Abstract: In this paper the modeling and analysis of Space
Vector Pulse Width Modulation (SVPWM) based Dynamic Voltage
Restorer (DVR) using PSCAD/EMTDC software will be presented in
details. The simulation includes full modeling of the SVPWM
technique used to control the DVR inverter. A test power system
composed of three phase voltage source, sag generator, DVR and
three phase resistive load is used to demonstrate restoration capability
of the DVR. The simulation results of the presented DVR proved
excellent voltage sag mitigation to protect sensitive loads.
Abstract: Detection, feature extraction and pose estimation of
people in images and video is made challenging by the variability of
human appearance, the complexity of natural scenes and the high
dimensionality of articulated body models and also the important
field in Image, Signal and Vision Computing in recent years. In this
paper, four types of people in 2D dimension image will be tested and
proposed. The system will extract the size and the advantage of them
(such as: tall fat, short fat, tall thin and short thin) from image. Fat
and thin, according to their result from the human body that has been
extract from image, will be obtained. Also the system extract every
size of human body such as length, width and shown them in output.
Abstract: This study was conducted published to investigate
there liability of the equation pressure-impulse (PI) reinforced
concrete column inprevious studies. Equation involves three different
levels of damage criteria known as D =0. 2, D =0. 5 and D =0. 8.The
damage criteria known as a minor when 0-0.2, 0.2-0.5is known as
moderate damage, high damage known as 0.5-0.8, and 0.8-1 of the
structure is considered a failure. In this study, two types of reliability
analyzes conducted. First, using pressure-impulse equation with
different parameters. The parameters involved are the concrete
strength, depth, width, and height column, the ratio of longitudinal
reinforcement and transverse reinforcement ratio. In the first analysis
of the reliability of this new equation is derived to improve the
previous equations. The second reliability analysis involves three
types of columns used to derive the PI curve diagram using the
derived equation to compare with the equation derived from other
researchers and graph minimum standoff versus weapon yield
Federal Emergency Management Agency (FEMA). The results
showed that the derived equation is more accurate with FEMA
standards than previous researchers.
Abstract: This paper uses the radial basis function neural
network (RBFNN) for system identification of nonlinear systems.
Five nonlinear systems are used to examine the activity of RBFNN in
system modeling of nonlinear systems; the five nonlinear systems are
dual tank system, single tank system, DC motor system, and two
academic models. The feed forward method is considered in this
work for modelling the non-linear dynamic models, where the KMeans
clustering algorithm used in this paper to select the centers of
radial basis function network, because it is reliable, offers fast
convergence and can handle large data sets. The least mean square
method is used to adjust the weights to the output layer, and
Euclidean distance method used to measure the width of the Gaussian
function.
Abstract: Nowadays Multilevel inverters are widely using in various applications. Modulation strategy at fundamental switching frequency like, SHEPWM is prominent technique to eliminate lower order of harmonics with less switching losses and better harmonic profile. The equations which are formed by SHE are highly nonlinear transcendental in nature, there may exist single, multiple or even no solutions for a particular MI. However, some loads such as electrical drives, it is required to operate in whole range of MI. In order to solve SHE equations for whole range of MI, intelligent techniques are well suited to solve equations so as to produce lest %THDV. Hence, this paper uses Continuous genetic algorithm for minimising harmonics. This paper also presents wavelet based analysis of harmonics. The developed algorithm is simulated and %THD from FFT analysis and Wavelet analysis are compared. MATLAB programming environment and SIMULINK models are used whenever necessary.
Abstract: Multilevel inverters supplied from equal and constant
dc sources almost don-t exist in practical applications. The variation
of the dc sources affects the values of the switching angles required
for each specific harmonic profile, as well as increases the difficulty
of the harmonic elimination-s equations. This paper presents an
extremely fast optimal solution of harmonic elimination of multilevel
inverters with non-equal dc sources using Tanaka's fuzzy linear
regression formulation. A set of mathematical equations describing
the general output waveform of the multilevel inverter with nonequal
dc sources is formulated. Fuzzy linear regression is then
employed to compute the optimal solution set of switching angles.
Abstract: This paper is a simple and systematic approaches to the design and analysis a pulse width modulation (PWM) based sliding mode controller for buck DC-DC Converters. Various aspects of the design, including the practical problems and the proposed solutions, are detailed. However, these control strategies can't compensate for large load current and input voltage variations. In this paper, a new control strategy by compromising both schemes advantages and avoiding their drawbacks is proposed, analyzed and simulated.
Abstract: This paper presents the theoretical investigation of a
slotted patch antenna. The main objective of proposed work is to
obtain a large bandwidth antenna with reduced size. The antenna has
a compact size of 21.1mm x 20.25mm x 8.5mm. Two designs with
minor variation are studied which provide wide impedance
bandwidths of 24.056% and 25.63% respectively with the use of
parasitic elements when excited by a probe feed. The advantages of
this configuration are its compact size and the wide range of
frequencies covered. A parametric study is also conducted to
investigate the characteristics of the antenna under different
conditions. The measured return loss and radiation pattern indicate
the suitability of this design for WLAN applications, namely, Wi-
Max, 802.11a/b/g and ISM bands.
Abstract: It is necessary to evaluate the bridges conditions and
strengthen bridges or parts of them. The reinforcement necessary due
to some reasons can be summarized as: First, a changing in use of
bridge could produce internal forces in a part of structural which
exceed the existing cross-sectional capacity. Second, bridges may
also need reinforcement because damage due to external factors
which reduced the cross-sectional resistance to external loads. One of
other factors could listed here its misdesign in some details, like
safety of bridge or part of its.This article identify the design demands
of Qing Shan bridge located in is in Heilongjiang Province He gang -
Nen Jiang Road 303 provincial highway, Wudalianchi area, China, is
an important bridge in the urban areas. The investigation program
was include the observation and evaluate the damage in T- section
concrete beams , prestressed concrete box girder bridges section in
additional evaluate the whole state of bridge includes the pier ,
abutments , bridge decks, wings , bearing and capping beam, joints,
........etc. The test results show that the bridges in general structural
condition are good. T beam span No 10 were observed, crack
extended upward along the ribbed T beam, and continue to the T
beam flange. Crack width varying between 0.1mm to 0.4mm, the
maximum about 0.4mm. The bridge needs to be improved flexural
bending strength especially at for T beam section.
Abstract: Bluetooth is a personal wireless communication
technology and is being applied in many scenarios. It is an emerging
standard for short range, low cost, low power wireless access
technology. Current existing MAC (Medium Access Control)
scheduling schemes only provide best-effort service for all masterslave
connections. It is very challenging to provide QoS (Quality of
Service) support for different connections due to the feature of
Master Driven TDD (Time Division Duplex). However, there is no
solution available to support both delay and bandwidth guarantees
required by real time applications. This paper addresses the issue of
how to enhance QoS support in a Bluetooth piconet. The Bluetooth
specification proposes a Round Robin scheduler as possible solution
for scheduling the transmissions in a Bluetooth Piconet. We propose
an algorithm which will reduce the bandwidth waste and enhance the
efficiency of network. We define token counters to estimate traffic of
real-time slaves. To increase bandwidth utilization, a back-off
mechanism is then presented for best-effort slaves to decrease the
frequency of polling idle slaves. Simulation results demonstrate that
our scheme achieves better performance over the Round Robin
scheduling.
Abstract: The Platform Screen Doors improve Indoor Air Quality
(IAQ) in the subway station; however, and the air quality is degraded
in the subway tunnel. CO2 concentration and indoor particulate matter
value are high in the tunnel. The IAQ level in subway tunnel degrades
by increasing the train movements. Air-curtain installation reduces
dusts, particles and moving toxic smokes and permits traffic by
generating virtual wall. The ventilation systems of the subway tunnel
need improvements to have better air-quality. Numerical analyses
might be effective tools analyze the flowfield inside the air-curtain
installed subway tunnel. The ANSYS CFX software is used for steady
computations of the airflow inside the tunnel. The single-track subway
tunnel has the natural shaft, the mechanical shaft, and the PSDs
installed stations. The height and width of the tunnel are 6.0 m and 4.0
m respectively. The tunnel is 400 m long and the air-curtain is installed
at the top of the tunnel. The thickness and the width of the air-curtain
are 0.08 m and 4 m respectively. The velocity of the air-curtain
changes between 20 - 30 m/s. Three cases are analyzed depending on
the installing location of the air-curtain. The discharged-air through
the natural shafts increases as the velocity of the air-curtain increases
when the air-curtain is installed between the mechanical and the
natural shafts. The pollutant-air is exhausted by the mechanical and the
natural shafts and remained air is pushed toward tunnel end. The
discharged-air through the natural shaft is low when the air-curtain
installed before the natural shaft. The mass flow rate decreases in the
tunnel after the mechanical shaft as the air-curtain velocity increases.
The computational results of the air-curtain installed tunnel become
basis for the optimum design study. The air-curtain installing location
is chosen between the mechanical and the natural shafts. The velocity
of the air-curtain is fixed as 25 m/s. The thickness and the blowing
angles of the air-curtain are the design variables for the optimum
design study. The object function of the design optimization is
maximizing the discharged air through the natural shaft.
Abstract: Sedimentation in reservoirs and the corresponding
loss of storage capacity is one of the most serious problems in dam
engineering. Pressurized flushing, a way to remove sediments from the reservoir, is flushing under a pressurized flow condition and
nearly constant water level. Pressurized flushing has only local
effects around the outlet. Sediment in the vicinity of the outlet openings is scoured and a funnel shaped crater is created. In this study, the temporal development of flushing cone under various
hydraulic conditions was studied experimentally. Time variations of
parameters such as maximum length and width of flushing and also
depth of scouring cone was measured. Results indicated that an
increase in flow velocity (and consequently in Froude number)
established new hydraulically conditions for flushing mechanism and
so a sudden growth was observed in the amount of sediment released
and also scouring dimenssions. In addition, a set of nondimensional
relationships were identified for temporal variations of flushing scour
dimenssions, which can eventuallt be used to estimate the development of flushing cone.
Abstract: ECG analysis method was developed using ROC
analysis of PVC detecting algorithm. ECG signal of MIT-BIH
arrhythmia database was analyzed by MATLAB. First of all, the
baseline was removed by median filter to preprocess the ECG signal.
R peaks were detected for ECG analysis method, and normal VCG
was extracted for VCG analysis method. Four PVC detecting
algorithm was analyzed by ROC curve, which parameters are
maximum amplitude of QRS complex, width of QRS complex, r-r
interval and geometric mean of VCG. To set cut-off value of
parameters, ROC curve was estimated by true-positive rate
(sensitivity) and false-positive rate. sensitivity and false negative rate
(specificity) of ROC curve calculated, and ECG was analyzed using
cut-off value which was estimated from ROC curve. As a result, PVC
detecting algorithm of VCG geometric mean have high availability,
and PVC could be detected more accurately with amplitude and width
of QRS complex.
Abstract: In this paper, a new BiCMOS CCII and CCCII,
capable of operate at ±0.5V and having wide dynamic range with
achieved bandwidth of 480MHz and 430MHz respectively have been
proposed. The structures have been found to be insensitive to the
threshold voltage variations. The proposed circuits are suitable for
implementation using 0.25μm BiCMOS technology. Pspice
simulations confirm the performance of the proposed structures.
Abstract: This paper is a description approach to predict
incoming and outgoing data rate in network system by using
association rule discover, which is one of the data mining
techniques. Information of incoming and outgoing data in each
times and network bandwidth are network performance
parameters, which needed to solve in the traffic problem. Since
congestion and data loss are important network problems. The result
of this technique can predicted future network traffic. In addition,
this research is useful for network routing selection and network
performance improvement.
Abstract: The major part of light weight timber constructions
consists of insulation. Mineral wool is the most commonly used
insulation due to its cost efficiency and easy handling. The fiber
orientation and porosity of this insulation material enables flowthrough.
The air flow resistance is low. If leakage occurs in the
insulated bay section, the convective flow may cause energy losses
and infiltration of the exterior wall with moisture and particles. In
particular the infiltrated moisture may lead to thermal bridges and
growth of health endangering mould and mildew. In order to prevent
this problem, different numerical calculation models have been
developed. All models developed so far have a potential for
completion. The implementation of the flow-through properties of
mineral wool insulation may help to improve the existing models.
Assuming that the real pressure difference between interior and
exterior surface is larger than the prescribed pressure difference in the
standard test procedure for mineral wool ISO 9053 / EN 29053,
measurements were performed using the measurement setup for
research on convective moisture transfer “MSRCMT".
These measurements show, that structural inhomogeneities of
mineral wool effect the permeability only at higher pressure
differences, as applied in MSRCMT. Additional microscopic
investigations show, that the location of a leak within the
construction has a crucial influence on the air flow-through and the
infiltration rate. The results clearly indicate that the empirical values
for the acoustic resistance of mineral wool should not be used for the
calculation of convective transfer mechanisms.
Abstract: This paper presents a experiment to estimate the
influences of cutting conditions in microstructure changes of
machining austenitic 304 stainless steel, especially for wear insert. The
wear insert were prefabricated with a width of 0.5 mm. And the forces,
temperature distribution, RS, and microstructure changes were
measured by force dynamometer, infrared thermal camera, X-ray
diffraction, XRD, SEM, respectively. The results told that the different
combinations of machining condition have a significant influence on
machined surface microstructure changes. In addition to that, the
ANOVA and AOMwere used to tell the different influences of cutting
speed, feed rate, and wear insert.
Abstract: Due to the complex network architecture, the mobile
adhoc network-s multihop feature gives additional problems to the
users. When the traffic load at each node gets increased, the
additional contention due its traffic pattern might cause the nodes
which are close to destination to starve the nodes more away from the
destination and also the capacity of network is unable to satisfy the
total user-s demand which results in an unfairness problem. In this
paper, we propose to create an algorithm to compute the optimal
MAC-layer bandwidth assigned to each flow in the network. The
bottleneck links contention area determines the fair time share which
is necessary to calculate the maximum allowed transmission rate used
by each flow. To completely utilize the network resources, we
compute two optimal rates namely, the maximum fair share and
minimum fair share. We use the maximum fair share achieved in
order to limit the input rate of those flows which crosses the
bottleneck links contention area when the flows that are not allocated
to the optimal transmission rate and calculate the following highest
fair share. Through simulation results, we show that the proposed
protocol achieves improved fair share and throughput with reduced
delay.
Abstract: This paper describes a low-voltage and low-power
channel selection analog front end with continuous-time low pass
filters and highly linear programmable gain amplifier (PGA). The
filters were realized as balanced Gm-C biquadratic filters to achieve a
low current consumption. High linearity and a constant wide
bandwidth are achieved by using a new transconductance (Gm) cell.
The PGA has a voltage gain varying from 0 to 65dB, while
maintaining a constant bandwidth. A filter tuning circuit that requires
an accurate time base but no external components is presented.
With a 1-Vrms differential input and output, the filter achieves
-85dB THD and a 78dB signal-to-noise ratio. Both the filter and PGA
were implemented in a 0.18um 1P6M n-well CMOS process. They
consume 3.2mW from a 1.8V power supply and occupy an area of
0.19mm2.