sections and ductus deferens to the total
extragonadal sperm reserves were, 11.11%, 6.89%, 6.32%, 13.03%,
23.56%, 35.82% and 3.26% respectively. Gonadal sperm reserves
were significantly higher (p0.05) to
mid cauda and distal cauda epididymal reserves.
Abstract: Plants are rich sources of bioactive compounds. In this study the photochemical screening of hexane, ethanolic and aqueous extracts of roots and latex of jojoba (Simmondsia chinensis) plant revealed the presence of saponins, tannins, alkaloids, steroids and glycosides. Ethanolic extract was found to be richer in these metabolites than hexane, aqueous extracts and latex. The extracts and latex displayed effective antimicrobial activity against Salmonella typhimurium, Bacillus cereus, Clostridium perfringens, Staphylococcus aureus, Escherichia coli, Candida albicans and Aspergillus flavus. The increase in volume of the extracts and latex caused more activity, as shown by zones of inhibition. Candida albicans growth was inhibited only by hexane extract. Jojoba latex was not effective against Candida albicans at 0.1 and 0.5 ml extracts concentration but showed 5mm zone of inhibition at (1.0 ml). Lower volume (0.1ml) of latex encouraged Aspergillus flavus growth, while at (1.00 ml) reduced its mycelial growth. Thus, jojoba root extracts and latex can be of potential natural antimicrobial agents.
Abstract: Quantitative trait loci (QTL) experiments have yielded
important biological and biochemical information necessary for
understanding the relationship between genetic markers and
quantitative traits. For many years, most QTL algorithms only
allowed one observation per genotype. Recently, there has been an
increasing demand for QTL algorithms that can accommodate more
than one observation per genotypic distribution. The Bayesian
hierarchical model is very flexible and can easily incorporate this
information into the model. Herein a methodology is presented that
uses a Bayesian hierarchical model to capture the complexity of the
data. Furthermore, the Markov chain Monte Carlo model composition
(MC3) algorithm is used to search and identify important markers. An
extensive simulation study illustrates that the method captures the
true QTL, even under nonnormal noise and up to 6 QTL.
Abstract: The overall objective of this research is a strain
improvement technology for efficient pectinase production. A novel
cells cultivation technology by immobilization of fungal cells has
been studied in long time continuous fermentations. Immobilization
was achieved by using of new material for absorption of stores of
immobilized cultures which was for the first time used for
immobilization of microorganisms. Effects of various conditions of
nitrogen and carbon nutrition on the biosynthesis of pectolytic
enzymes in Aspergillus awamori 1-8 strain were studied. Proposed
cultivation technology along with optimization of media components
for pectinase overproduction led to increased pectinase productivity
in Aspergillus awamori 1-8 from 7 to 8 times. Proposed technology
can be applied successfully for production of major industrial
enzymes such as α-amylase, protease, collagenase etc.
Abstract: Shadoo protein (Sho) was described in 2003 as the newest member of Prion protein superfamily [1]. Sho has similar structural motifs like prion protein (PrP) that is known for its central role in transmissible spongiform enchephalopathies. Although a great number of functions have been proposed, the exact physiological function of PrP is not known yet. Investigation of the function and localization of Sho may help us to understand the function of the Prion protein superfamily. Analyzing the subcellular localization of YFP-tagged forms of Sho, we detected the protein in the plasma membrane and in the nucleus of various cell lines. To reveal the localization of the endogenous protein we generated antibodies against Shadoo as well as employed commercially available anti-Shadoo antibodies: i) EG62 anti-mouse Shadoo antibody generated by Eurogentec Ltd.; ii) S-12 anti-human Shadoo antibody by Santa Cruz Biotechnology Inc.; iii) R-12 anti-mouse Shadoo antibody by Santa Cruz Biotechnology Inc.; iv) SPRN antibody against human Shadoo by Abgent Inc. We carried out immunocytochemistry on non-transfected HeLa, Zpl 2-1, Zw 3-5, GT1-1, GT1-7 and SHSY5Y cells as well as on YFP-Sho, Sho-YFP, and YFP-GPI transfected HeLa cells. Their specificity (in antibody-peptide competition assay) and co-localization (with the YFP signal) were assessed.
Abstract: This study proposes a basic molecular formula for all
proteins. A total of 10,739 proteins belonging to 9 different protein
groups classified on the basis of their functions were selected
randomly. They included enzymes, storage proteins, hormones,
signalling proteins, structural proteins, transport proteins,
immunoglobulins or antibodies, motor proteins and receptor proteins.
After obtaining the protein molecular formula using the ProtParam
tool, the H/C, N/C, O/C, and S/C ratios were determined for each
randomly selected sample. In this case, H, N, O, and S coefficients
were specified per carbon atom. Surprisingly, the results
demonstrated that H, N, O, and S coefficients for all 10,739 proteins
are similar and highly correlated. This study demonstrates that
despite differences in the structure and function, all known proteins
have a similar basic molecular formula CnH1.58 ± 0.015nN0.28 ± 0.005nO0.30
± 0.007nS0.01 ± 0.002n. The total correlation between all coefficients was
found to be 0.9999.
Abstract: The main aim is to perform mutational analysis of CTLA4 gene Exon 1 in SLE patients. A total of 61 SLE patients fulfilling “American College of Rheumatology (ACR) criteria" and 61 controls were enrolled in this study. The region of CTLA4 gene exon 1 was amplified by using Step-down PCR technique. Extracted DNA of band 354 bp was sequenced to analyze mutations in the exon-1 of CTLA-4 gene. Further, protein sequences were identified from nucleotide sequences of CTLA4 Exon 1 by using Expasy software and through Blast P software it was found that CTLA4 protein sequences of Pakistani SLE patients were similar to that of Chinese SLE population. No variations were found after patients sequences were compared with that of the control sequence. Furthermore it was found that CTLA4 protein sequences of Pakistani SLE patients were similar to that of Chinese SLE population. Thus CTLA4 gene may not be responsible for an autoimmune disease SLE.
Abstract: In this paper, based on a novel synthesis, a set of new simplified circuit design to implement the linguistic-hedge operations for adjusting the fuzzy membership function set is presented. The circuits work in current-mode and employ floating-gate MOS (FGMOS) transistors that operate in weak inversion region. Compared to the other proposed circuits, these circuits feature severe reduction of the elements number, low supply voltage (0.7V), low power consumption (60dB). In this paper, a set of fuzzy linguistic hedge circuits, including absolutely, very, much more, more, plus minus, more or less and slightly, has been implemented in 0.18 mm CMOS process. Simulation results by Hspice confirm the validity of the proposed design technique and show high performance of the circuits.
Abstract: One of the purposes of the robust method of
estimation is to reduce the influence of outliers in the data, on the
estimates. The outliers arise from gross errors or contamination from
distributions with long tails. The trimmed mean is a robust estimate.
This means that it is not sensitive to violation of distributional
assumptions of the data. It is called an adaptive estimate when the
trimming proportion is determined from the data rather than being
fixed a “priori-.
The main objective of this study is to find out the robustness
properties of the adaptive trimmed means in terms of efficiency, high
breakdown point and influence function. Specifically, it seeks to find
out the magnitude of the trimming proportion of the adaptive
trimmed mean which will yield efficient and robust estimates of the
parameter for data which follow a modified Weibull distribution with
parameter λ = 1/2 , where the trimming proportion is determined by a
ratio of two trimmed means defined as the tail length. Secondly, the
asymptotic properties of the tail length and the trimmed means are
also investigated. Finally, a comparison is made on the efficiency of
the adaptive trimmed means in terms of the standard deviation for the
trimming proportions and when these were fixed a “priori".
The asymptotic tail lengths defined as the ratio of two trimmed
means and the asymptotic variances were computed by using the
formulas derived. While the values of the standard deviations for the
derived tail lengths for data of size 40 simulated from a Weibull
distribution were computed for 100 iterations using a computer
program written in Pascal language.
The findings of the study revealed that the tail lengths of the
Weibull distribution increase in magnitudes as the trimming
proportions increase, the measure of the tail length and the adaptive
trimmed mean are asymptotically independent as the number of
observations n becomes very large or approaching infinity, the tail
length is asymptotically distributed as the ratio of two independent
normal random variables, and the asymptotic variances decrease as
the trimming proportions increase. The simulation study revealed
empirically that the standard error of the adaptive trimmed mean
using the ratio of tail lengths is relatively smaller for different values
of trimming proportions than its counterpart when the trimming
proportions were fixed a 'priori'.
Abstract: By the application of an improved back-propagation
neural network (BPNN), a model of current densities for a solid oxide
fuel cell (SOFC) with 10 layers is established in this study. To build
the learning data of BPNN, Taguchi orthogonal array is applied to
arrange the conditions of operating parameters, which totally 7 factors
act as the inputs of BPNN. Also, the average current densities
achieved by numerical method acts as the outputs of BPNN.
Comparing with the direct solution, the learning errors for all learning
data are smaller than 0.117%, and the predicting errors for 27
forecasting cases are less than 0.231%. The results show that the
presented model effectively builds a mathematical algorithm to predict
performance of a SOFC stack immediately in real time.
Also, the calculating algorithms are applied to proceed with the
optimization of the average current density for a SOFC stack. The
operating performance window of a SOFC stack is found to be
between 41137.11 and 53907.89. Furthermore, an inverse predicting
model of operating parameters of a SOFC stack is developed here by
the calculating algorithms of the improved BPNN, which is proved to
effectively predict operating parameters to achieve a desired
performance output of a SOFC stack.
Abstract: This paper explores the extent of the gap in poverty rates between immigrant and native households in Spanish regions and assess to what extent regional differences in individual and contextual characteristics can explain the divergences in such a gap. By using multilevel techniques and European Union Survey on Income and Living Conditions, we estimate immigrant households experiments an increase of 76 per cent in the odds of being poor compared with a native one when we control by individual variables. In relation to regional differences in the risk of poverty, regionallevel variables have higher effect in the reduction of these differences than individual variables.