Abstract: The reduction of phosphorus and sulfur in engine oil
are the main topics of this paper. Very reproducible boundary
lubrication tests were conducted as part of Design of Experiment
software (DOE) to study the behavior of fluorinated catalyst iron
fluoride (FeF3), and polutetrafluoroethylene or Teflon (PTFE) in
developing environmentally friendly (reduced P and S) anti-wear
additives for future engine oil formulations. Multi-component
Chevron fully formulated oil (GF3) and Chevron plain oil were used
with the addition of PTFE and catalyst to characterize and analyze
their performance. Lower phosphorus blends were the goal of the
model solution. Experiments indicated that new sub-micron FeF3
catalyst played an important role in preventing breakdown of the
tribofilm.
Abstract: It is a major challenge to build a bridge superstructure
that has long-term durability and low maintenance requirements. A
solution to this challenge may be to use new materials or to
implement new structural systems. Fiber Reinforced Polymer (FRP)
composites have continued to play an important role in solving some
of persistent problems in infrastructure applications because of its
high specific strength, light weight, and durability. In this study, the
concept of the hybrid FRP-concrete structural systems is applied to a
bridge superstructure. The hybrid FRP-concrete bridge superstructure
is intended to have durable, structurally sound, and cost effective
hybrid system that will take full advantage of the inherent properties
of both FRP materials and concrete. In this study, two hybrid FRP-concrete
bridge systems were investigated. The first system consists
of trapezoidal cell units forming a bridge superstructure. The second
one is formed by arch cells. The two systems rely on using cellular
components to form the core of the bridge superstructure, and an
outer shell to warp around those cells to form the integral unit of the
bridge. Both systems were investigated analytically by using finite
element (FE) analysis. From the rigorous FE studies, it was
concluded that first system is more efficient than the second.
Abstract: Effect of sprue/metal head height on mould filling,
microstructure and mechanical properties of TWDI casting is studied.
Results show that metal/sprue height of 50 mm is not sufficient to
push the melt through the gating channel, but as it is increased from
100-350 mm, proper mould filling is achieved. However at higher
heights between 200 mm and 350 mm, defects associated with
incomplete solidification, carbide precipitation and turbulent flow are
evident. This research shows that superior UTS, hardness, nodularity
and nodule count are obtained at 100 mm sprue height.
Abstract: Si ion implantation was widely used to synthesize
specimens of SiO2 containing supersaturated Si and subsequent high
temperature annealing induces the formation of embedded
luminescent Si nanocrystals. In this work, the potentialities of excimer
UV-light (172 nm, 7.2 eV) irradiation and rapid thermal annealing
(RTA) to enhance the photoluminescence and to achieve low
temperature formation of Si nanocrystals have been investigated. The
Si ions were introduced at acceleration energy of 180 keV to fluence of
7.5 x 1016 ions/cm2. The implanted samples were subsequently
irradiated with an excimer-UV lamp. After the process, the samples
were rapidly thermal annealed before furnace annealing (FA).
Photoluminescence spectra were measured at various stages at the
process. We found that the luminescence intensity is strongly
enhanced with excimer-UV irradiation and RTA. Moreover, effective
visible photoluminescence is found to be observed even after FA at
900 oC, only for specimens treated with excimer-UV lamp and RTA.
We also prepared specimens of Si nanocrystals embedded in a SiO2 by
reactive pulsed laser deposition (PLD) in an oxygen atmosphere. We
will make clear the similarities and differences with the way of
preparation.
Abstract: Based on Business and Consumer Survey (BCS) data,
the European Commission (EC) regularly publishes the monthly
Economic Sentiment Indicator (ESI) for each EU member state. ESI
is conceptualized as a leading indicator, aimed ad tracking the overall
economic activity. In calculating ESI, the EC employs arbitrarily
chosen weights on 15 BCS response balances. This paper raises the
predictive quality of ESI by applying nonlinear programming to find
such weights that maximize the correlation coefficient of ESI and
year-on-year GDP growth. The obtained results show that the highest
weights are assigned to the response balances of industrial sector
questions, followed by questions from the retail trade sector. This
comes as no surprise since the existing literature shows that the
industrial production is a plausible proxy for the overall Croatian
economic activity and since Croatian GDP is largely influenced by
the aggregate personal consumption.
Abstract: Food poisoning and infection by bacteria are of public
health significance to both developing and developed countries.
Samples of ogi (akamu) prepared from white and yellow variety of
maize sold in Uturu and Okigwe were analyzed together with the
laboratory prepared ogi for bacterial quality using the standard
microbiological methods. The analyses showed that both white and
yellow variety had total bacterial counts (cfu/g) of 4.0 ×107 and 3.9 x
107 for the laboratory prepared ogi while the commercial ogi had 5.2
x 107 and 4.9 x107, 4.9 x107 and 4.5 x107, 5.4 x107 and 5.0 x107 for
Eke-Okigwe, Up-gate and Nkwo-Achara market respectively. The
Staphylococcal counts ranged from 2.0 x 102 to 5.0 x102 and 1.0 x
102 to 4.0 x102 for the white and yellow variety from the different
markets while Staphylococcal growth was not recorded on the
laboratory prepared ogi. The laboratory prepared ogi had no Coliform
growth while the commercially prepared ogi had counts of 0.5 x103
to 1.6 x 103 for white variety and 0.3 x 103 to 1.1 x103 for yellow
variety respectively. The Lactic acid bacterial count of 3.5x106 and
3.0x106 was recorded for the laboratory ogi while the commercially
prepared ogi ranged from 3.2x106 to 4.2x106 (white variety) and 3.0
x106 to 3.9 x106 (yellow). The presence of bacteria isolates from the
commercial and laboratory fermented ogi showed that Lactobacillus
sp, Leuconostoc sp and Citrobacter sp were present in all the
samples, Micrococcus sp and Klebsiella sp were isolated from Eke-
Okigwe and ABSU-up-gate markets varieties respectively, E. coli
and Staphylococcus sp were present in Eke-Okigwe and Nkwo-
Achara markets while Salmonella sp were isolated from the three
markets. Hence, there are chances of contracting food borne diseases
from commercially prepared ogi. Therefore, there is the need for
sanitary measures in the production of fermented cereals so as to
minimize the rate of food borne pathogens during processing and
storage.
Abstract: Psyllium gum alone and in combination with
sunflower oil was investigated as a possible alternative edible coating
for improvement of quality and shelf life of fresh-cut papaya.
Different concentrations including 0.5, 1 and 1.5 percent of psyllium
gum were used for coating of fresh-cut papaya. In some samples,
refined sunflower oil was used as a lipid component to increase the
effectiveness of coating in terms of water barrier properties. Soya
lecithin was used as an emulsifier in coatings containing oil.
Pretreatment with 1% calcium chloride was given to maintain the
firmness of fresh-cut papaya cubes. 1% psyllium gum coating was
found to yield better results. Further, addition of oil helped to
maintain the quality and acted as a barrier to water vapour, therefore,
minimizing the weight loss.
Abstract: In this study, the feasibility of incorporating ceramic
waste from bricks (perforated brick and double hollow brick) and
extruded polystyrene (XPS) waste, is analysed.
Results show that it is possible to incorporate up to 25% of
ceramic waste and 4% of XPS waste over the weight of gypsum in a
gypsum matrix. Furthermore, with the addition of ceramic waste an
8% of surface hardness increase and a 25% of capillary water
absorption reduction can be obtained. On the other hand, with the
addition of XPS, a 26% reduction of density and a 37% improvement
of thermal conductivity can be obtained.
The obtained results are favorable to use these materials in order to
produce prefabricated gypsum and also as material for interior
cladding walls.
Abstract: Several parameters are established in order to measure
biodiesel quality. One of them is the iodine value, which is an
important parameter that measures the total unsaturation within a
mixture of fatty acids. Limitation of unsaturated fatty acids is
necessary since warming of higher quantity of these ones ends in
either formation of deposits inside the motor or damage of lubricant.
Determination of iodine value by official procedure tends to be very
laborious, with high costs and toxicity of the reagents, this study uses
artificial neural network (ANN) in order to predict the iodine value
property as an alternative to these problems. The methodology of
development of networks used 13 esters of fatty acids in the input
with convergence algorithms of back propagation of back
propagation type were optimized in order to get an architecture of
prediction of iodine value. This study allowed us to demonstrate the
neural networks’ ability to learn the correlation between biodiesel
quality properties, in this caseiodine value, and the molecular
structures that make it up. The model developed in the study reached
a correlation coefficient (R) of 0.99 for both network validation and
network simulation, with Levenberg-Maquardt algorithm.
Abstract: A comparison of activity and stability of the as-formed
Pt/C, Pt-Co and Pt-Pd/C electrocatalysts, prepared by a combined
approach of impregnation and seeding, was performed. According to
the activity test in a single Proton Exchange Membrane (PEM) fuel
cell, the Oxygen Reduction Reaction (ORR) activity of the Pt-M/C
electrocatalyst was slightly lower than that of Pt/C. The j0.9 V and
E10 mA/cm2 of the as-prepared electrocatalysts increased in the order of
Pt/C > Pt-Co/C > Pt-Pd/C. However, in the medium-to-high current
density region, Pt-Pd/C exhibited the best performance. With regard to
their stability in a 0.5 M H2SO4 electrolyte solution, the
electrochemical surface area decreased as the number of rounds of
repetitive potential cycling increased due to the dissolution of the
metals within the catalyst structure. For long-term measurement, Pt-
Pd/C was the most stable than the other three electrocatalysts.
Abstract: This work studies the effect of chemical composition
on the activity and selectivity of γ–alumina supported CuO/
MnO2/Cr2O3 catalysts toward deep oxidation of CO, dimethyl ether
(DME) and methanol. The catalysts were prepared by impregnation
of the support with an aqueous solution of copper nitrate, manganese
nitrate and CrO3 under different conditions. Thermal, XRD and TPR
analysis were performed. The catalytic measurements of single
compounds oxidation were carried out on continuous flow equipment
with a four-channel isothermal stainless steel reactor. Flow-line
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions that mimic closely the industrial
ones was used. The reactant and product gases were analyzed by
means of on-line gas chromatographs.
On the basis of XRD analysis it can be concluded that the active
component of the mixed Cu-Mn-Cr/γ–alumina catalysts consists of at
least six compounds – CuO, Cr2O3, MnO2, Cu1.5Mn1.5O4,
Cu1.5Cr1.5O4 and CuCr2O4, depending on the Cu/Mn/Cr molar ratio.
Chemical composition strongly influences catalytic properties, this
influence being quite variable with regards to the different processes.
The rate of CO oxidation rapidly decrease with increasing of
chromium content in the active component while for the DME was
observed the reverse trend. It was concluded that the best
compromise are the catalysts with Cu/(Mn + Cr) molar ratio 1:5 and
Mn/Cr molar ratio from 1:3 to 1:4.
Abstract: This paper aims to study the effect of cold work
condition on the microstructure of Cu-1.5wt%Ti, and Cu-3.5wt%Ti
and hence mechanical properties. The samples under investigation
were machined, and solution heat treated. X-ray diffraction technique
is used to identify the different phases present after cold deformation
by compression and also different heat treatment and also measuring
the relative quantities of phases present. The metallographic
examination is used to study the microstructure of the samples. The
hardness measurements were used to indicate the change in
mechanical properties. The results are compared with the mechanical
properties obtained by previous workers. Experiments on cold
compression followed by aging of Cu-Ti alloys have indicated that
the most efficient hardening of the material results from continuous
precipitation of very fine particles within the matrix. These particles
were reported to be β`-type, Cu4Ti phase. The β`-β transformation
and particles coarsening within the matrix as well as long grain
boundaries were responsible for the overaging of Cu-1.5wt%Ti and
Cu-3.5wt%Ti alloys. It is well known that plate-like particles are β –
type, Cu3Ti phase. Discontinuous precipitation was found to start at
the grain boundaries and expand into grain interior. At the higher
aging temperature, a classic Widmanstätten morphology forms giving
rise to a coarse microstructure comprised of α and the equilibrium
phase β. Those results were confirmed by X-ray analysis, which
found that a few percent of Cu3Ti, β precipitates are formed during
aging at high temperature for long time for both Cu- Ti alloys (i.e.
Cu-1.5wt%Ti and Cu-3.5wt%Ti).
Abstract: Cloud computing has emerged as a promising
direction for cost efficient and reliable service delivery across data
communication networks. The dynamic location of service facilities
and the virtualization of hardware and software elements are stressing
the communication networks and protocols, especially when data
centres are interconnected through the internet. Although the
computing aspects of cloud technologies have been largely
investigated, lower attention has been devoted to the networking
services without involving IT operating overhead. Cloud computing
has enabled elastic and transparent access to infrastructure services
without involving IT operating overhead. Virtualization has been a
key enabler for cloud computing. While resource virtualization and
service abstraction have been widely investigated, networking in
cloud remains a difficult puzzle. Even though network has significant
role in facilitating hybrid cloud scenarios, it hasn't received much
attention in research community until recently. We propose Network
as a Service (NaaS), which forms the basis of unifying public and
private clouds. In this paper, we identify various challenges in
adoption of hybrid cloud. We discuss the design and implementation
of a cloud platform.
Abstract: Amoxicillin is an antibiotic which is widely used to
treat various infections in both human beings and animals. However,
when amoxicillin is released into the environment, it is a major
problem. Amoxicillin causes bacterial resistance to these drugs and
failure of treatment with antibiotics. Liquid membrane is of great
interest as a promising method for the separation and recovery of the
target ions from aqueous solutions due to the use of carriers for the
transport mechanism, resulting in highly selectivity and rapid
transportation of the desired metal ions. The simultaneous processes
of extraction and stripping in a single unit operation of liquid
membrane system are very interesting. Therefore, it is practical to
apply liquid membrane, particularly the HFSLM for industrial
applications as HFSLM is proved to be a separation process with
lower capital and operating costs, low energy and extractant with
long life time, high selectivity and high fluxes compared with solid
membranes. It is a simple design amenable to scaling up for industrial
applications. The extraction and recovery for (Amoxicillin) through
the hollow fiber supported liquid membrane (HFSLM) using
aliquat336 as a carrier were explored with the experimental data. The
important variables affecting on transport of amoxicillin viz.
extractant concentration and operating time were investigated. The
highest AMOX- extraction percentages of 85.35 and Amoxicillin
stripping of 80.04 were achieved with the best condition at 6 mmol/L
[aliquat336] and operating time 100 min. The extraction reaction
order (n) and the extraction reaction rate constant (kf) were found to
be 1.00 and 0.0344 min-1, respectively.
Abstract: In this paper, the cable model of dendrites have been
considered. The dendrites are cylindrical cables of various segments
having variable length and reducing radius from start point at synapse
and end points. For a particular event signal being received by a
neuron in response only some dendrite are active at a particular
instance. Initial current signals with different current flows in
dendrite are assumed. Due to overlapping and coupling of active
dendrite, they induce currents in the dendrite segments of each other
at a particular instance. But how these currents are induced in the
various segments of active dendrites due to coupling between these
dendrites, It is not presented in the literature. Here the paper presents
a model for induced currents in active dendrite segments due to
mutual coupling at the starting instance of an activity in dendrite. The
model is as discussed further.
Abstract: The effect of processing on plasma lipid profile and
atherogenic indices of rats fed Artocarpus heterophyllus seed diets at
different concentrations were investigated. Fifty five rats were used
for this study, they were divided into eleven groups of five rats each
(one control group and ten test groups), the test groups were fed raw,
boiled, roasted, fermented and soaked diets at 10% and 40%
concentrations. The study lasted for thirty five days. The diets led to
significant decrease (p
Abstract: This paper presents a rheological model for producing
shape-memory thermoplastic polymers. Shape-memory occurs as a
result of internal rearrangement of the structural elements of a
polymer. A non-linear viscoelastic model was developed that allows
qualitative and quantitative prediction of the stress-strain behavior of
shape-memory polymers during heating. This research was done to
develop a technique to determine the maximum possible change in
size of shape-memory products during heating. The rheological
model used in this work was particularly suitable for defining process
parameters and constructive parameters of the processing equipment.
Abstract: Mustard leaves are rich in folates, vitamin A, K and
B-complex. Mustard greens are low in calories and fats and rich in
dietary fiber. They are rich in potassium, manganese, iron, copper,
calcium, magnesium and low in sodium. It is very rich in antioxidants
and Phytonutrients. For the optimization of process variables
(moisture content and mustard leave powder), the experiments were
conducted according to central composite Face Centered Composite
design of RSM. The mustard leaves powder was replaced with
composite flour (a combination of rice, chickpea and corn in the ratio
of 70:15:15). The extrudate was extruded in a twin screw extruder at
a barrel temperature of 120°C. The independent variables were
mustard leaves powder (2-10 %) and moisture content (12-20 %).
Responses analyzed were bulk density, water solubility index, water
absorption index, lateral expansion, antioxidant activity, total
phenolic content, and overall acceptability. The optimum conditions
obtained were 7.19 g mustard leaves powder in 100g premix having
16.8% moisture content (w.b).
Abstract: This paper presents Carrier Sense Multiple Access
(CSMA) communication models based on SoC design methodology.
Such a model can be used to support the modeling of the complex
wireless communication systems. Therefore, the use of such
communication model is an important technique in the construction
of high-performance communication. SystemC has been chosen
because it provides a homogeneous design flow for complex designs
(i.e. SoC and IP-based design). We use a swarm system to validate
CSMA designed model and to show how advantages of incorporating
communication early in the design process. The wireless
communication created through the modeling of CSMA protocol that
can be used to achieve communication between all the agents and to
coordinate access to the shared medium (channel).
Abstract: The Chair of Thermal Engineering at Poznan
University of Technology has been conducted research works on the
possibilities of using carbon nanostructures in energy and mechanics
applications for a couple of years. Those studies have provided results in a form of co-operation with foreign research centres, numerous publications and patent
applications.
Authors of this paper have studied the influence of multi-walled
carbon nanostructures on changes in static friction arising when steel
surfaces were moved. Tests were made using the original test stand
consisting of automatically controlled inclined plane driven by
precise stepper motors. Computer program created in the LabView
environment was responsible for monitoring of the stand operation,
accuracy of measurements and archiving the obtained results. Such a
solution enabled to obtain high accuracy and repeatability of all
conducted experiments.
Tests and analysis of the obtained results allowed us to determine
how additional layers of carbon nanostructures influenced on changes
of static friction coefficients. At the same time, we analyzed the
potential possibilities of applying nanostructures under consideration
in mechanics.