Abstract: Submerged arc welding is a very complex process. It
is a very efficient and high performance welding process. In this
present study an attempt have been done to reduce the welding
distortion by increased amount of oxide flux through TiO2 in
submerged arc welding process. Care has been taken to avoid the
excessiveness of the adding agent for attainment of significant
results. Data Envelopment Analysis (DEA) based BAT algorithm is
used for the parametric optimization purpose in which DEA is used
to convert multi response parameters into a single response
parameter. The present study also helps to know the effectiveness of
the addition of TiO2 in active flux during submerged arc welding
process.
Abstract: The formulated problem of optimization of the
technological process of water treatment for thermal power plants is
considered in this article. The problem is of multiparametric nature.
To optimize the process, namely, reduce the amount of waste water, a
new technology was developed to reuse such water. A mathematical
model of the technology of wastewater reuse was developed.
Optimization parameters were determined. The model consists of a
material balance equation, an equation describing the kinetics of ion
exchange for the non-equilibrium case and an equation for the ion
exchange isotherm. The material balance equation includes a
nonlinear term that depends on the kinetics of ion exchange. A direct
problem of calculating the impurity concentration at the outlet of the
water treatment plant was numerically solved. The direct problem
was approximated by an implicit point-to-point computation
difference scheme. The inverse problem was formulated as relates to
determination of the parameters of the mathematical model of the
water treatment plant operating in non-equilibrium conditions. The
formulated inverse problem was solved. Following the results of
calculation the time of start of the filter regeneration process was
determined, as well as the period of regeneration process and the
amount of regeneration and wash water. Multi-parameter
optimization of water treatment process for thermal power plants
allowed decreasing the amount of wastewater by 15%.
Abstract: This paper introduces an original method of
parametric optimization of the structure for multimodal decisionlevel
fusion scheme which combines the results of the partial solution
of the classification task obtained from assembly of the mono-modal
classifiers. As a result, a multimodal fusion classifier which has the
minimum value of the total error rate has been obtained.
Abstract: Analytical expressions of the current and angular errors, as well as the frequency characteristics of an induction converter describing the relation with its structural parameters, the core and winding characteristics are obtained. Based on estimation of the dependences obtained, a mathematical problem of parametric optimization is formulated which can successfully be used for investigating and diagnosing an induction converter.
Abstract: Ultrasonic machining (USM) is a non-traditional
machining process being widely used for commercial machining of
brittle and fragile materials such as glass, ceramics and
semiconductor materials. However, USM could be a viable
alternative for machining a tough material such as titanium; and this
aspect needs to be explored through experimental research. This
investigation is focused on exploring the use of ultrasonic machining
for commercial machining of pure titanium (ASTM Grade-I) and
evaluation of tool wear rate (TWR) under controlled experimental
conditions. The optimal settings of parameters are determined
through experiments planned, conducted and analyzed using Taguchi
method. In all, the paper focuses on parametric optimization of
ultrasonic machining of pure titanium metal with TWR as response,
and validation of the optimized value of TWR by conducting
confirmatory experiments.
Abstract: In the present investigation, H13 tool steel has been
deposited on copper alloy substrate using both CO2 and diode laser.
A detailed parametric analysis has been carried out in order to find
out optimum processing zone for coating defect free H13 tool steel
on copper alloy substrate. Followed by parametric optimization, the
microstructure and microhardness of the deposited clads have been
evaluated. SEM micrographs revealed dendritic microstructure in
both clads. However, the microhardness of CO2 laser deposited clad
was much higher compared to diode laser deposited clad.
Abstract: In this paper, a novel approach for the multidisciplinary design optimization (MDO) of complex mechatronic systems. This approach, which is a part of a global project aiming to include the MDO aspect inside an innovative design process. As a first step, the paper considers the MDO as a redesign approach which is limited to the parametric optimization. After defining and introducing the different keywords, the proposed method which is based on the V-Model which is commonly used in mechatronics.
Abstract: This research is to design and implement a new kind
of agitators called differential agitator. The Differential Agitator is an
electro- mechanic set consists of two shafts. The first shaft is the
bearing axis while the second shaft is the axis of the quartet upper
bearing impellers group and the triple lower group which are called
as agitating group. The agitating group is located inside a cylindrical
container equipped especially to contain square directors for the
liquid entrance and square directors called fixing group for the liquid
exit. The fixing group is installed containing the agitating group
inside any tank whether from upper or lower position. The agitating
process occurs through the agitating group bearing causing a lower
pressure over the upper group leading to withdrawing the liquid from
the square directors of the liquid entering and consequently the liquid
moves to the denser place under the quartet upper group. Then, the
liquid moves to the so high pressure area under the agitating group
causing the liquid to exit from the square directors in the bottom of
the container. For improving efficiency, parametric study and shape
optimization has been carried out. A numerical analysis,
manufacturing and laboratory experiments were conducted to design
and implement the differential agitator. Knowing the material
prosperities and the loading conditions, the FEM using ANSYS11
was used to get the optimum design of the geometrical parameters of
the differential agitator elements while the experimental test was
performed to validate the advantages of the differential agitators to
give a high agitation performance of lime in the water as an example.
In addition, the experimental work has been done to express the
internal container shape in the agitation efficiency. The study ended
up with conclusions to maximize agitator performance and optimize
the geometrical parameters to be used for manufacturing the
differential agitator
Abstract: The advantage of solving the complex nonlinear
problems by utilizing fuzzy logic methodologies is that the
experience or expert-s knowledge described as a fuzzy rule base can
be directly embedded into the systems for dealing with the problems.
The current limitation of appropriate and automated designing of
fuzzy controllers are focused in this paper. The structure discovery
and parameter adjustment of the Branched T-S fuzzy model is
addressed by a hybrid technique of type constrained sparse tree
algorithms. The simulation result for different system model is
evaluated and the identification error is observed to be minimum.
Abstract: The paper presents the virtual model of the active
suspension system used for improving the dynamic behavior of a
motor vehicle. The study is focused on the design of the control
system, the purpose being to minimize the effect of the road
disturbances (which are considered as perturbations for the control
system). The analysis is performed for a quarter-car model, which
corresponds to the suspension system of the front wheel, by using the
DFC (Design for Control) software solution EASY5 (Engineering
Analysis Systems) of MSC Software. The controller, which is a PIDbased
device, is designed through a parametric optimization with the
Matrix Algebra Tool (MAT), considering the gain factors as design
variables, while the design objective is to minimize the overshoot of
the indicial response.
Abstract: Present paper presents a parametric performancebased
design model for optimizing hospital design. The design model
operates with geometric input parameters defining the functional
requirements of the hospital and input parameters in terms of
performance objectives defining the design requirements and
preferences of the hospital with respect to performances. The design
model takes point of departure in the hospital functionalities as a set
of defined parameters and rules describing the design requirements
and preferences.