Abstract: The stability characteristics of water lubricated journal bearings having three axial grooves are obtained theoretically. In this lubricant (water) is fed under pressure from one end of the bearing, through the 3-axial grooves (groove angles may vary). These bearings can use the process fluid as the lubricant, as in the case of feed water pumps. The Reynolds equation is solved numerically by the finite difference method satisfying the boundary conditions. The stiffness and damping coefficient for various bearing number and eccentricity ratios, assuming linear pressure drop along the groove, shows that smaller groove angles better results.
Abstract: The flow field within the combustor of scramjet
engine is very complex and poses a considerable challenge in the
design and development of a supersonic combustor with an optimized
geometry. In this paper comprehensive numerical studies on flow
field characteristics of different cavity based scramjet combustors
with transverse injection of hydrogen have been carried out for both
non-reacting and reacting flows. The numerical studies have been
carried out using a validated 2D unsteady, density based 1st-order
implicit k-omega turbulence model with multi-component finite rate
reacting species. The results show a wide variety of flow features
resulting from the interactions between the injector flows, shock
waves, boundary layers, and cavity flows. We conjectured that an
optimized cavity is a good choice to stabilize the flame in the
hypersonic flow, and it generates a recirculation zone in the scramjet
combustor. We comprehended that the cavity based scramjet
combustors having a bearing on the source of disturbance for the
transverse jet oscillation, fuel/air mixing enhancement, and flameholding
improvement. We concluded that cavity shape with
backward facing step and 45o forward ramp is a good choice to get
higher temperatures at the exit compared to other four models of
scramjet combustors considered in this study.
Abstract: In this paper, the babbitting of a bearing in boiler feed pump of an electromotor has been studied. These bearings have an important role in reducing the shut down times in the pumps, compressors and turbines. The most conventional method in babbitting is casting as a melting method. The comparison between thermal spray and casting methods in babbitting shows that the thermal spraying babbitt layer has better performance and tribological behavior. The metallurgical and tribological analysis such as SEM, EDS and wet chemical analysis has been made in the Babbitt alloys and worn surfaces. Two type of babbitt materials: tinbase and lead-base babbitt was used. The benefits of thermally sprayed babbitt layers are completely clear especially in large bearings.
Abstract: Today, Hydroforming technology provides an
attractive alternative to conventional matched die forming, especially
for cost-sensitive, lower volume production, and for parts with
irregular contours. In this study the critical fluid pressures which lead
to rupture in the workpiece has been investigated by theoretical and
finite element methods. The axisymmetric analysis was developed to
investigate the tearing phenomenon in cylindrical Hydroforming
Deep Drawing (HDD). By use of obtained equations the effect of
anisotropy, drawing ratio, sheet thickness and strain hardening
exponent on tearing diagram were investigated.
Abstract: An investigation of noise in a micro stepping motor is
considered to study in this article. Because of the trend towards higher
precision and more and more small 3C (including Computer,
Communication and Consumer Electronics) products, the micro
stepping motor is frequently used to drive the micro system or the
other 3C products. Unfortunately, noise in a micro stepped motor is
too large to accept by the customs. To depress the noise of a micro
stepped motor, the dynamic characteristics in this system must be
studied. In this article, a Visual Basic (VB) computer program speed
controlled micro stepped motor in a digital camera is investigated.
Karman KD2300-2S non-contract eddy current displacement sensor,
probe microphone, and HP 35670A analyzer are employed to analyze
the dynamic characteristics of vibration and noise in a motor. The
vibration and noise measurement of different type of bearings and
different treatment of coils are compared. The rotating components,
bearings, coil, etc. of the motor play the important roles in producing
vibration and noise. It is found that the noise will be depressed about
3~4 dB and 6~7 dB, when substitutes the copper bearing with plastic
one and coats the motor coil with paraffin wax, respectively.
Abstract: Nowadays, quick technological changes force companies
to develop innovative products in an increasingly competitive
environment. Therefore, how to enhance the time of new product
development is very important. This design problem often lacks
the exact formula for getting it, and highly depends upon human
designers- past experiences. For these reasons, in this work, a Casebased
reasoning (CBR) system to assist in new product development
is proposed. When a case is recovered from the case base, the system
will take into account not only the attribute-s specific value and
how important it is. It will also take into account if the attribute
has a positive influence over the product development. Hence the
manufacturing time will be improved. This information will be
introduced as a new concept called “adaptability". An application to
this method for hearing instrument new design illustrates the proposed
approach.
Abstract: Chaiyaphum Starch Co. Ltd. is one of many starch
manufacturers that has introduced machinery to aid in manufacturing.
Even though machinery has replaced many elements and is now a
significant part in manufacturing processes, problems that must be
solved with respect to current process flow to increase efficiency still
exist. The paper-s aim is to increase productivity while maintaining
desired quality of starch, by redesigning the flipping machine-s
mechanical control system which has grossly low functional lifetime.
Such problems stem from the mechanical control system-s bearings,
as fluids and humidity can access into said bearing directly, in
tandem with vibrations from the machine-s function itself. The wheel
which is used to sense starch thickness occasionally falls from its
shaft, due to high speed rotation during operation, while the shaft
may bend from impact when processing dried bread. Redesigning its
mechanical control system has increased its efficiency, allowing
quality thickness measurement while increasing functional lifetime
an additional 62 days.
Abstract: The cable tower of Liede Bridge is a double-column curved-lever arched-beam portal framed structure. Being novel and unique in structure, its cable tower differs in complexity from traditional ones. This paper analyzes the ultimate load capacity of cable tower by adopting the finite element calculations and model tests which indicate that constitutive relations applied here give a better simulation of actual failure process of prestressed reinforced concrete. In vertical load, horizontal load and overloading tests, the stepped loading of the tower model is of linear relationship, and the test data has good repeatability. All suggests that the cable tower has good bearing capacity, rational design and high emergency capacity.
Abstract: The experiment was conducted to study the effect of
rearing systems on fatty acid composition and cholesterol content of
Thai indigenous chicken meat. Three hundred and sixty chicks were
allocated to 2 different rearing systems: conventional, housing in an
indoor pen (5 birds/m2); free-range, housing in an indoor pen (5
birds/m2) with access to a grass paddock (1 bird/m2) from 8 wk of age
until slaughter. All birds were provided with the same diet during the
experimental period. At 16 wk of age, 24 birds per group were
slaughtered to evaluate the fatty acid composition and cholesterol
content of breast and thigh meat. The results showed that the
proportion of SFA, MUFA and PUFA in breast and thigh meat were
not different among groups (P>0.05). However, the proportion of n-3
fatty acids was higher and the ratio of n-6 to n-3 fatty acids was lower
in free-range system than in conventional system (P0.05). The data indicated that the free-range system
could increase the proportion of n-3 fatty acids, but no effect on
cholesterol content in Thai indigenous chicken meat.
Abstract: Restructured electricity markets may provide
opportunities for producers to exercise market power maintaining
prices in excess of competitive levels. In this paper an oligopolistic
market is presented that all Generation Companies (GenCos) bid in a
Cournot model. Genetic algorithm (GA) is applied to obtain
generation scheduling of each GenCo as well as hourly market
clearing prices (MCP). In order to consider network constraints a
multiperiod framework is presented to simulate market clearing
mechanism in which the behaviors of market participants are
modelled through piecewise block curves. A mixed integer linear
programming (MILP) is employed to solve the problem. Impacts of
market clearing process on participants- characteristic and final
market prices are presented. Consequently, a novel multi-objective
model is addressed for security constrained optimal bidding strategy
of GenCos. The capability of price-maker GenCos to alter MCP is
evaluated through introducing an effective-supply curve. In addition,
the impact of exercising market power on the variation of market
characteristics as well as GenCos scheduling is studied.
Abstract: The use of human hand as a natural interface for humancomputer interaction (HCI) serves as the motivation for research in hand gesture recognition. Vision-based hand gesture recognition involves visual analysis of hand shape, position and/or movement. In this paper, we use the concept of object-based video abstraction for segmenting the frames into video object planes (VOPs), as used in MPEG-4, with each VOP corresponding to one semantically meaningful hand position. Next, the key VOPs are selected on the basis of the amount of change in hand shape – for a given key frame in the sequence the next key frame is the one in which the hand changes its shape significantly. Thus, an entire video clip is transformed into a small number of representative frames that are sufficient to represent a gesture sequence. Subsequently, we model a particular gesture as a sequence of key frames each bearing information about its duration. These constitute a finite state machine. For recognition, the states of the incoming gesture sequence are matched with the states of all different FSMs contained in the database of gesture vocabulary. The core idea of our proposed representation is that redundant frames of the gesture video sequence bear only the temporal information of a gesture and hence discarded for computational efficiency. Experimental results obtained demonstrate the effectiveness of our proposed scheme for key frame extraction, subsequent gesture summarization and finally gesture recognition.
Abstract: Particulate reinforced metal matrix composites
(MMCs) are potential materials for various applications due to their
advantageous of physical and mechanical properties. This paper
presents a study on the performance of stir cast Al2O3 SiC reinforced
metal matrix composite materials. The results indicate that the
composite materials exhibit improved physical and mechanical
properties, such as, low coefficient of thermal expansion, high
ultimate tensile strength, high impact strength, and hardness. It has
been found that with the increase of weight percentage of
reinforcement particles in the aluminium metal matrix, the new
material exhibits lower wear rate against abrasive wearing. Being
extremely lighter than the conventional gray cast iron material, the
Al-Al2O3 and Al-SiC composites could be potential green materials
for applications in the automobile industry, for instance, in making
car disc brake rotors.
Abstract: This paper aims to study the methodology of building the knowledge of planning adequate punches in order to complete the task of strip layout for shearing processes, using progressive dies. The proposed methodology uses die design rules and characteristics of different types of punches to classify them into five groups: prior use (the punches must be used first), posterior use (must be used last), compatible use (may be used together), sequential use (certain punches must precede some others) and simultaneous use (must be used together). With these five groups of punches, the searching space of feasible designs will be greatly reduced, and superimposition becomes a more effective method of punch layout. The superimposition scheme will generate many feasible solutions, an evaluation function based on number of stages, moment balancing and strip stability is developed for helping designers to find better solutions.
Abstract: A mathematical model for determining the overall efficiency
of a multistage tractor gearbox including all gear, lubricant,
surface finish related parameters and operating conditions is
presented. Sliding friction, rolling friction and windage losses were
considered as the main sources of power loss in the gearing system. A
computer code in FORTRAN was developed to simulate the model.
Sliding friction contributes about 98% of the total power loss for
gear trains operating at relatively low speeds (less than 2000 rpm
input speed). Rolling frictional losses decrease with increased load
while windage losses are only significant for gears running at very
high speeds (greater than 3000 rpm). The results also showed that the
overall efficiency varies over the path of contact of the gear meshes
ranging between 94% to 99.5%.
Abstract: The aim of the paper work is to investigate and predict
the static performance of journal bearing in turbulent flow condition
considering micropolar lubrication. The Reynolds equation has been
modified considering turbulent micropolar lubrication and is solved
for steady state operations. The Constantinescu-s turbulence model is
adopted using the coefficients. The analysis has been done for a
parallel and inertia less flow. Load capacity and friction factor have
been evaluated for various operating parameters.
Abstract: Khatunabad area is situated geologically in Urmieh-
Dokhtar magmatic belt in NW of Iran. In this research, studied area
has been investigated in order to recognize the potential copper and
molybdenum-bearing target areas. The survey layers include the
lithologic units, alteration, geochemical result, tectonics and copper
and molybdenum occurrence. As an accurate decision can have a
considerable effect on exploration plans, so in this efforts have been
made to make use of new combination method. For this purpose, the
analytical hierarchy process was used and revealed highly potential
copper and molybdenum mineralization areas. Based on achieved
results, geological perspective in north of studied area is appropriate
for advance stage, especially for subsurface exploration in future.
Abstract: The paper is included within the framework of a
complex research program, which was initiated from the hypothesis
arguing on the existence of a correlation between pineal indolic and
peptide hormones and the somatic development rhythm, including
thus the epithalamium-epiphysis complex involvement. At birds,
pineal gland contains a circadian oscillator, playing a main role in the
temporal organization of the cerebral functions. The secretion of
pineal indolic hormones is characterized by a high endogenous
rhythmic alternation, modulated by the light/darkness (L/D)
succession and by temperature as well. The research has been carried
out using 100 chicken broilers - “Ross" commercial hybrid,
randomly allocated in two experimental batches: Lc batch, reared
under a 12L/12D lighting schedule and Lexp batch, which was photic
pinealectomised through continuous exposition to light (150 lux, 24
hours, 56 days). Chemical and physical features of the meat issued
from breast fillet and thighs muscles have been studied, determining
the dry matter, proteins, fat, collagen, salt content and pH value, as
well. Besides the variations of meat chemical composition in relation
with lighting schedule, other parameters have been studied: live
weight dynamics, feed intake and somatic development degree. The
achieved results became significant since chickens have 7 days of
age, some variations of the studied parameters being registered,
revealing that the pineal gland physiologic activity, in relation with
the lighting schedule, could be interpreted through the monitoring of
the somatic development technological parameters, usually studied
within the chicken broilers rearing aviculture practice.
Abstract: Pressure vessels are usually operating at temperatures
where the conditions of linear elastic fracture mechanics are no
longer met because massive plasticity precedes crack propagation. In
this work the development of a surface crack in a pressure vessel
subject to bending and tension under elastic-plastic fracture
mechanics conditions was investigated. Finite element analysis was
used to evaluate the hydrostatic stress, the J-integral and crack
growth for semi-elliptical surface-breaking cracks. The results
showed non-uniform stress triaxiality and crack driving force around
the crack front at large deformation levels. Different ductile crack
extensions were observed which emphasis the dependent of ductile
tearing on crack geometry and type of loading. In bending the crack
grew only beneath the surface, and growth was suppressed at the
deepest segment. This contrasts to tension where the crack breaks
through the thickness with uniform growth along the entire crack
front except at the free surface. Current investigations showed that
the crack growth developed under linear elastic fracture mechanics
conditions will no longer be applicable under ductile tearing
scenarios.
Abstract: GFRG(Glass Fiber Reinforced Gypsum) wall is a green product which can erect a building fast in prefabricated method, but its application to high-rise residential buildings is limited for its poor lateral stiffness. This paper has proposed a modification to GFRG walls structure to increase its lateral stiffness, which aiming to erect small high-rise residential buildings as load-bearing walls. The elastic finite element analysis to it has shown the lateral deformation feature and the distributions of the axial force and the shear force. The analysis results show that the new GFRG reinforced concrete wall can be used for small high-rise residential buildings.
Abstract: A new analysis of perceptual speech enhancement is
presented. It focuses on the fact that if only noise above the masking
threshold is filtered, then noise below the masking threshold, but
above the absolute threshold of hearing, can become audible after the
masker filtering. This particular drawback of some perceptual filters,
hereafter called the maskee-to-audible-noise (MAN) phenomenon,
favours the emergence of isolated tonals that increase musical noise.
Two filtering techniques that avoid or correct the MAN phenomenon
are proposed to effectively suppress background noise without introducing
much distortion. Experimental results, including objective
and subjective measurements, show that these techniques improve
the enhanced speech quality and the gain they bring emphasizes the
importance of the MAN phenomenon.