Abstract: To explore how the brain may recognise objects in its
general,accurate and energy-efficient manner, this paper proposes the
use of a neuromorphic hardware system formed from a Dynamic
Video Sensor (DVS) silicon retina in concert with the SpiNNaker
real-time Spiking Neural Network (SNN) simulator. As a first step
in the exploration on this platform a recognition system for dynamic
hand postures is developed, enabling the study of the methods used
in the visual pathways of the brain. Inspired by the behaviours of
the primary visual cortex, Convolutional Neural Networks (CNNs)
are modelled using both linear perceptrons and spiking Leaky
Integrate-and-Fire (LIF) neurons.
In this study’s largest configuration using these approaches, a
network of 74,210 neurons and 15,216,512 synapses is created and
operated in real-time using 290 SpiNNaker processor cores in parallel
and with 93.0% accuracy. A smaller network using only 1/10th of the
resources is also created, again operating in real-time, and it is able
to recognise the postures with an accuracy of around 86.4% - only
6.6% lower than the much larger system. The recognition rate of the
smaller network developed on this neuromorphic system is sufficient
for a successful hand posture recognition system, and demonstrates
a much improved cost to performance trade-off in its approach.
Abstract: Hybrid electric vehicles can reduce pollution and
improve fuel economy. Power-split hybrid electric vehicles (HEVs)
provide two power paths between the internal combustion engine
(ICE) and energy storage system (ESS) through the gears of an
electrically variable transmission (EVT). EVT allows ICE to operate
independently from vehicle speed all the time. Therefore, the ICE can
operate in the efficient region of its characteristic brake specific fuel
consumption (BSFC) map. The two-mode powertrain can operate in
input-split or compound-split EVT modes and in four different fixed
gear configurations. Power-split architecture is advantageous because
it combines conventional series and parallel power paths. This
research focuses on input-split and compound-split modes in the
two-mode power-split powertrain. Fuzzy Logic Control (FLC) for an
internal combustion engine (ICE) and PI control for electric machines
(EMs) are derived for the urban driving cycle simulation. These
control algorithms reduce vehicle fuel consumption and improve ICE
efficiency while maintaining the state of charge (SOC) of the energy
storage system in an efficient range.
Abstract: This study will examine how the therapeutic factors
(therapeutic catharsis-seeking and game-efficacy of the game player)
and self-construal factors (independent and interdependent
self-construal of the game player) as well as social capital factors
(bonding and bridging social capital of the game player) affect
aggression in the game. Results show that both therapeutic
catharsis-seeking and game self-efficacy are particularly important to
the players since they cause the game players’ aggressive tendencies to
be greatly diminished. Independent self-construal reduces the level of
the players’ aggression. Interestingly enough, the bonding social
capital enhances the level of the players’ aggression, while individuals
with bridging social capital did not show any significant effects. The
results and implications will be discussed herein.
Abstract: A dip-coating process has been used to form an
asymmetric silica membrane with improved membrane performance
and reproducibility. First, we deposited repeatedly silica on top of a
commercial alumina membrane support to improve its structural
make up. The membrane is further processed under clean room
conditions to avoid dust impurity and subsequent drying in an oven
for high thermal, chemical and physical stability. The resulting
asymmetric membrane exhibits a gradual change in the membrane
layer thickness. Compared to the support, the dual-layer process
improves the gas flow rates. For the scientific applications for natural
gas purification, CO2, CH4 and H2 gas flow rates were. In addition,
the membrane selectively separated hydrogen.
Abstract: Distributed applications deployed on LEO satellites
and ground stations require substantial communication between
different members in a constellation to overcome the earth
coverage barriers imposed by GEOs. Applications running on LEO
constellations suffer the earth line-of-sight blockage effect. They
need adequate lab testing before launching to space. We propose
a scalable cloud-based network simulation framework to simulate
problems created by the earth line-of-sight blockage. The framework
utilized cloud IaaS virtual machines to simulate LEO satellites
and ground stations distributed software. A factorial ANOVA
statistical analysis is conducted to measure simulator overhead on
overall communication performance. The results showed a very low
simulator communication overhead. Consequently, the simulation
framework is proposed as a candidate for testing LEO constellations
with distributed software in the lab before space launch.
Abstract: Complex lifting entry was selected for precise landing
performance during the Mars Science Laboratory entry. This study
aims to develop the three-dimensional numerical method for precise
computation and the surface panel method for rapid engineering
prediction. Detailed flow field analysis for Mars exploration mission
was performed by carrying on a series of fully three-dimensional
Navier-Stokes computations. The static aerodynamic performance was
then discussed, including the surface pressure, lift and drag coefficient,
lift-to-drag ratio with the numerical and engineering method.
Computation results shown that the shock layer is thin because of
lower effective specific heat ratio, and that calculated results from both
methods agree well with each other, and is consistent with the
reference data. Aerodynamic performance analysis shows that CG
location determines trim characteristics and pitch stability, and certain
radially and axially shift of the CG location can alter the capsule lifting
entry performance, which is of vital significance for the aerodynamic
configuration design and inner instrument layout of the Mars entry
capsule.
Abstract: In this paper we propose a computer-aided solution
with Genetic Algorithms in order to reduce the drafting of reports:
FMEA analysis and Control Plan required in the manufacture of the
product launch and improved knowledge development teams for
future projects. The solution allows to the design team to introduce
data entry required to FMEA. The actual analysis is performed using
Genetic Algorithms to find optimum between RPN risk factor and
cost of production. A feature of Genetic Algorithms is that they are
used as a means of finding solutions for multi criteria optimization
problems. In our case, along with three specific FMEA risk factors is
considered and reduce production cost. Analysis tool will generate
final reports for all FMEA processes. The data obtained in FMEA
reports are automatically integrated with other entered parameters in
Control Plan. Implementation of the solution is in the form of an
application running in an intranet on two servers: one containing
analysis and plan generation engine and the other containing the
database where the initial parameters and results are stored. The
results can then be used as starting solutions in the synthesis of other
projects. The solution was applied to welding processes, laser cutting
and bending to manufacture chassis for buses. Advantages of the
solution are efficient elaboration of documents in the current project
by automatically generating reports FMEA and Control Plan using
multiple criteria optimization of production and build a solid
knowledge base for future projects. The solution which we propose is
a cheap alternative to other solutions on the market using Open
Source tools in implementation.
Abstract: Exploration and exploitation capabilities are both
important within Operations as means for improvement when
managed separately, and for establishing dynamic improvement
capabilities when combined in balance. However, it is unclear what
exploration and exploitation capabilities imply in improvement and
development work within an Operations context. So, in order to
better understand how to develop exploration and exploitation
capabilities within Operations, the main characteristics of these
constructs needs to be identified and further understood. Thus, the
objective of this research is to increase the understanding about
exploitation and exploration characteristics, to concretize what they
translates to within the context of improvement and development
work in an Operations unit, and to identify practical challenges. A
literature review and a case study are presented. In the literature
review, different interpretations of exploration and exploitation are
portrayed, key characteristics have been identified, and a deepened
understanding of exploration and exploitation characteristics is
described. The case in the study is an Operations unit, and the aim is
to explore to what extent and in what ways exploration and
exploitation activities are part of the improvement structures and
processes. The contribution includes an identification of key
characteristics of exploitation and exploration, as well as an
interpretation of the constructs. Further, some practical challenges are
identified. For instance, exploration activities tend to be given low
priority, both in daily work as in the manufacturing strategy. Also,
the overall understanding about the concepts of exploitation and
exploration (or any similar aspect of dynamic improvement
capabilities) is very low.
Abstract: The paper develops a Non-Linear Model Predictive
Control (NMPC) of water quality in Drinking Water Distribution
Systems (DWDS) based on the advanced non-linear quality dynamics
model including disinfections by-products (DBPs). A special attention
is paid to the analysis of an impact of the flow trajectories prescribed
by an upper control level of the recently developed two-time scale
architecture of an integrated quality and quantity control in DWDS.
The new quality controller is to operate within this architecture in the
fast time scale as the lower level quality controller. The controller
performance is validated by a comprehensive simulation study based
on an example case study DWDS.
Abstract: Biomass briquette gasification is regarded as a
promising route for efficient briquette use in energy generation, fuels
and other useful chemicals. However, previous research has been
focused on briquette gasification in fixed bed gasifiers such as
updraft and downdraft gasifiers. Fluidised bed gasifier has the
potential to be effectively sized to medium or large scale. This study
investigated the use of fuel briquettes produced from blends of rice
husks and corn cobs biomass, in a bubbling fluidised bed gasifier.
The study adopted a combination of numerical equations and Aspen
Plus simulation software, to predict the product gas (syngas)
composition base on briquette density and biomass composition
(blend ratio of rice husks to corn cobs). The Aspen Plus model was
based on an experimentally validated model from the literature. The
results based on a briquette size 32 mm diameter and relaxed density
range of 500 to 650kg/m3, indicated that fluidisation air required in
the gasifier increased with increase in briquette density, and the
fluidisation air showed to be the controlling factor compared with the
actual air required for gasification of the biomass briquettes. The
mass flowrate of CO2 in the predicted syngas composition increased
with an increase in air flow, in the gasifier, while CO decreased and
H2 was almost constant. The ratio of H2 to CO for various blends of
rice husks and corn cobs did not significantly change at the designed
process air, but a significant difference of 1.0 was observed between
10/90 and 90/10 % blend of rice husks and corn cobs.
Abstract: This study was aimed to investigate the machining
stability of a spindle tool with different preloaded amount. To this end,
the vibration tests were conducted on the spindle unit with different
preload to assess the dynamic characteristics and machining stability
of the milling machine. Current results demonstrate that the tool tip
frequency response characteristics and the machining stabilities in X
and Y direction are affected to change due to the different preload of
spindle bearings. As found from the results, a high preloaded spindle
tool shows higher limited cutting depth at mid position, while a spindle
with low preload shows a higher limited depth. This indicates that the
machining stability of a milling machine is affected to vary by the
spindle unit when it was assembled with different bearing preload.
Abstract: More than 3000 plants of notable phyto-therapeutic
value grow in South Africa; these include Cissampelos capensis,
commonly known in Afrikaans as dawidjie or dawidjiewortel. C.
capensis is the most significant and popular medicinal plant used by
the Khoisan as well as other rural groups in the Western region of
South Africa. Its rhizomes are traditionally used to treat male fertility
problems. Yet, no studies have investigated the effects of this plant or
its extracts on human spermatozoa. Therefore, this study aimed at
investigating the effects of C. capensis rhizome extract (CRE)
fractions on ejaculated human spermatozoa in vitro. Spermatozoa
from a total of 77 semen samples were washed with human tubular
fluid medium supplemented with bovine serum albumin (HTF-BSA)
and incubated for 2 hours with 20 μg/ml progesterone (P4) followed
by incubation with different concentrations (0, 0.05, 0.5, 5, 50, 200
μg/ml) of fractionated CRE (F1=0% MeOH, F2=30% MeOH,
F3=60% MeOH and F4=100% MeOH) for 1.5 hours at 37°C. A
sample without addition of CRE fractions served as control. Samples
were analyzed for sperm motility, reactive oxygen species (ROS),
DNA-fragmentation, acrosome reaction and capacitation. Results
showed that F1 resulted in significantly higher values for ROS,
capacitation and hyper-activation compared to F2, F3, and F4 with
P4-stimulated samples generally having higher values. No significant
effect was found for the other parameters. In conclusion, alkaloids
present in F1 of CRE appear to have triggered sperm intrinsic ROS
production leading to sperm capacitation and acrosome reaction
induced by P4.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: Copper (I) oxide microparticles with the morphology
of cubic and hollow sphere were synthesized with the assistance of
surfactant as the shape controller. Both particles were then subjected
to study the catalytic activity and observed the results of shape effects
of catalysts on rate of catalytic reaction. The decolorizing reaction of
crystal violet and sodium hydroxide was chosen and measured the
decreasing of reactant with respect to times using spectrophotometer.
The result revealed that morphology of crystal had no effect on the
catalytic activity for crystal violet reaction but contributed to total
surface area predominantly.
Abstract: Nowadays, the rapid development of CAD systems’
programming environments results in the creation of multiple
downstream applications, which are developed and becoming
increasingly available. CAD based manufacturing simulations is
gradually following the same trend. Drilling is the most popular holemaking
process used in a variety of industries. A specially built piece
of software that deals with the drilling kinematics is presented. The
cutting forces are calculated based on the tool geometry, the cutting
conditions and the tool/work-piece materials. The results are verified
by experimental work. Finally, the response surface methodology
(RSM) is applied and mathematical models of the total thrust force
and the thrust force developed because of the main cutting edges are
proposed.
Abstract: Aluminium matrix composites with alumina
reinforcements give superior mechanical & physical properties. Their
applications in several fields like automobile, aerospace, defense,
sports, electronics, bio-medical and other industrial purposes are
becoming essential for the last several decades. In the present work,
fabrication of hybrid composite was done by Stir casting technique
using Al 6061 as a matrix with alumina and silicon carbide (SiC) as
reinforcement materials. The weight percentage of alumina is varied
from 2 to 4% and the silicon carbide weight percentage is maintained
constant at 2%. Hardness and wear tests are performed in the as cast
and heat treated conditions. Age hardening treatment was performed
on the specimen with solutionizing at 550°C, aging at two
temperatures (150 and 200°C) for different time durations. Hardness
distribution curves are drawn and peak hardness values are recorded.
Hardness increase was very sensitive with respect to the decrease in
aging temperature. There was an improvement in wear resistance of
the peak aged material when aged at lower temperature. Also
increase in weight percent of alumina, increases wear resistance at
lower temperature but opposite behavior was seen when aged at
higher temperature.
Abstract: The present study was aimed to examine the structure
of children’s adaptation during school transition and to identify a
commonality and dissimilarity at the elementary and junior high
school. 1,983 students in the 6th grade and 2,051 students in the 7th
grade were extracted by stratified two-stage random sampling and
completed the ASSESS that evaluated the school adaptation from the
view point of ‘general satisfaction’, ‘teachers’ support’, ‘friends’
support’, ‘anti-bullying relationship’, ‘prosocial skills’, and ‘academic
adaptation’. The 7th graders tend to be worse adaptation than the 6th
graders. A structural equation modeling showed the goodness of fit for
each grades. Both models were very similar but the 7th graders’ model
showed a lower coefficient at the pass from ‘teachers’ support’ to
‘friends’ support’. The role of ‘teachers’ support’ was decreased to
keep a good relation in junior high school. We also discussed how we
provide a continuous assistance for prevention of the 7th graders’ gap.
Abstract: Methicillin/multiple-resistant Staphylococcus aureus
(MRSA) are infectious bacteria that are resistant to common
antibiotics. A previous in silico study in our group has identified a
hypothetical protein SAV1226 as one of the potential drug targets. In
this study, we reported the bioinformatics characterization, as well as
cloning, expression, purification and kinetic assays of hypothetical
protein SAV1226 from methicillin/vancomycin-resistant
Staphylococcus aureus Mu50 strain. MALDI-TOF/MS analysis
revealed a low degree of structural similarity with known proteins.
Kinetic assays demonstrated that hypothetical protein SAV1226 is
neither a domain of an ATP dependent dihydroxyacetone kinase nor
of a phosphotransferase system (PTS) dihydroxyacetone kinase,
suggesting that the function of hypothetical protein SAV1226 might
be misannotated on public databases such as UniProt and
InterProScan 5.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: A compound parabolic concentrator (CPC) is a wellknown
non-imaging concentrator that will concentrate the solar
radiation onto receiver (PV cell). One of disadvantage of CPC is has
tall and narrow height compared to its diameter entry aperture area.
Therefore, for economic reason, a truncation had been done by
removed from the top of the full height CPC. This also will lead to
the decreases of concentration ratio but it will be negligible. In this
paper, the flux distribution of untruncated and truncated 2-D hollow
compound parabolic trough concentrator (hCPTC) design is
presented. The untruncated design has initial height H=193.4mm
with concentration ratio C_(2-D)=4. This paper presents the optical
simulation of compound parabolic trough concentrator using raytracing
software TracePro. Results showed that, after the truncation,
the height of CPC reduced 45% from initial height with the
geometrical concentration ratio only decrease 10%. Thus, the cost of
reflector and material dielectric usage can be saved especially at
manufacturing site.