Abstract: Evapotranspiration is one of the most important
components of the hydrological cycle. Evapotranspiration (ETo) is an
important variable in water and energy balances on the earth’s
surface, and knowledge of the distribution of ET is a key factor in
hydrology, climatology, agronomy and ecology studies. Many
researchers have a valid relationship, which is a function of climate
factors, to estimate the potential evapotranspiration presented to the
plant water stress or water loss, prevent. The FAO-Penman method
(PM) had been recommended as a standard method. This method
requires many data and these data are not available in every area of
world. So, other methods should be evaluated for these conditions.
When sufficient or reliable data to solve the PM equation are not
available then Hargreaves equation can be used. The Hargreaves
equation (HG) requires only daily mean, maximum and minimum air
temperature extraterrestrial radiation .In this study, Hargreaves
method (HG) were evaluated in 12 stations in the North West region
of Iran. Results of HG and M.HG methods were compared with
results of PM method. Statistical analysis of this comparison showed
that calibration process has had significant effect on efficiency of
Hargreaves method.
Abstract: In recent years, multi-antenna techniques are being considered as a potential solution to increase the flow of future wireless communication systems. The objective of this article is to study the emission and reception system MIMO (Multiple Input Multiple Output), and present the different reception decoding techniques. First we will present the least complex technical, linear receivers such as the zero forcing equalizer (ZF) and minimum mean squared error (MMSE). Then a nonlinear technique called ordered successive cancellation of interferences (OSIC) and the optimal detector based on the maximum likelihood criterion (ML), finally, we simulate the associated decoding algorithms for MIMO system such as ZF, MMSE, OSIC and ML, thus a comparison of performance of these algorithms in MIMO context.
Abstract: The use of hydroelectric pump-storage system at large
scale, MW-size systems, is already widespread around the world.
Designed for large scale applications, pump-storage station can be
scaled-down for small, remote residential applications. Given the cost
and complexity associated with installing a substation further than
100 miles from the main transmission lines, a remote, independent
and self-sufficient system is by far the most feasible solution. This
article is aiming at the design of wind and solar power generating
system, by means of pumped-storage to replace the wind and /or solar
power systems with a battery bank energy storage. Wind and solar
pumped-storage power generating system can reduce the cost of
power generation system, according to the user's electricity load and
resource condition and also can ensure system reliability of power
supply. Wind and solar pumped-storage power generation system is
well suited for remote residential applications with intermittent wind
and/or solar energy. This type of power systems, installed in these
locations, could be a very good alternative, with economic benefits
and positive social effects. The advantage of pumped storage power
system, where wind power regulation is calculated, shows that a
significant smoothing of the produced power is obtained, resulting in
a power-on-demand system’s capability, concomitant to extra
economic benefits.
Abstract: Implementation of advanced technologies requires
sophisticated instruments that deal with the operation, control,
restoration and protection of rapidly growing power system network
under normal and abnormal conditions. Presently, the applications of
Phasor Measurement Unit (PMU) are widely found in real time
operation, monitoring, controlling and analysis of power system
network as it eliminates the various limitations of supervisory control
and data acquisition system (SCADA) conventionally used in power
system. The use of PMU data is very rapidly increasing its
importance for online and offline analysis. Wide area measurement
system (WAMS) is developed as new technology by use of multiple
PMUs in power system. The present paper proposes a model of
Matlab based PMU using Discrete Fourier Transform (DFT)
algorithm and evaluation of its operation under different
contingencies. In this paper, PMU based two bus system having
WAMS network is presented as a case study.
Abstract: Perception, evaluation and representation of the
environment have been the subject of many disciplines including
psychology, geography and architecture. In environmental and social
psychology literature there are several evidences which suggest that
cognitive representations about a place consisted of not only
geographic items but also social and cultural. Mental representations
of residence area or a country are influenced and determined by
social-demographics, the physical and social context. Thus, all
mental representations of a given place are also social
representations. Cognitive maps are the main and common
instruments that are used to identify spatial images and the difference
between physical and subjective environments. The aim of the
current study is investigating the mental and social representations of
Turkey in university students’ minds. Data was collected from 249
university students from different departments (i.e. psychology,
geography, history, tourism departments) of Ege University.
Participants were requested to reflect Turkey in their mind onto the
paper drawing sketch maps. According to the results, cognitive maps
showed geographic aspects of Turkey as well as the context of
symbolic, cultural and political reality of Turkey. That is to say, these
maps had many symbolic and verbal items related to critics on social
and cultural problems, ongoing ethnic and political conflicts, and
actual political agenda of Turkey. Additionally, one of main
differentiations in these representations appeared in terms of the East
and West side of the Turkey, and the representations of the East and
West was varied correspondingly participants’ cultural background,
their ethnic values, and where they have born. The results of the
study were discussed in environmental and social psychological
perspective considering cultural and social values of Turkey and
current political circumstances of the country.
Abstract: The new era of digital communication has brought up
many challenges that network operators need to overcome. The high
demand of mobile data rates require improved networks, which is a
challenge for the operators in terms of maintaining the quality of
experience (QoE) for their consumers. In live video transmission,
there is a sheer need for live surveillance of the videos in order to
maintain the quality of the network. For this purpose objective
algorithms are employed to monitor the quality of the videos that are
transmitted over a network. In order to test these objective algorithms,
subjective quality assessment of the streamed videos is required, as the
human eye is the best source of perceptual assessment. In this paper we
have conducted subjective evaluation of videos with varying spatial
and temporal impairments. These videos were impaired with frame
freezing distortions so that the impact of frame freezing on the quality
of experience could be studied. We present subjective Mean Opinion
Score (MOS) for these videos that can be used for fine tuning the
objective algorithms for video quality assessment.
Abstract: Fibre cement plates, often used in construction,
generally are made using quartz as an inert material, cement as a
binder and cellulose as a fibre. This paper, first of all, investigates the
mechanical properties and durability of fibre cement plates when
quartz is both partly and fully replaced with diatomite. Diatomite
does not only have lower density compared to quartz but also has
high pozzolanic activity. The main objective of this paper is the
investigation of the effects of supplementary cementing materials
(SCMs) on the short and long term mechanical properties and
durability characteristics of fibre cement plates prepared using
diatomite. Supplementary cementing materials such as ground
granulated blast furnace slug (GGBS) and fly ash (FA) are used in
this study. Volume proportions of 10, 20, 30 and 40% of GGBS and
FA are used as partial replacement materials to cement. Short and
long term mechanical properties such as compressive and flexural
strengths as well as sorptivity characteristics and mass were
investigated. Consistency and setting time at each replacement levels
of SCMs were also recorded. The effects of using supplementary
cementing materials on the carbonation and sulphate resistance of
fibre cement plates were then experimented. The results, first of all,
show that the use of diatomite as a full or partial replacement to
quartz resulted in a systematic decrease in total mass of the fibre
cement plates. The reduction of mass was largely due to the lower
density and finer particle size of diatomite compared to quartz. The
use of diatomite did not only reduce the mass of these plates but also
increased the compressive strength significantly as a result of its high
pozzolanic activity. The replacement levels of both GGBS and FA
resulted in a systematic decrease in short term compressive strength
with increasing replacement levels. This was essentially expected as
the total rate of hydration is much lower in GGBS and FA than that
of cement. Long term results however, indicated that the compressive
strength of fibre cement plates prepared using both GGBS and FA
increases with time and hence the compressive strength of plates
prepared using SCMs is either equivalent or more than the
compressive strength of plates prepared using cement alone.
Durability characteristics of fibre cement plates prepared using SCMs
were enhanced significantly. Measurements of sopritivty
characteristics were also indicated that the plates prepared using
SCMs has much lower water absorption capacities compared to
plates prepared cement alone. Much higher resistance to carbonation
and sulphate attach were observed with plates prepared using SCMs.
The results presented in this paper show that the use of SCMs does
not only support the production of more sustainable construction
materials but also enhances the mechanical properties and durability
characteristics of fibre cement plates.
Abstract: This paper presents a new automatic vehicle detection
method from very high resolution aerial images to measure traffic
density. The proposed method starts by extracting road regions from
image using road vector data. Then, the road image is divided into
equal sections considering resolution of the images. Gradient vectors
of the road image are computed from edge map of the corresponding
image. Gradient vectors on the each boundary of the sections are
divided where the gradient vectors significantly change their
directions. Finally, number of vehicles in each section is carried out
by calculating the standard deviation of the gradient vectors in each
group and accepting the group as vehicle that has standard deviation
above predefined threshold value. The proposed method was tested in
four very high resolution aerial images acquired from Istanbul,
Turkey which illustrate roads and vehicles with diverse
characteristics. The results show the reliability of the proposed
method in detecting vehicles by producing 86% overall F1 accuracy
value.
Abstract: Continuous upflow filters can combine the nutrient
(nitrogen and phosphate) and suspended solid removal in one unit
process. The contaminant removal could be achieved chemically or
biologically; in both processes the filter removal efficiency depends
on the interaction between the packed filter media and the influent. In
this paper a residence time distribution (RTD) study was carried out
to understand and compare the transfer behaviour of contaminants
through a selected filter media packed in a laboratory-scale
continuous up flow filter; the selected filter media are limestone and
white dolomite. The experimental work was conducted by injecting a
tracer (red drain dye tracer –RDD) into the filtration system and then
measuring the tracer concentration at the outflow as a function of
time; the tracer injection was applied at hydraulic loading rates
(HLRs) (3.8 to 15.2 m h-1). The results were analysed according to
the cumulative distribution function F(t) to estimate the residence
time of the tracer molecules inside the filter media. The mean
residence time (MRT) and variance σ2 are two moments of RTD that
were calculated to compare the RTD characteristics of limestone with
white dolomite. The results showed that the exit-age distribution of
the tracer looks better at HLRs (3.8 to 7.6 m h-1) and (3.8 m h-1) for
limestone and white dolomite respectively. At these HLRs the
cumulative distribution function F(t) revealed that the residence time
of the tracer inside the limestone was longer than in the white
dolomite; whereas all the tracer took 8 minutes to leave the white
dolomite at 3.8 m h-1. On the other hand, the same amount of the
tracer took 10 minutes to leave the limestone at the same HLR. In
conclusion, the determination of the optimal level of hydraulic
loading rate, which achieved the better influent distribution over the
filtration system, helps to identify the applicability of the material as
filter media. Further work will be applied to examine the efficiency
of the limestone and white dolomite for phosphate removal by
pumping a phosphate solution into the filter at HLRs (3.8 to 7.6 m h-1).
Abstract: Model predictive control is a kind of optimal feedback
control in which control performance over a finite future is optimized
with a performance index that has a moving initial time and a moving
terminal time. This paper examines the stability of model predictive
control for linear discrete-time systems with additive stochastic
disturbances. A sufficient condition for the stability of the closed-loop
system with model predictive control is derived by means of a linear
matrix inequality. The objective of this paper is to show the results
of computational simulations in order to verify the effectiveness of
the obtained stability condition.
Abstract: Dynamics of a rotor supported by air bearings is
strongly depends on the pressure distribution between the rotor and
the bearing. In this study, internal pressure in air bearings is
numerical and experimental analyzed for different radial clearances.
Firstly the pressure distribution between rotor and bearing is modeled
using Reynold's equation and this model is solved numerically. The
rotor-bearing system is also modeled in four degree of freedom and it
is simulated for different radial clearances. Then, in order to validate
numerical results, a test rig is designed and the rotor bearing system
is run under the same operational conditions. Pressure signals of left
and right bearings are recorded. Internal pressure variations are
compared for numerical and experimental results for different radial
clearances.
Abstract: This paper presents development results of usage of
C-OTDR monitoring systems for rail traffic management. The COTDR
method is based on vibrosensitive properties of optical fibers.
Analysis of Rayleigh backscattering radiation parameters changes
which take place due to microscopic seismoacoustic impacts on the
optical fiber allows to determine seismoacoustic emission source
positions and to identify their types. This approach proved successful
for rail traffic management (moving block system, weigh- in-motion
system etc.).
Abstract: In the field of fashion design, 3D Mannequin is a kind
of assisting tool which could rapidly realize the design concepts.
While the concept of 3D Mannequin is applied to the computer added
fashion design, it will connect with the development and the
application of design platform and system. Thus, the situation
mentioned above revealed a truth that it is very critical to develop a
module of 3D Mannequin which would correspond with the necessity
of fashion design. This research proposes a concrete plan that
developing and constructing a system of 3D Mannequin with Kinect.
In the content, ergonomic measurements of objective human features
could be attained real-time through the implement with depth camera
of Kinect, and then the mesh morphing can be implemented through
transformed the locations of the control-points on the model by
inputting those ergonomic data to get an exclusive 3D mannequin
model. In the proposed methodology, after the scanned points from the
Kinect are revised for accuracy and smoothening, a complete human
feature would be reconstructed by the ICP algorithm with the method
of image processing. Also, the objective human feature could be
recognized to analyze and get real measurements. Furthermore, the
data of ergonomic measurements could be applied to shape morphing
for the division of 3D Mannequin reconstructed by feature curves. Due
to a standardized and customer-oriented 3D Mannequin would be
generated by the implement of subdivision, the research could be
applied to the fashion design or the presentation and display of 3D
virtual clothes. In order to examine the practicality of research
structure, a system of 3D Mannequin would be constructed with JAVA
program in this study. Through the revision of experiments the
practicability-contained research result would come out.
Abstract: UAV’s are small remote operated or automated aerial
surveillance systems without a human pilot aboard. UAV’s generally
finds its use in military and special operation application, a recent
growing trend in UAV’s finds its application in several civil and nonmilitary
works such as inspection of power or pipelines. The
objective of this paper is the augmentation of a UAV in order to
replace the existing expensive sonar (Sound Navigation And
Ranging) based equipment amongst small scale fisherman, for whom
access to sonar equipment are restricted due to limited economic
resources. The surveillance equipment’s present in the UAV will
relay data and GPS (Global Positioning System) location onto a
receiver on the fishing boat using RF signals, using which the
location of the schools of fishes can be found. In addition to this, an
emergency beacon system is present for rescue operations and drone
recovery.
Abstract: This study, for its research subjects, uses patients who
had undergone total knee replacement surgery from the database of the
National Health Insurance Administration. Through the review of
literatures and the interviews with physicians, important factors are
selected after careful screening. Then using Cross Entropy Method,
Genetic Algorithm Logistic Regression, and Particle Swarm
Optimization, the weight of each factor is calculated and obtained. In
the meantime, Excel VBA and Case Based Reasoning are combined
and adopted to evaluate the system. Results show no significant
difference found through Genetic Algorithm Logistic Regression and
Particle Swarm Optimization with over 97% accuracy in both
methods. Both ROC areas are above 0.87. This study can provide
critical reference to medical personnel as clinical assessment to
effectively enhance medical care quality and efficiency, prevent
unnecessary waste, and provide practical advantages to resource
allocation to medical institutes.
Abstract: In this paper a new model for center of motion
creating is proposed. This new method uses cables. So, it is very
useful in robots because it is light and has easy assembling process.
In the robots which need to be in touch with some things this method
is so useful. It will be described in the following. The accuracy of the
idea is proved by two experiments. This system could be used in the
robots which need a fixed point in the contact with some things and
make a circular motion.
Abstract: Socio-economic development, which is seen around
the world today, has contributed to the emergence of new problems
of a social nature. Different political, historical, geographical or
economic conditions cause that, in addition to global issues of social
policy such as an aging population, unemployment, migration,
countries, regions, there are also specific new problems that require
diagnosis, individualized approach and efficient, planned solutions.
These should include, among others, digital addiction, peer violence,
obesity among children, the problem of ‘legal highs’, stress,
depression, diseases associated with environmental pollution etc. The
central authorities, selected most often with the tools specific to
representative democracy, that is, the general election, for many
reasons, inter alia, organizational, communication, are not able to
effectively diagnose their intensity, territorial distribution, and thus to
effectively fight them. This article aims to show how in Poland,
citizens influence solving problems related to the broader social
policy implemented at the local government level and indicates the
possibilities of improving those solutions. The conclusions of
theoretical analysis have been supported by empirical studies, which
tested the use of instruments of participatory democracy in the
planning and creation of communal strategies for solving social
problems in one of the Polish voivodeships.
Abstract: In recent years a new method of combination
treatment for cancer has been developed and studied that has led to
significant advancements in the field of cancer therapy. Hyperthermia
is a traditional therapy that, along with a creation of a medically
approved level of heat with the help of an alternating magnetic AC
current, results in the destruction of cancer cells by heat. This paper
gives details regarding the production of the spherical nanocomposite
PVA/γ-Fe2O3 in order to be used for medical purposes such as tumor
treatment by hyperthermia. To reach a suitable and evenly distributed
temperature, the nanocomposite with core-shell morphology and
spherical form within a 100 to 200 nanometer size was created using
phase separation emulsion, in which the magnetic nano-particles γ-
Fe2O3 with an average particle size of 20 nano-meters and with
different percentages of 0.2, 0.4, 0.5 and 0.6 were covered by
polyvinyl alcohol. The main concern in hyperthermia and heat
treatment is achieving desirable specific absorption rate (SAR) and
one of the most critical factors in SAR is particle size. In this project
all attempts has been done to reach minimal size and consequently
maximum SAR. The morphological analysis of the spherical
structure of the nanocomposite PVA/γ-Fe2O3 was achieved by SEM
analyses and the study of the chemical bonds created was made
possible by FTIR analysis. To investigate the manner of magnetic
nanocomposite particle size distribution a DLS experiment was
conducted. Moreover, to determine the magnetic behavior of the γ-
Fe2O3 particle and the nanocomposite PVA/γ-Fe2O3 in different
concentrations a VSM test was conducted. To sum up, creating
magnetic nanocomposites with a spherical morphology that would be
employed for drug loading opens doors to new approaches in
developing nanocomposites that provide efficient heat and a
controlled release of drug simultaneously inside the magnetic field,
which are among their positive characteristics that could significantly
improve the recovery process in patients.
Abstract: This paper describes the main features of a knowledge-based system evaluation method. System evaluation is placed in the context of a hybrid legal decision-support system, Advisory Support for Home Settlement in Divorce (ASHSD). Legal knowledge for ASHSD is represented in two forms, as rules and previously decided cases. Besides distinguishing the two different forms of knowledge representation, the paper outlines the actual use of these forms in a computational framework that is designed to generate a plausible solution for a given case, by using rule-based reasoning (RBR) and case-based reasoning (CBR) in an integrated environment. The nature of suitability assessment of a solution has been considered as a multiple criteria decision-making process in ASHAD evaluation. The evaluation was performed by a combination of discussions and questionnaires with different user groups. The answers to questionnaires used in this evaluations method have been measured as a fuzzy linguistic term. The finding suggests that fuzzy linguistic evaluation is practical and meaningful in knowledge-based system development purpose.
Abstract: This paper presents an experimental study on
structural performance of an innovative noise barrier consisting of
poly-block, light polyurethane foam (LPF) and polyurea. This wall
system (flexi-wall) is intended to be employed as a vertical extension
to existing sound barriers in an accelerated construction method. To
aid in the wall design, several mechanical tests were conducted on
LPF specimens and two full-scale walls were then fabricated
employing the same LPF material. The full-scale walls were
subjected to lateral loading in order to establish their lateral
resistance. A cyclic fatigue test was also performed on a full-scale
flexi-wall in order to evaluate the performance of the wall under a
repetitive loading condition. The result of the experiments indicated
the suitability of flexi-wall in accelerated construction and confirmed
that the structural performance of the wall system under lateral
loading is satisfactory for the sound barrier application. The
experimental results were discussed and a preliminary design
procedure for application of flexi-wall in sound barrier applications
was also developed.