Abstract: Hepatocellular carcinoma, also called hepatoma, most
commonly appears in a patient with chronic viral hepatitis. In
patients with a higher suspicion of HCC, such as small or subtle
rising of serum enzymes levels, the best method of diagnosis
involves a CT scan of the abdomen, but only at high cost. The aim of
this study was to increase the ability of the physician to early detect
HCC, using a probabilistic neural network-based approach, in order
to save time and hospital resources.
Abstract: Typically thermal power plants are located near to
surface coal mines that produce huge amount of fly ash as a waste
byproduct. Disposal of fly ash causes significant economic and
environmental problems. Now-a-days, research is going on for bulk
utilization of fly ash. In order to increase its percentage utilization, an
investigation was carried out to evaluate its potential for haul road
construction. This paper presents the laboratory California bearing
ratio (CBR) tests and evaluates the effect of lime on CBR behavior of
fly ash - mine overburden mixes. Tests were performed with different
percentages of lime (2%, 3%, 6%, and 9%). The results show that the
increase in bearing ratio of fly ash-overburden mixes was achieved
by lime treatment. Scanning electron microscopy (SEM) analyses
were conducted on 28 days cured specimens. The SEM study showed
that the bearing ratio development is related to the microstructural
development.
Abstract: The nonlinear damping behavior is usually ignored in
the design of a miniature moving-coil loudspeaker. But when the
loudspeaker operated in air, the damping parameter varies with the
voice-coil displacement corresponding due to viscous air flow. The
present paper presents an identification model as inverse problem to
identify the nonlinear damping parameter in the lumped parameter
model for the loudspeaker. Theoretical results for the nonlinear
damping are verified by using laser displacement measurement
scanner. These results indicate that the damping parameter has the
greatly different nonlinearity between in air and vacuum. It is believed
that the results of the present work can be applied in diagnosis and
sound quality improvement of a miniature loudspeaker.
Abstract: In this paper, the bond strength of thermal spray
coatings in high speed shafts has been studied. The metallurgical and
mechanical studies has been made on the coated samples and shaft
using optical microscopy, scanning electron microscopy (SEM).
Abstract: Laser Metal Deposition (LMD) is an additive manufacturing process with capabilities that include: producing new
part directly from 3 Dimensional Computer Aided Design (3D CAD)
model, building new part on the existing old component and repairing an existing high valued component parts that would have
been discarded in the past. With all these capabilities and its advantages over other additive manufacturing techniques, the
underlying physics of the LMD process is yet to be fully understood probably because of high interaction between the processing
parameters and studying many parameters at the same time makes it
further complex to understand. In this study, the effect of laser power
and powder flow rate on physical properties (deposition height and
deposition width), metallurgical property (microstructure) and
mechanical (microhardness) properties on laser deposited most
widely used aerospace alloy are studied. Also, because the Ti6Al4V
is very expensive, and LMD is capable of reducing buy-to-fly ratio
of aerospace parts, the material utilization efficiency is also studied.
Four sets of experiments were performed and repeated to establish repeatability using laser power of 1.8 kW and 3.0 kW, powder flow
rate of 2.88 g/min and 5.67 g/min, and keeping the gas flow rate and
scanning speed constant at 2 l/min and 0.005 m/s respectively. The
deposition height / width are found to increase with increase in laser
power and increase in powder flow rate. The material utilization is favoured by higher power while higher powder flow rate reduces
material utilization. The results are presented and fully discussed.
Abstract: Using of natural lighting has come into prominence in
constructed buildings, especially in last ten years, under scope of
energy efficiency. Natural lighting methods are one of the methods
that aim to take advantage of day light in maximum level and
decrease using of artificial lighting. Increasing of day light amount in
buildings by using suitable methods will give optimum result in
terms of comfort and energy saving when the daylight-artificial light
integration is ensured with a suitable control system. Using of natural
light in places that require lighting will ensure energy saving in great
extent. With this study, it is aimed to save energy used for purpose of
lighting. Under this scope, lighting of a scanning laboratory of a
hospital was realized by using a lighting automation containing
natural and artificial lighting. In natural lighting, light pipes were
used and in artificial lighting, dimmable power LED modules were
used. Necessity of lighting was followed with motion sensors. The
lighting automation containing natural and artificial light was ensured
with fuzzy logic control. At the scanning laboratory where this
application was realized, energy saving in lighting was obtained.
Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: A novel nanofinishing process using improved ball
end magnetorheological (MR) finishing tool was developed for finishing of flat as well as 3D surfaces of ferromagnetic and non ferromagnetic workpieces. In this process a magnetically controlled
ball end of smart MR polishing fluid is generated at the tip surface of
the tool which is used as a finishing medium and it is guided to
follow the surface to be finished through computer controlled 3-axes
motion controller. The experiments were performed on ferromagnetic
workpiece surface in the developed MR finishing setup to study the effect of finishing time on final surface roughness. The performance
of present finishing process on final finished surface roughness was studied. The surface morphology was observed under scanning
electron microscopy and atomic force microscope. The final surface finish was obtained as low as 19.7 nm from the initial surface
roughness of 142.9 nm. The outcome of newly developed finishing process can be found useful in its applications in aerospace,
automotive, dies and molds manufacturing industries, semiconductor and optics machining etc.
Abstract: The motivation of this work was to find a suitable 3D
scanner for human body parts digitalization in the field of prosthetics
and orthotics. The main project objective is to compare the three
hand-held portable scanners (two optical and one laser) and two
optical tripod scanners. The comparison was made with respect of
scanning detail, simplicity of operation and ability to scan directly on
the human body. Testing was carried out on a plaster cast of the
upper limb and directly on a few volunteers. The objective monitored
parameters were time of digitizing and post-processing of 3D data
and resulting visual data quality. Subjectively, it was considered level
of usage and handling of the scanner. The new tripod was developed
to improve the face scanning conditions. The results provide an
overview of the suitability of different types of scanners.
Abstract: Solid dispersions (SD) of curcuminpolyvinylpyrrolidone
in the ratio of 1:2, 1:4, 1:5, 1:6, and 1:8 were
prepared in an attempt to increase the solubility and dissolution.
Solubility, dissolution, powder X-ray diffraction (XRD), differential
scanning calorimetry (DSC) and Fourier transform infrared
spectroscopy (FTIR) of solid dispersions, physical mixtures (PM)
and curcumin were evaluated. Both solubility and dissolution of
curcumin solid dispersions were significantly greater than those
observed for physical mixtures and intact curcumin. The powder
X-ray diffractograms indicated that the amorphous curcumin was
obtained from all solid dispersions. It was found that the optimum
weight ratio for curcumin:PVP K-30 is 1:6. The 1:6 solid dispersion
still in the amorphous from after storage at ambient temperature for 2
years and the dissolution profile did not significantly different from
freshly prepared.
Abstract: In this paper we investigate how wide-ranging
organizational support and the more specific form of support,
namely management support, may influence on tourism workers
satisfaction with a cash transaction system. The IS continuance
theory, proposed by Bhattacherjee in 2001, is utilized as a
theoretical framework. This implies that both perceived usefulness
and ease of use is included in the research model, in addition to
organizational and management support. The sample consists of
500 workers from 10 cruise and tourist ferries in Scandinavia that
use a cash transaction system to perform their work tasks. Using
structural equation modelling, results indicate that organizational
support and ease of use perceptions is critical for the users- level of
satisfaction with the cash transaction system.The findings have
implications for business managers and IS practitioners that want
to increase the quality of IT-based business processes within the
tourism industry.
Abstract: The crystallization kinetics and phase transformation
of SiO2.Al2O3.0,56P2O5.1,8CaO.0,56CaF2 glass have been
investigated using differential thermal analysis (DTA), x-ray
diffraction (XRD), and scanning electron microscopy (SEM). Glass
samples were obtained by melting the glass mixture at 14500С/120
min. in platinum crucibles. The mixture were prepared from
chemically pure reagents: SiO2, Al(OH)3, H3PO4, CaCO3 and CaF2.
The non-isothermal kinetics of crystallization was studied by
applying the DTA measurements carried out at various heating rates.
The activation energies of crystallization and viscous flow were
measured as 348,4 kJ.mol–1 and 479,7 kJ.mol–1 respectively. Value of
Avrami parameter n ≈ 3 correspond to a three dimensional of crystal
growth mechanism. The major crystalline phase determined by XRD
analysis was fluorapatite (Ca(PO4)3F) and as the minor phases –
fluormargarite (CaAl2(Al2SiO2)10F2) and vitlokite (Ca9P6O24). The
resulting glass-ceramic has a homogeneous microstructure, composed
of prismatic crystals, evenly distributed in glass phase.
Abstract: Using steelmaking slag as a raw material, aragonite superstructure product had been synthesized via an indirect CO2 mineral sequestration rout. It mainly involved two separate steps, in which the element of calcium is first selectively leached from steelmaking slag by a novel leaching media consisting of organic solvent Tributyl phosphate (TBP), acetic acid, and ultra-purity water, followed by enhanced carbonation in a separate step for aragonite superstructure production as well as efficiency recovery of leaching media. Based on the different leaching medium employed in the steelmaking slag leaching process, two typical products were collected from the enhanced carbonation step. The products were characterized by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM), respectively. It reveals that the needle-like aragonite crystals self-organized into aragonite superstructure particles including aragonite microspheres as well as dumbbell-like spherical particles, can be obtained from the steelmaking slag with the purity over 99%.
Abstract: This report shows the performance of composite
biodegradable film from chitosan, starch and sawdust fiber. The main
objectives of this research are to fabricate and characterize composite
biodegradable film in terms of morphology and physical properties.
The film was prepared by casting method. Sawdust fiber was used as
reinforcing agent and starch as polymer matrix in the casting
solution. The morphology of the film was characterized using atomic
force microscope (AFM). The result showed that the film has
smooth structure. Chemical composition of the film was investigated
using Fourier transform infrared (FTIR) where the result revealed
present of starch in the film. The thermal properties were
characterized using thermal gravimetric analyzer (TGA) and
differential scanning calorimetric (DSC) where the results showed
that the film has small difference in melting and degradation
temperature.
Abstract: In the present study, changes of morphology and
mechanical characteristics in the lumbar vertebrae of the
ovariectomised (OVX) rat were investigated. In previous researches,
there were many studies about morphology like volume fraction and
trabecular thickness based on Micro - Computed Tomography (Micro
- CT). However, detecting and tracking long-term changes in the
trabecular bone of the lumbar vertebrae for the OVX rat were few. For
this study, one female Sprague-Dawley rat was used: an OVX rat. The
4th Lumbar of the OVX rat was subjected to in-vivo micro-CT.
Detecting and tracking long-term changes could be investigated in the
trabecular bone of the lumbar vertebrae for an OVX rat using in-vivo
micro-CT. An OVX rat was scanned at week 0 (just before surgery), at
week 4, at week 8, week 16, week 22 and week 56 after surgery. Finite
element (FE) analysis was used to investigate mechanical
characteristics of the lumbar vertebrae for an OVX rat. When the OVX
rat (at week 56) was compared with the OVX rat (at week 0), volume
fraction was decreased by 80% and effective modulus was decreased
by 75%.
Abstract: Manufacturing processes demand tight dimensional
tolerances. The paper concerns a transducer for precise measurement
of displacement, based on a camera containing a linescan chip.
When tests were conducted using a track of black and white stripes
with a 2mm pitch, errors in measuring on individual cycle amounted
to 1.75%, suggesting that a precision of 35 microns is achievable.
Abstract: The purpose of this study is to present a non invasive
method for the marginal adaptation evaluation in class V composite
restorations. Standardized class V cavities, prepared in human
extracted teeth, were filled with Premise (Kerr) composite. The
specimens were thermo cycled. The interfaces were examined by
Optical Coherence Tomography method (OCT) combined with the
confocal microscopy and fluorescence. The optical configuration
uses two single mode directional couplers with a superluminiscent
diode as the source at 1300 nm. The scanning procedure is similar to
that used in any confocal microscope, where the fast scanning is enface
(line rate) and the depth scanning is much slower (at the frame
rate). Gaps at the interfaces as well as inside the composite resin
materials were identified. OCT has numerous advantages which
justify its use in vivo as well as in vitro in comparison with
conventional techniques.
Abstract: Endemic Artemia franciscana populations can be found throughout the American continent and also as an introduced specie in several country all over the world, such as in the Mediterranean region where Artemia franciscana was identified as an invasive specie replacing native Artemia parthenogenetica and Artemia salina. In the present study, the characterization of the new invasive Artemia franciscana reported from Sabkhet Halk El-Menzel (Tunisia) was done based on the cysts biometry, nauplii instar-I length, Adult sexual dimorphism and fatty acid profile. The mean value of the diameter of non-decapsulated and decapsulated cysts, chorion thickness and naupliar length is 235.8, 226.3, 4.75 and 426.8 μm, respectively. Sexual dimorphism for adults specimen showed that maximal distance between compound eyes, diameter for compound eyes, length of first antenna and the abdomen length compared to the total body length ratio, are the most important variables for males and females discrimination with a total contribution of 62.39 %. The analysis of fatty acid methyl esters profile of decapsulated cysts resulted in low levels of linolenic acid (LLA, C18:3n-3) and high levels of eicosapentaenoic acid (EPA, C20:5n-3) with 3.11 and 11.10 %, respectively. Low quantity of docosahexaenoic acid (DHA, 22:6n-3) was also observed with 0.17 mg.g-1 dry weight.
Abstract: Medical imaging uses the advantage of digital
technology in imaging and teleradiology. In teleradiology systems
large amount of data is acquired, stored and transmitted. A major
technology that may help to solve the problems associated with the
massive data storage and data transfer capacity is data compression
and decompression. There are many methods of image compression
available. They are classified as lossless and lossy compression
methods. In lossy compression method the decompressed image
contains some distortion. Fractal image compression (FIC) is a lossy
compression method. In fractal image compression an image is
coded as a set of contractive transformations in a complete metric
space. The set of contractive transformations is guaranteed to
produce an approximation to the original image. In this paper FIC is
achieved by PIFS using quadtree partitioning. PIFS is applied on
different images like , Ultrasound, CT Scan, Angiogram, X-ray,
Mammograms. In each modality approximately twenty images are
considered and the average values of compression ratio and PSNR
values are arrived. In this method of fractal encoding, the
parameter, tolerance factor Tmax, is varied from 1 to 10, keeping the
other standard parameters constant. For all modalities of images the
compression ratio and Peak Signal to Noise Ratio (PSNR) are
computed and studied. The quality of the decompressed image is
arrived by PSNR values. From the results it is observed that the
compression ratio increases with the tolerance factor and
mammogram has the highest compression ratio. The quality of the
image is not degraded upto an optimum value of tolerance factor,
Tmax, equal to 8, because of the properties of fractal compression.
Abstract: The systematic manipulations of shapes and sizes of
inorganic compounds greatly benefit the various application fields
including optics, magnetic, electronics, catalysis and medicine.
However shape control has been much more difficult to achieve.
Hence exploration of novel method for the preparation of differently
shaped nanoparticles is challenging research area. II-VI group of
semiconductor cadmium sulphide (CdS) nanostructure with different
morphologies (such as, acicular like, mesoporous, spherical shapes)
and of crystallite sizes vary from 11 to 16 nm were successfully
synthesized by chemical aqueous precipitation of Cd2+ ions with
homogeneously released S2- ions from decomposition of cadmium
sulphate (CdSO4) and thioacetamide (CH3CSNH2) by annealing at
different radiations (microwave, ultrasonic and sunlight) with matter
and systematic research has been done for various factors affecting
the controlled growth rate of CdS nanoparticles. The obtained
nanomaterials have been characterized by X-ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FTIR),
Thermogravometric (DSC-TGA) analysis and Scanning Electron
Microscopy (SEM). The result indicates that on increasing the
reaction time particle size increases but on increasing the molar ratios
grain size decreases.