Abstract: Implemented 5-bit 125-MS/s successive
approximation register (SAR) analog to digital converter (ADC) on
FPGA is presented in this paper.The design and modeling of a high
performance SAR analog to digital converter are based on monotonic
capacitor switching procedure algorithm .Spartan 3 FPGA is chosen
for implementing SAR analog to digital converter algorithm. SAR
VHDL program writes in Xilinx and modelsim uses for showing
results.
Abstract: Network on a chip (NoC) has been proposed as a viable solution to counter the inefficiency of buses in the current VLSI on-chip interconnects. However, as the silicon chip accommodates more transistors, the probability of transient faults is increasing, making fault tolerance a key concern in scaling chips. In packet based communication on a chip, transient failures can corrupt the data packet and hence, undermine the accuracy of data communication. In this paper, we present a comparative analysis of transient fault tolerant techniques including end-to-end, node-by-node, and stochastic communication based on flooding principle.
Abstract: When a small H/W IP is designed, we can develop an
appropriate verification environment by observing the simulated
signal waves, or using the serial test vectors for the fixed output. In the
case of design and verification of a massive parallel processor with
multiple IPs, it-s difficult to make a verification system with existing
common verification environment, and to verify each partial IP. A
TestDrive verification environment can build easy and reliable
verification system that can produce highly intuitive results by
applying Modelsim and SystemVerilog-s DPI. It shows many
advantages, for example a high-level design of a GPGPU processor
design can be migrate to FPGA board immediately.
Abstract: Most of ignition delay correlations studies have been
developed in a constant volume bombs which cannot capture the
dynamic variation in pressure and temperature during the ignition
delay as in real engines. Watson, Assanis et. al. and Hardenberg
and Hase correlations have been developed based on experimental
data of diesel engines. However, they showed limited predictive
ability of ignition delay when compared to experimental results. The
objective of the study was to investigate the dependency of ignition
delay time on engine brake power. An experimental investigation of
the effect of automotive diesel and water diesel emulsion fuels on
ignition delay under steady state conditions of a direct injection diesel
engine was conducted. A four cylinder, direct injection naturally
aspirated diesel engine was used in this experiment over a wide range
of engine speeds and two engine loads. The ignition delay
experimental data were compared with predictions of Assanis et. al.
and Watson ignition delay correlations. The results of the
experimental investigation were then used to develop a new ignition
delay correlation. The newly developed ignition delay correlation has
shown a better agreement with the experimental data than Assanis et.
al. and Watson when using automotive diesel and water diesel
emulsion fuels especially at low to medium engine speeds at both
loads. In addition, the second derivative of cylinder pressure which is
the most widely used method in determining the start of combustion
was investigated.
Abstract: This paper presents design and characterization of a
microaccelerometer designated for integration into cataract surgical
probe to detect hardness of different eye tissues during cataract
surgery. Soft posterior lens capsule of eye can be easily damaged in
comparison with hard opaque lens since the surgeon can not see
directly behind cutting needle during the surgery. Presence of
microsensor helps the surgeon to avoid rupturing posterior lens
capsule which if occurs leads to severe complications such as
glaucoma, infection, or even blindness. The microsensor having
overall dimensions of 480 μm x 395 μm is able to deliver significant
capacitance variations during encountered vibration situations which
makes it capable to distinguish between different types of tissue.
Integration of electronic components on chip ensures high level of
reliability and noise immunity while minimizes space and power
requirements. Physical characteristics and results on performance
testing, proves integration of microsensor as an effective tool to aid
the surgeon during this procedure.
Abstract: In order to find the particular interaction energy
between cylcloguanil and the amino acids surrounding the pocket of
wild type and quadruple mutant type PfDHFR enzymes, the MP2
method with basis set 6-31G(d,p) level of calculations was
performed. The obtained interaction energies found that Asp54 has
the strongest interaction energy to both wild type and mutant type of -
12.439 and -11.250 kcal/mol, respectively and three amino acids;
Asp54, Ile164 and Ile14 formed the H-bonding with cycloguanil
drug. Importantly, the mutation at Ser108Asn was the key important
of cycloguanil resistant with showing repulsive interaction energy.
Abstract: Full adders are important components in applications
such as digital signal processors (DSP) architectures and
microprocessors. In addition to its main task, which is adding two
numbers, it participates in many other useful operations such as
subtraction, multiplication, division,, address calculation,..etc. In
most of these systems the adder lies in the critical path that
determines the overall speed of the system. So enhancing the
performance of the 1-bit full adder cell (the building block of the
adder) is a significant goal.Demands for the low power VLSI have
been pushing the development of aggressive design methodologies to
reduce the power consumption drastically. To meet the growing
demand, we propose a new low power adder cell by sacrificing the
MOS Transistor count that reduces the serious threshold loss
problem, considerably increases the speed and decreases the power
when compared to the static energy recovery full (SERF) adder. So a
new improved 14T CMOS l-bit full adder cell is presented in this
paper. Results show 50% improvement in threshold loss problem,
45% improvement in speed and considerable power consumption
over the SERF adder and other different types of adders with
comparable performance.
Abstract: A topologically oriented neural network is very
efficient for real-time path planning for a mobile robot in changing
environments. When using a recurrent neural network for this
purpose and with the combination of the partial differential equation
of heat transfer and the distributed potential concept of the network,
the problem of obstacle avoidance of trajectory planning for a
moving robot can be efficiently solved. The related dimensional
network represents the state variables and the topology of the robot's
working space. In this paper two approaches to problem solution are
proposed. The first approach relies on the potential distribution of
attraction distributed around the moving target, acting as a unique
local extreme in the net, with the gradient of the state variables
directing the current flow toward the source of the potential heat. The
second approach considers two attractive and repulsive potential
sources to decrease the time of potential distribution. Computer
simulations have been carried out to interrogate the performance of
the proposed approaches.
Abstract: Electric vehicle (EV) is one of the effective solutions to
control emission of greenhouses gases in the world. It is of interest
for future transportation due to its sustainability and efficiency by
automotive manufacturers. Various electrical motors have been used
for propulsion system of electric vehicles in last decades. In this
paper brushed DC motor, Induction motor (IM), switched reluctance
motor (SRM) and brushless DC motor (BLDC) are simulated and
compared. BLDC motor is recommended for high performance
electric vehicles. PWM switching technique is implemented for speed
control of BLDC motor. Behavior of different modes of PWM speed
controller of BLDC motor are simulated in MATLAB/SIMULINK.
BLDC motor characteristics are compared and discussed for various
PWM switching modes under normal and inverter fault conditions.
Comparisons and discussions are verified through simulation results.
Abstract: The objective from this paper is to design a solar
thermal engine for space vehicles orbital control and electricity
generation. A computational model is developed for the prediction of
the solar thermal engine performance for different design parameters and conditions in order to enhance the engine efficiency. The engine is divided into two main subsystems. First, the concentrator dish
which receives solar energy from the sun and reflects them to the
cavity receiver. The second one is the cavity receiver which receives
the heat flux reflected from the concentrator and transfers heat to the
fluid passing over. Other subsystems depend on the application required from the engine. For thrust application, a nozzle is
introduced to the system for the fluid to expand and produce thrust.
Hydrogen is preferred as a working fluid in the thruster application.
Results model developed is used to determine the thrust for a
concentrator dish 4 meters in diameter (provides 10 kW of energy),
focusing solar energy to a 10 cm aperture diameter cavity receiver.
The cavity receiver outer length is 50 cm and the internal cavity is 47
cm in length. The suggested design material of the internal cavity is
tungsten to withstand high temperature. The thermal model and
analysis shows that the hydrogen temperature at the plenum reaches
2000oK after about 250 seconds for hot start operation for a flow rate
of 0.1 g/sec.Using solar thermal engine as an electricity generation
device on earth is also discussed. In this case a compressor and
turbine are used to convert the heat gained by the working fluid (air)
into mechanical power. This mechanical power can be converted into
electrical power by using a generator.
Abstract: Nanoemulsions are a class of emulsions with a droplet
size in the range of 50–500 nm and have attracted a great deal of
attention in recent years because it is unique characteristics. The
physicochemical properties of nanoemulsion suggests that it can be
successfully used to recover the residual oil which is trapped in the
fine pore of reservoir rock by capillary forces after primary and
secondary recovery. Oil-in-water nanoemulsion which can be formed
by high-energy emulsification techniques using specific surfactants
can reduce oil-water interfacial tension (IFT) by 3-4 orders of
magnitude. The present work is aimed on characterization of oil-inwater
nanoemulsion in terms of its phase behavior, morphological
studies; interfacial energy; ability to reduce the interfacial tension and
understanding the mechanisms of mobilization and displacement of
entrapped oil blobs by lowering interfacial tension both at the
macroscopic and microscopic level. In order to investigate the
efficiency of oil-water nanoemulsion in enhanced oil recovery
(EOR), experiments were performed to characterize the emulsion in
terms of their physicochemical properties and size distribution of the
dispersed oil droplet in water phase. Synthetic mineral oil and a series
of surfactants were used to prepare oil-in-water emulsions.
Characterization of emulsion shows that it follows pseudo-plastic
behaviour and drop size of dispersed oil phase follows lognormal
distribution. Flooding experiments were also carried out in a
sandpack system to evaluate the effectiveness of the nanoemulsion as
displacing fluid for enhanced oil recovery. Substantial additional
recoveries (more than 25% of original oil in place) over conventional
water flooding were obtained in the present investigation.
Abstract: The effect of concentration of reduction agent of
sodium borohydrate (NaBH4) on the properties of silicon
nanoparticles synthesized via microemulsion route is reported. In
this work, the concentration of the silicon tetrachloride (SiCl4) that
served as silicon source with sodium hydroxide (NaOH) and
polyethylene glycol (PEG) as stabilizer and surfactant, respectively,
are keep fixed. Four samples with varied concentration of NaBH4
from 0.05 M to 0.20 M were synthesized. It was found that the lowest
concentration of NaBH4 gave better formation of silicon
nanoparticles.
Abstract: We present an explicit expression to estimate driving voltage attenuation through RC networks representation of an ultrahigh- speed image sensor. Elmore delay metric for a fundamental RC chain is employed as the first-order approximation. By application of dimensional analysis to SPICE simulation data, we found a simple expression that significantly improves the accuracy of the approximation. Estimation error of the resultant expression for uniform RC networks is less than 2%. Similarly, another simple closed-form model to estimate 50 % delay through fundamental RC networks is also derived with sufficient accuracy. The framework of this analysis can be extended to address delay or attenuation issues of other VLSI structures.
Abstract: Some of the polycyclic aromatic hydrocarbons (PAHs)
are the strongest known carcinogens compounds; the majority of
them are mostly produced by the incomplete combustion of fossil
fuels; Motor vehicles are a significant source of polycyclic aromatic
hydrocarbon (PAH) where diesel emission is one of the main sources
of such compounds available in the ambient air. There is a big
concern about the increasing concentration of PAHs in the
environment. Researchers are trying to explore optimal methods to
reduce those pollutants and improve the quality of air. Water blended
fuel is one of the possible approaches to reduce emission of PAHs
from the combustion of diesel in urban and domestic vehicles. In this
work a modeling study was conducted using CHEMKIN-PRO
software to simulate spray combustion at similar diesel engine
conditions. Surrogate fuel of (80 % n-heptane and 20 % toluene) was
used due to detailed kinetic and thermodynamic data needed for
modeling is available for this kind of fuel but not available for diesel.
An emulsified fuel with 3, 5, 8, 10 and 20 % water by volume is used
as an engine feed for this study. The modeling results show that water
has a significant effect on reducing engine soot and PAHs precursors
formation up to certain extent.
Abstract: The paper presents an analytical solution for dispersion
of a solute in the peristaltic motion of a micropolar fluid in the
presence of magnetic field and both homogeneous and heterogeneous
chemical reactions. The average effective dispersion coefficient has
been found using Taylor-s limiting condition under long wavelength
approximation. The effects of various relevant parameters on the average
coefficient of dispersion have been studied. The average effective
dispersion coefficient increases with amplitude ratio, cross viscosity
coefficient and heterogeneous chemical reaction rate parameter. But it
decreases with magnetic field parameter and homogeneous chemical
reaction rate parameter. It can be noted that the presence of peristalsis
enhances dispersion of a solute.
Abstract: This study was designed to formulate,
pharmaceutically evaluate a topical skin-care cream (w/o emulsion)
of Aloe Vera versus its vehicle (Base) as control and determine their
effects on Stratum Corneum (SC) water content and Transepidermal
water loss (TEWL). Base containing no extract and a Formulation
containing 3% concentrated extract of Aloe Vera was developed by
entrapping in the inner aqueous phase of w/o emulsion (cream).
Lemon oil was incorporated to improve the odor. Both the Base and
Formulation were stored at 8°C ±0.1°C (in refrigerator), 25°C±0.1°C,
40°C±0.1°C and 40°C± 0.1°C with 75% RH (in incubator) for a
period of 4 weeks to predict their stability. The evaluation parameters
consisted of color, smell, type of emulsion, phase separation,
electrical conductivity, centrifugation, liquefaction and pH. Both the
Base and Formulation were applied to the cheeks of 21 healthy
human volunteers for a period of 8 weeks Stratum corneum (SC)
water content and Transepidermal water loss (TEWL) were
monitored every week to measure any effect produced by these
topical creams. The expected organoleptic stability of creams was
achieved from 4 weeks in-vitro study period. Odor was disappeared
with the passage of time due to volatilization of lemon oil. Both the
Base and Formulation produced significant (p≤0.05) changes in
TEWL with respect to time. SC water content was significantly
(p≤0.05) increased by the Formulation while the Base has
insignificant (p 0.05) effects on SC water content. The newly
formulated cream of Aloe Vera, applied is suitable for improvement
and quantitative monitoring of skin hydration level (SC water
content/ moisturizing effects) and reducing TEWL in people with dry
skin.
Abstract: In this paper, the criteria of Ψ-eventual stability have been established for generalized impulsive differential systems of multiple dependent variables. The sufficient conditions have been obtained using piecewise continuous Lyapunov function. An example is given to support our theoretical result.
Abstract: The objective of this research is parameters optimized
of the stair shape workpiece which is cut by CNC Wire-Cut EDM
(WEDW). The experiment material is SKD-11 steel of stair-shaped
with variable height workpiece 10, 20, 30 and 40 mm. with the same
10 mm. thickness are cut by Sodick's CNC Wire-Cut EDM model
AD325L.
The experiments are designed by 3k full factorial experimental
design at 3 level 2 factors and 9 experiments with 2 replicate. The
selected two factor are servo voltage (SV) and servo feed rate (SF)
and the response is cutting thickness error. The experiment is divided
in two experiments. The first experiment determines the significant
effective factor at confidential interval 95%. The SV factor is the
significant effective factor from first result. In order to result smallest
cutting thickness error of workpieces is 17 micron with the SV value
is 46 volt. Also show that the lower SV value, the smaller different
thickness error of workpiece. Then the second experiment is done to
reduce different cutting thickness error of workpiece as small as
possible by lower SV. The second experiment result show the
significant effective factor at confidential interval 95% is the SV
factor and the smallest cutting thickness error of workpieces reduce
to 11 micron with the experiment SV value is 36 volt.
Abstract: The present paper deals with problems related to the
possibilities to use fractal systems to solve some important scientific
and practical problems connected with filtering and separation of
aqueous phases from organic ones. For this purpose a special
separator have been designed. The reactor was filled with a porous
material with fractal dimension, which is an integral part of the set
for filtration and separation of emulsions. As a model emulsion
hexadecan mixture with water in equal quantities (1:1) was used. We
examined the hydrodynamics of the separation of the emulsion at
different rates of submission of the entrance of the reactor.
Abstract: Interaction effects of xanthan gum (XG), carboxymethyl
cellulose (CMC), and locust bean gum (LBG) on the flow properties
of oil-in-water emulsions were investigated by a mixture design
experiment. Blends of XG, CMC and LBG were prepared according
to an augmented simplex-centroid mixture design (10 points) and used
at 0.5% (wt/wt) in the emulsion formulations. An appropriate
mathematical model was fitted to express each response as a function
of the proportions of the blend components that are able to
empirically predict the response to any blend of combination of the
components. The synergistic interaction effect of the ternary
XG:CMC:LBG blends at approximately 33-67% XG levels was
shown to be much stronger than that of the binary XG:LBG blend at
50% XG level (p < 0.05). Nevertheless, an antagonistic interaction
effect became significant as CMC level in blends was more than 33%
(p < 0.05). Yield stress and apparent viscosity (at 10 s-1) responses
were successfully fitted with a special quartic model while flow
behaviour index and consistency coefficient were fitted with a full
quartic model (R2
adjusted ≥ 0.90). This study found that a mixture
design approach could serve as a valuable tool in better elucidating
and predicting the interaction effects beyond the conventional twocomponent
blends.