Abstract: In recent research copper and manganese systems
were found to be the most active in CO and organic compounds
oxidation among the base catalysts. The mixed copper manganese
oxide has been widely studied in oxidation reactions because of their
higher activity at low temperatures in comparison with single oxide
catalysts. The results showed that the formation of spinel
CuxMn3−xO4 in the oxidized catalyst is responsible for the activity
even at room temperature. That is why the most of the investigations
are focused on the hopcalite catalyst (CuMn2O4) as the best coppermanganese
catalyst. Now it’s known that this is true only for CO
oxidation, but not for mixture of CO and VOCs. The purpose of this
study is to investigate the alumina supported copper-manganese
catalysts with different Cu/Mn molar ratio in terms of oxidation of
CO, methanol and dimethyl ether. The catalysts were prepared by impregnation of γ-Al2O3 with
copper and manganese nitrates and the catalytic activity
measurements were carried out in two stage continuous flow
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions closest possible to the industrial. Gas
mixtures on the input and output of the reactor were analyzed with a
gas chromatograph, equipped with FID and TCD detectors. The
texture characteristics were determined by low-temperature (- 196oС)
nitrogen adsorption in a Quantachrome Instruments NOVA 1200e
(USA) specific surface area & pore analyzer. Thermal, XRD and
TPR analyses were performed. It was established that the active component of the mixed Cu-
Mn/γ–alumina catalysts strongly depends on the Cu/Mn molar ratio.
Highly active alumina supported Cu-Mn catalysts for CO, methanol
and DME oxidation were synthesized. While the hopcalite is the best
catalyst for CO oxidation, the best compromise for simultaneous
oxidation of all components is the catalyst with Cu/Mn molar ratio
1:5.
Abstract: In this paper air quality conditions in Makkah and
Leeds are compared. These two cities have totally different climatic
conditions. Makkah climate is characterised as hot and dry (arid)
whereas that of Leeds is characterised as cold and wet (temperate).
This study uses air quality data from 2012 collected in Makkah,
Saudi Arabia and Leeds, UK. The concentrations of all pollutants,
except NO are higher in Makkah. Most notable, the concentrations of
PM10 are much higher in Makkah than in Leeds. This is probably due
to the arid nature of climatic conditions in Makkah and not solely due
to anthropogenic emission sources, otherwise like PM10 some of the
other pollutants, such as CO, NO, and SO2 would have shown much
greater difference between Leeds and Makkah. Correlation analysis is
performed between different pollutants at the same site and the same
pollutants at different sites. In Leeds the correlation between PM10
and other pollutants is significantly stronger than in Makkah. Weaker
correlation in Makkah is probably due to the fact that in Makkah
most of the gaseous pollutants are emitted by combustion processes,
whereas most of the PM10 is generated by other sources, such as
windblown dust, re-suspension, and construction activities. This is in
contrast to Leeds where all pollutants including PM10 are
predominantly emitted by combustions, such as road traffic.
Furthermore, in Leeds frequent rains wash out most of the
atmospheric particulate matter and suppress re-suspension of dust.
Temporal trends of various pollutants are compared and discussed.
This study emphasises the role of climatic conditions in managing air
quality, and hence the need for region-specific controlling strategies
according to the local climatic and meteorological conditions.
Abstract: Background subtraction and temporal difference are
often used for moving object detection in video. Both approaches are
computationally simple and easy to be deployed in real-time image
processing. However, while the background subtraction is highly
sensitive to dynamic background and illumination changes, the
temporal difference approach is poor at extracting relevant pixels of
the moving object and at detecting the stopped or slowly moving
objects in the scene. In this paper, we propose a simple moving object
detection scheme based on adaptive background subtraction and
temporal difference exploiting dynamic background updates. The
proposed technique consists of histogram equalization, a linear
combination of background and temporal difference, followed by the
novel frame-based and pixel-based background updating techniques.
Finally, morphological operations are applied to the output images.
Experimental results show that the proposed algorithm can solve the
drawbacks of both background subtraction and temporal difference
methods and can provide better performance than that of each method.
Abstract: This paper aims to project the construction of a
prototype azimuthal thruster, mounted with materials of low cost and
easy access, testing in a controlled environment to measure their
performance, characteristics and feasibility of future projects. The
construction of the simulation of dynamic positioning software,
responsible for simulating a vessel and reposition it when necessary.
Validation tests were performed in the form of partial or complete
system. These tests validate the system manually or automatically.
The system provides an interface to the user and simulates the
conditions unfavorable positioning of a vessel, accurately calculates
the azimuth angle, the direction of rotation of the helix and the time
that this should be turned on so that the vessel back to position
original. A serial communication connects the Simulation Dynamic
Positioning System with Embedded System causing the usergenerated
data to simulate the DP system arrives in the form of
control signals to the motors of the propellant. This article addresses
issues in the marine industry employees.
Abstract: The study is in application and analysis of two tourism
management tools that can contribute to making public managers
decision: the Barometer of Tourism Sustainability (BTS) and the
Ecological Footprint (EF). The results have shown that BTS allows
you to have an integrated view of the tourism system, awakening to
the need for planning of appropriate actions so that it can achieve the
positive scale proposed (potentially sustainable). Already the
methodology of ecological tourism footprint is an important tool to
measure potential impacts generated by tourism to tourist reality.
Abstract: The purpose of this paper is to present a modeling and
control of a quarter-car active suspension system with unknown
mass, unknown time-delay and road disturbance. The objective of
designing the controller is to derive a control law to achieve stability
of the system and convergence that can considerably improve ride
comfort and road disturbance handling. This is accomplished by
using Routh-Hurwitz criterion based on defined parameters.
Mathematical proof is given to show the ability of the designed
controller to ensure the target of design, implementation with the
active suspension system and enhancement dispersion oscillation of
the system despite these problems. Simulations were also performed
to control quarter car suspension, where the results obtained from
these simulations verify the validity of the proposed design.
Abstract: Contemporary theories of sustainability, concerning
the natural and built environment, have recently introduced an
environmental attitude towards the architectural design that, in turn,
affects the practice of conservation and reuse of the existing building
stock. This paper presents an environmentally friendly approach
towards the conservation of vernacular architecture and it is based on
the results of a research program which involved the investigation of
sustainable design elements of traditional buildings in Cyprus. The
research in question showed that Cypriot vernacular architecture gave
more emphasis on cooling rather than heating strategies. Another
notable finding of the investigation was the great importance given to
courtyards as they enhance considerably, and in various ways, the
microclimatic conditions of the immediate environment with
favorable results throughout the year. Moreover, it was shown that
the reduction in temperature fluctuation observed in the closed and
semi-open spaces, compared to the respective temperature fluctuation
of the external environment -due to the thermal inertia of the building
envelope- helps towards the achievement of more comfortable living
conditions within traditional dwellings. This paper concludes with a
proposal of a sustainable approach towards the conservation of the
existing environment and the introduction of new environmental
criteria for the conservation of traditional buildings, beyond the
aesthetic, morphological and structural ones that are generally
applied.
Abstract: This paper presents the design, development and
evaluation of an application prototype developed to support
tuberculosis (TB) patients’ treatment adherence. The system makes
use of graphics and voice reminders as opposed to text messaging to
encourage patients to follow their medication routine. To evaluate the
effect of the prototype applications, participants were given mobile
phones on which the reminder system was installed. Thirty-eight
people, including TB health workers and patients from Zanzibar,
Tanzania, participated in the evaluation exercises. The results
indicate that the participants found the mobile image-based
application is useful to support TB treatment. All participants
understood and interpreted the intended meaning of every image
correctly. The study findings revealed that the use of a mobile visualbased
application may have potential benefit to support TB patients
(both literate and illiterate) in their treatment processes.
Abstract: SARA is a common and serious metabolic disorder in
early lactation in dairy cattle and in finishing beef cattle, caused by
diets with high inclusion of cereal grain. This experiment was
performed to determine the efficacy of Megasphaera elsdenii, a
major lactate-utilizing bacterium in prevention/treatment of SARA in
vivo. In vivo experimentation, it was used eight ruminally cannulated
rams and it was applied the rapid adaptation with the mixture of grain
based on wheat (80% wheat, 20% barley) and barley (80% barley,
20% wheat). During the systematic adaptation, it was followed the
probability of SARA formation by being measured the rumen pH
with two hours intervals after and before feeding. After being
evaluated the data, it was determined the ruminal pH ranged from
5.2-5.6 on the condition of feeding with 60 percentage of grain
mixture based on barley and wheat, that assured the definite form of
subacute acidosis. In four days SARA period, M. elsdenii (1010 cfu
ml-1) was inoculated during the first two days. During the SARA
period, it was observed the decrease of feed intake with M. elsdenii
inoculation. Inoculation of M. elsdenii was caused to differentiation
of rumen pH (P
Abstract: The work aims to develop a robot in the form of
autonomous vehicle to detect, inspection and mapping of
underground pipelines through the ATmega328 Arduino platform.
Hardware prototyping is very similar to C / C ++ language that
facilitates its use in robotics open source, resembles PLC used in
large industrial processes. The robot will traverse the surface
independently of direct human action, in order to automate the
process of detecting buried pipes, guided by electromagnetic
induction. The induction comes from coils that send the signal to the
Arduino microcontroller contained in that will make the difference in
intensity and the treatment of the information, and then this
determines actions to electrical components such as relays and
motors, allowing the prototype to move on the surface and getting the
necessary information. This change of direction is performed by a
stepper motor with a servo motor. The robot was developed by
electrical and electronic assemblies that allowed test your application.
The assembly is made up of metal detector coils, circuit boards and
microprocessor, which interconnected circuits previously developed
can determine, process control and mechanical actions for a robot
(autonomous car) that will make the detection and mapping of buried
pipelines plates. This type of prototype can prevent and identifies
possible landslides and they can prevent the buried pipelines suffer an
external pressure on the walls with the possibility of oil leakage and
thus pollute the environment.
Abstract: Greenhouses offer us suitable conditions which can
be controlled easily for the growth of the plant and they are made by
using a covering material that allows the sun light entering into the
system. Covering material can be glass, fiber glass, plastic or another
transparent element. This study investigates the solar energy usability
rates and solar energy benefitting rates of a semi-spherical (modified
arch) type greenhouse system according to different orientations and
positions which exists under climatic conditions of Bayburt. In the
concept of this study it is tried to determine the best direction and
best sizes of a semi-spherical greenhouse to get best solar benefit
from the sun. To achieve this aim a modeling study is made by using
MATLAB. However, this modeling study is run for some determined
shapes and greenhouses it can be used for different shaped
greenhouses or buildings. The basic parameters are determined as
greenhouse azimuth angle, the rate of size of long edge to short and
seasonal solar energy gaining of greenhouse. The optimum azimuth
angles of 400, 300, 250, 200, 150, 100, 50 m2 modified arch
greenhouse are 90o, 90o, 35o, 35o, 34o, 33o and 22o while their
optimum k values (ratio of length to width) are 10, 10, 10, 10, 6, 4
and 4 respectively. Positioning the buildings in order to get more
solar heat energy in winter and less in summer brings out energy and
money savings and increases the comfort.
Abstract: This study suggests the estimation method of stress
distribution for the beam structures based on TLS (Terrestrial Laser
Scanning). The main components of method are the creation of the
lattices of raw data from TLS to satisfy the suitable condition and
application of CSSI (Cubic Smoothing Spline Interpolation) for
estimating stress distribution. Estimation of stress distribution for the
structural member or the whole structure is one of the important
factors for safety evaluation of the structure. Existing sensors which
include ESG (Electric strain gauge) and LVDT (Linear Variable
Differential Transformer) can be categorized as contact type sensor
which should be installed on the structural members and also there are
various limitations such as the need of separate space where the
network cables are installed and the difficulty of access for sensor
installation in real buildings. To overcome these problems inherent in
the contact type sensors, TLS system of LiDAR (light detection and
ranging), which can measure the displacement of a target in a long
range without the influence of surrounding environment and also get
the whole shape of the structure, has been applied to the field of
structural health monitoring. The important characteristic of TLS
measuring is a formation of point clouds which has many points
including the local coordinate. Point clouds are not linear distribution
but dispersed shape. Thus, to analyze point clouds, the interpolation is
needed vitally. Through formation of averaged lattices and CSSI for
the raw data, the method which can estimate the displacement of
simple beam was developed. Also, the developed method can be
extended to calculate the strain and finally applicable to estimate a
stress distribution of a structural member. To verify the validity of the
method, the loading test on a simple beam was conducted and TLS
measured it. Through a comparison of the estimated stress and
reference stress, the validity of the method is confirmed.
Abstract: Neural activity in the human brain starts from the
early stages of prenatal development. This activity or signals
generated by the brain are electrical in nature and represent not only
the brain function but also the status of the whole body. At the
present moment, three methods can record functional and
physiological changes within the brain with high temporal resolution
of neuronal interactions at the network level: the
electroencephalogram (EEG), the magnet oencephalogram (MEG),
and functional magnetic resonance imaging (fMRI); each of these has
advantages and shortcomings. EEG recording with a large number of
electrodes is now feasible in clinical practice. Multichannel EEG
recorded from the scalp surface provides very valuable but indirect
information about the source distribution. However, deep electrode
measurements yield more reliable information about the source
locations intracranial recordings and scalp EEG are used with the
source imaging techniques to determine the locations and strengths of
the epileptic activity. As a source localization method, Low
Resolution Electro-Magnetic Tomography (LORETA) is solved for
the realistic geometry based on both forward methods, the Boundary
Element Method (BEM) and the Finite Difference Method (FDM). In
this paper, we review the findings EEG- LORETA about epilepsy.
Abstract: This paper proposes a linear model for optimizing
domestic energy consumption in Romania. The particularity of the
model is that it is putting in competition both tangible technologies
and thermal insulation projects with different financing modes.
The model is optimizing the energy system by minimizing the
global discounted cost in household sector, by integrating residential
lighting, space heating, hot water, combined space heating – hot
water, as well as space cooling, in a monolithic model. Another
demand sector included is the passenger transport.
This paper focuses on space heating part, analyzing technical and
economic issues related to investment decisions to envelope and
insulate buildings, in order to minimize energy consumption.
Abstract: Brownfields are one of the most important problems
that must be solved by today's cities. The topic of this article is
description of developing a comprehensive transformation of postindustrial
area of the former iron factory national cultural heritage
lower Vítkovice. City of Ostrava used to be industrial superpower of
the Czechoslovak Republic, especially in the area of coal mining and
iron production, after declining industrial production and mining in
the 80s left many unused areas of former factories generally
brownfields and backfields. Since the late 90s we are observing how
the city officials or private entities seeking to remedy this situation.
Regeneration of brownfields is a very expensive and long-term
process. The area is now rebuilt for tourists and residents of the city
in the entertainment, cultural, and social center. It was necessary do
the reconstruction of the industrial monuments. Equally important
was the construction of new buildings, which helped reusing of the
entire complex. This is a unique example of transformation of
technical monuments and completion of necessary new objects, so
that the area could start working again and reintegrate back into the
urban system.
Abstract: A new fast growing trend in tourism is ecotourism, in
which tourists visit natural ecosystems under low impact, nonconsumptive
and locally oriented activities. Through these activities
species and habitats are maintained and typically, underdeveloped
regions are emphasized. Ecotourism provides a great alternative,
especially for rural and undeveloped area. At the same time, despite
its many benefits, it also poses many risks for the naturally protected
areas. If ecotourism is practiced improperly degradation and
irreversible damages could be the unwanted result. In addition, the
lack of MSc programs in the field of Ecotourism in Europe makes it a
necessity to be developed. Such an MSc program is being
implemented with the lead partner the Technical University of
Madrid. The entire partnership has six Universities, seven SMEs and
one National Park from seven different countries all over Europe.
The MSc will have 10 educational modules that will be available
online and will prepare professionals that will be able to implement
ecotourism in a sustainable way. Only through awareness and
education a sustainable ecotourism will be achieved in the protected
areas of Europe.
Abstract: The conventional Wi-Fi backscatter system can only
process one-to-one communication between the Wi-Fi reader and the
Wi-Fi tag. For improvement of throughput of the conventional system,
this paper proposes the multi-to-multi communication system. In the
proposed system, the interference by the multi-to-multi
communication is effectively cancelled by the orthogonal multiple
access based on the identification code of the tag. Although the
overhead is generated by the procedure for the multi-to-multi
communication, because the procedure is processed by the Wi-Fi
protocol, the overhead is insignificant for the entire communication
procedure. From the numerical results, it is confirmed that the
proposed system has nearly proportional increased throughput in
according to the number of the tag that simultaneously participates in
communication.
Abstract: It is a major challenge to build a bridge superstructure
that has long-term durability and low maintenance requirements. A
solution to this challenge may be to use new materials or to
implement new structural systems. Fiber Reinforced Polymer (FRP)
composites have continued to play an important role in solving some
of persistent problems in infrastructure applications because of its
high specific strength, light weight, and durability. In this study, the
concept of the hybrid FRP-concrete structural systems is applied to a
bridge superstructure. The hybrid FRP-concrete bridge superstructure
is intended to have durable, structurally sound, and cost effective
hybrid system that will take full advantage of the inherent properties
of both FRP materials and concrete. In this study, two hybrid FRP-concrete
bridge systems were investigated. The first system consists
of trapezoidal cell units forming a bridge superstructure. The second
one is formed by arch cells. The two systems rely on using cellular
components to form the core of the bridge superstructure, and an
outer shell to warp around those cells to form the integral unit of the
bridge. Both systems were investigated analytically by using finite
element (FE) analysis. From the rigorous FE studies, it was
concluded that first system is more efficient than the second.
Abstract: There have been rigorous research and development
of unmanned aerial vehicles in the field of search and rescue (SAR)
operation recently. UAVs reduce unnecessary human risks while
assisting rescue efforts through aerial imagery, topographic mapping
and emergency delivery. The application of UAVs in offshore and
nearshore marine SAR missions is discussed in this paper. Projects
that integrate UAV technology into their systems are introduced to
highlight the great advantages and capabilities of UAVs. Scenarios
where UAVs could provide invaluable assistance are also suggested.
Abstract: Si ion implantation was widely used to synthesize
specimens of SiO2 containing supersaturated Si and subsequent high
temperature annealing induces the formation of embedded
luminescent Si nanocrystals. In this work, the potentialities of excimer
UV-light (172 nm, 7.2 eV) irradiation and rapid thermal annealing
(RTA) to enhance the photoluminescence and to achieve low
temperature formation of Si nanocrystals have been investigated. The
Si ions were introduced at acceleration energy of 180 keV to fluence of
7.5 x 1016 ions/cm2. The implanted samples were subsequently
irradiated with an excimer-UV lamp. After the process, the samples
were rapidly thermal annealed before furnace annealing (FA).
Photoluminescence spectra were measured at various stages at the
process. We found that the luminescence intensity is strongly
enhanced with excimer-UV irradiation and RTA. Moreover, effective
visible photoluminescence is found to be observed even after FA at
900 oC, only for specimens treated with excimer-UV lamp and RTA.
We also prepared specimens of Si nanocrystals embedded in a SiO2 by
reactive pulsed laser deposition (PLD) in an oxygen atmosphere. We
will make clear the similarities and differences with the way of
preparation.