Abstract: Solar panels that use photovoltaic (PV) cells are popular
for converting solar radiation into electricity. One of the major
problems impacting the performance of PV panels is the overheating
caused by excessive solar radiation and high ambient temperatures,
which degrades the efficiency of the PV panels remarkably. To
overcome this issue, an aluminum heat sink was used to dissipate
unwanted heat from PV cells. The dimensions of the heat sink were
determined considering the optimal fin spacing that fulfils hot climatic
conditions. In this study, the effects of cooling on the efficiency
and power output of a PV panel were studied experimentally. Two
PV modules were used: one without and one with a heat sink. The
experiments ran for 11 hours from 6:00 a.m. to 5:30 p.m. where
temperature readings in the rear and front of both PV modules were
recorded at an interval of 15 minutes using sensors and an Arduino
microprocessor. Results are recorded for both panels simultaneously
for analysis, temperate comparison, and for power and efficiency
calculations. A maximum increase in the solar to electrical conversion
efficiency of 35% and almost 55% in the power output were achieved
with the use of a heat sink, while temperatures at the front and back
of the panel were reduced by 9% and 11%, respectively.
Abstract: Two-wheel inverted pendulum robot (TWIPR) is designed with two-hub DC motors for human riding and motion control evaluation. In order to measure the tilt angle and angular velocity of the inverted pendulum robot, accelerometer and gyroscope sensors are chosen. The mobile robot’s moving position and velocity were estimated based on DC motor built in hall sensors. The control kernel of this electric mobile robot is designed with embedded Arduino Nano microprocessor. A handle bar was designed to work as steering mechanism. The intelligent model-free fuzzy sliding mode control (FSMC) was employed as the main control algorithm for this mobile robot motion monitoring with different control purpose adjustment. The intelligent controllers were designed for balance control, and moving speed control purposes of this robot under different operation conditions and the control performance were evaluated based on experimental results.
Abstract: Power management techniques are necessary to save power in the microprocessor. By changing the frequency and/or operating voltage of processor, DVFS can control power consumption. In this paper, we perform a case study to find optimal power state transition for DVFS. We propose the equation to find the optimal ratio between executions of states while taking into account the deadline of processing time and the power state transition delay overhead. The experiment is performed on the Cortex-M4 processor, and average 6.5% power saving is observed when DVFS is applied under the deadline condition.
Abstract: An adder is one of the most integral component of a digital system like a digital signal processor or a microprocessor. Being an extremely computationally intensive part of a system, the optimization for speed and power consumption of the adder is of prime importance. In this paper we have designed a 1 bit full adder cell based on dynamic TSPC logic to achieve high speed operation. A high threshold voltage sleep transistor is used to reduce the static power dissipation in standby mode. The circuit is designed and simulated in TSPICE using TSMC 180nm CMOS process. Average power consumption, delay and power-delay product is measured which showed considerable improvement in performance over the existing full adder designs.
Abstract: Conventional approaches in the implementation of logic programming applications on embedded systems are solely of software nature. As a consequence, a compiler is needed that transforms the initial declarative logic program to its equivalent procedural one, to be programmed to the microprocessor. This approach increases the complexity of the final implementation and reduces the overall system's performance. On the contrary, presenting hardware implementations which are only capable of supporting logic programs prevents their use in applications where logic programs need to be intertwined with traditional procedural ones, for a specific application. We exploit HW/SW codesign methods to present a microprocessor, capable of supporting hybrid applications using both programming approaches. We take advantage of the close relationship between attribute grammar (AG) evaluation and knowledge engineering methods to present a programmable hardware parser that performs logic derivations and combine it with an extension of a conventional RISC microprocessor that performs the unification process to report the success or failure of those derivations. The extended RISC microprocessor is still capable of executing conventional procedural programs, thus hybrid applications can be implemented. The presented implementation is programmable, supports the execution of hybrid applications, increases the performance of logic derivations (experimental analysis yields an approximate 1000% increase in performance) and reduces the complexity of the final implemented code. The proposed hardware design is supported by a proposed extended C-language called C-AG.
Abstract: A low cost Short Message System (SMS) based Home security system equipped with motion, smoke, temperature, humidity and light sensors has been studied and tested. The sensors are controlled by a microprocessor PIC 18F4520 through the SMS having password protection code for the secure operation. The user is able to switch light and the appliances and get instant feedback. Also in cases of emergencies such as fire or robbery the system will send alert message to occupant and relevant civil authorities. The operation of the home security has been tested on Vodafone- Fiji network and Digicel Fiji Network for emergency and feedback responses for 25 samples. The experiment showed that it takes about 8-10s for the security system to respond in case of emergency. It takes about 18-22s for the occupant to switch and monitor lights and appliances and then get feedback depending upon the network traffic.
Abstract: This paper presents a 24 watts SEPIC converter design
and control using microprocessor. SEPIC converter has advantages of
a wide input range and miniaturization caused by the low stress at
elements. There is also an advantage that the input and output are
isolated in MOSFET-off state. This paper presents the PID control
through the SEPIC converter transfer function using a DSP and the
protective circuit for fuel cell from the over-current and
inverse-voltage by using the characteristic of SEPIC converter. Then it
derives them through the experiments.