Abstract: The aim of this study was to synthesize the single
walled carbon nanotubes (SWCNTs) and determine their hydrogen
storage capacities. SWCNTs were firstly synthesized by chemical
vapor deposition (CVD) of acetylene (C2H2) on a magnesium oxide
(MgO) powder impregnated with an iron nitrate (Fe(NO3)3·9H2O)
solution. The synthesis parameters were selected as: the synthesis
temperature of 800°C, the iron content in the precursor of 5% and the
synthesis time of 30 min. Purification process of SWCNTs was
fulfilled by microwave digestion at three different temperatures (120,
150 and 200 °C), three different acid concentrations (0.5, 1 and 1.5
M) and for three different time intervals (15, 30 and 60 min). Nitric
acid (HNO3) was used in the removal of the metal catalysts. The
hydrogen storage capacities of the purified materials were measured
using volumetric method at the liquid nitrogen temperature and gas
pressure up to 100 bar. The effects of the purification conditions such
as temperature, time and acid concentration on hydrogen adsorption
were investigated.
Abstract: A seismic isolation pad produced by utilizing the scrap
tire rubber which contains interleaved steel reinforcing cords has been
proposed. The steel cords are expected to function similar to the steel
plates used in conventional laminated rubber bearings. The scrap tire
rubber pad (STRP) isolator is intended to be used in low rise
residential buildings of highly seismic areas of the developing
countries. Experimental investigation was conducted on unbonded
STRP isolators, and test results provided useful information including
stiffness, damping values and an eventual instability of the isolation
unit. Finite element analysis (FE analysis) of STRP isolator was
carried out on properly bonded samples. These types of isolators
provide positive incremental force resisting capacity up to shear strain
level of 155%. This paper briefly discusses the force deformation
behavior of bonded STRP isolators including stability of the isolation
unit.
Abstract: In this study, mechanically alloyed Al 2024 powder is
densified by conventional sintering and by equal channel angular
pressing (ECAP) with and without back pressure. The powder was
encapsulated in an aluminium can for consolidation through ECAP.
The properties obtained in the compacts by conventional sintering
route and by ECAP are compared. The effect of conventional
sintering and ECAP on consolidation behaviour of powder,
microstructure, density and hardness is discussed. Room temperature
back pressure aided ECAP results in nearly full denser (97% of its
theoretical density) compact at room temperature. NanoIndentation
technique was used to determine the modulus of the consolidated
compacts.
Abstract: In this paper, 3X3 routing nodes are proposed to
provide speedup and parallel processing capability in Data Vortex
network architectures. The new design not only significantly
improves network throughput and latency, but also eliminates the
need for distributive traffic control mechanism originally embedded
among nodes and the need for nodal buffering. The cost effectiveness
is studied by a comparison study with the previously proposed 2-
input buffered networks, and considerable performance enhancement
can be achieved with similar or lower cost of hardware. Unlike
previous implementation, the network leaves small probability of
contention, therefore, the packet drop rate must be kept low for such
implementation to be feasible and attractive, and it can be achieved
with proper choice of operation conditions.
Abstract: Today-s Voltage Regulator Modules (VRMs) face increasing design challenges as the number of transistors in microprocessors increases per Moore-s Law. These challenges have recently become even more demanding as microprocessors operate at sub voltage range at significantly high current. This paper presents a new multiphase topology with cell configuration for improved performance in low voltage and high current applications. A lab scale hardware prototype of the new topology was design and constructed. Laboratory tests were performed on the proposed converter and compared with a commercially available VRM. Results from the proposed topology exhibit improved performance compared to the commercially available counterpart.
Abstract: The aim of this article is to narrate the utility of novel simulation approach i.e. convolution method to predict blood concentration of drug utilizing dissolution data of salbutamol sulphate microparticulate formulations with different release patterns (1:1, 1:2 and 1:3, drug:polymer). Dissolution apparatus II USP 2007 and 900 ml double distilled water stirrd at 50 rpm was employed for dissolution analysis. From dissolution data, blood drug concentration was determined, and in return predicted blood drug concentration data was used to calculate the pharmacokinetic parameters i.e. Cmax, Tmax, and AUC. Convolution is a good biwaiver technique; however its better utility needs it application in the conditions where biorelevant dissolution media are used.
Abstract: The world is moving rapidly toward the deployment
of information and communication systems. Nowadays, computing
systems with their fast growth are found everywhere and one of the main challenges for these systems is increasing attacks and security threats against them. Thus, capturing, analyzing and verifying security requirements becomes a very important activity in
development process of computing systems, specially in developing
systems such as banking, military and e-business systems. For
developing every system, a process model which includes a process,
methods and tools is chosen. The Rational Unified Process (RUP) is
one of the most popular and complete process models which is used
by developers in recent years. This process model should be extended to be used in developing secure software systems. In this
paper, the Requirement Discipline of RUP is extended to improve RUP for developing secure software systems. These proposed extensions are adding and integrating a number of Activities, Roles,
and Artifacts to RUP in order to capture, document and model threats
and security requirements of system. These extensions introduce a
group of clear and stepwise activities to developers. By following these activities, developers assure that security requirements are
captured and modeled. These models are used in design, implementation and test activitie
Abstract: This paper compares planning results of the electricity and water generation inventory up to year 2030 in the State of
Kuwait. Currently, the generation inventory consists of oil and gas fired technologies only. The planning study considers two main cases. The first case, Reference case, examines a generation inventory based on oil and gas fired generation technologies only.
The second case examines the inclusion of renewables as part of the generation inventory under two scenarios. In the first scenario, Ref-RE, renewable build-out is based on optimum economic performance
of overall generation system. Result shows that the optimum installed
renewable capacity with electric energy generation of 11% . In the second scenario, Ref-RE20, the renewable capacity build-out is
forced to provide 20% of electric energy by 2030. The respective energy systems costs of Reference, Ref-RE and Ref-RE20 case
scenarios reach US dollar 24, 10 and 14 billion annually in 2030.
Abstract: Knowledge capabilities are increasingly important for
the innovative technology enterprises to enhance the business
performance in terms of product competitiveness, innovation and
sales. Recognition of the company capability by auditing allows them
to further pursue advancement, strategic planning and hence gain
competitive advantages. This paper attempts to develop an
Organizations- Knowledge Capabilities Assessment (OKCA) method
to assess the knowledge capabilities of technology companies. The
OKCA is a questionnaire-based assessment tool which has been
developed to uncover the impact of various knowledge capabilities on
different organizational performance. The collected data is then
analyzed to find out the crucial elements for different technological
companies. Based on the results, innovative technology enterprises are
able to recognize the direction for further improvement on business
performance and future development plan. External environmental
factors affecting organization performance can be found through the
further analysis of some selected reference companies.
Abstract: A new generation of manufacturing machines
so-called MIMCA (modular and integrated machine control
architecture) capable of handling much increased complexity in
manufacturing control-systems is presented. Requirement for more
flexible and effective control systems for manufacturing machine
systems is investigated and dimensioned-which highlights a need for
improved means of coordinating and monitoring production
machinery and equipment used to- transport material. The MIMCA
supports simulation based on machine modeling, was conceived by
the authors to address the issues. Essentially MIMCA comprises an
organized unification of selected architectural frameworks and
modeling methods, which include: NISTRCS, UMC and Colored
Timed Petri nets (CTPN). The unification has been achieved; to
support the design and construction of hierarchical and distributed
machine control which realized the concurrent operation of reusable
and distributed machine control components; ability to handle
growing complexity; and support requirements for real- time control
systems. Thus MIMCA enables mapping between 'what a machine
should do' and 'how the machine does it' in a well-defined but
flexible way designed to facilitate reconfiguration of machine
systems.
Abstract: A behavioral model of a second order switchedcapacitor Sigma-Delta modulator is presented. The purpose of this work is the presentation of a behavioral model of a second order switched capacitor ΣΔ modulator considering (Error due to Clock Jitter, Thermal noise Amplifier Noise, Amplifier Slew-Rate, Non linearity of amplifiers, Gain error, Charge Injection, Clock Feedthrough, and Nonlinear on-resistance). A comparison between the use of MOS switches and the use transmission gate switches use is analyzed.
Abstract: The modified Claus process is commonly used in oil
refining and gas processing to recover sulfur and destroy
contaminants formed in upstream processing. A Claus furnace feed
containing a relatively low concentration of H2S may be incapable of
producing a stable flame. Also, incomplete combustion of
hydrocarbons in the feed can lead to deterioration of the catalyst in
the reactors due to soot or carbon deposition. Therefore, special
consideration is necessary to achieve the appropriate overall sulfur
recovery. In this paper, some configurations available to treat lean
acid gas streams are described and the most appropriate ones are
studied to overcome low H2S concentration problems. As a result,
overall sulfur recovery is investigated for feed preheating and hot gas
configurations.
Abstract: An on-line condition monitoring method for transmission line is proposed using electrical circuit theory and IT technology in this paper. It is reasonable that the circuit parameters such as resistance (R), inductance (L), conductance (g) and capacitance (C) of a transmission line expose the electrical conditions and physical state of the line. Those parameters can be calculated from the linear equation composed of voltages and currents measured by synchro-phasor measurement technique at both end of the line. A set of linear voltage drop equations containing four terminal constants (A, B ,C ,D ) are mathematical models of the transmission line circuits. At least two sets of those linear equations are established from different operation condition of the line, they may mathematically yield those circuit parameters of the line. The conditions of line connectivity including state of connecting parts or contacting parts of the switching device may be monitored by resistance variations during operation. The insulation conditions of the line can be monitored by conductance (g) and capacitance(C) measurements. Together with other condition monitoring devices such as partial discharge, sensors and visual sensing device etc.,they may give useful information to monitor out any incipient symptoms of faults. The prototype of hardware system has been developed and tested through laboratory level simulated transmission lines. The test has shown enough evident to put the proposed method to practical uses.
Abstract: Electronic commerce is growing rapidly with on-line
sales already heading for hundreds of billion dollars per year. Due to
the huge amount of money transferred everyday, an increased
security level is required. In this work we present the architecture of
an intelligent speaker verification system, which is able to accurately
verify the registered users of an e-commerce service using only their
voices as an input. According to the proposed architecture, a
transaction-based e-commerce application should be complemented
by a biometric server where customer-s unique set of speech models
(voiceprint) is stored. The verification procedure requests from the
user to pronounce a personalized sequence of digits and after
capturing speech and extracting voice features at the client side are
sent back to the biometric server. The biometric server uses pattern
recognition to decide whether the received features match the stored
voiceprint of the customer who claims to be, and accordingly grants
verification. The proposed architecture can provide e-commerce
applications with a higher degree of certainty regarding the identity
of a customer, and prevent impostors to execute fraudulent
transactions.
Abstract: A lot of recent research have spoken on the relation
between the increase of the homocysteinemia and some kinds of
cancer . For that, our study was based on the research of a possible
relation between the increase of the concentration of this amino-acid
in the plasma and the appearance of the disease of the Acute
Lymphoblastic Leukaemia in a part of Algerian children with Berber
origin in the East of Algeria . The study has done on 47 ill persons
with an average age of (09±06 ) years , with whom the disease has
diagnosed by blood and marrow examination in the hospital of blood
diseases in the CHU of Batna, and on 194 healthy witnesses of the
same age. The two groups were benefited by a dosage of the
concentration of the homocysteine vitamin B9 ,vitamin B12 , and
also of the study of special polymorphisms of indispensable enzymes
in the metabolism of this acid , and that by the use of the method (
Light cycler ) Real time PCR , on the following enzymes : MS (
C2756G ), MSR ( A66G ) ,MTHFR1 ( C677T ) and MTHFR2
(A1298C). The obtained results have revealed that the rate of the
homozygote muted genotype is the less frequent in the two groups ,
and that exist at list one genotype of each enzyme in the ill group and
in which the percentage exceed with remarkable way the same
genotype in the healthy group and we notice specially the muted
genotype GG of -the methionine synthetase-and the form TT of the
enzyme – methyline tetra hydrofolate reductase – We notice the
existence of considerable number of genotypes in the ill group lied
with characteristic increase of this Amino-acid ,and that for the
reduction of the biologic activity of these enzymes which become
inefficient in the transfer of the homocysteine into the methionine
and cause the diminution of the biologic activity of these enzymes
and with consequence the reduction of the percentage of methylic
radicals in the DNA of studied genes and that lead to the increase of
the activity and the capacity of transcription , and it-s so probably
that this last one is one of the factors of this disease especially if we
know that the specific check-up of vitamins is normal and similar in
the two groups , which ovoid the hypothesis of the reduction of
vitamins . We notice also that the heterozygote genotype is the less in
the sick category except the MTHFR2. Wild genotype is more
frequent in the witness group except MSR. Even these results are
partials; they open a new way in the genetic diagnosis of this
malicious disease which allow a precocious diagnosis and the use of
an effective and appropriated treatment in the same time.
Abstract: A macroscopic constitutive equation is developed for a high-density cellulose insulation material with emphasis on the outof- plane stress relaxation behavior. A hypothesis is proposed where the total stress is additively composed by an out-of-plane visco-elastic isotropic contribution and an in-plane elastic orthotropic response. The theory is validated against out-of-plane stress relaxation, compressive experiments and in-plane tensile hysteresis, respectively. For large scale finite element simulations, the presented model provides a balance between simplicity and capturing the materials constitutive behaviour.
Abstract: The effectiveness of consuming a nutrient fortified oat drink on iron, zinc, vitamin A and vitamin C status was assessed among a cohort of school-aged Filipino children. Ultimate study implementation permitted only a within-subject comparison of change in nutritional status after four months of consuming a nutrient fortified oat drink. Thirty-eight anemic children (5-8 years) consumed an oat drink fortified with iron as NaFeEDTA, zinc, vitamin A and vitamin C for 120 days. Height, weight, serum nutrient levels, anemia status and dietary intake were assessed pre and post intervention. Thirty-four anemic children completed the intervention. After 4 months of intervention, prevalence of anemia decreased by 68% and significant improvements in iron and vitamin A status were observed. Results demonstrate the effectiveness of the fortified oat drink in alleviating anemia in young children and highlight the value of fortification programs
Abstract: Analytical investigation of the sedimentation
processes in the river engineering and hydraulic structures is of vital
importance as this can affect water supply for the cultivating lands in
the command area. The reason being that gradual sediment formation
behind the reservoir can reduce the nominal capacity of these dams.
The aim of the present paper is to analytically investigate
sedimentation process along the river course and behind the storage
reservoirs in general and the Eastern Intake of the Dez Diversion weir
in particular using the SHARC software. Results of the model
indicated the water level at 115.97m whereas the real time
measurement from the river cross section was 115.98 m which
suggests a significantly close relation between them. The average
transported sediment load in the river was measured at 0.25mm ,
from which it can be concluded that nearly 100% of the suspended
loads in river are moving which suggests no sediment settling but
indicates that almost all sediment loads enters into the intake. It was
further showed the average sediment diameter entering the intake to
be 0.293 mm which in turn suggests that about 85% of suspended
sediments in the river entre the intake. Comparison of the results
from the SHARC model with those obtained form the SSIIM
software suggests quite similar outputs but distinguishing the
SHARC model as more appropriate for the analysis of simpler
problems than other model.
Abstract: Generation system reliability assessment is an
important task which can be performed using deterministic or
probabilistic techniques. The probabilistic approaches have
significant advantages over the deterministic methods. However,
more complicated modeling is required by the probabilistic
approaches. Power generation model is a basic requirement for this
assessment. One form of the generation models is the well known
capacity outage probability table (COPT). Different analytical
techniques have been used to construct the COPT. These approaches
require considerable mathematical modeling of the generating units.
The unit-s models are combined to build the COPT which will add
more burdens on the process of creating the COPT. Decimal to
Binary Conversion (DBC) technique is widely and commonly applied
in electronic systems and computing This paper proposes a novel
utilization of the DBC to create the COPT without engaging in
analytical modeling or time consuming simulations. The simple
binary representation , “0 " and “1 " is used to model the states o f
generating units. The proposed technique is proven to be an effective
approach to build the generation model.
Abstract: High Power Lasers produce an intense burst of
Bremmstrahlung radiation which has potential applications in broadband
x-ray radiography. Since the radiation produced is through the
interaction of accelerated electrons with the remaining laser target,
these bursts are extremely short – in the region of a few ps. As a
result, the laser-produced x-rays are capable of imaging complex
dynamic objects with zero motion blur.