Abstract: Since Network-on-Chip (NoC) uses network
interfaces (NIs) to improve the design productivity, by now, there
have been a few papers addressing the design and implementation of a
NI module. However, none of them considered the difference of
address encoding methods between NoC and the traditional
bus-shared architecture. On the basis of this difference, in the paper,
we introduce a transmit mechanism to solve such a problem for global
asynchronous locally synchronous (GALS) NoC. Furthermore, we
give the concrete implementation of the NI module in this transmit
mechanism. Finally, we evaluate its performance and area overhead
by a VHDL-based cycle-accurate RTL model and simulation results
confirm the validity of this address-oriented transmit mechanism.
Abstract: High-velocity oxygen fuel (HVOF) thermal spraying
uses a combustion process to heat the gas flow and coating material.
A computational fluid dynamics (CFD) model has been developed to
predict gas dynamic behavior in a HVOF thermal spray gun in which
premixed oxygen and propane are burnt in a combustion chamber
linked to a parallel-sided nozzle. The CFD analysis is applied to
investigate axisymmetric, steady-state, turbulent, compressible,
chemically reacting, subsonic and supersonic flow inside and outside
the gun. The gas velocity, temperature, pressure and Mach number
distributions are presented for various locations inside and outside
the gun. The calculated results show that the most sensitive
parameters affecting the process are fuel-to-oxygen gas ratio and
total gas flow rate. Gas dynamic behavior along the centerline of the
gun depends on both total gas flow rate and fuel-to-oxygen gas ratio.
The numerical simulations show that the axial gas velocity and Mach
number distribution depend on both flow rate and ratio; the highest
velocity is achieved at the higher flow rate and most fuel-rich ratio.
In addition, the results reported in this paper illustrate that the
numerical simulation can be one of the most powerful and beneficial
tools for the HVOF system design, optimization and performance
analysis.
Abstract: During the past several years, face recognition in video
has received significant attention. Not only the wide range of
commercial and law enforcement applications, but also the availability
of feasible technologies after several decades of research contributes
to the trend. Although current face recognition systems have reached a
certain level of maturity, their development is still limited by the
conditions brought about by many real applications. For example,
recognition images of video sequence acquired in an open
environment with changes in illumination and/or pose and/or facial
occlusion and/or low resolution of acquired image remains a largely
unsolved problem. In other words, current algorithms are yet to be
developed. This paper provides an up-to-date survey of video-based
face recognition research. To present a comprehensive survey, we
categorize existing video based recognition approaches and present
detailed descriptions of representative methods within each category.
In addition, relevant topics such as real time detection, real time
tracking for video, issues such as illumination, pose, 3D and low
resolution are covered.
Abstract: Excessive ductility demand on shorter piers is a
common problem for irregular bridges subjected to strong ground
motion. Various techniques have been developed to reduce the
likelihood of collapse of bridge due to failure of shorter piers. This
paper presents the new approach to improve the seismic behavior of
such bridges using Nitinol shape memory alloys (SMAs).
Superelastic SMAs have the ability to remain elastic under very large
deformation due to martensitic transformation. This unique property
leads to enhanced performance of controlled bridge compared with
the performance of the reference bridge. To evaluate the effectiveness
of the devices, nonlinear time history analysis is performed on a RC
single column bent highway bridge using a suite of representative
ground motions. The results show that this method is very effective in
limiting the ductility demand of shorter pier.
Abstract: .Hardware realization of a Neural Network (NN), to a large extent depends on the efficient implementation of a single neuron. FPGA-based reconfigurable computing architectures are suitable for hardware implementation of neural networks. FPGA realization of ANNs with a large number of neurons is still a challenging task. This paper discusses the issues involved in implementation of a multi-input neuron with linear/nonlinear excitation functions using FPGA. Implementation method with resource/speed tradeoff is proposed to handle signed decimal numbers. The VHDL coding developed is tested using Xilinx XC V50hq240 Chip. To improve the speed of operation a lookup table method is used. The problems involved in using a lookup table (LUT) for a nonlinear function is discussed. The percentage saving in resource and the improvement in speed with an LUT for a neuron is reported. An attempt is also made to derive a generalized formula for a multi-input neuron that facilitates to estimate approximately the total resource requirement and speed achievable for a given multilayer neural network. This facilitates the designer to choose the FPGA capacity for a given application. Using the proposed method of implementation a neural network based application, namely, a Space vector modulator for a vector-controlled drive is presented
Abstract: This paper reported an experimental research of
steady-state heat transfer behaviour of a gas flowing through a fixed
bed under the different operating conditions. Studies had been carried
out in a fixed-bed packed methanol synthesis catalyst percolated by air
at appropriate flow rate. Both radial and axial direction temperature
distribution had been investigated under the different operating
conditions. The effects of operating conditions including the reactor
inlet air temperature, the heating pipe temperature and the air flow rate
on temperature distribution was investigated and the experimental
results showed that a higher inlet air temperature was conducive to
uniform temperature distribution in the fixed bed. A large temperature
drop existed at the radial direction, and the temperature drop increased
with the heating pipe temperature increasing under the experimental
conditions; the temperature profile of the vicinity of the heating pipe
was strongly affected by the heating pipe temperature. A higher air
flow rate can improve the heat transfer in the fixed bed. Based on the
thermal distribution, heat transfer models of the fixed bed could be
established, and the characteristics of the temperature distribution in
the fixed bed could be finely described, that had an important practical
significance.
Abstract: Recently, web services to access from many type devices
are often used. We have developed the shortest path planning
system called "Bus-Net" in Tottori prefecture as a web application
to sustain the public transport. And it used the same user interface
for both devices. To support both devices, the interface cannot use
JavaScript and so on.
Thus, we developed the method that use individual user interface
for each device type to improve its convenience. To be concrete,
we defined formats of condition input to the path planning system
and result output from it and separate the system into the request
processing part and user interface parts that depend on device types.
By this method, we have also developed special device for Bus-Net
named "Intelligent-Bus-Stop".
Abstract: Image compression can improve the performance of
the digital systems by reducing time and cost in image storage
and transmission without significant reduction of the image quality.
Furthermore, the discrete cosine transform has emerged as the new
state-of-the art standard for image compression. In this paper, a
hybrid image compression technique based on reversible blockade
transform coding is proposed. The technique, implemented over
regions of interest (ROIs), is based on selection of the coefficients
that belong to different transforms, depending on the coefficients is
proposed. This method allows: (1) codification of multiple kernals
at various degrees of interest, (2) arbitrary shaped spectrum,and (3)
flexible adjustment of the compression quality of the image and the
background. No standard modification for JPEG2000 decoder was
required. The method was applied over different types of images.
Results show a better performance for the selected regions, when
image coding methods were employed for the whole set of images.
We believe that this method is an excellent tool for future image
compression research, mainly on images where image coding can
be of interest, such as the medical imaging modalities and several
multimedia applications. Finally VLSI implementation of proposed
method is shown. It is also shown that the kernal of Hartley and
Cosine transform gives the better performance than any other model.
Abstract: Patients with diabetes are susceptible to chronic foot
wounds which may be difficult to manage and slow to heal.
Diagnosis and treatment currently rely on the subjective judgement of
experienced professionals. An objective method of tissue assessment
is required. In this paper, a data fusion approach was taken to wound
tissue classification. The supervised Maximum Likelihood and
unsupervised Multi-Modal Expectation Maximisation algorithms
were used to classify tissues within simulated wound models by
weighting the contributions of both colour and 3D depth information.
It was found that, at low weightings, depth information could show
significant improvements in classification accuracy when compared
to classification by colour alone, particularly when using the
maximum likelihood method. However, larger weightings were
found to have an entirely negative effect on accuracy.
Abstract: TiO2/Ag composite films were prepared by
incorporating Ag in the pores of mesoporous TiO2 films using a
photoreduction method. The Ag nanoparticle sizes were in a range of
3.66-38.56 nm. The TiO2/Ag composite films were characterized by
X-ray diffraction (XRD), scanning electron microscopy (SEM) and
transmission electron microscropy (TEM). The TiO2 films and
TiO2/Ag composite films were immersed in a 0.3 mM N719 dye
solution and characterized by UV-Vis spectrophotometer. The
TiO2/Ag/N719 composite film showed that an optimal size of Ag
nanoparticles was 19.12 nm and, hence, gave the maximum optical
absorption spectra. The improved absorption was due to surface
plasmon resonance induced by the Ag nanoparticles to enhance the
absorption coefficient of the dye.
Abstract: The Taiwan government has started to promote the “Plain Landscape Afforestation and Greening Program" since 2002. A key task of the program was the payment for environmental services (PES), entitled the “Plain Landscape Afforestation Policy" (PLAP), which was certificated by the Executive Yuan on August 31, 2001 and enacted on January 1, 2002. According to the policy, it is estimated that the total area of afforestation will be 25,100 hectares by December 31, 2007. Until the end of 2007, the policy had been enacted for six years in total and the actual area of afforestation was 8,919.18 hectares. Among them, Taiwan Sugar Corporation (TSC) was accounted for 7,960 hectares (with 2,450.83 hectares as public service area) which occupied 86.22% of the total afforestation area; the private farmland promoted by local governments was accounted for 869.18 hectares which occupied 9.75% of the total afforestation area. Based on the above, we observe that most of the afforestation area in this policy is executed by TSC, and the achievement ratio by TSC is better than by others. It implies that the success of the PLAP is seriously related to the execution of TSC. The objective of this study is to analyze the relevant policy planning of TSC's participation in the PLAP, suggest complementary measures, and draw up effective adjustment mechanisms, so as to improve the effectiveness of executing the policy. Our main conclusions and suggestions are summarized as follows: 1. The main reason for TSC’s participation in the PLAP is based on their passive cooperation with the central government or company policy. Prior to TSC’s participation in the PLAP, their lands were mainly used for growing sugarcane. 2. The main factors of TSC's consideration on the selection of tree species are based on the suitability of land and species. The largest proportion of tree species is allocated to economic forests, and the lack of technical instruction was the main problem during afforestation. Moreover, the method of improving TSC’s future development in leisure agriculture and landscape business becomes a key topic. 3. TSC has developed short and long-term plans on participating in the PLAP for the future. However, there is no great willingness or incentive on budgeting for such detailed planning. 4. Most people from TSC interviewed consider the requirements on PLAP unreasonable. Among them, an unreasonable requirement on the number of trees accounted for the greatest proportion; furthermore, most interviewees suggested that the government should continue to provide incentives even after 20 years. 5. Since the government shares the same goals as TSC, there should be sufficient cooperation and communication that support the technical instruction and reduction of afforestation cost, which will also help to improve effectiveness of the policy.
Abstract: The objective of this research was to investigate biodegradation of water hyacinth (Eichhornia crassipes) to produce bioethanol using dilute-acid pretreatment (1% sulfuric acid) results in high hemicellulose decomposition and using yeast (Pachysolen tannophilus) as bioethanol producing strain. A maximum ethanol yield of 1.14g/L with coefficient, 0.24g g-1; productivity, 0.015g l-1h-1 was comparable to predicted value 32.05g/L obtained by Central Composite Design (CCD). Maximum ethanol yield coefficient was comparable to those obtained through enzymatic saccharification and fermentation of acid hydrolysate using fully equipped fermentor. Although maximum ethanol concentration was low in lab scale, the improvement of lignocellulosic ethanol yield is necessary for large scale production.
Abstract: Business process automation is an important task in an
enterprise business environment software development. The
requirements of processing acceleration and automation level of
enterprises are inherently different from one organization to another.
We present a methodology and system for automation of business
process management system architecture by multi-agent collaboration
based on SOA. Design layer processes are modeled in semantic
markup language for web services application. At the core of our
system is considering certain types of human tasks to their further
automation across over multiple platform environments. An
improved abnormality processing with model for automation of
BPMS architecture by multi-agent collaboration based on SOA is
introduced. Validating system for efficiency of process automation,
an application for educational knowledge base instance would also be
described.
Abstract: This paper investigates the application of Particle Swarm Optimization (PSO) technique for coordinated design of a Power System Stabilizer (PSS) and a Thyristor Controlled Series Compensator (TCSC)-based controller to enhance the power system stability. The design problem of PSS and TCSC-based controllers is formulated as a time domain based optimization problem. PSO algorithm is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. To compare the capability of PSS and TCSC-based controller, both are designed independently first and then in a coordinated manner for individual and coordinated application. The proposed controllers are tested on a weakly connected power system. The eigenvalue analysis and non-linear simulation results are presented to show the effectiveness of the coordinated design approach over individual design. The simulation results show that the proposed controllers are effective in damping low frequency oscillations resulting from various small disturbances like change in mechanical power input and reference voltage setting.
Abstract: InGaAsN and GaAsN epitaxial layers with similar
nitrogen compositions in a sample were successfully grown on a
GaAs (001) substrate by solid source molecular beam epitaxy. An
electron cyclotron resonance nitrogen plasma source has been used to
generate atomic nitrogen during the growth of the nitride layers. The
indium composition changed from sample to sample to give
compressive and tensile strained InGaAsN layers. Layer
characteristics have been assessed by high-resolution x-ray
diffraction to determine the relationship between the lattice constant
of the GaAs1-yNy layer and the fraction x of In. The objective was to
determine the In fraction x in an InxGa1-xAs1-yNy epitaxial layer which
exactly cancels the strain present in a GaAs1-yNy epitaxial layer with
the same nitrogen content when grown on a GaAs substrate.
Abstract: Classification is an important topic in machine learning
and bioinformatics. Many datasets have been introduced for
classification tasks. A dataset contains multiple features, and the quality of features influences the classification accuracy of the dataset.
The power of classification for each feature differs. In this study, we
suggest the Classification Influence Index (CII) as an indicator of classification power for each feature. CII enables evaluation of the
features in a dataset and improved classification accuracy by transformation of the dataset. By conducting experiments using CII
and the k-nearest neighbor classifier to analyze real datasets, we confirmed that the proposed index provided meaningful improvement
of the classification accuracy.
Abstract: Malay Folk Literature in early childhood education
served as an important agent in child development that involved
emotional, thinking and language aspects. Up to this moment not
much research has been carried out in Malaysia particularly in the
teaching and learning aspects nor has there been an effort to publish
“big books." Hence this article will discuss the stance taken by
university undergraduate students, teachers and parents in evaluating
Malay Folk Literature in early childhood education to be used as big
books. The data collated and analyzed were taken from 646
respondents comprising 347 undergraduates and 299 teachers. Results
of the study indicated that Malay Folk Literature can be absorbed into
teaching and learning for early childhood with a mean of 4.25 while it
can be in big books with a mean of 4.14. Meanwhile the highest mean
value required for placing Malay Folk Literature genre as big books in
early childhood education rests on exemplary stories for
undergraduates with mean of 4.47; animal fables for teachers with a
mean of 4.38. The lowest mean value of 3.57 is given to lipurlara
stories. The most popular Malay Folk Literature found suitable for
early children is Sang Kancil and the Crocodile, followed by Bawang
Putih Bawang Merah. Pak Padir, Legends of Mahsuri, Origin of
Malacca, and Origin of Rainbow are among the popular stories as
well. Overall the undergraduates show a positive attitude toward all
the items compared to teachers. The t-test analysis has revealed a non
significant relationship between the undergraduate students and
teachers with all the items for the teaching and learning of Malay Folk
Literature.
Abstract: A novel idea presented in this paper is to combine
multihop routing with single-frequency networks (SFNs) for a
broadcasting scenario. An SFN is a set of multiple nodes that transmit
the same data simultaneously, resulting in transmitter macrodiversity.
Two of the most important performance factors of multihop
networks, node reachability and routing robustness, are analyzed.
Simulation results show that our proposed SFN-D routing algorithm
improves the node reachability by 37 percentage points as compared
to non-SFN multihop routing. It shows a diversity gain of 3.7 dB,
meaning that 3.7 dB lower transmission powers are required for the
same reachability. Even better results are possible for larger
networks. If an important node becomes inactive, this algorithm can
find new routes that a non-SFN scheme would not be able to find.
Thus, two of the major problems in multihopping are addressed;
achieving robust routing as well as improving node reachability or
reducing transmission power.
Abstract: Recently, lots of researchers are attracted to retrieving
multimedia database by using some impression words and their values.
Ikezoe-s research is one of the representatives and uses eight pairs of
opposite impression words. We had modified its retrieval interface and
proposed '2D-RIB' in the previous work. The aim of the present paper
is to improve his/her satisfaction level to the retrieval result in the
2D-RIB. Our method is to extend the 2D-RIB. One of our extensions is
to define and introduce the following two measures: 'melody
goodness' and 'general acceptance'. Another extension is three types
of customization menus. The result of evaluation using a pilot system
is as follows. Both of these two measures 'melody goodness'
and -general acceptance- can contribute to the improvement.
Moreover, it is effective if we introduce the customization menu
which enables a retrieval person to reduce the strictness level of
retrieval condition in an impression pair based on his/her need.
Abstract: In this paper sensitivity analysis is performed for
reliability evaluation of power systems. When examining the
reliability of a system, it is useful to recognize how results
change as component parameters are varied. This knowledge
helps engineers to understand the impact of poor data, and
gives insight on how reliability can be improved. For these
reasons, a sensitivity analysis can be performed. Finally, a real
network was used for testing the presented method.