Abstract: Remote arid areas of the vast expanses of the African
deserts hold huge subterranean reserves of brackish water resources
waiting for economic development. This work presents design
guidelines as well as initial performance data of new autonomous
solar desalination equipment which could help local communities
produce their own fresh water using solar energy only and, why not,
contribute to transforming desert lands into lush gardens. The output
of solar distillation equipments are typically low and in the range of 3
l/m2/day on the average. This new design with an integrated, water
based, environmentally-friendly solar heat storage system produced 5
l/m2/day in early spring weather. Equipment output during summer
exceeded 9 liters per m2 per day.
Abstract: Mobil Producing Nigeria Unlimited (MPNU), a
subsidiary of ExxonMobil and the highest crude oil & condensate
producer in Nigeria has its operational base and an oil terminal, the
Qua Iboe terminal (QIT) located at Ibeno, Nigeria. Other oil
companies like Network Exploration and Production Nigeria Ltd,
Frontier Oil Ltd; Shell Petroleum Development Company Ltd; Elf
Petroleum Nigeria Ltd and Nigerian Agip Energy, a subsidiary of the
Italian ENI E&P operate onshore, on the continental shelf and in deep
offshore of the Atlantic Ocean, respectively with the coastal waters of
Ibeno, Nigeria as the nearest shoreline. This study was designed to
delineate the oil-polluted sites in Ibeno, Nigeria using
microbiological and physico-chemical characterization of soils,
sediments and ground and surface water samples from the study area.
Results obtained revealed that there have been significant recent
hydrocarbon inputs into this environment as observed from the high
counts of hydrocarbonoclastic microorganisms in excess of 1% at all
the stations sampled. Moreover, high concentrations of THC, BTEX
and heavy metals contents in all the samples analyzed corroborate the
high recent crude oil input into the study area. The results also
showed that the pollution of the different environmental media
sampled were of varying degrees, following the trend: ground water
> surface water > sediments > soils.
Abstract: This paper presents an application of Artificial Neural
Network (ANN) algorithm for improving power system voltage
stability. The training data is obtained by solving several normal and
abnormal conditions using the Linear Programming technique. The
selected objective function gives minimum deviation of the reactive
power control variables, which leads to the maximization of
minimum Eigen value of load flow Jacobian. The considered reactive
power control variables are switchable VAR compensators, OLTC
transformers and excitation of generators. The method has been
implemented on a modified IEEE 30-bus test system. The results
obtain from the test clearly show that the trained neural network is
capable of improving the voltage stability in power system with a
high level of precision and speed.
Abstract: In this paper, the actuality of the study, and the role of
subjective well-being problem in modern psychology and the
comprehending of subjective well-being by current students is
defined. The purpose of this research is to educe peculiarities of
comprehending of subjective well-being by students with various
levels of emotional intelligence. Methods of research are adapted
Russian-Language questionnaire of K. Riff 'The scales of
psychological well-being'; emotional intelligence questionnaire of D.
V. Lusin. The research involved 72 students from different
universities and disciplines aged between 18 and 24. Analyzing the
results of the studies, it can be concluded that the understanding of
happiness in different groups of students with high and low levels of
overall emotional intelligence is different, as well as differentiated by
gender. Students with a higher level of happiness possess more
capacity and higher need to control their emotions, to cause and
maintain the desired emotions and control something undesirable.
Abstract: It is an established fact that polymers have several
physical limitations such as low stiffness and low resistance to
impact on loading. Hence, polymers do not usually have requisite
mechanical strength for application in various fields. The
reinforcement by high strength fibers provides the polymer
substantially enhanced mechanical properties and makes them more
suitable for a large number of diverse applications. This research
evaluates the effects of particulate Cow bone and Groundnut shell
additions on the mechanical properties and microstructure of cow
bone and groundnut shell reinforced epoxy composite in order to
assess the possibility of using it as a material for engineering
applications. Cow bone and groundnut shell particles reinforced with
epoxy (CBRPC and GSRPC) was prepared by varying the cow bone
and groundnut shell particles from 0-25 wt% with 5 wt% intervals. A
Hybrid of the Cow bone and Groundnut shell (HGSCB) reinforce
with epoxy was also prepared. The mechanical properties of the
developed composites were investigated. Optical microscopy was
used to examine the microstructure of the composites. The results
revealed that mechanical properties did not increase uniformly with
additions in filler but exhibited maximum properties at specific
percentages of filler additions. From the Microscopic evaluation, it
was discovered that homogeneity decreases with increase in % filler,
this could be due to poor interfacial bonding.
Abstract: In recent years, multi-antenna techniques are being considered as a potential solution to increase the flow of future wireless communication systems. The objective of this article is to study the emission and reception system MIMO (Multiple Input Multiple Output), and present the different reception decoding techniques. First we will present the least complex technical, linear receivers such as the zero forcing equalizer (ZF) and minimum mean squared error (MMSE). Then a nonlinear technique called ordered successive cancellation of interferences (OSIC) and the optimal detector based on the maximum likelihood criterion (ML), finally, we simulate the associated decoding algorithms for MIMO system such as ZF, MMSE, OSIC and ML, thus a comparison of performance of these algorithms in MIMO context.
Abstract: Rice bran is normally used as a raw material for rice
bran oil production or sold as feed with a low price. Conventionally,
the protein in defatted rice bran was extracted using alkaline
extraction and acid precipitation, which involves in chemical usage
and lowering some nutritious component. This study was conducted
in order to extract of rice bran protein concentrate (RBPC) from
defatted rice bran using enzymes and employing polysaccharides in a
precipitating step. The properties of RBPC obtained will be compared
to those of a control sample extracted using a conventional method.
The results showed that extraction of protein from rice bran using
enzymes exhibited the higher protein recovery compared to that
extraction with alkaline. The extraction conditions using alcalase 2%
(v/w) at 50 C, pH 9.5 gave the highest protein (2.44%) and yield
(32.09%) in extracted solution compared to other enzymes. Rice bran
protein concentrate powder prepared by a precipitation step using
alginate (protein in solution: alginate 1:0.016) exhibited the highest
protein (27.55%) and yield (6.84%). Precipitation using alginate was
better than that of acid. RBPC extracted with alkaline (ALK) or
enzyme alcalase (ALC), then precipitated with alginate (AL)
(samples RBP-ALK-AL and RBP-ALC-AL) yielded the precipitation
rate of 75% and 91.30%, respectively. Therefore, protein
precipitation using alginate was then selected. Amino acid profile of
control sample, and sample precipitated with alginate, as compared to
casein and soy protein isolated, showed that control sample showed
the highest content among all sample. Functional property study of
RBP showed that the highest nitrogen solubility occurred in pH 8-10.
There was no statically significant between emulsion capacity and
emulsion stability of control and sample precipitated by alginate.
However, control sample showed a higher of foaming capacity and
foaming stability compared to those of sample precipitated with
alginate. The finding was successful in terms of minimizing
chemicals used in extraction and precipitation steps in preparation of
rice bran protein concentrate. This research involves in a production
of value-added product in which the double amount of protein (28%)
compared to original amount (14%) contained in rice bran could be
beneficial in terms of adding to food products e.g. healthy drink with
high protein and fiber. In addition, the basic knowledge of functional
property of rice bran protein concentrate was obtained, which can be
used to appropriately select the application of this value-added
product from rice bran.
Abstract: Fibre cement plates, often used in construction,
generally are made using quartz as an inert material, cement as a
binder and cellulose as a fibre. This paper, first of all, investigates the
mechanical properties and durability of fibre cement plates when
quartz is both partly and fully replaced with diatomite. Diatomite
does not only have lower density compared to quartz but also has
high pozzolanic activity. The main objective of this paper is the
investigation of the effects of supplementary cementing materials
(SCMs) on the short and long term mechanical properties and
durability characteristics of fibre cement plates prepared using
diatomite. Supplementary cementing materials such as ground
granulated blast furnace slug (GGBS) and fly ash (FA) are used in
this study. Volume proportions of 10, 20, 30 and 40% of GGBS and
FA are used as partial replacement materials to cement. Short and
long term mechanical properties such as compressive and flexural
strengths as well as sorptivity characteristics and mass were
investigated. Consistency and setting time at each replacement levels
of SCMs were also recorded. The effects of using supplementary
cementing materials on the carbonation and sulphate resistance of
fibre cement plates were then experimented. The results, first of all,
show that the use of diatomite as a full or partial replacement to
quartz resulted in a systematic decrease in total mass of the fibre
cement plates. The reduction of mass was largely due to the lower
density and finer particle size of diatomite compared to quartz. The
use of diatomite did not only reduce the mass of these plates but also
increased the compressive strength significantly as a result of its high
pozzolanic activity. The replacement levels of both GGBS and FA
resulted in a systematic decrease in short term compressive strength
with increasing replacement levels. This was essentially expected as
the total rate of hydration is much lower in GGBS and FA than that
of cement. Long term results however, indicated that the compressive
strength of fibre cement plates prepared using both GGBS and FA
increases with time and hence the compressive strength of plates
prepared using SCMs is either equivalent or more than the
compressive strength of plates prepared using cement alone.
Durability characteristics of fibre cement plates prepared using SCMs
were enhanced significantly. Measurements of sopritivty
characteristics were also indicated that the plates prepared using
SCMs has much lower water absorption capacities compared to
plates prepared cement alone. Much higher resistance to carbonation
and sulphate attach were observed with plates prepared using SCMs.
The results presented in this paper show that the use of SCMs does
not only support the production of more sustainable construction
materials but also enhances the mechanical properties and durability
characteristics of fibre cement plates.
Abstract: Continuous upflow filters can combine the nutrient
(nitrogen and phosphate) and suspended solid removal in one unit
process. The contaminant removal could be achieved chemically or
biologically; in both processes the filter removal efficiency depends
on the interaction between the packed filter media and the influent. In
this paper a residence time distribution (RTD) study was carried out
to understand and compare the transfer behaviour of contaminants
through a selected filter media packed in a laboratory-scale
continuous up flow filter; the selected filter media are limestone and
white dolomite. The experimental work was conducted by injecting a
tracer (red drain dye tracer –RDD) into the filtration system and then
measuring the tracer concentration at the outflow as a function of
time; the tracer injection was applied at hydraulic loading rates
(HLRs) (3.8 to 15.2 m h-1). The results were analysed according to
the cumulative distribution function F(t) to estimate the residence
time of the tracer molecules inside the filter media. The mean
residence time (MRT) and variance σ2 are two moments of RTD that
were calculated to compare the RTD characteristics of limestone with
white dolomite. The results showed that the exit-age distribution of
the tracer looks better at HLRs (3.8 to 7.6 m h-1) and (3.8 m h-1) for
limestone and white dolomite respectively. At these HLRs the
cumulative distribution function F(t) revealed that the residence time
of the tracer inside the limestone was longer than in the white
dolomite; whereas all the tracer took 8 minutes to leave the white
dolomite at 3.8 m h-1. On the other hand, the same amount of the
tracer took 10 minutes to leave the limestone at the same HLR. In
conclusion, the determination of the optimal level of hydraulic
loading rate, which achieved the better influent distribution over the
filtration system, helps to identify the applicability of the material as
filter media. Further work will be applied to examine the efficiency
of the limestone and white dolomite for phosphate removal by
pumping a phosphate solution into the filter at HLRs (3.8 to 7.6 m h-1).
Abstract: The sea waves carry thousands of GWs of power
globally. Although there are a number of different approaches to
harness offshore energy, they are likely to be expensive, practically
challenging, and vulnerable to storms. Therefore, this paper considers
using the near shore waves for generating mechanical and electrical
power. It introduces two new approaches, the wave manipulation and
using a variable duct turbine, for intercepting very wide wave fronts
and coping with the fluctuations of the wave height and the sea level,
respectively. The first approach effectively allows capturing much
more energy yet with a much narrower turbine rotor. The second
approach allows using a rotor with a smaller radius but captures
energy of higher wave fronts at higher sea levels yet preventing it
from totally submerging. To illustrate the effectiveness of the first
approach, the paper contains a description and the simulation results
of a scale model of a wave manipulator. Then, it includes the results
of testing a physical model of the manipulator and a single duct, axial
flow turbine in a wave flume in the laboratory. The paper also
includes comparisons of theoretical predictions, simulation results,
and wave flume tests with respect to the incident energy, loss in wave
manipulation, minimal loss, brake torque, and the angular velocity.
Abstract: Background in music analysis: Traditionally, when we
think about a composer’s sketches, the chances are that we are
thinking in terms of the working out of detail, rather than the
evolution of an overall concept. Since music is a “time art,” it follows
that questions of a form cannot be entirely detached from
considerations of time. One could say that composers tend to regard
time either as a place gradually and partially intuitively filled, or they
can look for a specific strategy to occupy it. It seems that the one
thing that sheds light on Stockhausen’s compositional thinking is his
frequent use of “form schemas,” that is often a single-page
representation of the entire structure of a piece.
Background in music technology: Sonic Visualiser is a program
used to study a musical recording. It is an open source application for
viewing, analyzing, and annotating music audio files. It contains a
number of visualisation tools, which are designed with useful default
parameters for musical analysis. Additionally, the Vamp plugin
format of SV supports to provide analysis such as for example
structural segmentation.
Aims: The aim of paper is to show how SV may be used to obtain
a better understanding of the specific musical work, and how the
compositional strategy does impact on musical structures and musical
surfaces. It is known that “traditional” music analytic methods don’t
allow indicating interrelationships between musical surface (which is
perceived) and underlying musical/acoustical structure.
Main Contribution: Stockhausen had dealt with the most diverse
musical problems by the most varied methods. A characteristic which
he had never ceased to be placed at the center of his thought and
works, it was the quest for a new balance founded upon an acute
connection between speculation and intuition. In the case with
Mikrophonie I (1964) for tam-tam and 6 players Stockhausen makes
a distinction between the “connection scheme,” which indicates the
ground rules underlying all versions, and the form scheme, which is
associated with a particular version. The preface to the published
score includes both the connection scheme, and a single instance of a
“form scheme,” which is what one can hear on the CD recording. In
the current study, the insight into the compositional strategy chosen
by Stockhausen was been compared with auditory image, that is, with
the perceived musical surface. Stockhausen’s musical work is
analyzed both in terms of melodic/voice and timbre evolution.
Implications: The current study shows how musical structures
have determined of musical surface. The general assumption is this,
that while listening to music we can extract basic kinds of musical
information from musical surfaces. It is shown that interactive
strategies of musical structure analysis can offer a very fruitful way
of looking directly into certain structural features of music.
Abstract: This paper presents development results of usage of
C-OTDR monitoring systems for rail traffic management. The COTDR
method is based on vibrosensitive properties of optical fibers.
Analysis of Rayleigh backscattering radiation parameters changes
which take place due to microscopic seismoacoustic impacts on the
optical fiber allows to determine seismoacoustic emission source
positions and to identify their types. This approach proved successful
for rail traffic management (moving block system, weigh- in-motion
system etc.).
Abstract: Due to today’s globalization as well as outsourcing
practices of the companies, the Supply Chain (SC) performances
have become more dependent on the efficient movement of material
among places that are geographically dispersed, where there is more
chance for disruptions. One such disruption is the quality and
delivery uncertainties of outsourcing. These uncertainties could lead
the products to be unsafe and, as is the case in a number of recent
examples, companies may have to end up in recalling their products.
As a result of these problems, there is a need to develop a
methodology for selecting suppliers globally in view of risks
associated with low quality and late delivery. Accordingly, we
developed a two-stage stochastic model that captures the risks
associated with uncertainty in quality and delivery as well as a
solution procedure for the model. The stochastic model developed
simultaneously optimizes supplier selection and purchase quantities
under price discounts over a time horizon. In particular, our target is
the study of global organizations with multiple sites and multiple
overseas suppliers, where the pricing is offered in suppliers’ local
currencies. Our proposed methodology is applied to a case study for a
US automotive company having two assembly plants and four
potential global suppliers to illustrate how the proposed model works
in practice.
Abstract: In this paper a new model for center of motion
creating is proposed. This new method uses cables. So, it is very
useful in robots because it is light and has easy assembling process.
In the robots which need to be in touch with some things this method
is so useful. It will be described in the following. The accuracy of the
idea is proved by two experiments. This system could be used in the
robots which need a fixed point in the contact with some things and
make a circular motion.
Abstract: The degradation of concrete due to various hygrochemo-
mechanical actions is inevitable for the structures particularly
built to store water. Therefore, it is essential to determine the material
properties of dam-like structures due to ageing to predict the behavior
of such structures after a certain age. The degraded material
properties are calculated by introducing isotropic degradation index.
The predicted material properties are used to study the behavior of
aged dam at different ages. The dam is modeled by finite elements
and displacement and is considered as an unknown variable. The
parametric study reveals that the displacement is quite larger for
comparatively lower design life of the structure because the
degradation of elastic properties depends on the design life of the
dam. The stresses in dam cam be unexpectedly large at any age with
in the design life. The outcomes of the present study indicate the
importance of the consideration ageing effect of concrete exposed to
water for the safe design of dam throughout its life time.
Abstract: The Figaro AM-1 sensor module which employs TGS
2600 model gas sensor in air quality assessment was used. The
system was coupled with a microprocessor that enables sensor
module to create warning message via telephone. This low cot sensor
system’s performance was compared with a DiagNose II commercial
electronic nose system. Both air quality sensor and electronic nose
system employ metal oxide chemical gas sensors. In the study
experimental setup, data acquisition methods for electronic nose
system, and performance of the low cost air quality system were
evaluated and explained.
Abstract: Construction and reconstruction of settlements and
individual municipalities, environmental management and the
creation, deployment of the forces of production and building
transport and technical equipment requires a large expenditure of
material and human resources. That is why the economic aspects of
the majority decision in these planes built in the foreground and are
often decisive. Thereby but more serious is that the economic aspects
of the settlement, the creation and function remain in their whole,
unprocessed, and cannot speak of a set of individual techniques and
methods traditional indicators and experiments with new approaches.
This is true both at the level of the national economy, and in their
own urban designs. Still a few remain identified specific economic
shaping patterns of settlement and the less it is possible to speak of
their control. Also practical assessing economics of specific solutions
are often used non-apt indicators in addition to economics usually
identifies with the lowest acquisition cost or high-intensity land use
with little regard for functional efficiency and little studied much
higher operating and maintenance costs".
Abstract: Biodiesel, as an alternative renewable fuel, has been
receiving increasing attention due to the limited supply of fossil fuels
and the increasing need for energy. Microalgae are promising source
for lipids, which can be converted to biodiesel. The biodiesel
production from microalgae lipids using lipase catalyzed reaction in
supercritical CO2 medium has several advantages over conventional
production processes. However, identifying the optimum microalgae
lipid extraction and transesterification conditions is still a challenge.
In this study, the quality of biodiesel produced from lipids extracted
from Scenedesmus sp. and their enzymatic transesterification using
supercritical carbon dioxide have been investigated. At the optimum
conditions, the highest biodiesel production yield was found to be
82%. The fuel properties of the produced biodiesel, without any
separation step, at optimum reaction condition, were determined and
compared to ASTM standards. The properties were found to comply
with the limits, and showed a low glycerol content, without any
separation step.
Abstract: Radial profiles of particle velocities were investigated
in a 6.1m high methanol-to-olefins cold model experimental device
using a TSI laser Doppler velocimeter. The effect of axial height on
flow development was not obvious in fully developed region under the
same operating condition. Superficial gas velocity and solid
circulating rate had significant influence on particle velocity in the
center region of the riser. Besides, comparisons among rising,
descending and average particle velocity were conducted. The particle
average velocity was similar to the rising particle velocity and higher
than the descending particle velocity in radial locations except the wall
region of riser.
Abstract: In this study free vibration analysis of aluminum
honeycomb sandwich structures were carried out experimentally and
numerically. The natural frequencies and mode shapes of sandwich
structures fabricated with different configurations for clamped-free
boundary condition were determined. The effects of lower and upper
face sheet thickness, the core material thickness, cell diameter, cell
angle and foil thickness on the vibration characteristics were
examined. The numerical studies were performed with ANSYS
package. While the sandwich structures were modeled in ANSYS the
continuum model was used. Later, the numerical results were
compared with the experimental findings.