Abstract: Bandwidth allocation in wired network is less complex
and to allocate bandwidth in wireless networks is complex and
challenging, due to the mobility of source end system.This paper
proposes a new approach to bandwidth allocation to higher and lower
priority mobile nodes.In our proposal bandwidth allocation to new
mobile node is based on bandwidth utilization of existing mobile
nodes.The first section of the paper focuses on introduction to
bandwidth allocation in wireless networks and presents the existing
solutions available for allocation of bandwidth. The second section
proposes the new solution for the bandwidth allocation to higher and
lower priority nodes. Finally this paper ends with the analytical
evaluation of the proposed solution.
Abstract: This paper reports on the theoretical performance
analysis of the 1.3 μm In0.42Ga0.58As /In0.26Ga0.74As multiple quantum
well (MQW) vertical cavity surface emitting laser (VCSEL) on the
ternary In0.31Ga0.69As substrate. The output power of 2.2 mW has
been obtained at room temperature for 7.5 mA injection current. The
material gain has been estimated to be ~3156 cm-1 at room
temperature with the injection carrier concentration of 2×1017 cm-3.
The modulation bandwidth of this laser is measured to be 9.34 GHz
at room temperature for the biasing current of 2 mA above the
threshold value. The outcomes reveal that the proposed InGaAsbased
MQW laser is the promising one for optical communication
system.
Abstract: The main objectives of this study are to inspect and
identify any damage of jaimusi highway prestressed concrete bridge
after repair and strengthening of damaged structural members and to
evaluate the performance of the bridge structural members by
adopting static load test. Inspection program after repair and
strengthening includes identifying and evaluating the structural
members of bridge such as T-shape cantilever structure, hanging
beams, corbels, external tendons, anchor beams, sticking steel plate,
and piers. The results of inspection show that the overall state of the
bridge structural member after repair and strengthening is good. The
results of rebound test of concrete strength show that the average
strength of concrete is 46.31Mpa. Whereas, the average value of
concrete strength of anchor beam is 49.82Mpa. According to the
results of static load test, the experimental values are less than
theoretical values of internal forces, deflection, and strain, indicating
that the stiffness of the experimental structure, overall deformation
and integrity satisfy the designed standard and the working
performance is good, and the undertaking capacity has a certain
surplus. There is not visible change in the length and width of cracks
and there are not new cracks under experimental load.
Abstract: In this paper we propose the study of a centrifugal pump control system driven by a three-phase induction motor, which is supplied by a PhotoVoltaic PV generator. The system includes solar panel, a DC / DC converter equipped with its MPPT control, a voltage inverter to three-phase Pulse Width Modulation - PWM and a centrifugal pump driven by a three phase induction motor. In order to control the flow of the centrifugal pump, a Direct Torque Control - DTC of the induction machine is used. To illustrate the performances of the control, simulation results are carried out using Matlab/Simulink.
Abstract: Physical and mechanical properties of Russian olive
fruits were measured at moisture content of 14.43% w.b. The results
revealed that the mean length, width and thickness of Russian olive
fruits were 20.72, 15.73 and 14.69mm, respectively. Mean mass and
volume of Russian olive fruits were measured as 1.45 g and 2.55 cm3,
respectively. The sphericity, aspect ratio and surface area were
calculated as 0.81, 0.72 and 8.96 cm2, respectively, while arithmetic
mean diameter, geometric mean diameter and equivalent diameter of
Russian olive fruits were 17.05, 16.83 and 16.84 mm, respectively.
Whole fruit density, bulk density and porosity of jujube fruits were
measured and found to be 1.01 g/cm3, 0.29 g/cm3 and 69.5%,
respectively. The values of static coefficient of friction on three
surfaces of glass, galvanized iron and plywood were 0.35, 0.36 and
0.43, respectively. The skin color (L*, a*, b*) varied from 9.92 to
16.08; 2.04 to 3.91 and 1.12 to 3.83, respectively. The values of
rupture force, deformation, energy absorbed and hardness were found
to be between 12.14-16.85 N, 2.16-4.25 mm, 3.42-6.99 N mm and
17.1-23.85 N/mm.
Abstract: Guaranteeing the availability of the required parts at
the scheduled time represents a key logistical challenge. This is
especially important when several parts are required together. This
article describes a tool that supports the positioning in the area of
conflict between low stock costs and a high service level for a
consumer.
Abstract: Cryptographic algorithms play a crucial role in the
information society by providing protection from unauthorized
access to sensitive data. It is clear that information technology will
become increasingly pervasive, Hence we can expect the emergence
of ubiquitous or pervasive computing, ambient intelligence. These
new environments and applications will present new security
challenges, and there is no doubt that cryptographic algorithms and
protocols will form a part of the solution. The efficiency of a public
key cryptosystem is mainly measured in computational overheads,
key size and bandwidth. In particular the RSA algorithm is used in
many applications for providing the security. Although the security
of RSA is beyond doubt, the evolution in computing power has
caused a growth in the necessary key length. The fact that most chips
on smart cards can-t process key extending 1024 bit shows that there
is need for alternative. NTRU is such an alternative and it is a
collection of mathematical algorithm based on manipulating lists of
very small integers and polynomials. This allows NTRU to high
speeds with the use of minimal computing power. NTRU (Nth degree
Truncated Polynomial Ring Unit) is the first secure public key
cryptosystem not based on factorization or discrete logarithm
problem. This means that given sufficient computational resources
and time, an adversary, should not be able to break the key. The
multi-party communication and requirement of optimal resource
utilization necessitated the need for the present day demand of
applications that need security enforcement technique .and can be
enhanced with high-end computing. This has promoted us to develop
high-performance NTRU schemes using approaches such as the use
of high-end computing hardware. Peer-to-peer (P2P) or enterprise
grids are proven as one of the approaches for developing high-end
computing systems. By utilizing them one can improve the
performance of NTRU through parallel execution. In this paper we
propose and develop an application for NTRU using enterprise grid
middleware called Alchemi. An analysis and comparison of its
performance for various text files is presented.
Abstract: The computer modeling is carried out for parameter of
sensitivity of optoelectronic chemical and biosensors, using
phenomena of surface plasmon resonance (SPR). The physical model
of SPR-sensor-s is described with (or without) of modifications of
sensitive gold film surface by a dielectric layer. The variants of
increasing of sensitivity for SPR-biosensors, constructed on the
principle gold – dielectric – biomolecular layer are considered. Two
methods of mathematical treatment of SPR-curve are compared –
traditional, with estimation of sensor-s response as shift of the SPRcurve
minimum and proposed, for system with dielectric layer, using
calculating of the derivative in the point of SPR-curve half-width.
Abstract: Interactive push VOD system is a new kind of system
that incorporates push technology and interactive technique. It can
push movies to users at high speeds at off-peak hours for optimal
network usage so as to save bandwidth. This paper presents effective
software-based solution for processing mass downstream data at
terminals of interactive push VOD system, where the service can
download movie according to a viewer-s selection. The downstream
data is divided into two catalogs: (1) the carousel data delivered
according to DSM-CC protocol; (2) IP data delivered according to
Euro-DOCSIS protocol. In order to accelerate download speed and
reduce data loss rate at terminals, this software strategy introduces
caching, multi-thread and resuming mechanisms. The experiments
demonstrate advantages of the software-based solution.
Abstract: This paper deals with an on-line identification method
of continuous-time Hammerstein systems by using the radial basis
function (RBF) networks and immune algorithm (IA). An unknown
nonlinear static part to be estimated is approximately represented
by the RBF network. The IA is efficiently combined with the
recursive least-squares (RLS) method. The objective function for the
identification is regarded as the antigen. The candidates of the RBF
parameters such as the centers and widths are coded into binary bit
strings as the antibodies and searched by the IA. On the other hand,
the candidates of both the weighting parameters of the RBF network
and the system parameters of the linear dynamic part are updated
by the RLS method. Simulation results are shown to illustrate the
proposed method.
Abstract: this paper presented a survey analysis subjected on
network bandwidth management from published papers referred in
IEEE Explorer database in three years from 2009 to 2011. Network
Bandwidth Management is discussed in today-s issues for computer
engineering applications and systems. Detailed comparison is
presented between published papers to look further in the IP based
network critical research area for network bandwidth management.
Important information such as the network focus area, a few
modeling in the IP Based Network and filtering or scheduling used in
the network applications layer is presented. Many researches on
bandwidth management have been done in the broad network area
but fewer are done in IP Based network specifically at the
applications network layer. A few researches has contributed new
scheme or enhanced modeling but still the issue of bandwidth
management still arise at the applications network layer. This survey
is taken as a basic research towards implementations of network
bandwidth management technique, new framework model and
scheduling scheme or algorithm in an IP Based network which will
focus in a control bandwidth mechanism in prioritizing the network
traffic the applications layer.
Abstract: Some physical properties of musk lime (Citrus
microcarpa) were determined in this study. The average moisture
content (wet basis) of the fruit was found to be 85.10 (±0.72) %. The
mean of length, width and thickness of the fruit was 26.36 (±0.97),
26.40 (±1.04) and 25.26 (±0.94) mm respectively. The average value
for geometric mean diameter, sphericity, aspect ratio, mass, surface
area, volume, true density, bulk density and porosity was 26.00
(±0.82) mm, 98.67 (±2.04) %, 100.23 (±3.28) %, 10.007 (±0.878) g,
2125.07 (±133.93) mm2, 8800.00 (±731.82) mm3, 1002.87 (±39.16)
kgm-3, 501.70 (±22.58) kgm-3 and 49.89 (±3.15) % respectively.
The coefficient of static friction on four types of structural surface
was found to be varying from 0.238 (±0.025) for glass to 0.247
(±0.024) for steel surface.
Abstract: In this research work, investigations are carried out on
Continuous Wave (CW) Nd:YAG laser welding system after
preliminary experimentation to understand the influencing parameters
associated with laser welding of AISI 304. The experimental
procedure involves a series of laser welding trials on AISI 304
stainless steel sheets with various combinations of process parameters
like beam power, beam incident angle and beam incident angle. An
industrial 2 kW CW Nd:YAG laser system, available at Welding
Research Institute (WRI), BHEL Tiruchirappalli, is used for
conducting the welding trials for this research. After proper tuning of
laser beam, laser welding experiments are conducted on AISI 304
grade sheets to evaluate the influence of various input parameters on
weld bead geometry i.e. bead width (BW) and depth of penetration
(DOP). From the laser welding results, it is noticed that the beam
power and welding speed are the two influencing parameters on
depth and width of the bead. Three dimensional finite element
simulation of high density heat source have been performed for laser
welding technique using finite element code ANSYS for predicting
the temperature profile of laser beam heat source on AISI 304
stainless steel sheets. The temperature dependent material properties
for AISI 304 stainless steel are taken into account in the simulation,
which has a great influence in computing the temperature profiles.
The latent heat of fusion is considered by the thermal enthalpy of
material for calculation of phase transition problem. A Gaussian
distribution of heat flux using a moving heat source with a conical
shape is used for analyzing the temperature profiles. Experimental
and simulated values for weld bead profiles are analyzed for stainless
steel material for different beam power, welding speed and beam
incident angle. The results obtained from the simulation are
compared with those from the experimental data and it is observed
that the results of numerical analysis (FEM) are in good agreement
with experimental results, with an overall percentage of error
estimated to be within ±6%.
Abstract: For high-speed control of robots, a good knowledge of system modelling is necessary to obtain the desired bandwidth. In this paper, we present a cartesian robot with a pan/tilt unit in end-effector (5 dof). This robot is implemented with powerful direct drive AC induction machines. The dynamic model, parameter identification and model validation of the robot are studied (including actuators). This work considers the cartesian robot coupled and non linear (contrary to normal considerations for this type of robots). The mechanical and control architecture proposed in this paper is efficient for industrial and research application in which high speed, well known model and very high accuracy are required.
Abstract: In this paper the reference current for Voltage Source
Converter (VSC) of the Shunt Active Power Filter (SAPF) is
generated using Synchronous Reference Frame method,
incorporating the PI controller with anti-windup scheme. The
proposed method improves the harmonic filtering by compensating
the winding up phenomenon caused by the integral term of the PI
controller.
Using Reference Frame Transformation, the current is transformed
from om a - b - c stationery frame to rotating 0 - d - q frame. Using
the PI controller, the current in the 0 - d - q frame is controlled to
get the desired reference signal. A controller with integral action
combined with an actuator that becomes saturated can give some
undesirable effects. If the control error is so large that the integrator
saturates the actuator, the feedback path becomes ineffective because
the actuator will remain saturated even if the process output changes.
The integrator being an unstable system may then integrate to a very
large value, the phenomenon known as integrator windup.
Implementing the integrator anti-windup circuit turns off the
integrator action when the actuator saturates, hence improving the
performance of the SAPF and dynamically compensating harmonics
in the power network. In this paper the system performance is
examined with Shunt Active Power Filter simulation model.
Abstract: Paper presents simple sixport principle and its frequency bandwidth. The novel multisixport approach is presented with its possibilities, typical parameters and frequency bandwidth. Practical implementation is shown with its measurement parameters and calibration. The bandwidth circa 1:100 is obtained.
Abstract: In the recent years multimedia traffic and in particular
VoIP services are growing dramatically. We present a new algorithm
to control the resource utilization and to optimize the voice codec
selection during SIP call setup on behalf of the traffic condition
estimated on the network path.
The most suitable methodologies and the tools that perform realtime
evaluation of the available bandwidth on a network path have
been integrated with our proposed algorithm: this selects the best
codec for a VoIP call in function of the instantaneous available
bandwidth on the path. The algorithm does not require any explicit
feedback from the network, and this makes it easily deployable over
the Internet. We have also performed intensive tests on real network
scenarios with a software prototype, verifying the algorithm
efficiency with different network topologies and traffic patterns
between two SIP PBXs.
The promising results obtained during the experimental validation
of the algorithm are now the basis for the extension towards a larger
set of multimedia services and the integration of our methodology
with existing PBX appliances.
Abstract: In this paper we present a soft timing phase estimation (STPE) method for wireless mobile receivers operating in low signal to noise ratios (SNRs). Discrete Polyphase Matched (DPM) filters, a Log-maximum a posterior probability (MAP) and/or a Soft-output Viterbi algorithm (SOVA) are combined to derive a new timing recovery (TR) scheme. We apply this scheme to wireless cellular communication system model that comprises of a raised cosine filter (RCF), a bit-interleaved turbo-coded multi-level modulation (BITMM) scheme and the channel is assumed to be memory-less. Furthermore, no clock signals are transmitted to the receiver contrary to the classical data aided (DA) models. This new model ensures that both the bandwidth and power of the communication system is conserved. However, the computational complexity of ideal turbo synchronization is increased by 50%. Several simulation tests on bit error rate (BER) and block error rate (BLER) versus low SNR reveal that the proposed iterative soft timing recovery (ISTR) scheme outperforms the conventional schemes.
Abstract: Among other factors that characterize satellite communication
channels is their high bit error rate. We present a system for
still image transmission over noisy satellite channels. The system
couples image compression together with error control codes to
improve the received image quality while maintaining its bandwidth
requirements. The proposed system is tested using a high resolution
satellite imagery simulated over the Rician fading channel. Evaluation
results show improvement in overall system including image quality
and bandwidth requirements compared to similar systems with different
coding schemes.
Abstract: Equilibrium and stability equations of a thin rectangular plate with length a, width b, and thickness h(x)=C1x+C2, made of functionally graded materials under thermal loads are derived based on the first order shear deformation theory. It is assumed that the material properties vary as a power form of thickness coordinate variable z. The derived equilibrium and buckling equations are then solved analytically for a plate with simply supported boundary conditions. One type of thermal loading, uniform temperature rise and gradient through the thickness are considered, and the buckling temperatures are derived. The influences of the plate aspect ratio, the relative thickness, the gradient index and the transverse shear on buckling temperature difference are all discussed.