Abstract: The three-time-scale plant model of a wind power
generator, including a wind turbine, a flexible vertical shaft, a Variable
Inertia Flywheel (VIF) module, an Active Magnetic Bearing (AMB)
unit and the applied wind sequence, is constructed. In order to make
the wind power generator be still able to operate as the spindle speed
exceeds its rated speed, the VIF is equipped so that the spindle speed
can be appropriately slowed down once any stronger wind field is
exerted. To prevent any potential damage due to collision by shaft
against conventional bearings, the AMB unit is proposed to regulate
the shaft position deviation. By singular perturbation order-reduction
technique, a lower-order plant model can be established for the
synthesis of feedback controller. Two major system parameter
uncertainties, an additive uncertainty and a multiplicative uncertainty,
are constituted by the wind turbine and the VIF respectively.
Frequency Shaping Sliding Mode Control (FSSMC) loop is proposed
to account for these uncertainties and suppress the unmodeled
higher-order plant dynamics. At last, the efficacy of the FSSMC is
verified by intensive computer and experimental simulations for
regulation on position deviation of the shaft and counter-balance of
unpredictable wind disturbance.
Abstract: A series of tests on cold-formed steel (CFS) wall plate system subjected to uplift force at the mid span of the wall plate is presented. The aim of the study was to study the behaviour and identify the modes of failure of CFS wall plate system. Two parameters were considered in these studies: 1) different dimension of U-bracket at the supports and 2) different sizes of lipped C-channel. The lipped C-channels used were C07508, C07512 and C10012. The dimensions of the leg of U-bracket were 50x35 mm and 50x60 mm respectively, where 25 mm clearance was provided to the connections for specimens with clearance. Results show that specimens with and without clearance experienced the same mode of failure. Failure began with the yielding of the connectors followed by distortional buckling of the wall plate. However, when C075 sections were used as wall plate, the system behaved differently. There was a large deformation in the wall plate and failure began in the distortional buckling of the wall plate followed by bearing of the connecting plates at the supports (U-bracket). The ultimate strength of the system also decreased dramatically when C075 sections were used.
Abstract: Single-pole switching scheme is widely used in the
Extra High Voltage system. However, the substantial negativesequence
current injected to the turbine-generators imposes the
electromagnetic (E/M) torque of double system- frequency
components during the dead time (between single-pole clearing and
line reclosing). This would induce supersynchronous resonance
(SPSR) torque amplifications on low pressure turbine generator
blades and even lead to fatigue damage. This paper proposes the
design of a mechanical filter (MF) with natural frequency close to
double-system frequency. From the simulation results, it is found that
such a filter not only successfully damps the resonant effect, but also
has the characteristics of feasibility and compact.
Abstract: This study presents a systematic analysis of the
dynamic behaviors of a gear-bearing system with porous squeeze film
damper (PSFD) under nonlinear suspension, nonlinear oil-film force
and nonlinear gear meshing force effect. It can be found that the
system exhibits very rich forms of sub-harmonic and even the chaotic
vibrations. The bifurcation diagrams also reveal that greater values of
permeability may not only improve non-periodic motions effectively,
but also suppress dynamic amplitudes of the system. Therefore, porous
effect plays an important role to improve dynamic stability of
gear-bearing systems or other mechanical systems. The results
presented in this study provide some useful insights into the design
and development of a gear-bearing system for rotating machinery that
operates in highly rotational speed and highly nonlinear regimes.
Abstract: According to the statistics, the prevalence of congenital hearing loss in Taiwan is approximately six thousandths; furthermore, one thousandths of infants have severe hearing impairment. Hearing ability during infancy has significant impact in the development of children-s oral expressions, language maturity, cognitive performance, education ability and social behaviors in the future. Although most children born with hearing impairment have sensorineural hearing loss, almost every child more or less still retains some residual hearing. If provided with a hearing aid or cochlear implant (a bionic ear) timely in addition to hearing speech training, even severely hearing-impaired children can still learn to talk. On the other hand, those who failed to be diagnosed and thus unable to begin hearing and speech rehabilitations on a timely manner might lose an important opportunity to live a complete and healthy life. Eventually, the lack of hearing and speaking ability will affect the development of both mental and physical functions, intelligence, and social adaptability. Not only will this problem result in an irreparable regret to the hearing-impaired child for the life time, but also create a heavy burden for the family and society. Therefore, it is necessary to establish a set of computer-assisted predictive model that can accurately detect and help diagnose newborn hearing loss so that early interventions can be provided timely to eliminate waste of medical resources. This study uses information from the neonatal database of the case hospital as the subjects, adopting two different analysis methods of using support vector machine (SVM) for model predictions and using logistic regression to conduct factor screening prior to model predictions in SVM to examine the results. The results indicate that prediction accuracy is as high as 96.43% when the factors are screened and selected through logistic regression. Hence, the model constructed in this study will have real help in clinical diagnosis for the physicians and actually beneficial to the early interventions of newborn hearing impairment.
Abstract: In quality control of freeze-dried durian, crispiness is
a key quality index of the product. Generally, crispy testing has to be
done by a destructive method. A nondestructive testing of the
crispiness is required because the samples can be reused for other
kinds of testing. This paper proposed a crispiness classification
method of freeze-dried durians using fuzzy logic for decision
making. The physical changes of a freeze-dried durian include the
pores appearing in the images. Three physical features including (1)
the diameters of pores, (2) the ratio of the pore area and the
remaining area, and (3) the distribution of the pores are considered to
contribute to the crispiness. The fuzzy logic is applied for making the
decision. The experimental results comparing with food expert
opinion showed that the accuracy of the proposed classification
method is 83.33 percent.
Abstract: There are lots of different ways to find the natural
frequencies of a rotating system. One of the most effective methods
which is used because of its precision and correctness is the
application of the transfer matrix. By use of this method the entire
continuous system is subdivided and the corresponding differential
equation can be stated in matrix form. So to analyze shaft that is this
paper issue the rotor is divided as several elements along the shaft
which each one has its own mass and moment of inertia, which this
work would create possibility of defining the named matrix. By
Choosing more elements number, the size of matrix would become
larger and as a result more accurate answers would be earned. In this
paper the dynamics of a rotor-bearing system is analyzed,
considering the gyroscopic effect. To increase the accuracy of
modeling the thickness of the disk and bearings is also taken into
account which would cause more complicated matrix to be solved.
Entering these parameters to our modeling would change the results
completely that these differences are shown in the results. As said
upper, to define transfer matrix to reach the natural frequencies of
probed system, introducing some elements would be one of the
requirements. For the boundary condition of these elements, bearings
at the end of the shaft are modeled as equivalent spring and dampers
for the discretized system. Also, continuous model is used for the
shaft in the system. By above considerations and using transfer
matrix, exact results are taken from the calculations. Results Show
that, by increasing thickness of the bearing the amplitude of vibration
would decrease, but obviously the stiffness of the shaft and the
natural frequencies of the system would accompany growth.
Consequently it is easily understood that ignoring the influences of
bearing and disk thicknesses would results not real answers.
Abstract: Simplified coupled engine block-crankshaft models
based on beam theory provide an efficient substitute to engine
simulation in the design process. These models require accurate
definition of the main bearing stiffness. In this paper, an investigation
of this stiffness is presented. The clearance effect is studied using a
smooth bearing model. It is manifested for low shaft displacement.
The hydrodynamic assessment model shows that the oil film has no
stiffness for low loads and it is infinitely rigid for important loads.
The deformation stiffness is determined using a suitable finite
elements model based on real CADs. As a result, a main bearing
behaviour law is proposed. This behaviour law takes into account the
clearance, the hydrodynamic sustention and the deformation stiffness.
It ensures properly the transition from the configuration low rigidity
to the configuration high rigidity.
Abstract: The focus of this research is in the area of the soviet period and the mission of the Russian Orthodox Church in Kazakhstan in the XIX century. There was close connection of national customs and traditions with religious practices, outlooks and attitudes. In particular, such an approach has alleged estimation by Kazakh historians of the process of Christianization of the local population. Some of them are inclined to consider the small number of Christening Kazakhs as evidence that the Russian Orthodox Church didn’t achieve its mission. The number of historians who think that the church didn’t achieve its mission has thousand over the last centuries, however our calculations of the number of Kazakhs who became Orthodox Christian is much more than other historians think. Such Christians can be divided into 3 groups: Some remained Christian until their deaths, others had two faiths and the third hid their true religions, having returned to their former belief. Therefore, to define the exact amount of Christening Kazakhs represented a challenge. Some data does not create a clear picture of the level of Christianization, constant and accurate was not collected. The data appearing in reports of spiritual attendants and civil authorities is not always authentic. Article purpose is illumination and the analysis missionary activity of Russian Orthodox Church in Kazakhstan.
Abstract: This paper tries to study the effect of geosynthetic inclusion on the improvement of the load-settlement characters of two layered soil. In addition, the effect of geogrid and geotextile in reduction of the required thickness of subbase layer in unpaved roads is studied. Considering the vast application of bearing ratio tests in road construction projects, this test is used in present investigation. Bearing ratio tests were performed on two layered soil including a granular soil layer at the top (as the subbase layer) and a weak clayey soil placed at the bottom (as the subgrade layer). These tests were performed for different conditions including unreinforced and reinforced by geogrid and geotextile and three thicknesses for top layer soil (subbase layer). In the reinforced condition the reinforcing element was placed on the interface of the top granular layer and the beneath clayey layer to study the separation effect of geosynthetics. In all tests the soils (both granular and clayey soil layers) were compacted according to optimum water content. At the end, the diagrams were plotted and were compared with each other. Furthermore, a comparison between geogrids and geotextiles behaviors on two layer soil is done in this paper. The results show an increase in compression strength of reinforced specimen in comparison with unreinforced soil sample. The effect of geosynthetic inclusion reduces by increasing the subbase thickness. In addition it was found that geogrids have more desirable behavior rather than geotextiles due to interlocking with the subbase layer aggregates.
Abstract: 53 college students answered questions regarding the circumstances in which they first heard about the news of Wenchuan earthquake or the news of their acceptance to college which took place approximately one year ago, and answered again two years later. The number of details recalled about their circumstances for both events was high and didn-t decline two years later. However, consistency in reported details over two years was low. Participants were more likely to construct central (e.g., Where were you?) than peripheral information (What were you wearing?), and the confidence of the central information was higher than peripheral information, which indicated that they constructed more when they were more confident.
Abstract: With respect to the dissipation of energy through
plastic deformation of joints of prefabricated wall units, the paper
points out the principal importance of efficient reinforcement of the
prefabricated system at its joints. The method, quality and amount of
reinforcement are essential for reaching the necessary degree of joint
ductility. The paper presents partial results of experimental research
of vertical joints of prefabricated units exposed to monotonously
rising loading and repetitive shear force and formulates a conclusion
that the limit state of the structure as a whole is preceded by the
disintegration of joints, or that the structure tends to pass from
linearly elastic behaviour to non-linearly elastic to plastic behaviour
by exceeding the proportional elastic limit in joints.Experimental
verification on a model of a 7-storey prefabricated structure revealed
weak points in its load-bearing systems, mainly at places of critical
points around openings situated in close proximity to vertical joints
of mutually perpendicularly oriented walls.
Abstract: In this study Vitaton (an organic supplement which
contains fermentative β-carotene) and synthetic astaxanthin
(CAROPHYLL® Pink) were evaluated as pro-growth factors in
Rainbow trout diet. An 8 week feeding trial was conducted to
determine the effects of Vitaton versus astaxanthin on rearing factors,
survival rate and visual flesh color of Rainbow trout
(Oncorhnchynchus mykiss) with initial weight of 196±5. Four
practical diets were formulated to contain 50 and 80 (ppm) of β-
carotene and astaxanthin and also a control diet was prepared without
any pigment. Each diet was fed to triplicate groups of fish rearing in
fresh water. Fish were fed twice daily. The water temperature
fluctuated from 12 to 15 (C˚) and also dissolved oxygen content was
between 7 to 7.5 (mg/lit) during the experimental period. At the end
of the experiment, growth and food utilization parameters and
survival rate were unaffected by dietary treatments (p>0.05). Also,
there was no significant difference between carcass yield within
treatments (p>0.05). No significant difference recognized between
visual flesh color (SalmoFan score) of fish fed Vitaton-containing
diets. On the contrary, feeding on diets containing 50 and 80 (ppm)
of astaxanthin, increased SalmoFan score (flesh astaxanthin
concentration) from
Abstract: The design of a pattern classifier includes an attempt
to select, among a set of possible features, a minimum subset of
weakly correlated features that better discriminate the pattern classes.
This is usually a difficult task in practice, normally requiring the
application of heuristic knowledge about the specific problem
domain. The selection and quality of the features representing each
pattern have a considerable bearing on the success of subsequent
pattern classification. Feature extraction is the process of deriving
new features from the original features in order to reduce the cost of
feature measurement, increase classifier efficiency, and allow higher
classification accuracy. Many current feature extraction techniques
involve linear transformations of the original pattern vectors to new
vectors of lower dimensionality. While this is useful for data
visualization and increasing classification efficiency, it does not
necessarily reduce the number of features that must be measured
since each new feature may be a linear combination of all of the
features in the original pattern vector. In this paper a new approach is
presented to feature extraction in which feature selection, feature
extraction, and classifier training are performed simultaneously using
a genetic algorithm. In this approach each feature value is first
normalized by a linear equation, then scaled by the associated weight
prior to training, testing, and classification. A knn classifier is used to
evaluate each set of feature weights. The genetic algorithm optimizes
a vector of feature weights, which are used to scale the individual
features in the original pattern vectors in either a linear or a nonlinear
fashion. By this approach, the number of features used in classifying
can be finely reduced.
Abstract: Protective clothing limits heat transfer and hampers
task performance due to the increased weight. Militarism protective
clothing enables humans to operate in adverse environments. In the
selection and evaluation of militarism protective clothing attention
should be given to heat strain, ergonomic and fit issues next to the
actual protection it offers.
Fifty Male healthy subjects participated in the study. The subjects
were dressed in shorts, T-shirts, socks, sneakers and four deferent
kinds of militarism protective clothing such as CS, CSB, CS with
NBC protection and CS with NBC- protection added.
Ergonomically and psychological strains of every four cloths were
investigated on subjects by walking on a treadmill (7km/hour) with a
19.7 kg backpack. As a result of these tests were showed that, the
highest heart rate was found wearing the NBC-protection added
outfit, the highest temperatures were observed wearing NBCprotection
added, followed by respectively CS with NBC protection,
CSB and CS and the highest value for thermal comfort (implying
worst thermal comfort) was observed wearing NBC-protection
added.
Abstract: The paper examines the performance of bit-interleaved parity (BIP) methods in error rate monitoring, and in declaration and clearing of alarms in those transport networks that employ automatic protection switching (APS). The BIP-based error rate monitoring is attractive for its simplicity and ease of implementation. The BIP-based results are compared with exact results and are found to declare the alarms too late, and to clear the alarms too early. It is concluded that the standards development and systems implementation should take into account the fact of early clearing and late declaration of alarms. The window parameters defining the detection and clearing thresholds should be set so as to build sufficient hysteresis into the system to ensure that BIP-based implementations yield acceptable performance results.
Abstract: An experiment was conducted to determine the effect
of the rearing system on growth performance, carcass yield,
hematological parameters, and feather pecking damage of Thai
indigenous chickens. Three hundred and sixty 1-d-old chicks were
randomly assigned to 2 treatments: indoor treatment and outdoor
access treatment. In the indoor treatment, the chickens were housed
in floor pens (5 birds/m2). In the outdoor access treatment, the
chickens were housed in a similar indoor house; in addition, they also
had an outdoor grass paddock (1 bird/m2). All birds were provided
with same diet and were raised for 16 wk of age. The results showed
that growth performance and carcass yield were not different among
treatment (P>0.05). Outdoor access had no effect on hematological
parameters (P>0.05). However, the feather pecking damage of the
chickens in the outdoor access treatment was lower than that of the
chickens in the indoor treatment (P
Abstract: This research is to design and implement a new kind
of agitators called differential agitator. The Differential Agitator is an
electro- mechanic set consists of two shafts. The first shaft is the
bearing axis while the second shaft is the axis of the quartet upper
bearing impellers group and the triple lower group which are called
as agitating group. The agitating group is located inside a cylindrical
container equipped especially to contain square directors for the
liquid entrance and square directors called fixing group for the liquid
exit. The fixing group is installed containing the agitating group
inside any tank whether from upper or lower position. The agitating
process occurs through the agitating group bearing causing a lower
pressure over the upper group leading to withdrawing the liquid from
the square directors of the liquid entering and consequently the liquid
moves to the denser place under the quartet upper group. Then, the
liquid moves to the so high pressure area under the agitating group
causing the liquid to exit from the square directors in the bottom of
the container. For improving efficiency, parametric study and shape
optimization has been carried out. A numerical analysis,
manufacturing and laboratory experiments were conducted to design
and implement the differential agitator. Knowing the material
prosperities and the loading conditions, the FEM using ANSYS11
was used to get the optimum design of the geometrical parameters of
the differential agitator elements while the experimental test was
performed to validate the advantages of the differential agitators to
give a high agitation performance of lime in the water as an example.
In addition, the experimental work has been done to express the
internal container shape in the agitation efficiency. The study ended
up with conclusions to maximize agitator performance and optimize
the geometrical parameters to be used for manufacturing the
differential agitator
Abstract: This study was conducted to investigate the efficacy
of five herbicides on narrow leaved weeds and growth and yield of
wheat. An experiment was conducted at Agronomic Research
Farm, University of Agriculture Faisalabad. The experiment was
laid out in randomized complete block designee (RCBD) with three
replications. Treatments studied were clodinafop (Topic-15 WG) at
37 g a.i. ha-1, clodinafop (Topaz-15 WG) at 45 g a.i. ha-1,
fenoxaprop-p-ethyl (Puma Super-75 EW) at 45 g a.i. ha-1,
fenoxaprop-p-ethyl (Gramicide-6.9 EW) at 85 g a.i. ha-1,
fenoxaprop-p-ethyl (Chinlima-6.9 EW) at 85 g a.i. ha-1 and weedy
check. Plots treated with fenoxaprop-p-ethyl (Puma Super-75 EW)
at 45 g a.i. ha-1 produced relatively less weed biomass, more plant
height, number of spike bearing tillers, number of grains per spike,
1000-grain weight and grain yield (4.20 t ha-1).
Abstract: A subjectively influenced router for vehicles in a fourjunction
traffic system is presented. The router is based on a 3-layer
Backpropagation Neural Network (BPNN) and a greedy routing
procedure. The BPNN detects priorities of vehicles based on the
subjective criteria. The subjective criteria and the routing procedure
depend on the routing plan towards vehicles depending on the user.
The routing procedure selects vehicles from their junctions based on
their priorities and route them concurrently to the traffic system. That
is, when the router is provided with a desired vehicles selection
criteria and routing procedure, it routes vehicles with a reasonable
junction clearing time. The cost evaluation of the router determines
its efficiency. In the case of a routing conflict, the router will route
the vehicles in a consecutive order and quarantine faulty vehicles.
The simulations presented indicate that the presented approach is an
effective strategy of structuring a subjective vehicle router.