Abstract: In this paper, periodic force operation of a wastewater treatment process has been studied for the improved process performance. A previously developed dynamic model for the process is used to conduct the performance analysis. The static version of the model was utilized first to determine the optimal productivity conditions for the process. Then, feed flow rate in terms of dilution rate i.e. (D) is transformed into sinusoidal function. Nonlinear model predictive control algorithm is utilized to regulate the amplitude and period of the sinusoidal function. The parameters of the feed cyclic functions are determined which resulted in improved productivity than the optimal productivity under steady state conditions. The improvement in productivity is found to be marginal and is satisfactory in substrate conversion compared to that of the optimal condition and to the steady state condition, which corresponds to the average value of the periodic function. Successful results were also obtained in the presence of modeling errors and external disturbances.
Abstract: Typically thermal power plants are located near to
surface coal mines that produce huge amount of fly ash as a waste
byproduct. Disposal of fly ash causes significant economic and
environmental problems. Now-a-days, research is going on for bulk
utilization of fly ash. In order to increase its percentage utilization, an
investigation was carried out to evaluate its potential for haul road
construction. This paper presents the laboratory California bearing
ratio (CBR) tests and evaluates the effect of lime on CBR behavior of
fly ash - mine overburden mixes. Tests were performed with different
percentages of lime (2%, 3%, 6%, and 9%). The results show that the
increase in bearing ratio of fly ash-overburden mixes was achieved
by lime treatment. Scanning electron microscopy (SEM) analyses
were conducted on 28 days cured specimens. The SEM study showed
that the bearing ratio development is related to the microstructural
development.
Abstract: A. niger XP isolated from Vietnam produces very low amount of acidic phytase with optimal pH at 2.5 and 5.5. The phytase production of this strain was successfully improved through gene cloning and expression. A 1.4 - kb DNA fragment containing the coding region of the phyA gene was amplified by PCR and inserted into the expression vector pPICZαA with a signal peptide α- factor, under the control of AOX1 promoter. The recombined plasmid was transformed into the host strain P. pastoris KM71H and X33 by electroporation. Both host strains could efficiently express and secret phytase. The multicopy strains were screened for over expression of phytase. All the selected multicopy strains of P. pastoris X33 were examined for phytase activity, the maximum phytase yield of 1329 IU/ml was obtained after 4 days of incubation in medium BMM. The recombinant protein with MW of 97.4 KW showed to be the only one protein secreted in the culture broth. Multicopy transformant P. pastoris X33 supposed to be potential candidate for producing the commercial preparation of phytase.
Abstract: Sustainability in rural production system can only be achieved if it can suitably satisfy the local requirement as well as the outside demand with the changing time. With the increased pressure from the food sector in a globalised world, the agrarian economy
needs to re-organise its cultivable land system to be compatible with new management practices as well as the multiple needs of various stakeholders and the changing resource scenario. An attempt has been made to transform this problem into a multi-objective decisionmaking problem considering various objectives, resource constraints and conditional constraints. An interactive fuzzy multi-objective
programming approach has been used for such a purpose taking a
case study in Indian context to demonstrate the validity of the method.
Abstract: The objective of present work is to stimulate the
machining of material by electrical discharge machining (EDM) to
give effect of input parameters like discharge current (Ip), pulse on
time (Ton), pulse off time (Toff) which can bring about changes in the
output parameter, i.e. material removal rate. Experimental data was
gathered from die sinking EDM process using copper electrode and
Medium Carbon Steel (AISI 1040) as work-piece. The rules of
membership function (MF) and the degree of closeness to the
optimum value of the MMR are within the upper and lower range of
the process parameters. It was found that proposed fuzzy model is in
close agreement with the experimental results. By Intelligent, model
based design and control of EDM process parameters in this study
will help to enable dramatically decreased product and process
development cycle times.
Abstract: The paper discusses a 3D numerical solution of the inverse boundary problem for a continuous casting process of alloy. The main goal of the analysis presented within the paper was to estimate heat fluxes along the external surface of the ingot. The verified information on these fluxes was crucial for a good design of a mould, effective cooling system and generally the whole caster. In the study an enthalpy-porosity technique implemented in Fluent package was used for modeling the solidification process. In this method, the phase change interface was determined on the basis of the liquid fraction approach. In inverse procedure the sensitivity analysis was applied for retrieving boundary conditions. A comparison of the measured and retrieved values showed a high accuracy of the computations. Additionally, the influence of the accuracy of measurements on the estimated heat fluxes was also investigated.
Abstract: Thermo-chemical treatment (TCT) such as pyrolysis
is getting recognized as a valid route for (i) materials and valuable
products and petrochemicals recovery; (ii) waste recycling; and (iii)
elemental characterization. Pyrolysis is also receiving renewed
attention for its operational, economical and environmental
advantages. In this study, samples of polyethylene terephthalate
(PET) and polystyrene (PS) were pyrolysed in a microthermobalance
reactor (using a thermogravimetric-TGA setup). Both
polymers were prepared and conditioned prior to experimentation.
The main objective was to determine the kinetic parameters of the
depolymerization reactions that occur within the thermal degradation
process. Overall kinetic rate constants (ko) and activation energies
(Eo) were determined using the general kinetics theory (GKT)
method previously used by a number of authors. Fitted correlations
were found and validated using the GKT, errors were within ± 5%.
This study represents a fundamental step to pave the way towards the
development of scaling relationship for the investigation of larger
scale reactors relevant to industry.
Abstract: This paper uses quasi-steady molecular statics model
and diamond tool to carry out simulation temperature rise of nanoscale
orthogonal cutting single-crystal silicon. It further qualitatively
analyzes temperature field of silicon workpiece without considering
heat transfer and considering heat transfer. This paper supposes that
the temperature rise of workpiece is mainly caused by two heat sources:
plastic deformation heat and friction heat. Then, this paper develops a
theoretical model about production of the plastic deformation heat and
friction heat during nanoscale orthogonal cutting. After the increased
temperature produced by these two heat sources are added up, the
acquired total temperature rise at each atom of the workpiece is
substituted in heat transfer finite difference equation to carry out heat
transfer and calculates the temperature field in each step and makes
related analysis.
Abstract: In this paper, we present a new method for
incorporating global shift invariance in support vector machines.
Unlike other approaches which incorporate a feature extraction stage,
we first scale the image and then classify it by using the modified
support vector machines classifier. Shift invariance is achieved by
replacing dot products between patterns used by the SVM classifier
with the maximum cross-correlation value between them. Unlike the
normal approach, in which the patterns are treated as vectors, in our
approach the patterns are treated as matrices (or images). Crosscorrelation
is computed by using computationally efficient
techniques such as the fast Fourier transform. The method has been
tested on the ORL face database. The tests indicate that this method
can improve the recognition rate of an SVM classifier.
Abstract: This paper describes the challenges on the requirements engineering for developing an enterprise applications in higher
education environment. The development activities include software implementation, maintenance, and enhancement and support for online
transaction processing and overnight batch processing.
Generally, an enterprise application for higher education environment
may include Student Information System (SIS), HR/Payroll system,
Financial Systems etc. By the way, there are so many challenges in
requirement engineering phases in order to provide two distinctive
services that are production processing support and systems
development.
Abstract: A novel concept to balance and tradeoff between
make-to-stock and make-to-order has been hybrid MTS/MTO production context. One of the most important decisions involved in
the hybrid MTS/MTO environment is determining whether a product
is manufactured to stock, to order, or hybrid MTS/MTO strategy. In this paper, a model based on analytic network process is developed to tackle the addressed decision. Since the regarded decision deals with
the uncertainty and ambiguity of data as well as experts- and
managers- linguistic judgments, the proposed model is equipped with
fuzzy sets theory. An important attribute of the model is its generality due to diverse decision factors which are elicited from the
literature and developed by the authors. Finally, the model is validated by applying to a real case study to reveal how the proposed
model can actually be implemented.
Abstract: Nano MgO has been synthesized by hydration and
dehydration method by modifies the commercial MgO. The prepared
MgO had been investigated as a heterogeneous base catalyst for
transesterification process for biodiesel production using palm oil.
TGA, FT-IR and XRD results obtained from this study lie each other
and proved in the formation of nano MgO from decomposition of
Mg(OH)2. This study proved that the prepared nano MgO was a
better base transesterification catalyst compared to commercial MgO.
The nano MgO calcined at 600ºC had gives the highest conversion of
51.3% of palm oil to biodiesel.
Abstract: In a state-of-the-art industrial production line of
photovoltaic products the handling and automation processes are of
particular importance and implication. While processing a fully
functional crystalline solar cell an as-cut photovoltaic wafer is subject
to numerous repeated handling steps. With respect to stronger
requirements in productivity and decreasing rejections due to defects
the mechanical stress on the thin wafers has to be reduced to a
minimum as the fragility increases by decreasing wafer thicknesses.
In relation to the increasing wafer fragility, researches at the
Fraunhofer Institutes IPA and CSP showed a negative correlation
between multiple handling processes and the wafer integrity. Recent
work therefore focused on the analysis and optimization of the dry
wafer stack separation process with compressed air. The achievement
of a wafer sensitive process capability and a high production
throughput rate is the basic motivation in this research.
Abstract: Low temperature (LT) is one of the most abiotic
stresses causing loss of yield in wheat (T. aestivum). Four major
genes in wheat (Triticum aestivum L.) with the dominant alleles
designated Vrn–A1,Vrn–B1,Vrn–D1 and Vrn4, are known to have
large effects on the vernalization response, but the effects on cold
hardiness are ambiguous. Poor cold tolerance has restricted winter
wheat production in regions of high winter stress [9]. It was known
that nearly all wheat chromosomes [5] or at least 10 chromosomes of
21 chromosome pairs are important in winter hardiness [15]. The
objective of present study was to clarify the role of each chromosome
in cold tolerance. With this purpose we used 20 isogenic lines of
wheat. In each one of these isogenic lines only a chromosome from
‘Bezostaya’ variety (a winter habit cultivar) was substituted to
‘Capple desprez’ variety. The plant materials were planted in
controlled conditions with 20º C and 16 h day length in moderately
cold areas of Iran at Karaj Agricultural Research Station in 2006-07
and the acclimation period was completed for about 4 weeks in a
cold room with 4º C. The cold hardiness of these isogenic lines was
measured by LT50 (the temperature in which 50% of the plants are
killed by freezing stress).The experimental design was completely
randomized block design (RCBD)with three replicates. The results
showed that chromosome 5A had a major effect on freezing
tolerance, and then chromosomes 1A and 4A had less effect on this
trait. Further studies are essential to understanding the importance of
each chromosome in controlling cold hardiness in wheat.
Abstract: This research aimed to study correlation between
work satisfaction and organization core value of officers in
Waterworks Authority, Bangkean Branch. Sample group of the study
was 112 officers who worked in the Waterworks Authority,
Bangkean Branch. Questionnaires were employed as a research tools,
while, Percentage, Mean, Standard Deviation, T-test, One-way
ANOVA, and Pearson Product Moment Correlation were claimed as
statistics used in this study. Researcher found that overall and
individual aspects of work satisfaction namely, work characteristic,
work progress, and colleagues significantly correlated with
organization core value in aspect of perception in choice of work at
0.5, 0.01, and 0.01 respectively. Also, such aspects were compatible
with income at .05 which indicated the low level of correlation, mid
low correlation respectively at the same direction, same direction,
opposite direction, and same direction, correspondingly.
Abstract: The aims of this study were to compare the
differences of being good membership behavior among faculties and
staffs of Suan Sunandha Rajabhat University with different sex, age,
income, education, marital status, and working period, and
investigate the relationships between organizational commitment and
being good membership behavior. The research methodology
employed a questionnaire as a quantitative method. The respondents
were 305 faculties and staffs of Suan Sunandha Rajabhat University.
This research used Percentage, Mean, Standard Deviation, t-test,
One-Way ANOVA Analysis of Variance, and Pearson’s Product
Moment Correlation Coefficient in data analysis. The results showed
that organizational commitment among faculties and staffs of Suan
Sunandha Rajabhat University was at a high level. In addition,
differences in sex, age, income, education, marital status, and
working period revealed differences in being good membership
behavior. The results also indicated that organizational commitment
was significantly related to being good membership behavior.
Abstract: Kernel function, which allows the formulation of nonlinear variants of any algorithm that can be cast in terms of dot products, makes the Support Vector Machines (SVM) have been successfully applied in many fields, e.g. classification and regression. The importance of kernel has motivated many studies on its composition. It-s well-known that reproducing kernel (R.K) is a useful kernel function which possesses many properties, e.g. positive definiteness, reproducing property and composing complex R.K by simple operation. There are two popular ways to compute the R.K with explicit form. One is to construct and solve a specific differential equation with boundary value whose handicap is incapable of obtaining a unified form of R.K. The other is using a piecewise integral of the Green function associated with a differential operator L. The latter benefits the computation of a R.K with a unified explicit form and theoretical analysis, whereas there are relatively later studies and fewer practical computations. In this paper, a new algorithm for computing a R.K is presented. It can obtain the unified explicit form of R.K in general reproducing kernel Hilbert space. It avoids constructing and solving the complex differential equations manually and benefits an automatic, flexible and rigorous computation for more general RKHS. In order to validate that the R.K computed by the algorithm can be used in SVM well, some illustrative examples and a comparison between R.K and Gaussian kernel (RBF) in support vector regression are presented. The result shows that the performance of R.K is close or slightly superior to that of RBF.
Abstract: Nowadays, the demand for high product quality
focuses extensive attention to the quality of machined surface. The
(CNC) milling machine facilities provides a wide variety of
parameters set-up, making the machining process on the glass
excellent in manufacturing complicated special products compared to
other machining processes. However, the application of grinding
process on the CNC milling machine could be an ideal solution to
improve the product quality, but adopting the right machining
parameters is required. In glass milling operation, several machining
parameters are considered to be significant in affecting surface
roughness. These parameters include the lubrication pressure, spindle
speed, feed rate and depth of cut. In this research work, a fuzzy logic
model is offered to predict the surface roughness of a machined
surface in glass milling operation using CBN grinding tool. Four
membership functions are allocated to be connected with each input
of the model. The predicted results achieved via fuzzy logic model
are compared to the experimental result. The result demonstrated
settlement between the fuzzy model and experimental results with the
93.103% accuracy.
Abstract: The present paper develops and validates a numerical procedure for the calculation of turbulent combustive flow in converging and diverging ducts and throuh simulation of the heat transfer processes, the amount of production and spread of Nox pollutant has been measured. A marching integration solution procedure employing the TDMA is used to solve the discretized equations. The turbulence model is the Prandtl Mixing Length method. Modeling the combustion process is done by the use of Arrhenius and Eddy Dissipation method. Thermal mechanism has been utilized for modeling the process of forming the nitrogen oxides. Finite difference method and Genmix numerical code are used for numerical solution of equations. Our results indicate the important influence of the limiting diverging angle of diffuser on the coefficient of recovering of pressure. Moreover, due to the intense dependence of Nox pollutant to the maximum temperature in the domain with this feature, the Nox pollutant amount is also in maximum level.
Abstract: This paper argues that a product development exercise
involves in addition to the conventional stages, several decisions
regarding other aspects. These aspects should be addressed
simultaneously in order to develop a product that responds to the
customer needs and that helps realize objectives of the stakeholders
in terms of profitability, market share and the like. We present a
framework that encompasses these different development
dimensions. The framework shows that a product development
methodology such as the Quality Function Deployment (QFD) is the
basic tool which allows definition of the target specifications of a
new product. Creativity is the first dimension that enables the
development exercise to live and end successfully. A number of
group processes need to be followed by the development team in
order to ensure enough creativity and innovation. Secondly,
packaging is considered to be an important extension of the product.
Branding strategies, quality and standardization requirements,
identification technologies, design technologies, production
technologies and costing and pricing are also integral parts to the
development exercise. These dimensions constitute the proposed
framework. The paper also presents a mathematical model used to
calculate the design targets based on the target costing principle. The
framework is used to study a case of a new product development in
the telecommunications services sector.