Abstract: This paper investigates the characteristics of wall
pressure fluctuations in naturally developing boundary layer flows
on axisymmetric bodies experimentally. The axisymmetric body has
a modified ellipsoidal blunt nose. Flush-mounted microphones are
used to measure the wall pressure fluctuations in the boundary layer
flow over the body. The measurements are performed in a low noise
wind tunnel. It is found that the correlation between the flow regime
and the characteristics of the pressure fluctuations is distinct. The
process from small fluctuation in laminar flow to large fluctuation in
turbulent flow is investigated. Tollmien-Schlichting wave (T-S wave)
is found to generate and develop in transition. Because of the T-S
wave, the wall pressure fluctuations in the transition region are higher
than those in the turbulent boundary layer.
Abstract: The occurrences of precipitation, also commonly
referred as rain, in the form of "convective" and "stratiform" have
been identified to exist worldwide. In this study, the radar return
echoes or known as reflectivity values acquired from radar scans
have been exploited in the process of classifying the type of rain
endured. The investigation use radar data from Malaysian
Meteorology Department (MMD). It is possible to discriminate the
types of rain experienced in tropical region by observing the vertical
characteristics of the rain structure. .Heavy rain in tropical region
profoundly affects radiowave signals, causing transmission
interference and signal fading. Required wireless system fade margin
depends on the type of rain. Information relating to the two
mentioned types of rain is critical for the system engineers and
researchers in their endeavour to improve the reliability of
communication links. This paper highlights the quantification of
percentage occurrences over one year period in 2009.
Abstract: In this study, Brillouin Gain Spectrum (BGS) is
experimentally analyzed in the Brillouin Optical Time Domain
Reflectometry (BOTDR) and Brillouin Optical Time Domain
Analyzer (BOTDA). For this purpose, the signal level of the
microwave generator is varied and the effects of BGS are
investigated. In the setups, 20 km conventional single mode fiber is
used to both setups and laser wavelengths are selected around 1550
nm. To achieve best results, it can be used between 5 dBm to 15 dBm
signal level of microwave generator for BOTDA and BOTDR setups.
Abstract: A physical model for guiding the wave in
photorefractive media is studied. Propagation of cos-Gaussian beam
as the special cases of sinusoidal-Gaussian beams in photorefractive
crystal is simulated numerically by the Crank-Nicolson method in
one dimension. Results show that the beam profile deforms as the
energy transfers from the center to the tails under propagation. This
simulation approach is of significant interest for application in optical
telecommunication. The results are presented graphically and
discussed.
Abstract: Wavelength Division Multiplexing (WDM)
technology is the most promising technology for the proper
utilization of huge raw bandwidth provided by an optical fiber. One
of the key problems in implementing the all-optical WDM network is
the packet contention. This problem can be solved by several
different techniques. In time domain approach the packet contention
can be reduced by incorporating Fiber Delay Lines (FDLs) as optical
buffer in the switch architecture. Different types of buffering
architectures are reported in literatures. In the present paper a
comparative performance analysis of three most popular FDL
architectures are presented in order to obtain the best contention
resolution performance. The analysis is further extended to consider
the effect of different fiber non-linearities on the network
performance.
Abstract: A broadband wire monopole antenna loaded by inhomogeneous stack of annular dielectric ring resonators (DRRs) is proposed. The proposed antenna exhibits a broad impedance bandwidth from 3 to 30 GHz. This is achieved by adding an external step matching network at the antenna feed point. The matching network is comprised of three annular DRRs possessing different permittivity values and sharing the same axial over a finite ground plane. The antenna performance is characterized using full-wave EM simulation. Compared to previous-reported wire antennas with improved bandwidth achieved by DRRs, the proposed topology provides relatively compact realization and superior broadband performance.
Abstract: In the present study, feasibility of the selective surface
hydrophilization of polyvinyl chloride (PVC) by microwave treatment
was evaluated to facilitate the separation from automotive shredder
residue (ASR), by the froth flotation. The combination of 60 sec
microwave treatment with PAC, a sharp and significant decrease about
16.5° contact angle of PVC was observed in ASR plastic compared
with other plastics. The microwave treatment with the addition of PAC
resulted in a synergetic effect for the froth flotation, which may be a
result of the 90% selective separation of PVC from ASR plastics, with
82% purity. While, simple mixing with a nanometallic Ca/CaO/PO4
dispersion mixture immobilized 95-100% of heavy metals in ASR
soil/residues. The quantity of heavy metals leached from thermal
residues after treatment by nanometallic Ca/CaO/PO4 was lower than
the Korean standard regulatory limit for hazardous waste landfills.
Microwave treatment can be a simple and effective method for PVC
separation from ASR plastics.
Abstract: In this paper, de Laval rotor system has been
characterized by a hinge model and its transient response numerically
treated for a dynamic solution. The effect of the ensuing non-linear
disturbances namely rub and breathing crack is numerically
simulated. Subsequently, three analysis methods: Orbit Analysis, Fast
Fourier Transform (FFT), and Wavelet Transform (WT) are
employed to extract features of the vibration signal of the faulty
system. An analysis of the system response orbits clearly indicates
the perturbations due to the rotor-to-stator contact. The sensitivities
of WT to the variation in system speed have been investigated by
Continuous Wavelet Transform (CWT). The analysis reveals that
features of crack, rubs and unbalance in vibration response can be
useful for condition monitoring. WT reveals its ability to detect nonlinear
signal, and obtained results provide a useful tool method for
detecting machinery faults.
Abstract: In this paper, approach to incoherent signal detection
in multi-element antenna array are researched and modeled. Two
types of useful signals with unknown wavefront were considered:
first one, deterministic (Barker code), and second one, random
(Gaussian distribution). The derivation of the sufficient statistics took
into account the linearity of the antenna array. The performance
characteristics and detecting curves are modeled and compared for
different useful signals parameters and for different number of
elements of the antenna array. Results of researches in case of some
additional conditions can be applied to a digital communications
systems.
Abstract: Thermoacoustic refrigerator is a cooling device which
uses the acoustic waves to produce the cooling effect. The aim of this
paper is to explore the experimental and numerical feasibility of a
standing-wave thermoacoustic refrigerator. The effects of the stack
length, position of stack and operating frequency on the cooling
performance are carried out. The circular pore stacks are tested under
the atmospheric pressure. A low-cost loudspeaker is used as an
acoustic driver. The results show that the location of stack installed in
resonator tube has a greater effect on the cooling performance, than
the stack length and operating frequency, respectively. The
temperature difference across the ends of stack can be generated up
to 13.7°C, and the temperature of cold-end is dropped down by 5.3°C
from the ambient temperature.
Abstract: Geological and tectonic framework indicates that
Bangladesh is one of the most seismically active regions in the world.
The Bengal Basin is at the junction of three major interacting plates:
the Indian, Eurasian, and Burma Plates. Besides there are many
active faults within the region, e.g. the large Dauki fault in the north.
The country has experienced a number of destructive earthquakes due
to the movement of these active faults. Current seismic provisions of
Bangladesh are mostly based on earthquake data prior to the 1990.
Given the record of earthquakes post 1990, there is a need to revisit
the design provisions of the code. This paper compares the base shear
demand of three major cities in Bangladesh: Dhaka (the capital city),
Sylhet, and Chittagong for earthquake scenarios of magnitudes
7.0MW, 7.5MW, 8.0MW, and 8.5MW using a stochastic model. In
particular, the stochastic model allows the flexibility to input region
specific parameters such as shear wave velocity profile (that were
developed from Global Crustal Model CRUST2.0) and include the
effects of attenuation as individual components. Effects of soil
amplification were analysed using the Extended Component
Attenuation Model (ECAM). Results show that the estimated base
shear demand is higher in comparison with code provisions leading to
the suggestion of additional seismic design consideration in the study
regions.
Abstract: Wireless networks are built upon the open shared
medium which makes easy for attackers to conduct malicious
activities. Jamming is one of the most serious security threats to
information economy and it must be dealt efficiently. Jammer
prevents legitimate data to reach the receiver side and also it
seriously degrades the network performance. The objective of this
paper is to provide a general overview of jamming in wireless
network. It covers relevant works, different jamming techniques,
various types of jammers and typical prevention techniques.
Challenges associated with comparing several anti-jamming
techniques are also highlighted.
Abstract: The understanding of geotechnical characteristics of
near-surface material and the effects of the groundwater is very
important problem in such as site studies. For showing the relations
between seismic data and groundwater, we selected about 25 km2 as
the study area. It has been presented which is a detailed work of
seismic data and groundwater depths of Gokpinar Damp area.
Seismic waves velocity (Vp and Vs) are very important parameters
showing the soil properties. The seismic records were used the
method of the multichannel analysis of surface waves near area of
Gokpinar Damp area. Sixty sites in this area have been investigated
with survey lines about 60 m in length. MASW (Multichannel
analysis of surface wave) method has been used to generate onedimensional
shear wave velocity profile at locations. These shear
wave velocities are used to estimate equivalent shear wave velocity in
the study area at every 2 and 5 m intervals up to a depth of 45 m.
Levels of equivalent shear wave velocity of soil are used the
classified of the study area. After the results of the study, it must be
considered as components of urban planning and building design of
Gokpinar Damp area, Denizli and the application and use of these
results should be required and enforced by municipal authorities.
Abstract: Monitoring the conditions of rotating machinery, such
as bearings, is important in order to improve the stability of work.
Acoustic Emission (AE) and vibration analysis are some of the most
accomplished techniques used for this purpose. Acoustic emission
has the ability to detect the initial phase of component degradation.
Moreover, it has been observed that vibration analysis is not as
successful at low rotational speeds (below 100 rpm). This because the
energy generated within this speed region is not detectable using
conventional vibration. From this perspective, this paper has
presented a brief review of using acoustic emission techniques for
monitoring bearing conditions.
Abstract: In this paper, we calculate the two-photon ionization
(TPI) cross-section for pump-probe scheme in Ag neutral cluster. The
pump photon energy is assumed to be close to the surface plasmon
(SP) energy of cluster in dielectric media. Due to this choice, the
pump wave excites collective oscillations of electrons-SP and the
probe wave causes ionization of the cluster. Since the interband
transition energy in Ag exceeds the SP resonance energy, the main
contribution into the TPI comes from the latter. The advantage of Ag
clusters as compared to the other noble metals is that the SP
resonance in silver cluster is much sharper because of peculiarities of
its dielectric function. The calculations are performed by separating
the coordinates of electrons corresponding to the collective
oscillations and the individual motion that allows taking into account
the resonance contribution of excited SP oscillations. It is shown that
the ionization cross section increases by two orders of magnitude if
the energy of the pump photon matches the surface plasmon energy
in the cluster.
Abstract: Anaerobic digestion is a well-known technique for
sustainable energy recovery from sewage sludge. However, sewage
sludge digestion is restricted due to certain factors. Pre-treatment
methods have been established in various publications as a promising
technique to improve the digestibility of the sewage sludge and to
enhance the biogas generated which can be used for energy recovery.
In this study, continuous flow microwave (MW) pre-treatment with
different intensities were compared by using 5 L semi-continuous
digesters at a hydraulic retention time of 27 days. We focused on the
effects of MW at different intensities on the sludge solubilization,
sludge digestibility, and biogas production of the untreated and MW
pre-treated sludge. The MW pre-treatment demonstrated an increase
in the ratio of soluble chemical oxygen demand to total chemical
oxygen demand (sCOD/tCOD) and volatile fatty acid (VFA)
concentration. Besides that, the total volatile solid (TVS) removal
efficiency and tCOD removal efficiency also increased during the
digestion of the MW pre-treated sewage sludge compared to the
untreated sewage sludge. Furthermore, the biogas yield also
subsequently increases due to the pre-treatment effect. A higher MW
power level and irradiation time generally enhanced the biogas
generation which has potential for sustainable energy recovery from
sewage treatment plant. However, the net energy balance tabulation
shows that the MW pre-treatment leads to negative net energy production.
Abstract: The analytical bright two soliton solution of the 3-
coupled nonlinear Schrödinger equations with variable coefficients in
birefringent optical fiber is obtained by Darboux transformation
method. To the design of ultra-speed optical devices, Soliton
interaction and control in birefringence fiber is investigated. Lax pair
is constructed for N coupled NLS system through AKNS method.
Using two-soliton solution, we demonstrate different interaction
behaviors of solitons in birefringent fiber depending on the choice of
control parameters. Our results shows that interactions of optical
solitons have some specific applications such as construction of logic
gates, optical computing, soliton switching, and soliton amplification
in wavelength division multiplexing (WDM) system.
Abstract: The effects of the contact ball-lens on the soda lime
glass in laser thermal cleavage with a cw Nd-YAG laser were
investigated in this study. A contact ball-lens was adopted to generate
a bending force on the crack formation of the soda-lime glass in the
laser cutting process. The Nd-YAG laser beam (wavelength of 1064
nm) was focused through the ball-lens and transmitted to the soda-lime
glass, which was coated with a carbon film on the surface with a
bending force from a ball-lens to generate a tensile stress state on the
surface cracking. The fracture was controlled by the contact ball-lens
and a straight cutting was tested to demonstrate the feasibility.
Experimental observations on the crack propagation from the leading
edge, main section and trailing edge of the glass sheet were compared
with various mechanical and thermal loadings. Further analyses on the
stress under various laser powers and contact ball loadings were made
to characterize the innovative technology. The results show that the distributions of the side crack at the
leading and trailing edges are mainly dependent on the boundary
condition, contact force, cutting speed and laser power. With the
increase of the mechanical and thermal loadings, the region of the side
cracks might be dramatically reduced with proper selection of the
geometrical constrains. Therefore the application of the contact
ball-lens is a possible way to control the fracture in laser cleavage with
improved cutting qualities.
Abstract: The laser-ultrasonic method is realized for
quantifying the influence of porosity on the local Young’s
modulus of isotropic composite materials. The method is based on
a laser thermooptical method of ultrasound generation combined
with measurement of the phase velocity of longitudinal and shear
acoustic waves in samples. The main advantage of this method
compared with traditional ultrasonic research methods is the
efficient generation of short and powerful probing acoustic pulses
required for reliable testing of ultrasound absorbing and
scattering heterogeneous materials. Using as an example samples
of a metal matrix composite with reinforcing microparticles of
silicon carbide in various concentrations, it is shown that to
provide an effective increase in Young’s modulus with increasing
concentration of microparticles, the porosity of the final sample
should not exceed 2%.
Abstract: Recent investigations have demonstrated the global
sea level rise due to climate change impacts. In this study, climate
changes study the effects of increasing water level in the strait of
Hormuz. The probable changes of sea level rise should be
investigated to employ the adaption strategies. The climatic output
data of a GCM (General Circulation Model) named CGCM3 under
climate change scenario of A1b and A2 were used. Among different
variables simulated by this model, those of maximum correlation
with sea level changes in the study region and least redundancy
among themselves were selected for sea level rise prediction by using
stepwise regression. One of models (Discrete Wavelet artificial
Neural Network) was developed to explore the relationship between
climatic variables and sea level changes. In these models, wavelet
was used to disaggregate the time series of input and output data into
different components and then ANN was used to relate the
disaggregated components of predictors and input parameters to each
other. The results showed in the Shahid Rajae Station for scenario
A1B sea level rise is among 64 to 75 cm and for the A2 Scenario sea
level rise is among 90 t0 105 cm. Furthermore, the result showed a
significant increase of sea level at the study region under climate
change impacts, which should be incorporated in coastal areas
management.