Abstract: Sewer deposits have been identified as a major cause
of dysfunctions in combined sewer systems regarding sewer
management, which induces different negative consequents resulting
in poor hydraulic conveyance, environmental damages as well as
worker’s health. In order to overcome the problematics of
sedimentation, flushing has been considered as the most operative
and cost-effective way to minimize the sediments impacts and
prevent such challenges. Flushing, by prompting turbulent wave
effects, can modify the bed form depending on the hydraulic
properties and geometrical characteristics of the conduit. So far, the
dynamics of the bed-load during high-flow events in combined sewer
systems as a complex environment is not well understood, mostly due
to lack of measuring devices capable to work in the “hostile” in
combined sewer system correctly. In this regards, a one-episode
flushing issue from an opening gate valve with weir function was
carried out in a trunk sewer in Paris to understand its cleansing
efficiency on the sediments (thickness: 0-30 cm). During more than
1h of flushing within 5 m distance in downstream of this flushing
device, a maximum flowrate and a maximum level of water have
been recorded at 5 m in downstream of the gate as 4.1 m3/s and 2.1
m respectively. This paper is aimed to evaluate the efficiency of this
type of gate for around 1.1 km (from the point -50 m to +1050 m in
downstream from the gate) by (i) determining bed grain-size
distribution and sediments evolution through the sewer channel, as
well as their organic matter content, and (ii) identifying sections that
exhibit more changes in their texture after the flush. For the first one,
two series of sampling were taken from the sewer length and then
analyzed in laboratory, one before flushing and second after, at same
points among the sewer channel. Hence, a non-intrusive sampling
instrument has undertaken to extract the sediments smaller than the
fine gravels. The comparison between sediments texture after the
flush operation and the initial state, revealed the most modified zones
by the flush effect, regarding the sewer invert slope and hydraulic
parameters in the zone up to 400 m from the gate. At this distance,
despite the increase of sediment grain-size rages, D50 (median grainsize)
varies between 0.6 mm and 1.1 mm compared to 0.8 mm and 10
mm before and after flushing, respectively. Overall, regarding the
sewer channel invert slope, results indicate that grains smaller than
sands (< 2 mm) are more transported to downstream along about 400
m from the gate: in average 69% before against 38% after the flush
with more dispersion of grain-sizes distributions. Furthermore, high
effect of the channel bed irregularities on the bed material evolution
has been observed after the flush.
Abstract: This paper discusses the propagation of sound waves in
air, specifically in narrow rectangular pathways of an occluded-ear
simulator for acoustic measurements. In narrow pathways, both the
speed of sound and the phase of the sound waves are affected by the
damping of the air viscosity. Herein, we propose a new finite-element
method (FEM) that considers the effects of the air viscosity. The
method was developed as an extension of existing FEMs for porous,
sound-absorbing materials. The results of a numerical calculation for a
three-dimensional ear-simulator model using the proposed FEM were
validated by comparing with theoretical lumped-parameter modeling
analysis and standard values.
Abstract: In this paper, we report the development of the device
for diagnostics of cardiovascular system state and associated
automated workstation for large-scale medical measurement data
collection and analysis. It was shown that optimal design for the
monitoring device is wristband as it represents engineering trade-off
between accuracy and usability. Monitoring device is based on the
infrared reflective photoplethysmographic sensor, which allows
collecting multiple physiological parameters, such as heart rate and
pulsing wave characteristics. Developed device uses BLE interface
for medical and supplementary data transmission to the coupled
mobile phone, which processes it and send it to the doctor's
automated workstation. Results of this experimental model
approbation confirmed the applicability of the proposed approach.
Abstract: An approach was evaluated for the retrieval of soil
moisture of bare soil surface using bistatic scatterometer data in the
angular range of 200 to 700 at VV- and HH- polarization. The
microwave data was acquired by specially designed X-band (10
GHz) bistatic scatterometer. The linear regression analysis was done
between scattering coefficients and soil moisture content to select the
suitable incidence angle for retrieval of soil moisture content. The 250
incidence angle was found more suitable. The support vector
regression analysis was used to approximate the function described
by the input output relationship between the scattering coefficient and
corresponding measured values of the soil moisture content. The
performance of support vector regression algorithm was evaluated by
comparing the observed and the estimated soil moisture content by
statistical performance indices %Bias, root mean squared error
(RMSE) and Nash-Sutcliffe Efficiency (NSE). The values of %Bias,
root mean squared error (RMSE) and Nash-Sutcliffe Efficiency
(NSE) were found 2.9451, 1.0986 and 0.9214 respectively at HHpolarization.
At VV- polarization, the values of %Bias, root mean
squared error (RMSE) and Nash-Sutcliffe Efficiency (NSE) were
found 3.6186, 0.9373 and 0.9428 respectively.
Abstract: A compact Ultra Wide Band (UWB) antenna with coplanar
waveguide feed has been designed and results are verified in
this paper. The antenna has been designed on FR4 substrate with
dielectric constant (εr) of 4.4 and dimensions of 32mm x 26mm x
0.8mm. The presented antenna shows return loss characteristics in the
band of 3.1 to 10.6 GHz as prescribed by FCC, USA. Parametric
studies have been done and results thus obtained have been
presented. Simulated results have been verified on Rohde & Swartz
VNA. The measured results are in good agreement with simulated
results which make the presented antenna suitable to be used for
wearable applications. Performance analysis of antenna has also been
shown in the presence of three layered Human Arm model. Results
obtained in presence of Human Arm model has been compared with
that in free space.
Abstract: In this communication, a low-cost circularly
polarized wire antenna exhibiting improved gain performance for
Dedicated Short Range Communications (DSRC), vehicle-to-vehicle
(V2V) and vehicle-to-infrastructure (V2I) communications is
presented. The proposed antenna comprises a Y-shaped quarterwavelength
monopole antenna surrounded by two iterations of eight
conductive arched walls acting as parasitic elements to enhance the
overall antenna gain and to shape the radiation pattern in the H-plane.
A hemispherical radome shell is added to protect the antenna
structure and its effect on the antenna performance is discussed. The
designed antenna demonstrates antenna gain of 8.2 dB with
omnidirectional far-field radiation pattern in the H-plane. The gain of
the proposed antenna is also compared with the characteristic of the
stand-alone Y-shaped monopole to highlight the advantages of the
proposed approach.
Abstract: Propagation of arbitrary amplitude nonlinear Alfven
waves has been investigated in low but finite β electron-positron-ion
plasma including full ion dynamics. Using Sagdeev pseudopotential
method an energy integral equation has been derived. The Sagdeev
potential has been calculated for different plasma parameters and it
has been shown that inclusion of ion parallel motion along the
magnetic field changes the nature of slow shear Alfven wave solitons
from dip type to hump type. The effects of positron concentration,
plasma-β and obliqueness of the wave propagation on the solitary
wave structure have also been examined.
Abstract: Chalcopyrite (CuFeS2) is the most common primary
mineral used for the commercial production of copper. The low
dissolution efficiency of chalcopyrite in sulfate media has prevented
an efficient industrial leaching of this mineral in sulfate media. Ferric
ions, bacteria, oxygen and other oxidants have been used as oxidizing
agents in the leaching of chalcopyrite in sulfate and chloride media
under atmospheric or pressure leaching conditions. Two leaching
methods were studied to evaluate chalcopyrite (CuFeS2) dissolution
in acid media. First, the conventional oxidative acid leaching method
was carried out using sulfuric acid (H2SO4) and potassium
dichromate (K2Cr2O7) as oxidant at atmospheric pressure. Second,
microwave-assisted acid leaching was performed using the
microwave accelerated reaction system (MARS) for same reaction
media. Parameters affecting the copper extraction such as leaching
time, leaching temperature, concentration of H2SO4 and
concentration of K2Cr2O7 were investigated. The results of
conventional acid leaching experiments were compared to the
microwave leaching method. It was found that the copper extraction
obtained under high temperature and high concentrations of oxidant
with microwave leaching is higher than those obtained
conventionally. 81% copper extraction was obtained by the
conventional oxidative acid leaching method in 180 min, with the
concentration of 0.3 mol/L K2Cr2O7 in 0.5M H2SO4 at 50 ºC, while
93.5% copper extraction was obtained in 60 min with microwave
leaching method under same conditions.
Abstract: Phonocardiography is important in appraisal of
congenital heart disease and pulmonary hypertension as it reflects the
duration of right ventricular systoles. The systolic murmur in patients
with intra-cardiac shunt decreases as pulmonary hypertension
develops and may eventually disappear completely as the pulmonary
pressure reaches systemic level. Phonocardiography and auscultation
are non-invasive, low-cost, and accurate methods to assess heart
disease. In this work an objective signal processing tool to extract
information from phonocardiography signal using Wavelet is
proposed to classify the murmur as normal or abnormal. Since the
feature vector is large, a Binary Particle Swarm Optimization (PSO)
with mutation for feature selection is proposed. The extracted
features improve the classification accuracy and were tested across
various classifiers including Naïve Bayes, kNN, C4.5, and SVM.
Abstract: Typical load-bearing biological materials like bone,
mineralized tendon and shell, are biocomposites made from both
organic (collagen) and inorganic (biomineral) materials. This
amazing class of materials with intrinsic internally designed
hierarchical structures show superior mechanical properties with
regard to their weak components from which they are formed.
Extensive investigations concentrating on static loading conditions
have been done to study the biological materials failure. However,
most of the damage and failure mechanisms in load-bearing
biological materials will occur whenever their structures are exposed
to dynamic loading conditions. The main question needed to be
answered here is: What is the relation between the layout and
architecture of the load-bearing biological materials and their
dynamic behavior? In this work, a staggered model has been
developed based on the structure of natural materials at nanoscale and
Finite Element Analysis (FEA) has been used to study the dynamic
behavior of the structure of load-bearing biological materials to
answer why the staggered arrangement has been selected by nature to
make the nanocomposite structure of most of the biological materials.
The results showed that the staggered structures will efficiently
attenuate the stress wave rather than the layered structure.
Furthermore, such staggered architecture is effectively in charge of
utilizing the capacity of the biostructure to resist both normal and
shear loads. In this work, the geometrical parameters of the model
like the thickness and aspect ratio of the mineral inclusions selected
from the typical range of the experimentally observed feature sizes
and layout dimensions of the biological materials such as bone and
mineralized tendon. Furthermore, the numerical results validated with
existing theoretical solutions. Findings of the present work emphasize
on the significant effects of dynamic behavior on the natural
evolution of load-bearing biological materials and can help scientists
to design bioinspired materials in the laboratories.
Abstract: Sound processing is one the subjects that newly
attracts a lot of researchers. It is efficient and usually less expensive
than other methods. In this paper the flow generated sound is used to
estimate the flow speed of free flows. Many sound samples are
gathered. After analyzing the data, a parameter named wave power is
chosen. For all samples the wave power is calculated and averaged
for each flow speed. A curve is fitted to the averaged data and a
correlation between the wave power and flow speed is found. Test
data are used to validate the method and errors for all test data were
under 10 percent. The speed of the flow can be estimated by
calculating the wave power of the flow generated sound and using the
proposed correlation.
Abstract: In this paper, we consider some integrable Heisenberg
Ferromagnet Equations with self-consistent potentials. We study
their Lax representations. In particular we derive their equivalent
counterparts in the form of nonlinear Schr¨odinger type equations.
We present the integrable reductions of the Heisenberg Ferromagnet
Equations with self-consistent potentials. These integrable Heisenberg
Ferromagnet Equations with self-consistent potentials describe
nonlinear waves in ferromagnets with some additional physical fields.
Abstract: DNA Barcode provides good sources of needed
information to classify living species. The classification problem has
to be supported with reliable methods and algorithms. To analyze
species regions or entire genomes, it becomes necessary to use the
similarity sequence methods. A large set of sequences can be
simultaneously compared using Multiple Sequence Alignment which
is known to be NP-complete. However, all the used methods are still
computationally very expensive and require significant computational
infrastructure. Our goal is to build predictive models that are highly
accurate and interpretable. In fact, our method permits to avoid the
complex problem of form and structure in different classes of
organisms. The empirical data and their classification performances
are compared with other methods. Evenly, in this study, we present
our system which is consisted of three phases. The first one, is called
transformation, is composed of three sub steps; Electron-Ion
Interaction Pseudopotential (EIIP) for the codification of DNA
Barcodes, Fourier Transform and Power Spectrum Signal Processing.
Moreover, the second phase step is an approximation; it is
empowered by the use of Multi Library Wavelet Neural Networks
(MLWNN). Finally, the third one, is called the classification of DNA
Barcodes, is realized by applying the algorithm of hierarchical
classification.
Abstract: EEG correlates of mathematical and trait anxiety level
were studied in 52 healthy Russian-speakers during execution of
error-recognition tasks with lexical, arithmetic and algebraic
conditions. Event-related spectral perturbations were used as a
measure of brain activity. The ERSP plots revealed alpha/beta
desynchronizations within a 500-3000 ms interval after task onset
and slow-wave synchronization within an interval of 150-350 ms.
Amplitudes of these intervals reflected the accuracy of error
recognition, and were differently associated with the three conditions.
The correlates of anxiety were found in theta (4-8 Hz) and beta2 (16-
20 Hz) frequency bands. In theta band the effects of mathematical
anxiety were stronger expressed in lexical, than in arithmetic and
algebraic condition. The mathematical anxiety effects in theta band
were associated with differences between anterior and posterior
cortical areas, whereas the effects of trait anxiety were associated
with inter-hemispherical differences. In beta1 and beta2 bands effects
of trait and mathematical anxiety were directed oppositely. The trait
anxiety was associated with increase of amplitude of
desynchronization, whereas the mathematical anxiety was associated
with decrease of this amplitude. The effect of mathematical anxiety
in beta2 band was insignificant for lexical condition but was the
strongest in algebraic condition. EEG correlates of anxiety in theta
band could be interpreted as indexes of task emotionality, whereas
the reaction in beta2 band is related to tension of intellectual
resources.
Abstract: This paper describes a novel sensor device, a pressure
pulse wave meter, which uses a bidirectional condenser microphone.
The microphone work as a microphone as well as a sensor with high
gain over a wide frequency range; they are also highly reliable and
economic. Currently aging is becoming a serious social issue in Japan causing
increased medical expenses in the country. Hence, it is important for
elderly citizens to check health condition at home, and to care the
health conditions through daily monitoring. Given this circumstances,
we developed a novel pressure pulse wave meter based on a
bidirectional condenser microphone: this device is used as a measuring
instrument of health conditions.
Abstract: In this study, the signal of brain electrical activities of
the sixteen students selected from the Department of Electrical and
Energy at Usak University have been recorded during a lecturer
performed happiness emotions for the first group and anger emotions
for the second group in different time while the groups were in the
classroom separately. The attention and meditation data extracted
from the recorded signals have been analyzed and evaluated toward
the teacher’s specific emotion states simultaneously. Attention levels
of students who are under influence of happiness emotions of the
lecturer have a positive trend and attention levels of students who are
under influence of anger emotions of the lecturer have a negative
trend. The meditation or mental relaxation levels of students who are
under influence of happiness emotions of the lecturer are 34.3%
higher comparing with the mental relaxation levels of students who
are under influence of anger emotions of the lecturer.
Abstract: Numerical studies have been carried out using a
validated two-dimensional standard k-omega turbulence model for
the design optimization of a thrust vector control system using shock
induced self-impinging supersonic secondary double jet. Parametric
analytical studies have been carried out at different secondary
injection locations to identifying the highest unsymmetrical
distribution of the main gas flow due to shock waves, which produces
a desirable side force more lucratively for vectoring. The results from
the parametric studies of the case on hand reveal that the shock
induced self-impinging supersonic secondary double jet is more
efficient in certain locations at the divergent region of a CD nozzle
than a case with supersonic single jet with same mass flow rate. We
observed that the best axial location of the self-impinging supersonic
secondary double jet nozzle with a given jet interaction angle, built-in
to a CD nozzle having area ratio 1.797, is 0.991 times the primary
nozzle throat diameter from the throat location. We also observed
that the flexible steering is possible after invoking ON/OFF facility to
the secondary nozzles for meeting the onboard mission requirements.
Through our case studies we concluded that the supersonic self-impinging
secondary double jet at predesigned jet interaction angle
and location can provide more flexible steering options facilitating
with 8.81% higher thrust vectoring efficiency than the conventional
supersonic single secondary jet without compromising the payload
capability of any supersonic aerospace vehicle.
Abstract: The rapid growth of multimedia technology demands
the secure and efficient access to information. This fast growing lose
the confidence of unauthorized duplication. Henceforth the protection
of multimedia content is becoming more important. Watermarking
solves the issue of unlawful copy of advanced data. In this paper,
blind video watermarking technique has been proposed. A luminance
layer of selected frames is interlaced into two even and odd rows of
an image, further it is deinterlaced and equalizes the coefficients of
the two shares. Color watermark is split into different blocks, and the
pieces of block are concealed in one of the share under the wavelet
transform. Stack the two images into a single image by introducing
interlaced even and odd rows in the two shares. Finally, chrominance
bands are concatenated with the watermarked luminance band. The
safeguard level of the secret information is high, and it is
undetectable. Results show that the quality of the video is not
changed also yields the better PSNR values.
Abstract: This paper presents the design and fabrication of a
novel piezoelectric actuator for a gas micro pump with check valve
having the advantages of miniature size, light weight and low power
consumption. The micro pump is designed to have eight major
components, namely a stainless steel upper cover layer, a piezoelectric
actuator, a stainless steel diaphragm, a PDMS chamber layer, two
stainless steel channel layers with two valve seats, a PDMS check
valve layer with two cantilever-type check valves and an acrylic
substrate. A prototype of the gas micro pump, with a size of 52 mm ×
50 mm × 5.0 mm, is fabricated by precise manufacturing. This device
is designed to pump gases with the capability of performing the
self-priming and bubble-tolerant work mode by maximizing the stroke
volume of the membrane as well as the compression ratio via
minimization of the dead volume of the micro pump chamber and
channel. By experiment apparatus setup, we can get the real-time
values of the flow rate of micro pump and the displacement of the
piezoelectric actuator, simultaneously. The gas micro pump obtained
higher output performance under the sinusoidal waveform of 250 Vpp.
The micro pump achieved the maximum pumping rates of 1185
ml/min and back pressure of 7.14 kPa at the corresponding frequency
of 120 and 50 Hz.
Abstract: Cemented carbides, owing to their excellent
mechanical properties, have been of immense interest in the field of
hard materials for the past few decades. A number of processing
techniques have been developed to obtain high quality carbide tools,
with a wide range of grain size depending on the application and
requirements. Microwave sintering is one of the heating processes,
which has been used to prepare a wide range of materials including
ceramics. A deep understanding of microwave sintering and its
contribution towards control of grain growth and on deformation of
the resulting carbide materials requires further studies and attention.
In addition, the effect of binder materials and their behavior during
microwave sintering is another area that requires clear understanding.
This review aims to focus on microwave sintering, providing
information of how the process works and what type of materials it is
best suited for. In addition, a closer look at some microwave sintered
Tungsten Carbide-Cobalt samples will be taken and discussed,
highlighting some of the key issues and challenges faced in this
research area.