Abstract: This paper presents PSS (Power system stabilizer) design based on optimal fuzzy PID (OFPID). OFPID based PSS design is considered for single-machine power systems. The main motivation for this design is to stabilize or to control low-frequency oscillation on power systems. Firstly, describing the linear PID control then to combine this PID control with fuzzy logic control mechanism. Finally, Fuzzy PID parameters (Kp. Kd, KI, Kupd, Kui) are tuned by Genetic Algorthm (GA) to reach optimal global stability. The effectiveness of the proposed PSS in increasing the damping of system electromechanical oscillation is demonstrated in a one-machine-infinite-bus system
Abstract: Use of a sliding joint is an effective method to
decrease the stress in foundation structure where there is a horizontal
deformation of subsoil (areas afflicted with underground mining) or
horizontal deformation of a foundation structure (pre-stressed
foundations, creep, shrinkage, temperature deformation). A
convenient material for a sliding joint is a bitumen asphalt belt.
Experiments for different types of bitumen belts were undertaken at
the Faculty of Civil Engineering - VSB Technical University of
Ostrava in 2008. This year an extension of the 2008 experiments is in
progress and the shear resistance of a slide joint is being tested as a
function of temperature in a temperature controlled room. In this
paper experimental results of temperature dependant shear resistance
are presented. The result of the experiments should be the sliding
joint shear resistance as a function of deformation velocity and
temperature. This relationship is used for numerical analysis of
stress/strain relation between foundation structure and subsoil. Using
a rheological slide joint could lead to a decrease of the reinforcement
amount, and contribute to higher reliability of foundation structure
and thus enable design of more durable and sustainable building
structures.
Abstract: In this paper a simple terrain evaluation method for
hexapod robot is introduced. This method is based on feet coordinate
evaluation when all are on the ground. Depending on the feet
coordinate differences the local terrain evaluation is possible. Terrain
evaluation is necessary for right gait selection and/or body position
correction. For terrain roughness evaluation three planes are plotted:
two of them as definition points use opposite feet coordinates, third
coincides with the robot body plane. The leaning angle of body plane
is evaluated measuring gravity force using three-axis accelerometer.
Terrain roughness evaluation method is based on angle estimation
between normal vectors of these planes. Aim of this work is to
present a simple method for embedded robot controller, allowing to
find the best further movement settings.
Abstract: In this paper a comprehensive model of a fossil fueled
power plant (FFPP) is developed in order to evaluate the
performance of a newly designed turbine follower controller.
Considering the drawbacks of previous works, an overall model is
developed to minimize the error between each subsystem model
output and the experimental data obtained at the actual power plant.
The developed model is organized in two main subsystems namely;
Boiler and Turbine. Considering each FFPP subsystem
characteristics, different modeling approaches are developed. For
economizer, evaporator, superheater and reheater, first order models
are determined based on principles of mass and energy conservation.
Simulations verify the accuracy of the developed models. Due to the
nonlinear characteristics of attemperator, a new model, based on a
genetic-fuzzy systems utilizing Pittsburgh approach is developed
showing a promising performance vis-à-vis those derived with other
methods like ANFIS. The optimization constraints are handled
utilizing penalty functions. The effect of increasing the number of
rules and membership functions on the performance of the proposed
model is also studied and evaluated. The turbine model is developed
based on the equation of adiabatic expansion. Parameters of all
evaluated models are tuned by means of evolutionary algorithms.
Based on the developed model a fuzzy PI controller is developed. It
is then successfully implemented in the turbine follower control
strategy of the plant. In this control strategy instead of keeping
control parameters constant, they are adjusted on-line with regard to
the error and the error rate. It is shown that the response of the
system improves significantly. It is also shown that fuel consumption
decreases considerably.
Abstract: In this work, a new approach is proposed to control
the manipulators for Humanoid robot. The kinematics of the
manipulators in terms of joint positions, velocity, acceleration and
torque of each joint is computed using the Denavit Hardenberg (D-H)
notations. These variables are used to design the manipulator control
system, which has been proposed in this work. In view of supporting
the development of a controller, a simulation of the manipulator is
designed for Humanoid robot. This simulation is developed through
the use of the Virtual Reality Toolbox and Simulink in Matlab. The
Virtual Reality Toolbox in Matlab provides the interfacing and
controls to an environment which is developed based on the Virtual
Reality Modeling Language (VRML). Chains of bones were used to
represent the robot.
Abstract: Nowadays pharmaceutical care departments located in
hospitals are amongst the important pillars of the healthcare system.
The aim of this study was to evaluate quality of hospital drugstores
affiliated with Kermanshah University of Medical Sciences.
In this cross-sectional study a validated questionnaire was used.
The questionnaire was filled in by the one of the researchers in all
seventeen hospital drugstores located in the teaching and nonteaching
hospitals affiliated with Kermanshah University of Medical
Sciences. The results shows that in observed hospitals,24% of
pharmacy environments, 25% of pharmacy store and storage
conditions, 49% of storage procedure, 25% of ordering drugs and
supplies, 73% of receiving supplies (proper procedure are fallowed
for receiving supplies), 35% of receiving supplies (prompt action
taken if deterioration of drugs received is suspected), 23.35% of
drugs delivery to patients and finally 0% of stock cards are used for
proper inventory control have full compliance with standards.
Abstract: The major source of allergy in home is the house dust
mite (Dematophagoides farina, Dermatophagoides pteronyssinus)
causing allergic symptom include atopic dermatitis, asthma, perennial
rhinitis and even infant death syndrome.
Control of this mite species is dependent on the use of chemical
methods such as fumigation treatments with methylene bromide,
spraying with organophosphates such as pirimiphos-methyl, or
treatments with repellents such as DEET and benzyl benzoate.
Although effective, their repeated use for decades has sometimes
resulted in development of resistance and fostered environmental and
human health concerns. Both decomposing animal parts and the
protein that surrounds mite fecal pellets cause mite allergy. So it is
more effective to repel than to kill them because allergen is not living
house dust mite but dead body or fecal particles of house dust mite.
It is important to find out natural repellent material against house
dust mite to control them and reduce the allergic reactions. Plants may
be an alternative source for dust mite control because they contain a
range of bioactive chemicals.
The research objectives of this paper were to verify the acaricidal
and repellent effects of cinnamon essential oil and to find out it-s most
effective concentrations. We could find that cinnamon bark essential
oil was very effective material to control the house dust mite.
Furthermore, it could reduce chemical resistance and danger for
human health.
Abstract: This paper aims at numerically analysing the effect
of an active flow control (AFC) by a vortex generator jet (VGJ)
submerged in a boundary layer via Chimera Grids and Detached-
Eddy Simulation (DES). The performance of DES results are
judged against Reynolds-Averaged Navier-Stokes (RANS) and
compared with the experiments that showed an unsteady vortex
motion downstream of VGJ. Experimental results showed that
the mechanism of embedding logitudinal vortex structure in the
main stream flow is quite effective in increasing the near wall
momentum of separated aircraft wing. In order to simulate such
a flow configuration together with the VGJ, an efficient numerical
approach is required. This requirement is fulfilled by performing
the DES simulation over the flat plate using the DLR TAU Code.
The DES predictions identify the vortex region via smooth hybrid
length scale and predict the unsteady vortex motion observed in
the experiments. The DES results also showed that the sufficient
grid refinement in the vortex region resolves the turbulent scales
downstream of the VGJ, the spatial vortex core postion and nondimensional
momentum coefficient RVx .
Abstract: The aerodynamic stall control of a baseline 13-percent
thick NASA GA(W)-2 airfoil using a synthetic jet actuator (SJA) is
presented in this paper. Unsteady Reynolds-averaged Navier-Stokes
equations are solved on a hybrid grid using a commercial software to
simulate the effects of a synthetic jet actuator located at 13% of the
chord from the leading edge at a Reynolds number Re = 2.1x106 and
incidence angles from 16 to 22 degrees. The experimental data for the
pressure distribution at Re = 3x106 and aerodynamic coefficients at
Re = 2.1x106 (angle of attack varied from -16 to 22 degrees) without
SJA is compared with the computational fluid dynamic (CFD)
simulation as a baseline validation. A good agreement of the CFD
simulations is obtained for aerodynamic coefficients and pressure
distribution.
A working SJA has been integrated with the baseline airfoil and
initial focus is on the aerodynamic stall control at angles of attack
from 16 to 22 degrees. The results show a noticeable improvement in
the aerodynamic performance with increase in lift and decrease in
drag at these post stall regimes.
Abstract: The motion planning technique described in this paper has been developed to eliminate or reduce the residual vibrations of belt-driven rotary platforms, while maintaining unchanged the motion time and the total angular displacement of the platform. The proposed approach is based on a suitable choice of the motion command given to the servomotor that drives the mechanical device; this command is defined by some numerical coefficients which determine the shape of the displacement, velocity and acceleration profiles. Using a numerical optimization technique, these coefficients can be changed without altering the continuity conditions imposed on the displacement and its time derivatives at the initial and final time instants. The proposed technique can be easily and quickly implemented on an actual device, since it requires only a simple modification of the motion command profile mapped in the memory of the electronic motion controller.
Abstract: The aim of this study was to test whether the Attention
Networks Test (ANT) showed temporal decrements in performance.
Vigilance tasks typically show such decrements, which may reflect
impairments in executive control resulting from cognitive fatigue.
The ANT assesses executive control, as well as alerting and
orienting. Thus, it was hypothesized that ANT executive control
would deteriorate over time. Manipulations including task condition
(trial composition) and masking were included in the experimental
design in an attempt to increase performance decrements. However,
results showed that there is no temporal decrement on the ANT. The
roles of task demands, cognitive fatigue and participant motivation in
producing this result are discussed. The ANT may not be an effective
tool for investigating temporal decrement in attention.
Abstract: Agropyron cristatum L. Gaertn. is a native grass of
semiarid region in Iran which is quit resistant to cool and drought
climate and withstand heavy grazing. This species has close
phylogenetic relationship with Triticum and Hordeum. In this
research, the effect of seven different concentrations of growth
regulator 2,4-D on callus production and somatic embryogenesis of
A. cristatum was investigated on Murashige and Skoog medium. The
results showed that the rate of callus, embryo and neomorph were
highest in 1 mg L-1 2,4-D. Callus production was increased in 1 mg
L-1 2,4-D but dramatically decreased at 5.5 and 9 mg L-1 2,4-D. The
somatic embryos were observed at 1 and 4 mg L-1 2,4-D but matured
embryos and plantlet were only occurred at 1 mg L-1 2,4-D. There
were significant differences between 1 mg L-1 2,4-D and other
treatments for producing globular and torpedo embryos, plantlet,
rooted callus and number of roots (p
Abstract: Today technological process makes possible surface
control of producing parts which is needful for product quality
guarantee. Geometrical structure of part surface includes form,
proportion, accuracy to shape, accuracy to size, alignment and
surface topography (roughness, waviness, etc.). All these parameters
are dependence at technology, production machine parameters,
material properties, but also at human, etc. Every parameters
approves at total part accuracy, it is means at accuracy to shape. One
of the most important accuracy to shape element is roundness. This
paper will be deals by comparison of roughness deviations at
coordination measuring machines and at special single purpose
machines. Will describing measuring by discreet method
(discontinuous) and scanning method (continuous) at coordination
measuring machines and confrontation with reference method using
at single purpose machines.
Abstract: The OTOP Entrepreneurship that used to create
substantial source of income for local Thai communities are now in a
stage of exigent matters that required assistances from public sectors
due to over Entrepreneurship of duplicative ideas, unable to adjust
costs and prices, lack of innovation, and inadequate of quality
control. Moreover, there is a repetitive problem of middlemen who
constantly corner the OTOP market. Local OTOP producers become
easy preys since they do not know how to add more values, how to
create and maintain their own brand name, and how to create proper
packaging and labeling. The suggested solutions to local OTOP
producers are to adopt modern management techniques, to find
knowhow to add more values to products and to unravel other
marketing problems. The objectives of this research are to study the
prevalent OTOP products management and to discover direction to
manage OTOP products to enhance the effectiveness of OTOP
Entrepreneurship in Nonthaburi Province, Thailand. There were 113
participants in this study. The research tools can be divided into two
parts: First part is done by questionnaire to find responses of the
prevalent OTOP Entrepreneurship management. Second part is the
use of focus group which is conducted to encapsulate ideas and local
wisdom. Data analysis is performed by using frequency, percentage,
mean, and standard deviation as well as the synthesis of several small
group discussions. The findings reveal that 1) Business Resources:
the quality of product is most important and the marketing of product
is least important. 2) Business Management: Leadership is most
important and raw material planning is least important. 3) Business
Readiness: Communication is most important and packaging is least
important. 4) Support from public sector: Certified from the
government is most important and source of raw material is the least
important.
Abstract: The industrial process of the sugar cane crystallization produces a residual that still contains a lot of soluble sucrose and the objective of the factory is to improve its extraction. Therefore, there are substantial losses justifying the search for the optimization of the process. Crystallization process studied on the industrial site is based on the “three massecuites process". The third step of this process constitutes the final stage of exhaustion of the sucrose dissolved in the mother liquor. During the process of the third step of crystallization (Ccrystallization), the phase that is studied and whose control is to be improved, is the growing phase (crystal growth phase). The study of this process on the industrial site is a problem in its own. A control scheme is proposed to improve the standard PID control law used in the factory. An auto-tuning PID controller based on instantaneous linearization of a neural network is then proposed.
Abstract: Modeling of complex dynamic systems, which are
very complicated to establish mathematical models, requires new and
modern methodologies that will exploit the existing expert
knowledge, human experience and historical data. Fuzzy cognitive
maps are very suitable, simple, and powerful tools for simulation and
analysis of these kinds of dynamic systems. However, human experts
are subjective and can handle only relatively simple fuzzy cognitive
maps; therefore, there is a need of developing new approaches for an
automated generation of fuzzy cognitive maps using historical data.
In this study, a new learning algorithm, which is called Big Bang-Big
Crunch, is proposed for the first time in literature for an automated
generation of fuzzy cognitive maps from data. Two real-world
examples; namely a process control system and radiation therapy
process, and one synthetic model are used to emphasize the
effectiveness and usefulness of the proposed methodology.
Abstract: The experimental design was 4 x 5 factorial with three
replications in fully controlled research greenhouse in Department of
Soil Sciences and Plant Nutrition, Faculty of Agriculture, University
of Selcuk in the year of 2009. Determination of tolerant chickpea
genotypes to drought was made in the research. Additionally,
sophisticated effects of drought on plant growth and development,
biochemical and physical properties or physical defense mechanisms
were presented. According to the results, the primary genotypes were
Ilgın YP (0.0063 g/gh) for leaf water capacity, 22235 70.44(%) for
relative water content, 22159 (82.47%) for real water content,
22159 (5.03 mg/l) for chlorophyll a+b, Ilgın YP (125.89 nmol
H2O2.dak-1/ mg protein-1) for peroxidase, Yunak YP (769.67
unit/ mg protein-1) for superoxide dismutase, Seydişehir YP
(16.74 μg.TA-1) for proline, Gökçe (80.01 nmol H2O2.dak-1/ mg
protein-1) for catalase. Consequently, all the genotypes
increased their enzyme activity depending on the increasing of
drought stress consider with the effects of drought stress on leaf
enzyme activity. Chickpea genotypes are increasing enzyme
activity against to drought stress.
Abstract: In this paper, we describe a rule-based message passing method to support developing collaborative applications, in which multiple users share resources in distributed environments. Message communications of applications in collaborative environments tend to be very complex because of the necessity to manage context situations such as sharing events, access controlling of users, and network places. In this paper, we propose a message communications method based on unification of artificial intelligence and logic programming for defining rules of such context information in a procedural object-oriented programming language. We also present an implementation of the method as java classes.
Abstract: Using strength Pulse Electrical Field (PEF) in food
industries is a non-thermal process that can deactivate
microorganisms and increase penetration in plant and animals tissues
without serious impact on food taste and quality. In this paper designing and fabricating of a PEF generator has been presented. Pulse generation methods have been surveyed and the best of them
selected. The equipment by controller set can generate square pulse with adjustable parameters such as amplitude 1-5kV, frequency 0.1-10Hz, pulse width 10-100s, and duty cycle 0-100%. Setting the number of pulses, and presenting the output voltage and current
waveforms on the oscilloscope screen are another advantages of this
equipment. Finally, some food samples were tested that yielded the satisfactory results. PEF applying had considerable effects on potato, banana and purple cabbage. It caused increase Brix factor from 0.05
to 0.15 in potato solution. It is also so effective in extraction color material from purple cabbage. In the last experiment effects of PEF
voltages on color extraction of saffron scum were surveyed (about 6% increasing yield).
Abstract: The alternative technique for sterilization of culture
medium to replace autoclaving was carried out. For sterilization of
culture medium without autoclaving, some commercial pure essential
oils, bergamot oil, betel oil, cinnamon oil, lavender oil and turmeric
oil, were tested alone or in combinations with some disinfectants,
10% povidone-iodine and 2% iodine + 2.4% potassium iodide. Each
essential oil or combination was added to 25-mL Murashige and
Skoog (MS) medium before medium was solidified in a 120-mL
container, kept for 2 weeks before evaluating sterile conditions.
Treated media, supplemented with essential oils, were compared to
control medium, autoclaved at 121 degree Celsius for 15 min. In
vitro sterile conditions were found 20 – 100% from these treated
media compared to 100% sterile condition from autoclaved medium.
Treated media obtained 100% sterile conditions were chosen for
culturing chrysanthemum shoots. It was found that 10% povidoneiodine
in combination with cinnamon oil (3:1) and 2% iodine + 2.4%
potassium iodide in combination with lavender oil (1:3) at the
concentration of 36 3L/25 mL medium provided the promising
growth of shoot explants.