Abstract: This paper reports the results of an experimental study
conducted to characterise the gas-liquid multiphase flows
experienced within a vertical riser transporting a range of gas-liquid
flow rates. The scale experiments were performed using an
air/silicone oil mixture within a 6 m long riser. The superficial air
velocities studied ranged from 0.047 to 2.836 m/ s, whilst
maintaining a liquid superficial velocity at 0.047 m/ s. Measurements
of the mean cross-sectional and time average radial void fraction
were obtained using a wire mesh sensor (WMS). The data were
recorded at an acquisition frequency of 1000 Hz over an interval of
60 seconds. For the range of flow conditions studied, the average
void fraction was observed to vary between 0.1 and 0.9. An analysis
of the data collected concluded that the observed void fraction was
strongly affected by the superficial gas velocity, whereby the higher
the superficial gas velocity, the higher was the observed average void
fraction. The average void fraction distributions observed were in
good agreement with the results obtained by other researchers. When
the air-silicone oil flows were fully developed reasonably symmetric
profiles were observed, with the shape of the symmetry profile being
strongly dependent on the superficial gas velocity.
Abstract: People from different cultures favor web pages
characterized by the values of their culture and, therefore, tend to
prefer different characteristics of a website according to their cultural
values in terms of navigation, security, product information, customer
service, shopping and design tools. For a company aiming to
globalize its market it is useful to implement country specific cultural
interfaces and different web sites for countries with different cultures.
This paper, following the conclusions proposed by two models of
Hall and Hofstede, and the studies of Marcus and Gould, defines,
through an empirical analysis, the guidelines of web design for both
the Scandinavian countries and Malaysia.
Abstract: Data compression is used operationally to reduce bandwidth and storage requirements. An efficient method for achieving lossless weather radar data compression is presented. The characteristics of the data are taken into account and the optical linear prediction is used for the PPI images in the weather radar data in the proposed method. The next PPI image is identical to the current one and a dramatic reduction in source entropy is achieved by using the prediction algorithm. Some lossless compression methods are used to compress the predicted data. Experimental results show that for the weather radar data, the method proposed in this paper outperforms the other methods.
Abstract: The aim of this work is to study the possible use of
stone cutting sludge waste in concrete production, which would
reduce both the environmental impact and the production cost .Slurry
sludge was used a source of water in concrete production, which was
obtained from Samara factory/Jordan, The physico-chemical and
mineralogical characterization of the sludge was carried out to
identify the major components and to compare it with the typical
sand used to produce concrete. Samples analysis showed that 96% of
slurry sludge volume is water, so it should be considered as an
important source of water. Results indicated that the use of slurry
sludge as water source in concrete production has insignificant effect
on compression strength, while it has a sharp effect on the slump
values. Using slurry sludge with a percentage of 25% of the total
water content obtained successful concrete samples regarding slump
and compression tests. To clarify slurry sludge, settling process can
be used to remove the suspended solid. A settling period of 30 min.
obtained 99% removal efficiency. The clarified water is suitable for
using in concrete mixes, which reduce water consumption, conserve
water recourses, increase the profit, reduce operation cost and save
the environment. Additionally, the dry sludge could be used in the
mix design instead of the fine materials with sizes < 160 um. This
application could conserve the natural materials and solve the
environmental and economical problem caused by sludge
accumulation.
Abstract: REY area has been located in Tehran Province and several archaeological ruins of this area indicate that the settlement in this area has been started since several thousand years ago. In this paper, the main investigation items consist of analysis of oil components and groundwater quality inside the wells. By finding the contents of oil in the well, it is possible to find out the pollution source by comparing the oil contents of well with other oil products that are used inside and outside of the oil farm. Investigation items consist of analysis of BTEX (Benzene, Toluene, Ethyl-benzene, Xylene), Gas chromatographic distillation characteristics, Water content, Density, Sulfur content, Lead content, Atmospheric distillation, MTBE(Methyl tertiary butyl ether). Analysis of polluting oil components showed that except MW(Monitoring Well)10 and MW 15 that oil with slightly heavy components was detected in them; with a high possibility the polluting oil is light oil.
Abstract: A design of communication area for infrared
electronic-toll-collection systems to provide an extended
communication interval in the vehicle traveling direction and
regular boundary between contiguous traffic lanes is proposed.
By utilizing two typical low-cost commercial infrared LEDs with
different half-intensity angles Φ1/2 = 22◦ and 10◦, the radiation
pattern of the emitter is designed to properly adjust the spatial
distribution of the signal power. The aforementioned purpose
can be achieved with an LED array in a three-piece structure
with appropriate mounting angles. With this emitter, the influence
of the mounting parameters, including the mounting height and
mounting angles of the on-board unit and road-side unit, on the
system performance in terms of the received signal strength and
communication area are investigated. The results reveal that, for
our emitter proposed in this paper, the ideal ”long-and-narrow”
characteristic of the communication area is very little affected by
these mounting parameters. An optimum mounting configuration is
also suggested.
Abstract: Composites based on a biodegradable polycaprolactone (PCL) containing 0.5, 1.0 and 2.0 wt % of titanium dioxide (TiO2) micro and nanoparticles were prepared by melt mixing and the effect of filler type and contents on the thermal properties, dynamic-mechanical behaviour and morphology were investigated. Measurements of storage modulus and loss modulus by dynamic mechanical analysis (DMA) showed better results for microfilled PCL/TiO2 composites than nanofilled composites, with the same filler content. DSC analysis showed that the Tg and Tc of micro and nanocomposites were slightly lower than those of neat PCL. The crystallinity of the PCL increased with the addition of TiO2 micro and nanoparticles; however, the cc for the PCL was unchanged with micro TiO2 content. The thermal stability of PCL/TiO2 composites were characterized using thermogravimetric analysis (TGA). The initial weight loss (5 wt %) occurs at slightly higher temperature with micro and nano TiO2 addition and with increasing TiO2 content.
Abstract: The paper provides the basic overview of simulation optimization. The procedure of its practical using is demonstrated on the real example in simulator Witness. The simulation optimization is presented as a good tool for solving many problems in real praxis especially in production systems. The authors also characterize their own experiences and they mention the strengths and weakness of simulation optimization.
Abstract: A two-dimensional numerical simulation of the contribution
of both inertial and aerodynamic forces on the blade loads of
a Vertical-Axis Wind Turbine (VAWT) is presented. After describing
the computational model and the relative validation procedure, a
complete campaign of simulations - based on full RANS unsteady
calculations - is proposed for a three-bladed rotor architecture characterized
by a NACA 0021 airfoil. For each analyzed angular velocity,
the combined effect of pressure and viscous forces acting on every
rotor blade are compared to the corresponding centrifugal forces,
due to the revolution of the turbine, thus achieving a preliminary
estimation of the correlation between overall rotor efficiency and
structural blade loads.
Abstract: In-vitro mouse co-culture of E14 embryonic stem cells
(ESCs) and OP9 stromal cells can recapitulate the earliest stages of
haematopoietic development, not accessible in human embryos,
supporting both haemogenic precursors and their primitive
haematopoietic progeny. 1α, 25-Dihydroxy-vitamin D3 (VD3) has
been demonstrated to be a powerful differentiation inducer for a wide
variety of neoplastic cells, and could enhance early differentiation of
ESCs into blood cells in E14/OP9 co-culture. This study aims to
ascertain whether VD3 is key in promoting differentiation and
suppressing proliferation, by separately investigating the effects of
VD3 on the proliferation phase of the E14 cell line and on stromal
OP9 cells.The results showed that VD3 inhibited the proliferation of
the cells in a dose-dependent manner, quantitatively by decreased cell
number, and qualitatively by alkaline-phosphatase staining that
revealed significant differences between VD3-treated and untreated
cells, characterised by decreased enzyme expression (colourless
cells). Propidium-iodide cell-cycle analyses showed no significant
percentage change in VD3-treated E14 and OP9 cells within their G
and S-phases, compared to the untreated controls, despite the
increased percentage of G-phase compared to the S-phase in a dosedependent
manner. These results with E14 and OP9 cells indicate that
adequate VD3 concentration enhances cellular differentiation and
inhibits proliferation. The results also suggest that if E14 and OP9
cells were co-cultured andVD3-treated, there would be furtherenhanced
differentiation of ESCs into blood cells.
Abstract: A generalized Digital Modulation Identification algorithm for adaptive demodulator has been developed and presented in this paper. The algorithm developed is verified using wavelet Transform and histogram computation to identify QPSK and QAM with GMSK and M–ary FSK modulations. It has been found that the histogram peaks simplifies the procedure for identification. The simulated results show that the correct modulation identification is possible to a lower bound of 5 dB and 12 dB for GMSK and QPSK respectively. When SNR is above 5 dB the throughput of the proposed algorithm is more than 97.8%. The receiver operating characteristics (ROC) has been computed to measure the performance of the proposed algorithm and the analysis shows that the probability of detection (Pd) drops rapidly when SNR is 5 dB and probability of false alarm (Pf) is smaller than 0.3. The performance of the proposed algorithm has been compared with existing methods and found it will identify all digital modulation schemes with low SNR.
Abstract: Characterized as rich mineral substances, low
temperature, few bacteria, and stability with numerous implementation
aspects on aquaculture, food, drinking, and leisure, the deep sea water
(DSW) development has become a new industry in the world. It has
been report that marine algae contain various biologically active
compounds. This research focued on the affections in cultivating
Sagrassum cristaefolium with different concentration of deep sea
water(DSW) and surface sea water(SSW). After two and four weeks,
the total phenolic contents were compared in Sagrassum cristaefolium
culturing with different ways, and the reductive activity of them was
also be tried with potassium ferricyanide. Those fresh seaweeds were
dried with oven and were ground to powder. Progressively, the marine
algae we cultured was extracted by water under the condition with
heating them at 90Ôäâ for 1hr.The total phenolic contents were be
executed using Folin–Ciocalteu method. The results were explaining
as follows: the highest total phenolic contents and the best reductive
ability of all could be observed on the 1/4 proportion of DSW to SSW
culturing in two weeks. Furthermore, the 1/2 proportion of DSW to
SSW also showed good reductive ability and plentiful phenolic
compositions. Finally, we confirmed that difference proportion of
DSW and SSW is the major point relating to ether the total phenolic
components or the reductive ability in the Sagrassum cristaefolium. In
the future, we will use this way to mass production the marine algae or
other micro algae on industry applications.
Abstract: Most paddy rice fields in East Asia are small parcels,
and the weather conditions during the growing season are usually
cloudy. FORMOSAT-2 multi-spectral images have an 8-meter
resolution and one-day recurrence, ideal for mapping paddy rice fields
in East Asia. To map rice fields, this study first determined the
transplanting and the most active tillering stages of paddy rice and
then used multi-temporal images to distinguish different growing
characteristics between paddy rice and other ground covers. The
unsupervised ISODATA (iterative self-organizing data analysis
techniques) and supervised maximum likelihood were both used to
discriminate paddy rice fields, with training areas automatically
derived from ten-year cultivation parcels in Taiwan. Besides original
bands in multi-spectral images, we also generated normalized
difference vegetation index and experimented with object-based
pre-classification and post-classification. This paper discusses results
of different image classification methods in an attempt to find a
precise and automatic solution to mapping paddy rice in Taiwan.
Abstract: The production of activated carbon from low or zero cost of agricultural by-products or wastes has received great attention from academics and practitioners due to its economic and environmental benefits. In the production of bamboo furniture, a significant amount of bamboo waste is inevitably generated. Therefore, this research aimed to prepare activated carbons from bamboo furniture waste by chemical (KOH) activation and determine their properties and adsorption capacities for water treatment. The influence of carbonization time on the properties and adsorption capacities of activated carbons was also investigated. The finding showed that the bamboo-derived activated carbons had microporous characteristics. They exhibited high tendency for the reduction of impurities present in effluent water. Their adsorption capacities were comparable to the adsorption capacity of a commercial activated carbon regarding to the reduction in COD, TDS and turbidity of the effluent water.
Abstract: Purpose of this work is to develop an automatic classification system that could be useful for radiologists in the breast cancer investigation. The software has been designed in the framework of the MAGIC-5 collaboration. In an automatic classification system the suspicious regions with high probability to include a lesion are extracted from the image as regions of interest (ROIs). Each ROI is characterized by some features based generally on morphological lesion differences. A study in the space features representation is made and some classifiers are tested to distinguish the pathological regions from the healthy ones. The results provided in terms of sensitivity and specificity will be presented through the ROC (Receiver Operating Characteristic) curves. In particular the best performances are obtained with the Neural Networks in comparison with the K-Nearest Neighbours and the Support Vector Machine: The Radial Basis Function supply the best results with 0.89 ± 0.01 of area under ROC curve but similar results are obtained with the Probabilistic Neural Network and a Multi Layer Perceptron.
Abstract: Traffic density, an indicator of traffic
conditions, is one of the most critical characteristics to
Intelligent Transport Systems (ITS). This paper investigates
recursive traffic density estimation using the information
provided from inductive loop detectors. On the basis of the
phenomenological relationship between speed and density, the
existing studies incorporate a state space model and update the
density estimate using vehicular speed observations via the
extended Kalman filter, where an approximation is made
because of the linearization of the nonlinear observation
equation. In practice, this may lead to substantial estimation
errors. This paper incorporates a suitable transformation to
deal with the nonlinear observation equation so that the
approximation is avoided when using Kalman filter to
estimate the traffic density. A numerical study is conducted. It
is shown that the developed method outperforms the existing
methods for traffic density estimation.
Abstract: The purpose of this study was to investigate the
response of the newly released Gafchromic HD-V2 film for alpha
particle of 5.5 MeV. Gafchromic HD-V2 was exposed to alpha
particles of energy 5 MeV from 241Am for different durations. Then
the films were scanned with a flatbed scanner. The dose response
curve up to 2200 Gy has been achieved. The film’s reproducibility
and sensitivity were evaluated. The results obtained show that the net
optical density increases almost exponentially with the increase in the
exposure time, and it becomes saturated after prolonged exposure
times. The red channel shows the highest sensitivity, with a value of
4 x 10-3 Gy-1 at netOD of 0.4. The inter-film reproducibility was
measured and the relative uncertainty found was 1.7 %, 2.1 % and 2.3
% for grey, red and green channels, respectively.
Abstract: This paper presents a review on published literature
and experimental works on local sands for possible use as proppant,
specifically those from Terengganu coastal area. This includes
examination on characteristics of sand samples and selection of
experiments for proppant testing. Sand samples from identified areas
were tested according to particle size distribution, density, roundness
and sphericity, turbidity and mineralogy. Results from sand samples
were compared against proppant specifications set by API RP 56 and
selected commercial proppants. The present study found that the size
distribution, sphericity, turbidity and bulk density of Terengganu
sands are at par with some of commercial proppants. Nevertheless,
Terengganu sand samples do not completely surpass the required
roundness for use as proppant.
Abstract: The curves, of which the square of the distance
between the two points equal to zero, are called minimal or isotropic
curves [4]. In this work, first, necessary and sufficient conditions to
be a Pseudo Helix, which is a special case of such curves, are
presented. Thereafter, it is proven that an isotropic curve-s position
vector and pseudo curvature satisfy a vector differential equation of
fourth order. Additionally, In view of solution of mentioned
equation, position vector of pseudo helices is obtained.
Abstract: A new supported liquid membrane (SLM) system for
the selective transport of VO2
+ ions was prepared in this present
work. The SLM was a thin porous polyvinylidene difluoride
(PVDF) membrane soaked with Di-(2-ethylhexyl) phosphoric acid
(D2EHPA) as mobile carrier in Xylene as organic solvent.
D2EHPA acts as a highly selective carrier for the uphill transport of
VO2
+ ions through the SLM. The transport of VO2
+ ions reached to
64%. In the presence of P2O7-2 ion as suitable masking agent in the
feed solution, the interfering effects of other cations were eliminated.