Abstract: The paper presents a novel screening method to
indicate congenital heart diseases (CHD), which otherwise could
remain undetected because of their low level. Therefore, not
belonging to the high-risk population, the pregnancies are not subject
to the regular fetal monitoring with ultrasound echocardiography.
Based on the fact that CHD is a morphological defect of the heart
causing turbulent blood flow, the turbulence appears as a murmur,
which can be detected by fetal phonocardiography (fPCG). The
proposed method applies measurements on the maternal abdomen
and from the recorded sound signal a sophisticated processing
determines the fetal heart murmur. The paper describes the problems
and the additional advantages of the fPCG method including the
possibility of measurements at home and its combination with the
prescribed regular cardiotocographic (CTG) monitoring. The
proposed screening process implemented on a telemedicine system
provides an enhanced safety against hidden cardiac diseases.
Abstract: The substantial development of the construction
industry has forced the cement industry, its major support, to focus
on achieving maximum productivity to meet the growing demand for
this material. This means that the reliability of a cement production
system needs to be at the highest level that can be achieved by good
maintenance. This paper studies the extent to which the
implementation of RCM is needed as a strategy for increasing the
reliability of the production systems component can be increased,
thus ensuring continuous productivity. In a case study of four Libyan
cement factories, 80 employees were surveyed and 12 top and middle
managers interviewed. It is evident that these factories usually
breakdown more often than once per month which has led to a
decline in productivity. In many times they cannot achieve the
minimum level of production amount. This has resulted from the
poor reliability of their production systems as a result of poor or
insufficient maintenance. It has been found that most of the factories’
employees misunderstand maintenance and its importance. The main
cause of this problem is the lack of qualified and trained staff, but in
addition it has been found that most employees are not found to be
motivated as a result of a lack of management support and interest. In
response to these findings, it has been suggested that the RCM
strategy should be implemented in the four factories. The results
show the importance of the development of maintenance strategies
through the implementation of RCM in these factories. The purpose
of it would be to overcome the problems that could secure the
reliability of the production systems. This study could be a useful
source of information for academic researchers and the industrial
organizations which are still experiencing problems in maintenance
practices.
Abstract: Masonry infill walls are inevitable in the selfsupporting
structures, but their contribution in the resistance to
earthquake loads is generally neglected in the structural analyses. The
principal aim of this work through a numerical study of masonry
infill walls behavior in structures subjected to horizontal load is to
propose by finite elements numerical modeling, a more reliable
approach, faster and close to reality. In this study, 3D Finite Element
Analysis was developed to study the behavior of masonry infill walls
in structures subjected to horizontal load; the finite element software
being used was ABAQUS, it is observed that more rigidity of the
masonry filling is significant, more the structure is rigid, we can so
conclude that the filling brings an additional rigidity to the structure
not to be neglected; it is also observed that when the framework is
subjected to horizontal loads, the framework separates from the
filling on the level of the tended diagonal.
Abstract: Computational fluid dynamics analysis of the burning
of syngas fuels derived from biomass and plastic solid waste mixture
through gasification process is presented in this paper. The syngas
fuel is burned in gas turbine can combustor. Gas turbine can
combustor with swirl is designed to burn the fuel efficiently and
reduce the emissions. The main objective is to test the impact of the
alternative syngas fuel compositions and lower heating value on the
combustion performance and emissions. The syngas fuel is produced
by blending palm kernel shell (PKS) with polyethylene (PE) waste
via catalytic steam gasification (fluidized bed reactor). High
hydrogen content syngas fuel was obtained by mixing 30% PE waste
with PKS. The syngas composition obtained through the gasification
process is 76.2% H2, 8.53% CO, 4.39% CO2 and 10.90% CH4. The
lower heating value of the syngas fuel is LHV = 15.98 MJ/m3. Three
fuels were tested in this study natural gas (100%CH4), syngas fuel
and pure hydrogen (100% H2). The power from the combustor was
kept constant for all the fuels tested in this study. The effect of syngas
fuel composition and lower heating value on the flame shape, gas
temperature, mass of carbon dioxide (CO2) and nitrogen oxides
(NOX) per unit of energy generation is presented in this paper. The
results show an increase of the peak flame temperature and NO mass
fractions for the syngas and hydrogen fuels compared to natural gas
fuel combustion. Lower average CO2 emissions at the exit of the
combustor are obtained for the syngas compared to the natural gas
fuel.
Abstract: This study focuses on a novel method for dispersion
and distribution of reinforcement under high intensive shear stress to
produce metal composites. The polyacrylonitrile (PAN)-based short
carbon fiber (Csf) and Nextel 610 alumina fiber were dispersed under
high intensive shearing at mushy zone in semi-solid of A356 by a
novel method. The bundles and clusters were embedded by
infiltration of slurry into the clusters, thus leading to a uniform
microstructure. The fibers were embedded homogenously into the
aluminum around 576-580°C with around 46% of solid fraction.
Other experiments at 615°C and 568°C which are contained 0% and
90% solid respectively were not successful for dispersion and
infiltration of aluminum into bundles of Csf. The alumina fiber has
been cracked by high shearing load. The morphologies and
crystalline phase were evaluated by SEM and XRD. The adopted
thixo-process effectively improved the adherence and distribution of
Csf into Al that can be developed to produce various composites by
thixomixing.
Abstract: Microbes have been used to solve environmental
problems for many years. The role of microorganism to sequester,
precipitate or alter the oxidation state of various heavy metals has
been extensively studied. Treatment using microorganism interacts
with toxic metal are very diverse. The purpose of this research is to
remove the mercury using Pseudomonas putida (P. putida), pure
culture ATTC 49128 at optimum growth parameters such as
techniques of culture, acclimatization time and speed of incubator
shaker. Thus, in this study, the optimum growth parameters of P.
putida were obtained to achieve the maximum of mercury removal.
Based on the optimum parameters of P. putida for specific growth
rate, the removal of two different mercury concentration, 1 ppm and
4 ppm were studied. From mercury nitrate solution, a mercuryresistant
bacterial strain which is able to reduce from ionic mercury
to metallic mercury was used to reduce ionic mercury. The overall
levels of mercury removal in this study were between 80% and 89%.
The information obtained in this study is of fundamental for
understanding of the survival of P. putida ATTC 49128 in mercury
solution. Thus, microbial mercury removal is a potential
bioremediation for wastewater especially in petrochemical industries
in Malaysia.
Abstract: In contrast with literal meaning of nano, researchers
have been achieved mega adventures in this area and every day more
nanomaterials are being introduced to the market. After long time
application of fossil-based plastics, nowadays accumulation of their
waste seems to be a big problem to the environment. On the other
hand, mankind has more attention to safety and living environment.
Replacing common plastic packaging materials with degradable ones
that degrade faster and convert to non-dangerous components like
water and carbon dioxide have more attractions; these new materials
are based on renewable and inexpensive sources of starch and
cellulose. However, the functional properties of them do not suitable
for packaging. At this point, nanotechnology has an important role.
Utilizing of nanomaterials in polymer structure will improve
mechanical and physical properties of them; nanocrystalline cellulose
(NCC) has this ability. This work has employed a chemical method to
produce NCC and starch bio nanocomposite containing NCC. X-Ray
Diffraction technique has characterized the obtained materials.
Results showed that applied method is a suitable one as well as
applicable one to NCC production.
Abstract: Mammography is widely used technique for breast cancer
screening. There are various other techniques for breast cancer screening
but mammography is the most reliable and effective technique. The
images obtained through mammography are of low contrast which
causes problem for the radiologists to interpret. Hence, a high quality
image is mandatory for the processing of the image for extracting any
kind of information from it. Many contrast enhancement algorithms have
been developed over the years. In the present work, an efficient
morphology based technique is proposed for contrast enhancement of
masses in mammographic images. The proposed method is based on
Multiscale Morphology and it takes into consideration the scale of the
structuring element. The proposed method is compared with other stateof-
the-art techniques. The experimental results show that the proposed
method is better both qualitatively and quantitatively than the other
standard contrast enhancement techniques.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: Driver fatigue is an important factor in the increasing
number of road accidents. Dynamic template matching method was
proposed to address the problem of real-time driver fatigue detection
system based on eye-tracking. An effective vision based approach
was used to analyze the driver’s eye state to detect fatigue. The driver
fatigue system consists of Face detection, Eye detection, Eye
tracking, and Fatigue detection. Initially frames are captured from a
color video in a car dashboard and transformed from RGB into YCbCr
color space to detect the driver’s face. Canny edge operator was used
to estimating the eye region and the locations of eyes are extracted.
The extracted eyes were considered as a template matching for eye
tracking. Edge Map Overlapping (EMO) and Edge Pixel Count
(EPC) matching function were used for eye tracking which is used to
improve the matching accuracy. The pixel of eyeball was tracked
from the eye regions which are used to determine the fatigue state of
the driver.
Abstract: Pneumatic reactors have been widely employed in various sectors of the chemical industry, especially where are required high heat and mass transfer rates. This study aimed to obtain correlations that allow the prediction of gas hold-up (Ԑ) and volumetric oxygen transfer coefficient (kLa), and compare these values, for three models of pneumatic reactors on two scales utilizing Newtonian fluids. Values of kLa were obtained using the dynamic pressure-step method, while e was used for a new proposed measure. Comparing the three models of reactors studied, it was observed that the mass transfer was superior to draft-tube airlift, reaching e of 0.173 and kLa of 0.00904s-1. All correlations showed good fit to the experimental data (R2≥94%), and comparisons with correlations from the literature demonstrate the need for further similar studies due to shortage of data available, mainly for airlift reactors and high viscosity fluids.
Abstract: This paper presents the results of an experimental
study undertaken to evaluate the local bond stress-slip response of
short embedment of reinforcing bars in normal concrete (NC) and
high performance fiber reinforced cement composites (HPFRCC)
blocks. Long embedment was investigated as well to gain insights on
the distribution of strain, slip, bar stress and bond stress along the bar
especially in post-yield range. A total of 12 specimens were tested,
by means of pull-out of the reinforcing bars from concrete blocks. It
was found that the enhancement of local bond strength can be
reached up to 50% and ductility of the bond behavior was improved
significantly if HPFRCC is used. Also, under a constant strain at
loaded end, HPFRCC has delayed yielding of bars at other location
from the loaded end. Hence, the reduction of bond stress was slower
for HPFRCC in comparison with NC. Due to the same reason, the
total slips at loaded end for HPFRCC was smaller than NC as
expected. Test results indicated that HPFRCC has better bond slip
behavior which makes it a suitable material to be employed in
anchorage zone such as beam-column joints.
Abstract: In this paper, a new concept of closed-loop design for a
product is presented. The closed-loop design model is developed by
integrating forward design and reverse design. Based on this new
concept, a closed-loop design model for sustainable manufacturing by
integrated evaluation of forward design, reverse design, and green
manufacturing using a fuzzy analytic network process is developed. In
the design stage of a product, with a given product requirement and
objective, there can be different ways to design the detailed
components and specifications. Therefore, there can be different
design cases to achieve the same product requirement and objective.
Subsequently, in the design evaluation stage, it is required to analyze
and evaluate the different design cases. The purpose of this research is
to develop a model for evaluating the design cases by integrated
evaluating the criteria in forward design, reverse design, and green
manufacturing. A fuzzy analytic network process method is presented
for integrated evaluation of the criteria in the three models. The
comparison matrices for evaluating the criteria in the three groups are
established. The total relational values among the three groups
represent the total relational effects. In applications, a super matrix
model is created and the total relational values can be used to evaluate
the design cases for decision-making to select the final design case. An
example product is demonstrated in this presentation. It shows that the
model is useful for integrated evaluation of forward design, reverse
design, and green manufacturing to achieve a closed-loop design for
sustainable manufacturing objective.
Abstract: Some plants of genus Schinus have been used in the
folk medicine as topical antiseptic, digestive, purgative, diuretic,
analgesic or antidepressant, and also for respiratory and urinary
infections. Chemical composition of essential oils of S. molle and S.
terebinthifolius had been evaluated and presented high variability
according with the part of the plant studied and with the geographic
and climatic regions. The pharmacological properties, namely
antimicrobial, anti-tumoural and anti-inflammatory activities are
conditioned by chemical composition of essential oils. Taking into
account the difficulty to infer the pharmacological properties of
Schinus essential oils without hard experimental approach, this work
will focus on the development of a decision support system, in terms
of its knowledge representation and reasoning procedures, under a
formal framework based on Logic Programming, complemented with
an approach to computing centered on Artificial Neural Networks
and the respective Degree-of-Confidence that one has on such an
occurrence.
Abstract: Any variation in environmental characteristics of
geomorphosites would lead to destabilisation of their geotouristic
values all around the planet. The Urmia lake, with an area of
approximately 5,500 km2 and a catchment area of 51,876 km2, and to
which various reasons over time, especially in the last fifty years
have seen a sharp decline and have decreased by about 93 % in two
recent decades. These variations are not only driving significant
changes in the morphology and ecology of the present lake
landscape, but at the same time are shaping newly formed
morphologies, which vanished some valuable geomorphosites or
develop into smaller geomorphosites with significant value from a
scientific and cultural point of view. This paper analyses and
discusses features and evolution in several representative coastal and
island geomorphosites. For this purpose, a total of 23 geomorphosites
were studied in two data series (1963 and 2015) and the respective
data were compared and analysed. The results showed, the total loss
in geomorphosites area in a half century amounted to a loss of more
than 90% of the valuable geomorphosites. Moreover, the comparison
between the mean yearly value of coastal area lost over the entire
period and the yearly average calculated for the shorter period (1998-
2014) clearly indicates a pattern of acceleration. This acceleration in
the rate of reduction in lake area was seen in most of the southern
half of the lake. In the region as well, the general water-level falling
is not only causing the loss of a significant water resource, which is
followed by major impact on regional ecosystems, but is also driving
the most marked recent (last century) changes in the geotouristic
landscapes. In fact, the disappearance of geomorphosites means the
loss of tourism phenomenon. In this context attention must be paid to
the question of conservation. The action needed to safeguard
geomorphosites includes: 1) Preventive action, 2) Corrective action,
and 3) Sharing knowledge.
Abstract: In this study, one of the tools of Islamic financing
known as “Sukuk” a non-interest bearing investment which has
started to be implemented in Turkey and the world as a whole is
discussed. In order to increase the vitality and efficiency of the
economy, by taking lessons from the recent economic crisis new
developments in the banking and investment sector are being
expanded. The purpose of all investors is to obtain more revenue
through the use of capital. The inability of traditional investment
tools to meet the expectations of investors and the interest based
financial system where one investor benefits at the expense of
another there has been the need for a different, reliable and noninterest
bearing financial market that is consistent with the Islamic
rule. As a result an alternative and more reliable interest free
financing tool “Sukuk” rental certificates covering people who are
sensitive to Islamic rules, appeal to all segments, hidden remaining
capital that contributes to the economy, reduce disparities in income
distribution, common risk sharing system of profit and loss sharing
has emerged. Today, for the structural countries by examining the
state of the world market economy the applicability, enactment and
future issues associated with this attractive kind of Islamic finance
namely the “Sukuk” market has been explained.
Abstract: The rationale behind this study is considering
combating and preventing the phenomenon of trafficking in human
beings from a multidisciplinary perspective that involves many layers
of the society.
Trafficking in human beings is an abhorrent phenomenon highly
affecting negatively the victims and their families in both human and
material aspect, sometimes causing irreversible damages. The longer
term effects of this phenomenon, in countries with a weak economic
development and extremely young and dynamic population, such as
Kosovo, without proper measures to prevented and control can cause
tremendous damages in the society. Given the fact that a complete
eradication of this phenomenon is almost impossible, efforts should
be concentrated at least on the prevention and controlling aspects.
Treating trafficking in human beings based on traditional police
tactics, methods and proceedings cannot bring satisfactory results.
There is no doubt that a multi-disciplinary approach is an
irreplaceable requirement, in other words, a combination of authentic
and functional proactive and reactive methods, techniques and tactics.
Obviously, police must exercise its role in preventing and combating
trafficking in human beings, a role sanctioned by the law, however,
police role and contribution cannot by any means considered
complete if all segments of the society are not included in these
efforts. Naturally, civil society should have an important share in
these collaborative and interactive efforts especially in preventive
activities such as: awareness on trafficking risks and damages,
proactive engagement in drafting appropriate legislation and
strategies, law enforcement monitoring and direct or indirect
involvement in protective and supporting activities which benefit the
victims of trafficking etc.
Abstract: This paper addresses the design of hospital Intensive
Care Unit windows for the achievement of visual comfort and energy
savings. The aim was to identify the window size and shading system
configurations that could fulfill daylighting adequacy, avoid glare
and reduce energy consumption. The study focused on addressing the
effect of utilizing different shading systems in association with a
range of Window-to-Wall Ratios (WWR) in different orientations
under the desert clear-sky of Cairo, Egypt.
The results of this study demonstrated that solar penetration is a
critical concern affecting the design of ICU windows in desert
locations, as in Cairo, Egypt. Use of shading systems was found to be
essential in providing acceptable daylight performance and energy
saving. Careful positioning of the ICU window towards a proper
orientation can dramatically improve performance. It was observed
that ICU windows facing the north direction enjoyed the widest range
of successful window configuration possibilities at different WWRs.
ICU windows facing south enjoyed a reasonable number of
configuration options as well. By contrast, the ICU windows facing
the east orientation had a very limited number of options that provide
acceptable performance. These require additional local shading
measures at certain times due to glare incidence. Moreover, use of
horizontal sun breakers and solar screens to protect the ICU windows
proved to be more successful than the other alternatives in a wide
range of Window to Wall Ratios. By contrast, the use of light shelves
and vertical shading devices seemed questionable.
Abstract: Electrodeposition is a simple and economic technique
for precision coating of different shaped substrates with pure metal,
alloy or composite films. Dc electrodeposition was used to produce
Cr, Co-Cr and Co-Cr/TiO2 nano-composite coatings from Cr(III)
based electrolytes onto 316L SS substrates. The effects of TiO2 nanoparticles
concentration on co-deposition of these particles along with
Cr content and microhardness of the coatings were investigated.
Morphology of the Cr, Co-Cr and Co-Cr/TiO2 coatings besides their
tribological behavior were studied. The results showed that increment
of TiO2 nanoparticles concentration from 0 to 30 g L-1 in the bath
increased their co-deposition and Cr content of the coatings from 0 to
3.5 wt.% and from 23.7 to 31.2 wt.%, respectively. Microhardness of
Cr coating was about 920 Hv which was higher than Co-Cr and even
Co-Cr/TiO2 films. Microhardness of Co-Cr and Co-Cr/TiO2 coatings
were improved by increasing their Cr and TiO2 content. All the
coatings had nodular morphology and contained microcracks.
Nodules sizes and the number of microcracks in the alloy and
composite coatings were lower than the Cr film. Wear results
revealed that the Co-Cr/TiO2 coating had the lowest wear loss
between all the samples, while the Cr film had the worst wear
resistance.
Abstract: Authenticity in advertising is the cornerstone of
modern marketing. Despite research advances related to the role of
authenticity in marketing, it remains unclear why customers respond to
authentic brand stories. The results show that different personality
traits will moderate the influence of different authenticity on the levels
of emotion. Whether indexically authentic or iconically authentic
advertisements were shown to extroverts, open people and agreeable
people, they will evoke more positive emotions. When neurotic people
and conscientious people see the iconically authentic advertising
rather than the indexically authentic advertising, they will produce
more negative emotions. In addition, the emotion evoked by
advertising had significant positive impact on brand attitude evoked by
advertising had significant negative impact on brand attitude. These
findings provide some managerial implications and directions for
further research.