Abstract: Sampled-data controller is presented for solid oxide
fuel cell systems which is expressed by a sector bounded nonlinear
model. The proposed control law is obtained by solving a convex
problem satisfying several linear matrix inequalities. Simulation
results are given to show the effectiveness of the proposed design
method.
Abstract: Elastomeric polymer foam has been used widely in
the automotive industry, especially for isolating unwanted vibrations.
Such material is able to absorb unwanted vibration due to its
combination of elastic and viscous properties. However, the ‘creep
effect’, poor stress distribution and susceptibility to high
temperatures are the main disadvantages of such a system.
In this study, improvements in the performance of elastomeric
foam as a vibration isolator were investigated using the concept of
Foam Filled Fluid (FFFluid). In FFFluid devices, the foam takes the
form of capsule shapes, and is mixed with viscous fluid, while the
mixture is contained in a closed vessel. When the FFFluid isolator is
affected by vibrations, energy is absorbed, due to the elastic strain of
the foam. As the foam is compressed, there is also movement of the
fluid, which contributes to further energy absorption as the fluid
shears. Also, and dependent on the design adopted, the packaging
could also attenuate vibration through energy absorption via friction
and/or elastic strain.
The present study focuses on the advantages of the FFFluid
concept over the dry polymeric foam in the role of vibration isolation.
This comparative study between the performance of dry foam and the
FFFluid was made according to experimental procedures. The paper
concludes by evaluating the performance of the FFFluid isolator in
the suspension system of a light vehicle. One outcome of this
research is that the FFFluid may preferable over elastomer isolators
in certain applications, as it enables a reduction in the effects of high
temperatures and of ‘creep effects’, thereby increasing the reliability
and load distribution. The stiffness coefficient of the system has
increased about 60% by using an FFFluid sample. The technology
represented by the FFFluid is therefore considered by this research
suitable for application in the suspension system of a light vehicle.
Abstract: Waste Load Allocation (WLA) strategies usually
intend to find economic policies for water resource management.
Water quality trading (WQT) is an approach that uses discharge
permit market to reduce total environmental protection costs. This
primarily requires assigning discharge limits known as total
maximum daily loads (TMDLs). These are determined by monitoring
organizations with respect to the receiving water quality and
remediation capabilities. The purpose of this study is to compare two
approaches of TMDL assignment for WQT policy in small catchment
area of Haraz River, in north of Iran. At first, TMDLs are assigned
uniformly for the whole point sources to keep the concentrations of
BOD and dissolved oxygen (DO) at the standard level at checkpoint
(terminus point). This was simply simulated and controlled by
Qual2kw software. In the second scenario, TMDLs are assigned
using multi objective particle swarm optimization (MOPSO) method
in which the environmental violation at river basin and total treatment
costs are minimized simultaneously. In both scenarios, the equity
index and the WLA based on trading discharge permits (TDP) are
calculated. The comparative results showed that using economically
optimized TMDLs (2nd scenario) has slightly more cost savings rather
than uniform TMDL approach (1st scenario). The former annually
costs about 1 M$ while the latter is 1.15 M$. WQT can decrease
these annual costs to 0.9 and 1.1 M$, respectively. In other word,
these approaches may save 35 and 45% economically in comparison
with command and control policy. It means that using multi objective
decision support systems (DSS) may find more economical WLA,
however its outcome is not necessarily significant in comparison with
uniform TMDLs. This may be due to the similar impact factors of
dischargers in small catchments. Conversely, using uniform TMDLs
for WQT brings more equity that makes stakeholders not feel that
much envious of difference between TMDL and WQT allocation. In
addition, for this case, determination of TMDLs uniformly would be
much easier for monitoring. Consequently, uniform TMDL for TDP
market is recommended as a sustainable approach. However,
economical TMDLs can be used for larger watersheds.
Abstract: This work consists of a numerical simulation of
convective heat transfer in a vertical plane channel filled with a heat
generating porous medium, in the absence of local thermal
equilibrium. The walls are maintained to a constant temperature and
the inlet velocity is uniform. The dynamic range is described by the
Darcy-Brinkman model and the thermal field by two energy
equations model. A dimensionless formulation is developed for
performing a parametric study based on certain dimensionless groups
such as, the Biot interstitial number, the thermal conductivity ratio
and the volumetric heat generation, q '''. The governing equations are
solved using the finite volume method, gave rise to a multitude of
results concerning in particular the thermal field in the porous
channel and the existence or not of the local thermal equilibrium.
Abstract: This paper aims to study the effect of cold work
condition on the microstructure of Cu-1.5wt%Ti, and Cu-3.5wt%Ti
and hence mechanical properties. The samples under investigation
were machined, and solution heat treated. X-ray diffraction technique
is used to identify the different phases present after cold deformation
by compression and also different heat treatment and also measuring
the relative quantities of phases present. The metallographic
examination is used to study the microstructure of the samples. The
hardness measurements were used to indicate the change in
mechanical properties. The results are compared with the mechanical
properties obtained by previous workers. Experiments on cold
compression followed by aging of Cu-Ti alloys have indicated that
the most efficient hardening of the material results from continuous
precipitation of very fine particles within the matrix. These particles
were reported to be β`-type, Cu4Ti phase. The β`-β transformation
and particles coarsening within the matrix as well as long grain
boundaries were responsible for the overaging of Cu-1.5wt%Ti and
Cu-3.5wt%Ti alloys. It is well known that plate-like particles are β –
type, Cu3Ti phase. Discontinuous precipitation was found to start at
the grain boundaries and expand into grain interior. At the higher
aging temperature, a classic Widmanstätten morphology forms giving
rise to a coarse microstructure comprised of α and the equilibrium
phase β. Those results were confirmed by X-ray analysis, which
found that a few percent of Cu3Ti, β precipitates are formed during
aging at high temperature for long time for both Cu- Ti alloys (i.e.
Cu-1.5wt%Ti and Cu-3.5wt%Ti).
Abstract: Amoxicillin is an antibiotic which is widely used to
treat various infections in both human beings and animals. However,
when amoxicillin is released into the environment, it is a major
problem. Amoxicillin causes bacterial resistance to these drugs and
failure of treatment with antibiotics. Liquid membrane is of great
interest as a promising method for the separation and recovery of the
target ions from aqueous solutions due to the use of carriers for the
transport mechanism, resulting in highly selectivity and rapid
transportation of the desired metal ions. The simultaneous processes
of extraction and stripping in a single unit operation of liquid
membrane system are very interesting. Therefore, it is practical to
apply liquid membrane, particularly the HFSLM for industrial
applications as HFSLM is proved to be a separation process with
lower capital and operating costs, low energy and extractant with
long life time, high selectivity and high fluxes compared with solid
membranes. It is a simple design amenable to scaling up for industrial
applications. The extraction and recovery for (Amoxicillin) through
the hollow fiber supported liquid membrane (HFSLM) using
aliquat336 as a carrier were explored with the experimental data. The
important variables affecting on transport of amoxicillin viz.
extractant concentration and operating time were investigated. The
highest AMOX- extraction percentages of 85.35 and Amoxicillin
stripping of 80.04 were achieved with the best condition at 6 mmol/L
[aliquat336] and operating time 100 min. The extraction reaction
order (n) and the extraction reaction rate constant (kf) were found to
be 1.00 and 0.0344 min-1, respectively.
Abstract: Current systems complexity has reached a degree that
requires addressing conception and design issues while taking into
account environmental, operational, social, legal and financial
aspects. Therefore, one of the main challenges is the way complex
systems are specified and designed. The exponential growing effort,
cost and time investment of complex systems in modeling phase
emphasize the need for a paradigm, a framework and an environment
to handle the system model complexity. For that, it is necessary to
understand the expectations of the human user of the model and his
limits. This paper presents a generic framework for designing
complex systems, highlights the requirements a system model needs
to fulfill to meet human user expectations, and suggests a graphbased
formalism for modeling complex systems. Finally, a set of
transformations are defined to handle the model complexity.
Abstract: Construction projects are information intensive in
nature and involve many activities that are related to each other.
Wireless technologies can be used to improve the accuracy and
timeliness of data collected from construction sites and shares it with
appropriate parties. Nonetheless, the construction industry tends to be
conservative and shows hesitation to adopt new technologies. A main
concern for owners, contractors or any person in charge on a job site
is the cost of the technology in question. Wireless technologies are
not cheap. There are a lot of expenses to be taken into consideration,
and a study should be completed to make sure that the importance
and savings resulting from the usage of this technology is worth the
expenses. This research attempts to assess the effectiveness of using
the appropriate wireless technologies based on criteria such as
performance, reliability, and risk. The assessment is based on a utility
function model that breaks down the selection issue into alternatives
attribute. Then the attributes are assigned weights and single
attributes are measured. Finally, single attribute are combined to
develop one single aggregate utility index for each alternative.
Abstract: We used live E. coli containing synthetic genetic
oscillators to study how the degree of synchrony between the genetic
circuits of sister cells changes with temperature. We found that both
the mean and the variability of the degree of synchrony between the
fluorescence signals from sister cells are affected by temperature.
Also, while most pairs of sister cells were found to be highly
synchronous in each condition, the number of asynchronous pairs
increased with increasing temperature, which was found to be due to
disruptions in the oscillations. Finally we provide evidence that these
disruptions tend to affect multiple generations as opposed to
individual cells. These findings provide insight in how to design
more robust synthetic circuits and in how cell division can affect their
dynamics.
Abstract: In this paper, the energy saving and human thermal
comfort in a typical office room are investigated. The impact of a
combined system of exhaust inlet air with light slots located at the
ceiling level in a room served by displacement ventilation system is
numerically modelled. Previous experimental data are used to
validate the Computational Fluid Dynamic (CFD) model. A case
study of simulated office room includes two seating occupants, two
computers, two data loggers and four lamps. The combined system is
located at the ceiling level above the heat sources. A new method of
calculation for the cooling coil load in Stratified Air Distribution
(STRAD) system is used in this study. The results show that 47.4%
energy saving of space cooling load can be achieved by combing the
exhaust inlet air with light slots at the ceiling level above the heat
sources.
Abstract: Mustard leaves are rich in folates, vitamin A, K and
B-complex. Mustard greens are low in calories and fats and rich in
dietary fiber. They are rich in potassium, manganese, iron, copper,
calcium, magnesium and low in sodium. It is very rich in antioxidants
and Phytonutrients. For the optimization of process variables
(moisture content and mustard leave powder), the experiments were
conducted according to central composite Face Centered Composite
design of RSM. The mustard leaves powder was replaced with
composite flour (a combination of rice, chickpea and corn in the ratio
of 70:15:15). The extrudate was extruded in a twin screw extruder at
a barrel temperature of 120°C. The independent variables were
mustard leaves powder (2-10 %) and moisture content (12-20 %).
Responses analyzed were bulk density, water solubility index, water
absorption index, lateral expansion, antioxidant activity, total
phenolic content, and overall acceptability. The optimum conditions
obtained were 7.19 g mustard leaves powder in 100g premix having
16.8% moisture content (w.b).
Abstract: Most of the oil palm plantations have been threatened
by Basal Stem Rot (BSR) disease which causes serious economic
impact. This study was conducted to identify the healthy and BSRinfected
oil palm tree using thirteen color indices. Multispectral and
thermal camera was used to capture 216 images of the leaves taken
from frond number 1, 9 and 17. Indices of normalized difference
vegetation index (NDVI), red (R), green (G), blue (B), near infrared
(NIR), green – blue (GB), green/blue (G/B), green – red (GR),
green/red (G/R), hue (H), saturation (S), intensity (I) and thermal
index (T) were used. From this study, it can be concluded that G
index taken from frond number 9 is the best index to differentiate
between the healthy and BSR-infected oil palm trees. It not only gave
high value of correlation coefficient (R=-0.962), but also high value
of separation between healthy and BSR-infected oil palm tree.
Furthermore, power and S model developed using G index gave the
highest R2 value which is 0.985.
Abstract: This paper presents Carrier Sense Multiple Access
(CSMA) communication models based on SoC design methodology.
Such a model can be used to support the modeling of the complex
wireless communication systems. Therefore, the use of such
communication model is an important technique in the construction
of high-performance communication. SystemC has been chosen
because it provides a homogeneous design flow for complex designs
(i.e. SoC and IP-based design). We use a swarm system to validate
CSMA designed model and to show how advantages of incorporating
communication early in the design process. The wireless
communication created through the modeling of CSMA protocol that
can be used to achieve communication between all the agents and to
coordinate access to the shared medium (channel).
Abstract: Interstitial free steels possess better formability and
have many applications in automotive industries. Forming limit
diagrams (FLDs) indicate the formability of materials which can be
determined by experimental and finite element (FE) simulations.
FLDs were determined experimentally by LDH test, utilizing optical
strain measurement system for measuring the strains in different
width specimens and by FE simulations in Interstitial Free (IF) and
Interstitial Free High Strength (IFHS) steels. In this study, the
experimental and FE simulated FLDs are compared and also the
stress based FLDs were investigated.
Abstract: Today architecture has become as a powerful media
for introducing cultures to the world, which in turn brings about a
change in the global insight, power gaining, investment, and
development. Islamic architecture is based on the language of Koran
and shows the depth and richness of Islam through the spiritual soul.
This is in a way that belief in monotheism and faith in Islamic
teachings are manifested as Islam's aesthetic thought in Islamic
architecture. Unfortunately, Islamic architecture has been damaged a
lot due to the lack of the necessary information, and also successive
wars that have overtaken the Moslems as well as the dominance of
colonizing counties.
Islamic architecture is rooted in the history, culture and
civilization of Moslems, but its deficiencies and shortcomings should
be removed through systematizing the Islamic architecture
researchers. Islamic countries should act in a way that the art of
Islamic architecture shows its true place in different architecture eras
and makes everybody aware that Islamic architecture has a historical
root and is connected eternally to the genuineness, religious art, and
Moslems' culture and civilization.
Abstract: Remote arid areas of the vast expanses of the African
deserts hold huge subterranean reserves of brackish water resources
waiting for economic development. This work presents design
guidelines as well as initial performance data of new autonomous
solar desalination equipment which could help local communities
produce their own fresh water using solar energy only and, why not,
contribute to transforming desert lands into lush gardens. The output
of solar distillation equipments are typically low and in the range of 3
l/m2/day on the average. This new design with an integrated, water
based, environmentally-friendly solar heat storage system produced 5
l/m2/day in early spring weather. Equipment output during summer
exceeded 9 liters per m2 per day.
Abstract: This paper presents the ‘Eye Ball Motion Controlled
Wheelchair using IR Sensors’ for the elderly and differently abled
people. In this eye tracking based technology, three Proximity
Infrared (IR) sensor modules are mounted on an eye frame to trace
the movement of the iris. Since, IR sensors detect only white objects;
a unique sequence of digital bits is generated corresponding to each
eye movement. These signals are then processed via a micro
controller IC (PIC18F452) to control the motors of the wheelchair.
The potential and efficiency of previously developed rehabilitation
systems that use head motion, chin control, sip-n-puff control, voice
recognition, and EEG signals variedly have also been explored in
detail. They were found to be inconvenient as they served either
limited usability or non-affordability. After multiple regression
analyses, the proposed design was developed as a cost-effective,
flexible and stream-lined alternative for people who have trouble
adopting conventional assistive technologies.
Abstract: This paper presents an application of Artificial Neural
Network (ANN) algorithm for improving power system voltage
stability. The training data is obtained by solving several normal and
abnormal conditions using the Linear Programming technique. The
selected objective function gives minimum deviation of the reactive
power control variables, which leads to the maximization of
minimum Eigen value of load flow Jacobian. The considered reactive
power control variables are switchable VAR compensators, OLTC
transformers and excitation of generators. The method has been
implemented on a modified IEEE 30-bus test system. The results
obtain from the test clearly show that the trained neural network is
capable of improving the voltage stability in power system with a
high level of precision and speed.
Abstract: This study found that most corporate personnel are
using social media to communicate with colleagues to make the
process of working more efficient. Complete satisfaction occurred on
the use of security within the University’s computer network. The
social network usage for communication, collaboration,
entertainment and demonstrating concerns accounted for fifty percent
of variance to predict interpersonal relationships of corporate
personnel. This evaluation on the effectiveness of social networking
involved 213 corporate personnel’s. The data was collected by
questionnaires. This data was analyzed by using percentage, mean,
and standard deviation.
The results from the analysis and the effectiveness of using online
social networks were derived from the attitude of private users and
safety data within the security system. The results showed that the
effectiveness on the use of an online social network for corporate
personnel of Suan Sunandha Rajabhat University was specifically at
a good level, and the overall effects of each aspect was (Ẋ=3.11).
Abstract: Land Use Land Cover (LULC) changes due to human
activities and natural causes have become a major environmental
concern. Assessment of temporal remote sensing data provides
information about LULC impacts on environment. Land Surface
Temperature (LST) is one of the important components for modeling
environmental changes in climatological, hydrological, and
agricultural studies. In this study, LULC changes (September 7, 1984
and July 8, 2014) especially in agricultural lands together with
population changes (1985-2014) and LST status were investigated
using remotely sensed and census data in South Marmara Watershed,
Turkey. LULC changes were determined using Landsat TM and
Landsat OLI data acquired in 1984 and 2014 summers. Six-band TM
and OLI images were classified using supervised classification
method to prepare LULC map including five classes including Forest
(F), Grazing Land (G), Agricultural Land (A), Water Surface (W),
Residential Area-Bare Soil (R-B) classes. The LST image was also
derived from thermal bands of the same dates.
LULC classification results showed that forest areas, agricultural
lands, water surfaces and residential area-bare soils were increased as
65751 ha, 20163 ha, 1924 ha and 20462 ha respectively. In
comparison, a dramatic decrement occurred in grazing land (107985
ha) within three decades. The population increased 29% between
years 1984-2014 in whole study area. Along with the natural causes,
migration also caused this increase since the study area has an
important employment potential. LULC was transformed among the
classes due to the expansion in residential, commercial and industrial
areas as well as political decisions. In the study, results showed that
agricultural lands around the settlement areas transformed to
residential areas in 30 years.
The LST images showed that mean temperatures were ranged
between 26-32°C in 1984 and 27-33°C in 2014. Minimum
temperature of agricultural lands was increased 3°C and reached to
23°C. In contrast, maximum temperature of A class decreased to
41°C from 44°C. Considering temperatures of the 2014 R-B class and
1984 status of same areas, it was seen that mean, min and max
temperatures increased by 2°C.
As a result, the dynamism of population, LULC and LST resulted
in increasing mean and maximum surface temperatures, living
spaces/industrial areas and agricultural lands.