Abstract: The aim of the present study is to analyze the generation of osteoporotic vertebral bone induced by lack of calcium during growth period and analyze its effects for disc degeneration, based on biomechanical and histomorphometrical study. Mechanical and histomorphological characteristics of lumbar vertebral bones and discs of rats with calcium free diet (CFD) were detected and tracked by using high resolution in-vivo micro-computed tomography (in-vivo micro-CT), finite element (FE) and histological analysis. Twenty female Sprague-Dawley rats (6 weeks old, approximate weight 170g) were randomly divided into two groups (CFD group: 10, NOR group: 10). The CFD group was maintained on a refmed calcium-controlled semisynthetic diet without added calcium, to induce osteoporosis. All lumbar (L 1-L6) were scanned by using in vivo micro-CT with 35i.un resolution at 0, 4, 8 weeks to track the effects of CFD on the generation of osteoporosis. The fmdings of the present study indicated that calcium insufficiency was the main factor in the generation of osteoporosis and it induced lumbar vertebral disc degeneration. This study is a valuable experiment to firstly evaluate osteoporotic vertebral bone and disc degeneration induced by lack of calcium during growth period from a biomechanical and histomorphometrical point of view.
Abstract: Nanocrystals (NC) alloyed composite CdSxSe1-x(x=0
to 1) have been prepared using the chemical solution deposition
technique. The energy band gap of these alloyed nanocrystals of
approximately the same size, have been determined by scanning
tunneling spectroscopy (STS) technique at room temperature. The
values of the energy band gap obtained directly using STS are
compared to those measured by optical spectroscopy. Increasing the
molar fraction ratio x from 0 to 1 causes clearly observed increase in
the band gap of the alloyed composite nanocrystal. Vegard-s law was
applied to calculate the parameters of the effective mass
approximation (EMA) model and the dimension obtained were
compared to the values measured by STM. The good agreement of
the calculated and measured values is a direct result of applying
Vegard's law in the nanocomposites.
Abstract: The study of effect of laser scanning speed on
material efficiency in Ti6Al4V application is very important because unspent powder is not reusable because of high temperature oxygen
pick-up and contamination. This study carried out an extensive study
on the effect of scanning speed on material efficiency by varying the
speed between 0.01 to 0.1m/sec. The samples are wire brushed and
cleaned with acetone after each deposition to remove un-melted
particles from the surface of the deposit. The substrate is weighed before and after deposition. A formula was developed to calculate the
material efficiency and the scanning speed was compared with the
powder efficiency obtained. The results are presented and discussed.
The study revealed that the optimum scanning speed exists for this study at 0.01m/sec, above and below which the powder efficiency
will drop
Abstract: Vertical ZnO nanowire array films were synthesized
based on aqueous method for sensing applications. ZnO nanowires
were investigated structurally using X-ray diffraction (XRD) and
scanning electron microscopy (SEM). The gas-sensing properties of
ZnO nanowires array films are studied. It is found that the ZnO
nanowires array film sensor exhibits excellent sensing properties
towards O2 and CO2 at 100 °C with the response time shorter than 5
s. High surface area / volume ratio of vertical ZnO nanowire and high
mobility accounts for the fast response and recovery. The sensor
response was measured in the range from 100 to 500 ppm O2 and CO2
in this study.
Abstract: The characterisation of agro-wastes fibres for composite applications from Nigeria using X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM) has been done. Fibres extracted from groundnut shell, coconut husk, rice husk, palm fruit bunch and palm fruit stalk are processed using two novel cellulose fibre production methods developed by the authors. Cellulose apparent crystallinity calculated using the deconvolution of the diffractometer trace shows that the amorphous portion of cellulose was permeable to hydrolysis yielding high crystallinity after treatment. All diffratograms show typical cellulose structure with well-defined 110, 200 and 040 peaks. Palm fruit fibres had the highest 200 crystalline cellulose peaks compared to others and it is an indication of rich cellulose content. Surface examination of the resulting fibres using SEM indicates the presence of regular cellulose network structure with some agglomerated laminated layer of thin leaves of cellulose microfibrils. The surfaces were relatively smooth indicating the removal of hemicellulose, lignin and pectin.
Abstract: When it comes to last, it is regarded as the critical
foundation of shoe design and development. A computer aided
methodology for various last form designs is proposed in this study.
The reverse engineering is mainly applied to the process of scanning
for the last form. Then with the minimum energy for revision of
surface continuity, the surface reconstruction of last is rebuilt by the
feature curves of the scanned last. When the surface reconstruction of
last is completed, the weighted arithmetic mean method is applied to
the computation on the shape morphing for the control mesh of last,
thus 3D last form of different sizes is generated from its original form
feature with functions remained. In the end, the result of this study is
applied to an application for 3D last reconstruction system. The
practicability of the proposed methodology is verified through later
case studies.
Abstract: Renewable and non-renewable resource constraints have been vast studied in theoretical fields of project scheduling problems. However, although cumulative resources are widespread in practical cases, the literature on project scheduling problems subject to these resources is scant. So in order to study this type of resources more, in this paper we use the framework of a resource constrained project scheduling problem (RCPSP) with finish-start precedence relations between activities and subject to the cumulative resources in addition to the renewable resources. We develop a branch and bound algorithm for this problem customizing precedence tree algorithm of RCPSP. We perform extensive experimental analysis on the algorithm to check its effectiveness and performance for solving different instances of the problem in question.
Abstract: Controlled modification of appropriate sharpness for
nanotips is of paramount importance to develop novel materials and
functional devices at a nanometer resolution. Herein, we present a
reliable and unique strategy of laser irradiation enhanced
physicochemical etching to manufacture super sharp tungsten tips
with reproducible shape and dimension as well as high yields
(~80%). The corresponding morphology structure evolution of
tungsten tips and laser-tip interaction mechanisms were
systematically investigated and discussed using field emission
scanning electron microscope (SEM) and physical optics statistics
method with different fluences under 532 nm laser irradiation. This
work paves the way for exploring more accessible metallic tips
applications with tunable apex diameter and aspect ratio, and,
furthermore, facilitates the potential sharpening enhancement
technique for other materials used in a variety of nanoscale devices.
Abstract: In this study, we report the synthesis and
characterization of nanohydroxyapatite (nHAp) in gelatin-starch
matrix via biomimetic method. Characterization of the samples was
performed using X-ray diffraction (XRD) and Fourier Transform
infrared spectroscopy (FT-IR). The Size and morphology of the
nHAp samples were determined using scanning and transmission
electron microscopy (SEM and TEM). The results reveal that the
shape and morphology of nHAp is influenced by presence of
biopolymers as template. Carbonyl and amino groups from gelatin
and hydroxyl from starch play crucial roles in HAp formation on the
surface of gelatin-starch.
Abstract: There are few studies on eggshell of leatherback turtle
which is endangered species in Thailand. This study was focusing on
the ultrastructure and elemental composition of leatherback turtle
eggshells collected from Andaman Sea Shore, Thailand during the
nesting season using scanning electron microscope (SEM). Three
eggshell layers of leatherback turtle; the outer cuticle layer or
calcareous layer, the middle layer or middle multistrata layer and the
inner fibrous layer were recognized. The outer calcareous layer was
thick and porosity which consisted of loose nodular units of various
crystal shapes and sizes. The loose attachment between these units
resulted in numerous spaces and openings. The middle layer was
compact thick with several multistrata and contained numerous
openings connecting to both outer cuticle layer and inner fibrous
layer. The inner fibrous layer was compact and thin, and composed of
numerous reticular fibers. Energy dispersive X-ray microanalysis
detector revealed energy spectrum of X-rays character emitted from
all elements on each layer. The percentages of all elements were
found in the following order: carbon (C) > oxygen (O) > calcium
(Ca) > sulfur (S) > potassium (K) > aluminum (Al) > iodine (I) >
silicon (Si) > chlorine (Cl) > sodium (Na) > fluorine (F) >
phosphorus (P) > magnesium (Mg). Each layer consisted of high
percentage of CaCO3 (approximately 98%) implying that it was
essential for turtle embryonic development. A significant difference
was found in the percentages of Ca and Mo in the 3layers. Moreover,
transition metal, metal and toxic non-metal contaminations were
found in leatherback turtle eggshell samples. These were palladium
(Pd), molybdenum (Mo), copper (Cu), aluminum (Al), lead (Pb), and
bromine (Br). The contamination elements were seen in the outer
layers except for Mo. All elements were readily observed and
mapped using Smiling program. X-ray images which mapped the
location of all elements were showed. Calcium containing in the
eggshell appeared in high contents and was widely distributing in
clusters of the outer cuticle layer to form CaCO3 structure. Moreover,
the accumulation of Na and Cl was observed to form NaCl which was
widely distributing in 3 eggshell layers. The results from this study
would be valuable on assessing the emergent success in this
endangered species.
Abstract: Void formation in underfill is considered as failure
in flip chip manufacturing process. Void formation possibly caused
by several factors such as poor soldering and flux residue during
die attach process, void entrapment due moisture contamination,
dispense pattern process and setting up the curing process. This
paper presents the comparison of single step and two steps curing
profile towards the void and black dots formation in underfill for
Hi-CTE Flip Chip Ceramic Ball Grid Array Package (FC-CBGA).
Statistic analysis was conducted to analyze how different factors
such as wafer lot, sawing technique, underfill fillet height and
curing profile recipe were affected the formation of voids and
black dots. A C-Mode Scanning Aqoustic Microscopy (C-SAM)
was used to scan the total count of voids and black dots. It was
shown that the 2 steps curing profile provided solution for void
elimination and black dots in underfill after curing process.
Abstract: The mechanical properties including flexural and
tensile of neat vinyl ester and polymer based on layered silicate
nanocomposite materials are discussed. The addition of layered
silicate into the polymer matrix increased the tensile and flexural
modulus up to 1 wt.% clay loading. The incorporation of more clay
resulted in decreasing the mechanical properties which was traced to
the existence of aggregation layers. Likewise, up to 1 wt.% clay
loading, the thermal behaviour showed significant improvements and
at higher clay loading the thermal pattern was reduced. The
aggregation layers imparted a negative impact on the overall
mechanical and thermal properties. Wide Angle X-ray Diffraction,
Scanning Electron Microscopy and Transmission Electron
Microscopy were utilised in order to characterise the interlamellar
structure of nanocomposites.
Abstract: Coated tool inserts can be considered as the backbone
of machining processes due to their wear and heat resistance.
However, defects of coating can degrade the integrity of these inserts
and the number of these defects should be minimized or eliminated if
possible. Recently, the advancement of coating processes and
analytical tools open a new era for optimizing the coating tools.
First, an overview is given regarding coating technology for cutting
tool inserts. Testing techniques for coating layers properties, as well
as the various coating defects and their assessment are also surveyed.
Second, it is introduced an experimental approach to examine the
possible coating defects and flaws of worn multicoated carbide
inserts using two important techniques namely scanning electron
microscopy and atomic force microscopy. Finally, it is
recommended a simple procedure for investigating manufacturing
defects and flaws of worn inserts.
Abstract: Radio-frequency identification has entered as a beneficial means with conforming GS1 standards to provide the best solutions in the manufacturing area. It competes with other automated identification technologies e.g. barcodes and smart cards with regard to high speed scanning, reliability and accuracy as well. The purpose of this study is to improve production line-s performance by implementing RFID system in the manufacturing area on the basis of radio-frequency identification (RFID) system by 3D modeling in the program Cinema 4D R13 which provides obvious graphical scenes for users to portray their applications. Finally, with regard to improving system performance, it shows how RFID appears as a well-suited technology in a comparison of the barcode scanner to handle different kinds of raw materials in the production line base on logical process.
Abstract: Information is increasing in volumes; companies are overloaded with information that they may lose track in getting the intended information. It is a time consuming task to scan through each of the lengthy document. A shorter version of the document which contains only the gist information is more favourable for most information seekers. Therefore, in this paper, we implement a text summarization system to produce a summary that contains gist information of oil and gas news articles. The summarization is intended to provide important information for oil and gas companies to monitor their competitor-s behaviour in enhancing them in formulating business strategies. The system integrated statistical approach with three underlying concepts: keyword occurrences, title of the news article and location of the sentence. The generated summaries were compared with human generated summaries from an oil and gas company. Precision and recall ratio are used to evaluate the accuracy of the generated summary. Based on the experimental results, the system is able to produce an effective summary with the average recall value of 83% at the compression rate of 25%.
Abstract: Most CT reconstruction system x-ray computed
tomography (CT) is a well established visualization technique in
medicine and nondestructive testing. However, since CT scanning
requires sampling of radiographic projections from different viewing
angles, common CT systems with mechanically moving parts are too
slow for dynamic imaging, for instance of multiphase flows or live
animals. A large number of X-ray projections are needed to
reconstruct CT images, so the collection and calculation of the
projection data consume too much time and harmful for patient. For
the purpose of solving the problem, in this study, we proposed a
method for tomographic reconstruction of a sample from a limited
number of x-ray projections by using linear interpolation method. In
simulation, we presented reconstruction from an experimental x-ray
CT scan of a Aluminum phantom that follows to two steps: X-ray
projections will be interpolated using linear interpolation method and
using it for CT reconstruction based upon Ordered Subsets
Expectation Maximization (OSEM) method.
Abstract: This paper presents the results of a comprehensive
investigation of five blackouts that occurred on 28 August to 8
September 2011 due to bushing failures of the 132/33 kV, 125 MVA
transformers at JBB Ali Grid station. The investigation aims to
explore the root causes of the bushing failures and come up with
recommendations that help in rectifying the problem and avoiding the
reoccurrence of similar type of incidents. The incident reports about
the failed bushings and the SCADA reports at this grid station were
examined and analyzed. Moreover, comprehensive power quality
field measurements at ten 33/11 kV substations (S/Ss) in JBB Ali
area were conducted, and frequency scans were performed to verify
any harmonic resonance frequencies due to power factor correction
capacitors. Furthermore, the daily operations of the on-load tap
changers (OLTCs) of both the 125 MVA and 20 MVA transformers
at JBB Ali Grid station have been analyzed. The investigation
showed that the five bushing failures were due to a local problem, i.e.
internal degradation of the bushing insulation. This has been
confirmed by analyzing the time interval between successive OLTC
operations of the faulty grid transformers. It was also found that
monitoring the number of OLTC operations can help in predicting
bushing failure.
Abstract: This paper presents an optimization technique to economic load dispatch (ELD) problems with considering the daily load patterns and generator constraints using a particle swarm optimization (PSO). The objective is to minimize the fuel cost. The optimization problem is subject to system constraints consisting of power balance and generation output of each units. The application of a constriction factor into PSO is a useful strategy to ensure convergence of the particle swarm algorithm. The proposed method is able to determine, the output power generation for all of the power generation units, so that the total constraint cost function is minimized. The performance of the developed methodology is demonstrated by case studies in test system of fifteen-generation units. The results show that the proposed algorithm scan give the minimum total cost of generation while satisfying all the constraints and benefiting greatly from saving in power loss reduction
Abstract: In this paper, we introduce a new method for elliptical
object identification. The proposed method adopts a hybrid scheme
which consists of Eigen values of covariance matrices, Circular
Hough transform and Bresenham-s raster scan algorithms. In this
approach we use the fact that the large Eigen values and small Eigen
values of covariance matrices are associated with the major and minor
axial lengths of the ellipse. The centre location of the ellipse can be
identified using circular Hough transform (CHT). Sparse matrix
technique is used to perform CHT. Since sparse matrices squeeze zero
elements and contain a small number of nonzero elements they
provide an advantage of matrix storage space and computational time.
Neighborhood suppression scheme is used to find the valid Hough
peaks. The accurate position of circumference pixels is identified
using raster scan algorithm which uses the geometrical symmetry
property. This method does not require the evaluation of tangents or
curvature of edge contours, which are generally very sensitive to
noise working conditions. The proposed method has the advantages of
small storage, high speed and accuracy in identifying the feature. The
new method has been tested on both synthetic and real images.
Several experiments have been conducted on various images with
considerable background noise to reveal the efficacy and robustness.
Experimental results about the accuracy of the proposed method,
comparisons with Hough transform and its variants and other
tangential based methods are reported.
Abstract: In this paper we present a new method for coin
identification. The proposed method adopts a hybrid scheme using
Eigenvalues of covariance matrix, Circular Hough Transform (CHT)
and Bresenham-s circle algorithm. The statistical and geometrical
properties of the small and large Eigenvalues of the covariance
matrix of a set of edge pixels over a connected region of support are
explored for the purpose of circular object detection. Sparse matrix
technique is used to perform CHT. Since sparse matrices squeeze
zero elements and contain only a small number of non-zero elements,
they provide an advantage of matrix storage space and computational
time. Neighborhood suppression scheme is used to find the valid
Hough peaks. The accurate position of the circumference pixels is
identified using Raster scan algorithm which uses geometrical
symmetry property. After finding circular objects, the proposed
method uses the texture on the surface of the coins called texton,
which are unique properties of coins, refers to the fundamental micro
structure in generic natural images. This method has been tested on
several real world images including coin and non-coin images. The
performance is also evaluated based on the noise withstanding
capability.