Abstract: This study was carried out to evaluate concentration
of micro minerals (Zn, Fe, Mn, Cu and Se) of forages and their
distribution in fiber fraction (neutral detergent fiber/NDF and acid
detergent fiber/ADF) in South Sumatra during dry and rainy seasons.
Seven species of commonly forages namely Axonopus compressus,
Panicum maximum, Pennisetum purpuphoides, Leucaena
leucocephala, Centrocema pubescens, Calopogonium mucunoides
and Acacia mangium were collected at native pasture during rainy
and dry seasons. The results showed that micro minerals
concentration of forages and their distribution in fiber fraction varied
among species and season. In general, concentration of micro
minerals was slightly higher in rainy season compared to dry season
either in grass or legumes forages. In grass, concentration of Fe and
Mn were above the critical level, while 33.3 %, 100 % and 16.7 % of
evaluated grass were deficient in Zn, Cu and Se. Data on legume
forages show that 75 % of legumes were deficient in Zn and Mn, 62.5
% deficient in Cu and 50 % deficient in Se. There was no species of
legume deficient in Fe. Distribution of micro minerals in NDF and
ADF were also significantly affected by species and season and
depends on the kinds of element measured. Generally, micro minerals
were associated in fiber fractions much higher during dry season
compared to rainy season. Iron (Fe) and selenium (Se) in forages
were the highest elements associated in NDF and ADF, while the
lowest was found in Copper (Cu).
Abstract: Reinforced concrete stair slabs with mid landings i.e.
Dog-legged shaped are conventionally designed as per specifications
of standard codes of practices which guide about the effective span
according to the varying support conditions. Presently, the behavior
of such slabs has been investigated using Finite Element method. A
single flight stair slab with landings on both sides and supported at
ends on wall, and a multi flight stair slab with landings and six
different support arrangements have been analyzed. The results
obtained for stresses, strains and deflections are used to describe the
behavior of such stair slabs, including locations of critical moments
and deflections. Values of critical moments obtained by F.E. analysis
have also have been compared with that obtained from conventional
analysis. Analytical results show that the moments are also critical
near the kinks i.e. junction of mid-landing and inclined waist slab.
This change in the behavior of dog-legged stair slab may be due to
continuity of the material in transverse direction in two landings
adjoining the waist slab, hence additional stiffness achieved. This
change in the behavior is generally not taken care of in conventional
method of design.
Abstract: Face Recognition is a field of multidimensional
applications. A lot of work has been done, extensively on the most of
details related to face recognition. This idea of face recognition using
PCA is one of them. In this paper the PCA features for Feature
extraction are used and matching is done for the face under
consideration with the test image using Eigen face coefficients. The
crux of the work lies in optimizing Euclidean distance and paving the
way to test the same algorithm using Matlab which is an efficient tool
having powerful user interface along with simplicity in representing
complex images.
Abstract: This research evaluated and compared the thermodynamic performance of heat pump systems which can be run under two different modes as air to air and air to water by using only one compressor. To achieve this comparison an experimental performance study was made on a traditional vapor compressed heat pump system that can be run air to air mode and air to water mode by help of a valve. The experiments made under different thermal conditions. Thermodynamic performance of the systems are presented and compared with each other for different working conditions.
Abstract: Although achieving zero-defect software release is
practically impossible, software industries should take maximum
care to detect defects/bugs well ahead in time allowing only bare
minimums to creep into released version. This is a clear indicator of
time playing an important role in the bug detection. In addition to
this, software quality is the major factor in software engineering
process. Moreover, early detection can be achieved only through
static code analysis as opposed to conventional testing.
BugCatcher.Net is a static analysis tool, which detects bugs in .NET®
languages through MSIL (Microsoft Intermediate Language)
inspection. The tool utilizes a Parser based on Finite State Automata
to carry out bug detection. After being detected, bugs need to be
corrected immediately. BugCatcher.Net facilitates correction, by
proposing a corrective solution for reported warnings/bugs to end
users with minimum side effects. Moreover, the tool is also capable
of analyzing the bug trend of a program under inspection.
Abstract: Designing modern machine tools is a complex task. A
simulation tool to aid the design work, a virtual machine, has
therefore been developed in earlier work. The virtual machine
considers the interaction between the mechanics of the machine
(including structural flexibility) and the control system. This paper
exemplifies the usefulness of the virtual machine as a tool for product
development. An optimisation study is conducted aiming at
improving the existing design of a machine tool regarding weight and
manufacturing accuracy at maintained manufacturing speed. The
problem can be categorised as constrained multidisciplinary multiobjective
multivariable optimisation. Parameters of the control and
geometric quantities of the machine are used as design variables. This
results in a mix of continuous and discrete variables and an
optimisation approach using a genetic algorithm is therefore
deployed. The accuracy objective is evaluated according to
international standards. The complete systems model shows nondeterministic
behaviour. A strategy to handle this based on statistical
analysis is suggested. The weight of the main moving parts is reduced
by more than 30 per cent and the manufacturing accuracy is
improvement by more than 60 per cent compared to the original
design, with no reduction in manufacturing speed. It is also shown
that interaction effects exist between the mechanics and the control,
i.e. this improvement would most likely not been possible with a
conventional sequential design approach within the same time, cost
and general resource frame. This indicates the potential of the virtual
machine concept for contributing to improved efficiency of both
complex products and the development process for such products.
Companies incorporating such advanced simulation tools in their
product development could thus improve its own competitiveness as
well as contribute to improved resource efficiency of society at large.
Abstract: This paper uses the radial basis function neural
network (RBFNN) for system identification of nonlinear systems.
Five nonlinear systems are used to examine the activity of RBFNN in
system modeling of nonlinear systems; the five nonlinear systems are
dual tank system, single tank system, DC motor system, and two
academic models. The feed forward method is considered in this
work for modelling the non-linear dynamic models, where the KMeans
clustering algorithm used in this paper to select the centers of
radial basis function network, because it is reliable, offers fast
convergence and can handle large data sets. The least mean square
method is used to adjust the weights to the output layer, and
Euclidean distance method used to measure the width of the Gaussian
function.
Abstract: The purposes of this research were 1) to investigate
behavior of media exposure and participation in environmental
activities of King Mongkut-s University of Technology Thonburi
(KMUTT) dormitory students, 2) to compare the correlation between
faculties and participation in environmental activities of KMUTT
dormitory students, and 3) to compare the correlation between media
exposure and participation in environmental activities of KMUTT
dormitory students. The tool used for collecting data was
questionnaire. The research findings revealed that dormitory students
were mostly exposed to the environmental media via public relations
boards for general media and KMUTT dormitory media. Dormitory
students were daily exposed to media via websites on the internet and
weekly for other media. Dormitory students participation in the
environmental activities was at high level (x = 3.65) on an
individual basis and was at medium level (x = 2.76) on a collective
basis. Faculties did not correlate with the participation in
environmental activities of dormitory students at the .01 statistical
level and media exposure via various media correlated with
participation in environmental activities of dormitory students at the
.01 statistical level.
Abstract: The present work presents the extraction of copper(II)
from sulphuric acid solutions with Sodium diethyldithiocarbamate
(SDDT), and six different organic diluents: Dichloromethane,
Chloroform, Carbon tetrachloride, Toluene, xylene and Cyclohexane,
were tested. The pair SDDT/Chloroform showed to be the most
selective in removing the copper cations, and hence was considered
throughout the experimental study.
The effects of operating parameters such as the initial concentration
of the extracting agent, the agitation time, the agitation speed and the
acid concentration were considered.
For an initial concentration of Cu (II) of 63 ppm in a 0.5 M sulphuric
acid solution, both with a mass of the extracting agent of 20 mg, an
extraction percentage of about 97.8 % and a distribution coefficient
of 44.42 were obtained, respectively, confirming the performance
of the SDDT-Chloroform pair.
Abstract: Biochemical investigations were carried out to assess
the effect of different exposure regimes of Kazakhstan crude oil
(KCO) on hepatic antioxidant defense system in albino rats.
Contaminants were delivered under two different dosing regimes,
with all treatments receiving the same total contaminant load by the
end of the exposure period. Rats in regime A injected with KCO
once at a dose of 6 ml/kg bw while in regime B injected multiply at a
dose of 1.5 ml/kg bw on day 1, 3, 5 and 8. Antioxidant biomarkers
were measured in hepatic tissue after 1, 3, 5 and 8 days. Significant
induction was observed in serum aminotransferases (ALT, AST)
(p
Abstract: This paper demonstrates the feasibility of replacing
the metal coil spring with the composite coil spring. Three different
types of springs were made using glass fiber, carbon fiber and
combination of glass fiber and carbon fiber. The objective of the
study is to reduce the weight of the spring. According to the
experimental results the spring rate of the carbon fiber spring is
34% more than the glass fiber spring and 45% more than the glass
fiber/carbon fiber spring. The weight of the carbon fiber spring is
18% less than the glass fiber spring, 15% less than the Glass
fiber/carbon fiber spring and 80% less than the steel spring.
Abstract: In this paper, the strength of a stabilizer is determined when the static and fatigue multiaxial loading are applied. Stabilizer is a part of suspension system in the heavy truck for stabilizing the cabin against the vibration of the road which composes of a thin-walled tube joined to a forge component by fillet weld. The component is loaded by non proportional random sequence of torsion and bending. Residual stress of welding process is considered here for static loading. This static loading with road irregularities are applied in this study as fatigue case that can affected in the fillet welded area of this part. The stresses in the welded structure are calculated using FEA. In addition, the fatigue with multi axial loading in the fillet weld is also investigated and the critical zone of the stabilizer is specified and presented by graphs. Residual stresses that have been resulted by the thermal forces are considered in FEA. Force increasing is the element of finding the critical point of the component.
Abstract: In this paper, the processing of sonar signals has been
carried out using Minimal Resource Allocation Network (MRAN)
and a Probabilistic Neural Network (PNN) in differentiation of
commonly encountered features in indoor environments. The
stability-plasticity behaviors of both networks have been
investigated. The experimental result shows that MRAN possesses
lower network complexity but experiences higher plasticity than
PNN. An enhanced version called parallel MRAN (pMRAN) is
proposed to solve this problem and is proven to be stable in
prediction and also outperformed the original MRAN.
Abstract: CFlow is a flow chart software, it contains facilities to
draw and evaluate a flow chart. A flow chart evaluation applies a
simulation method to enable presentation of work flow in a flow
chart solution. Flow chart simulation of CFlow is executed by
manipulating the CFlow data file which is saved in a graphical vector
format. These text-based data are organised by using a data
classification technic based on a Library classification-scheme. This
paper describes the file format for flow chart simulation software of
CFlow.
Abstract: Unlike general-purpose processors, digital signal
processors (DSP processors) are strongly application-dependent. To
meet the needs for diverse applications, a wide variety of DSP
processors based on different architectures ranging from the
traditional to VLIW have been introduced to the market over the
years. The functionality, performance, and cost of these processors
vary over a wide range. In order to select a processor that meets the
design criteria for an application, processor performance is usually
the major concern for digital signal processing (DSP) application
developers. Performance data are also essential for the designers of
DSP processors to improve their design. Consequently, several DSP
performance benchmarks have been proposed over the past decade or
so. However, none of these benchmarks seem to have included recent
new DSP applications.
In this paper, we use a new benchmark that we recently developed
to compare the performance of popular DSP processors from Texas
Instruments and StarCore. The new benchmark is based on the
Selectable Mode Vocoder (SMV), a speech-coding program from the
recent third generation (3G) wireless voice applications. All
benchmark kernels are compiled by the compilers of the respective
DSP processors and run on their simulators. Weighted arithmetic
mean of clock cycles and arithmetic mean of code size are used to
compare the performance of five DSP processors.
In addition, we studied how the performance of a processor is
affected by code structure, features of processor architecture and
optimization of compiler. The extensive experimental data gathered,
analyzed, and presented in this paper should be helpful for DSP
processor and compiler designers to meet their specific design goals.
Abstract: The purpose of this study was to survey the effect of
organizational communication system on the conflict in physical
education offices of Isfahan province. The research methodology of
this research was a descriptive study. All employees working in
physical education offices of Isfahan province were included in the
sample for this study (N= 236). Researcher made questionnaire and
demographic questionnaire were used as investigation instruments.
Based on the result of chi square test, there is significant difference
between organizational communication system and interpersonal
conflict. The most of participants evaluate communication in an
informal way and pointed out that the communication channels were
not open. Based on the result of binomial test, interpersonal conflict
exists in physical education offices of Isfahan.
Abstract: Previous studies have indicated that one of the most
critical failure reasons of enterprise systems is the lack of knowledge
sharing and utilization across organizations. As a consequence, many
information systems researchers have paid attention to examining the
effect of absorptive capacity closely associated with knowledge
sharing and transferring on IS usage performance. A lack of
communications and interactions due to a lack of organizational
citizenship behavior might lead to weak absorptive capacity and thus
negatively influence knowledge sharing across organizations. In this
study, a theoretical model which delves into the relationship between
usage performance of enterprise systems and its determinants was
established.
Abstract: Based on the standard finite element method, a new
finite element method which is known as nonlocal finite element
method (NL-FEM) is numerically implemented in this article to
study the nonlocal effects for solving 1D nonlocal elastic problem.
An Eringen-type nonlocal elastic model is considered. In this model,
the constitutive stress-strain law is expressed interms of integral
equation which governs the nonlocal material behavior. The new
NL-FEM is adopted in such a way that the postulated nonlocal elastic
behavior of material is captured by a finite element endowed with a
set of (cross-stiffness) element itself by the other elements in mesh.
An example with their analytical solutions and the relevant numerical
findings for various load and boundary conditions are presented and
discussed in details. It is observed from the numerical solutions that
the torsional deformation angle decreases with increasing nonlocal
nanoscale parameter. It is also noted that the analytical solution fails
to capture the nonlocal effect in some cases where numerical
solutions handle those situation effectively which prove the
reliability and effectiveness of numerical techniques.
Abstract: Artemia is one of the most conspicuous invertebrates
associated with aquaculture. It can be considered as a model
organism, offering numerous advantages for comprehensive and
multidisciplinary studies using morphologic or molecular methods.
Since DNA extraction is an important step of any molecular
experiment, a new and a rapid method of DNA extraction from adult
Artemia was described in this study. Besides, the efficiency of this
technique was compared with two widely used alternative techniques,
namely Chelex® 100 resin and SDS-chloroform methods. Data
analysis revealed that the new method is the easiest and the most cost
effective method among the other methods which allows a quick and
efficient extraction of DNA from the adult animal.
Abstract: In the present paper, we-ll explore how social media tools provide an opportunity for new developments of the e-Learning in the context of managing personal knowledge. There will be a discussion how social media tools provide a possibility for helping knowledge workersand students to gather, organize and manage their personal information as a part of the e-learning process. At the centre of this social software driven approach to e-learning environments are the challenges of personalization and collaboration. We-ll share concepts of how organizations are using social media for e-Learning and believe that integration of these tools into traditional e-Learning is probably not a choice, but inevitability. Students- Survey of use of web technologies and social networking tools is presented. Newly developed framework for semantic blogging capable of organizing results relevant to user requirements is implemented at Varna Free University (VFU) to provide more effective navigation and search.