Abstract: The irradiation of polymeric materials has received
much attention because it can produce diverse changes in chemical
structure and physical properties. Thus, studying the chemical and
structural changes of polymers is important in practice to achieve
optimal conditions for the modification of polymers. The effect of
gamma irradiation on the crystalline structure of poly(vinylidene
fluoride) (PVDF) has been investigated using differential scanning
calorimetry (DSC) and X-ray diffraction techniques (XRD). Gamma
irradiation was carried out in atmosphere air with doses between 100
kGy at 3,000 kGy with a Co-60 source. In the melting thermogram of
the samples irradiated can be seen a bimodal melting endotherm is
detected with two melting temperature. The lower melting
temperature is attributed to melting of crystals originally present and
the higher melting peak due to melting of crystals reorganized upon
heat treatment. These results are consistent with those obtained by
XRD technique showing increasing crystallinity with increasing
irradiation dose, although the melting latent heat is decreasing.
Abstract: The combination of multi–walled carbon nanotubes
(MWCNTs) with polymers offers an attractive route to reinforce the
macromolecular compounds as well as the introduction of new
properties based on morphological modifications or electronic
interactions between the two constituents. As they are only a few
nanometers in dimension, it offers ultra-large interfacial area per
volume between the nano-element and polymer matrix. Nevertheless,
the use of MWCNTs as a rough material in different applications has
been largely limited by their poor processability, insolubility, and
infusibility. Studies concerning the nanofiller reinforced polymer
composites are justified in an attempt to overcome these limitations.
This work presents one preliminary study of MWCNTs dispersion
into the PVDF homopolymer. For preparation, the composite
components were diluted in n,n-dimethylacetamide (DMAc) with
mechanical agitation assistance. After complete dilution, followed by
slow evaporation of the solvent at 60°C, the samples were dried.
Films of about 80 μm were obtained. FTIR and UV-Vis
spectroscopic techniques were used to characterize the
nanocomposites. The appearance of absorption bands in the FTIR
spectra of nanofilled samples, when compared to the spectrum of
pristine PVDF samples, are discussed and compared with the UV-Vis
measurements.
Abstract: This paper analyzes the institutionalization of social
protest in Spain. In the current crisis Podemos party seems to
represent the political positions of the most affected citizens by the
economic situation. It studies using quantitative techniques (statistical
bivariate analysis), focusing on the exploitation of several bases of
statistics data from the Center for Sociological and Research of
Spanish Government, 15M movement characterization to its
institutionalization in the Podemos party. Making a comparison
between the participant's profile by the 15M and the social bases of
Podemos votes. Data on the transformation of the socio-demographic
profile of the fans, connoisseurs and 15M participants and voters are
given.
Abstract: Large scale Indian manufacturers started
implementing Six Sigma to their supply core to fulfill the endless
need of high quality products. As well, they initiated encouraging
their suppliers to apply the well-ascertain SS management practice
and kept no resource for supplier enterprises, generally small midsized
enterprises to think for the admittance of Six Sigma as a quality
promotion drive. There are many issues to study for requisite changes
before the introduction of Six Sigma in auto SMEs. This paper
converges on impeding factors while implementing SS drive and also
pinpoints the gains achieved through successful implementation. The
result of this study suggest some operational guidelines for effective
implementation of Six Sigma from evidences acquired through
research questionnaire and interviews with industrial professionals,
apportioned to assort auto sector mid-sized enterprises (MSEs) in
India.
Abstract: Nowadays, food safety is a great public concern;
therefore, robust and effective techniques are required for detecting
the safety situation of goods. Hyperspectral Imaging (HSI) is an
attractive material for researchers to inspect food quality and safety
estimation such as meat quality assessment, automated poultry
carcass inspection, quality evaluation of fish, bruise detection of
apples, quality analysis and grading of citrus fruits, bruise detection
of strawberry, visualization of sugar distribution of melons,
measuring ripening of tomatoes, defect detection of pickling
cucumber, and classification of wheat kernels. HSI can be used to
concurrently collect large amounts of spatial and spectral data on the
objects being observed. This technique yields with exceptional
detection skills, which otherwise cannot be achieved with either
imaging or spectroscopy alone. This paper presents a nonlinear
technique based on kernel Fukunaga-Koontz transform (KFKT) for
detection of fat content in ground meat using HSI. The KFKT which
is the nonlinear version of FKT is one of the most effective
techniques for solving problems involving two-pattern nature. The
conventional FKT method has been improved with kernel machines
for increasing the nonlinear discrimination ability and capturing
higher order of statistics of data. The proposed approach in this paper
aims to segment the fat content of the ground meat by regarding the
fat as target class which is tried to be separated from the remaining
classes (as clutter). We have applied the KFKT on visible and nearinfrared
(VNIR) hyperspectral images of ground meat to determine
fat percentage. The experimental studies indicate that the proposed
technique produces high detection performance for fat ratio in ground
meat.
Abstract: Asphalt pavement itself is a mixture made up of mainly aggregates, binders, and fillers that acts as a composition used for pavement construction. An experimental program was setup to determine the fatigue performance test of Asphalt with three different grades of conventional binders. Asphalt specimen has achieved the maximum optimum bulk density and air voids with a consistent bulk density of 2.3 t/m3, with an air void of 5% ± 0.5, before loading into the Asphalt Mixture Performance Tested (AMPT) for fatigue test. The number of cycles is defined as the point where phase angle drops, which is caused by the formation of cracks due to the increasing micro cracks when asphalt is undergoing repeated cycles of loading. Thus, the data collected are analyzed using the drop of phase angle as failure criteria. Based in the data analyzed, it is evident that the fatigue life of asphalt lies on the grade of binder. The result obtained shows that all specimens do experience a drop in phase angle due to macro cracks in the asphalt specimen.
Abstract: Reinforced cement concrete is getting extensively used
for construction of different type of structures for the last one century.
During this period, we have constructed many structures like
buildings, bridges, industrial structures, pavement, water tanks etc.
using this construction material. These structures have been created
with huge investment of resources. It is essential to maintain those
structures in functional condition. Since deterioration in RCC
Structures is a common and natural phenomenon it is required to have
a detailed plan, methodology for structural repair and rehabilitation
shall be in place for dealing such issues. It is important to know exact
reason of distress, type of distress and correct method of repair
concrete structures. The different methods of repair are described in
paper according to distress category which can be refereed for repair.
Major finding of the study is that to protect our structure we need to
have maintenance frequency and correct material to be chosen for
repair. Also workmanship during repair needs to be taken utmost care
for quality repair.
Abstract: Ultrasonic metal welding has been the subject of ongoing research and development, most recently concentrating on metal joining in miniature devices, for example to allow solder-free wire bonding. As well as at the small scale, there are also opportunities to research the joining of thicker sheet metals and to widen the range of similar and dissimilar materials that can be successfully joined using this technology. This study presents the design, characterisation and test of a lateral-drive ultrasonic metal spot welding device. The ultrasonic metal spot welding horn is modelled using finite element analysis (FEA) and its vibration behaviour is characterised experimentally to ensure ultrasonic energy is delivered effectively to the weld coupon. The welding stack and fixtures are then designed and mounted on a test machine to allow a series of experiments to be conducted for various welding and ultrasonic parameters. Weld strength is subsequently analysed using tensile-shear tests. The results show how the weld strength is particularly sensitive to the combination of clamping force and ultrasonic vibration amplitude of the welding tip, but there are optimal combinations of these and also limits that must be clearly identified.
Abstract: In this paper, it is aimed to improve autonomous flight
performance of a load-carrying (payload: 3 kg and total: 6kg)
unmanned aerial vehicle (UAV) through active wing and horizontal
tail active morphing and also integrated autopilot system parameters
(i.e. P, I, D gains) and UAV parameters (i.e. extension ratios of wing
and horizontal tail during flight) design. For this purpose, a loadcarrying
UAV (i.e. ZANKA-II) is manufactured in Erciyes
University, College of Aviation, Model Aircraft Laboratory is
benefited. Optimum values of UAV parameters and autopilot
parameters are obtained using a stochastic optimization method.
Using this approach autonomous flight performance of UAV is
substantially improved and also in some adverse weather conditions
an opportunity for safe flight is satisfied. Active morphing and
integrated design approach gives confidence, high performance and
easy-utility request of UAV users.
Abstract: A composite material with carbon fiber and polymer
matrix has been used as adherent for manufacturing adhesive joints.
In order to evaluate different fiber orientations on joint performance,
the adherents with the 0°, ±15°, ±30°, ±45° fiber orientations were
used in the single lap joint configuration. The joints with an overlap
length of 25 mm were prepared according to the ASTM 1002
specifications and subjected to tensile loadings. The structural
adhesive used was a two-part epoxy to be cured at 70°C for an hour.
First, mechanical behaviors of the adherents were measured using
three point bending test. In the test, considerations were given to
stress to failure and elastic modulus. The results were compared with
theoretical ones using rule of mixture. Then, the joints were
manufactured in a specially prepared jig, after a proper surface
preparation. Experimental results showed that the fiber orientations
of the adherents affected the joint performance considerably; the
joints with ±45° adherents experienced the worst shear strength, half
of those with 0° adherents, and in general, there was a great
relationship between the fiber orientations and failure mechanisms.
Delamination problems were observed for many joints, which were
thought to be due to peel effects at the ends of the overlap. It was
proved that the surface preparation applied to the adherent surface
was adequate. For further explanation of the results, a numerical
work should be carried out using a possible non-linear analysis.
Abstract: This paper investigates the application of metallic
coatings on high fiber volume fraction carbon/epoxy polymer matrix
composites. For the grip of the metallic layer, a method of modifying
the surface of the composite by introducing a mixture of copper and
steel powder (filler powders) which can reduce the impact of thermal
spray particles. The powder was introduced to the surface at the time
of the forming. Arc spray was used to project the zinc coating layer.
The substrate was grit blasted to avoid poor adherence. The porosity, microstructure, and morphology of layers are
characterized by optical microscopy, SEM and image analysis. The
samples were studied also in terms of hardness and erosion resistance.
This investigation did not reveal any visible evidence damage to the
substrates. The hardness of zinc layer was about 25.94 MPa and the
porosity was around (∼6.70%). The erosion test showed that the zinc
coating improves the resistance to erosion. Based on the results
obtained, we can conclude that thermal spraying allows the production
of protective coating on PMC. Zinc coating has been identified as a
compatible material with the substrate. The filler powders layer
protects the substrate from the impact of hot particles and allows
avoiding the rupture of brittle carbon fibers.
Abstract: Smart metering and demand response are gaining
ground in industrial and residential applications. Smart Appliances
have been given concern towards achieving Smart home. The success
of Smart grid development relies on the successful implementation of
Information and Communication Technology (ICT) in power sector.
Smart Appliances have been the technology under development and
many new contributions to its realization have been reported in the
last few years. The role of ICT here is to capture data in real time,
thereby allowing bi-directional flow of information/data between
producing and utilization point; that lead a way for the attainment of
Smart appliances where home appliances can communicate between
themselves and provide a self-control (switch on and off) using the
signal (information) obtained from the grid. This paper depicts the
background on ICT for smart appliances paying a particular attention
to the current technology and identifying the future ICT trends for
load monitoring through which smart appliances can be achieved to
facilitate an efficient smart home system which promote demand
response program. This paper grouped and reviewed the recent
contributions, in order to establish the current state of the art and
trends of the technology, so that the reader can be provided with a
comprehensive and insightful review of where ICT for smart
appliances stands and is heading to. The paper also presents a brief
overview of communication types, and then narrowed the discussion
to the load monitoring (Non-intrusive Appliances Load Monitoring
‘NALM’). Finally, some future trends and challenges in the further
development of the ICT framework are discussed to motivate future
contributions that address open problems and explore new
possibilities.
Abstract: The very well-known stacked sets of numbers referred
to as Pascal’s triangle present the coefficients of the binomial
expansion of the form (x+y)n. This paper presents an approach (the
Staircase Horizontal Vertical, SHV-method) to the generalization of
planar Pascal’s triangle for polynomial expansion of the form
(x+y+z+w+r+⋯)n. The presented generalization of Pascal’s triangle
is different from other generalizations of Pascal’s triangles given in
the literature. The coefficients of the generalized Pascal’s triangles,
presented in this work, are generated by inspection, using embedded
Pascal’s triangles. The coefficients of I-variables expansion are
generated by horizontally laying out the Pascal’s elements of (I-1)
variables expansion, in a staircase manner, and multiplying them with
the relevant columns of vertically laid out classical Pascal’s elements,
hence avoiding factorial calculations for generating the coefficients
of the polynomial expansion. Furthermore, the classical Pascal’s
triangle has some pattern built into it regarding its odd and even
numbers. Such pattern is known as the Sierpinski’s triangle. In this
study, a presentation of Sierpinski-like patterns of the generalized
Pascal’s triangles is given. Applications related to those coefficients
of the binomial expansion (Pascal’s triangle), or polynomial
expansion (generalized Pascal’s triangles) can be in areas of
combinatorics, and probabilities.
Abstract: The recent instability in economy was found to be
influencing the situation in Malaysia whether directly or indirectly.
Taking that into consideration, the government needs to find the best
approach to balance its citizen’s socio-economic strata level urgently.
Through education platform is among the efforts planned and acted
upon for the purpose of balancing the effects of the influence,
through the exposure of social entrepreneurial activity towards youth
especially those in higher institution level. Armed with knowledge
and skills that they gained, with the support by entrepreneurial
culture and environment while in campus; indirectly, the students will
lean more on making social entrepreneurship as a career option when
they graduate. Following the issues of marketability and workability
of current graduates that are becoming dire, research involving how
far the willingness of student to create social innovation that
contribute to the society without focusing solely on personal gain is
relevant enough to be conducted. With that, this research is
conducted with the purpose of identifying the level of entrepreneurial
intention and social entrepreneurship among higher institution
students in Malaysia. Stratified random sampling involves 355
undergraduate students from five public universities had been made
as research respondents and data were collected through surveys. The
data was then analyzed descriptively using min score and standard
deviation. The study found that the entrepreneurial intention of higher
education students are on moderate level, however it is the contrary
for social entrepreneurship activities, where it was shown on a high
level. This means that while the students only have moderate level of
willingness to be a social entrepreneur, they are very committed to
created social innovation through the social entrepreneurship
activities conducted. The implication from this study can be
contributed towards the higher institution authorities in prediction the
tendency of student in becoming social entrepreneurs. Thus, the
opportunities and facilities for realizing the courses related to social
entrepreneurship must be created expansively so that the vision of
creating as many social entrepreneurs as possible can be achieved.
Abstract: We present an approach to triangle mesh simplification
designed to be executed on the GPU. We use a quadric error metric
to calculate an error value for each vertex of the mesh and order all
vertices based on this value. This step is followed by the parallel
removal of a number of vertices with the lowest calculated error
values. To allow for the parallel removal of multiple vertices we use
a set of per-vertex boundaries that prevent mesh foldovers even when
simplification operations are performed on neighbouring vertices. We
execute multiple iterations of the calculation of the vertex errors,
ordering of the error values and removal of vertices until either a
desired number of vertices remains in the mesh or a minimum error
value is reached. This parallel approach is used to speed up the
simplification process while maintaining mesh topology and avoiding
foldovers at every step of the simplification.
Abstract: The present paper examines the impact noise
transmission through some floor building assemblies. The Acoubat
software numerical simulation has been used to simulate the impact
noise transmission through different floor configurations used in
Algerian construction mode. The results are compared with the
available measurements. We have developed two experimental
methods, i) field method, and ii) laboratory method using Brüel and
Kjær equipments. The results show that the different cases of floor
configurations need some improvement to ensure the acoustic
comfort in the receiving apartment. The recommended value of the
impact sound level in the receiving room should not exceed 58 dB.
The important results obtained in this paper can be used as platform
to improve the Algerian building acoustic regulation aimed at the
construction of the multi-storey residential building.
Abstract: This paper describes two methods for the reduction of
the peak input current during the boosting of Dickson charge pumps.
Both methods are implemented in the fully integrated Dickson charge
pumps of a high-voltage display driver chip for smart-card
applications. Experimental results reveal good correspondence with
Spice simulations and show a reduction of the peak input current by a
factor of 6 during boosting.
Abstract: E-Learning enables the users to learn at anywhere at
any time. In E-Learning systems, authenticating the E-Learning user
has security issues. The usage of appropriate communication
networks for providing the internet connectivity for E-learning is
another challenge. WiMAX networks provide Broadband Wireless
Access through the Multicast Broadcast Service so these networks
can be most suitable for E-Learning applications. The authentication
of E-Learning user is vulnerable to session hijacking problems. The
repeated authentication of users can be done to overcome these
issues. In this paper, session based Profile Caching Authentication is
proposed. In this scheme, the credentials of E-Learning users can be
cached at authentication server during the initial authentication
through the appropriate subscriber station. The proposed cache based
authentication scheme performs fast authentication by using cached
user profile. Thus, the proposed authentication protocol reduces the
delay in repeated authentication to enhance the security in ELearning.
Abstract: Pain management is a question of quality of life and
an indicator for nursing quality. Chronic pain which is predominant
in oncology and palliative nursing situations is perceived today as a
multifactorial, individual emotional experience with specific
characteristics including the sociocultural dimension when dealing
with migrant patients. This dimension of chronic pain is of major
importance in professional nursing of migrant patients in hospices or
palliative care units. Objectives of the study are: 1. To find out more
about the sociocultural views on pain and nursing care, on customs
and nursing practices connected with pain of both Turkish Muslim
and German Christian women, 2. To improve individual and family
oriented nursing practice with view to sociocultural needs of patients
in severe pain in palliative care. In a qualitative-explorative comparative study 4 groups of women,
Turkish Muslims immigrants (4 from the first generation, 5 from the
second generation) and German Christian women of two generations
(5 of each age group) of the same age groups as the Turkish women
and with similar educational backgrounds were interviewed (semistructured
ethnographic interviews using Spradley, 1979) on their
perceptions and experiences of pain and nursing care within their
families. For both target groups the presentation will demonstrate the
following results in detail: Utterance of pain as well as “private” and
“public” pain vary within different societies and cultures. Permitted
forms of pain utterance are learned in childhood and determine
attitudes and expectations in adulthood. Language, especially when
metaphors and symbols are used, plays a major role for
misunderstandings. The sociocultural context of illness may include
specific beliefs that are important to the patients and yet seem more
than far-fetched from a biomedical perspective. Pain can be an
influential factor in family relationships where respect or hierarchies
do not allow the direct utterance of individual needs. Specific
resources are often, although not exclusively, linked to religious
convictions and are significantly helpful in reducing pain. The discussion will evaluate the results of the study with view to
the relevant literature and present nursing interventions and
instruments beyond medication that are helpful when dealing with
patients from various socio-cultural backgrounds in painful end-oflife
situations.
Abstract: Many embankment dams have suffered failures during
earthquakes due to the increase of pore water pressure under seismic
loading. After analyzing of the behavior of embankment dams under
severe earthquakes, major advances have been attained in the
understanding of the seismic action on dams. The present study concerns numerical analysis of the seismic
response of earth dams. The procedure uses a nonlinear stress-strain
relation incorporated into the code FLAC2D based on the finite
difference method. This analysis provides the variation of the pore
water pressure and horizontal displacement.