Abstract: In this study the integration of an absorption heat
pump (AHP) with the concentration section of an industrial pulp and
paper process is investigated using pinch technology. The optimum
design of the proposed water-lithium bromide AHP is then achieved
by minimizing the total annual cost. A comprehensive optimization is
carried out by relaxation of all stream pressure drops as well as heat
exchanger areas involving in AHP structure. It is shown that by
applying genetic algorithm optimizer, the total annual cost of the
proposed AHP is decreased by 18% compared to one resulted from
simulation.
Abstract: This paper describes a low-power second-order filter
for a continuous-time chopper stabilized capacitive sensor interface,
integrated with a fully differential post-CMOS surface-micromachined
MEMS pressure sensor. The circuit uses a single-ended
folded-cascode operational amplifier and two GM-C filters connected
in cascade. The circuit is realized in a 0.18 μm CMOS process and
offers differential to single-ended conversion. The novelty of the
scheme is the cascade of two GM-C filters to achieve a second-order
filter while minimizing power dissipation. The simulated filter cutoff
frequency is 1.14 kHz at common-mode voltage 1.65 V,
operating from a 3.3 V supply while dissipating 172μW of power.
The filter achieves an operating range of 1V for an output load of
1MOhm and 10pF.
Abstract: Knowledge management (KM) is generally
considered to be a positive process in an organisation, facilitating
opportunities to achieve competitive advantage via better quality
information handling, compilation of expert know-how and rapid
response to fluctuations in the business environment. The KM
paradigm as portrayed in the literature informs the processes that can
increase intangible assets so that corporate knowledge is preserved.
However, in some instances, knowledge management exists in a
universe of dynamic tension among the conflicting needs to respect
privacy and intellectual property (IP), to guard against data theft, to
protect national security and to stay within the laws. While the
Knowledge Management literature focuses on the bright side of the
paradigm, there is also a different side in which knowledge is
distorted, suppressed or misappropriated due to personal or
organisational motives (the paradox). This paper describes the ethical
paradoxes that occur within the taxonomy and deontology of
knowledge management and suggests that recognising both the
promises and pitfalls of KM requires wisdom.
Abstract: In this paper, we consider the analysis of the
acquisition process for a hybrid double-dwell system with antenna
diversity for DS-CDMA (direct sequence-code division multiple
access) using an adaptive threshold. Acquisition systems with a fixed
threshold value are unable to adapt to fast varying mobile
communications environments and may result in a high false alarm
rate, and/or low detection probability. Therefore, we propose an
adaptively varying threshold scheme through the use of a cellaveraging
constant false alarm rate (CA-CFAR) algorithm, which is
well known in the field of radar detection. We derive exact
expressions for the probabilities of detection and false alarm in
Rayleigh fading channels. The mean acquisition time of the system
under consideration is also derived. The performance of the system is
analyzed and compared to that of a hybrid single dwell system.
Abstract: Viscous heating becomes significant in the high speed
resin coating process of glass fibers for optical fiber manufacturing.
This study focuses on the coating resin flows inside the capillary
coating die of optical fiber coating applicator and they are numerically
simulated to examine the effects of viscous heating and subsequent
temperature increase in coating resin. Resin flows are driven by fast
moving glass fiber and the pressurization at the coating die inlet, while
the temperature dependent viscosity of liquid coating resin plays an
important role in the resin flow. It is found that the severe viscous
heating near the coating die wall profoundly alters the radial velocity
profiles and that the increase of final coating thickness by die
pressurization is amplified if viscous heating is present.
Abstract: In this paper, the application of thermal spray
coatings in high speed shafts by a revolution up to 23000 RPM
has been studied. Gas compressor shafts are worn in contact
zone with journal therefore will be undersized. Wear
mechanisms of compressor shaft were identified. The
predominant wear mechanism is abrasion wear. The worn
surface was coated by hard WC-Co cermets using high
velocity oxy fuel (HVOF) after preparation. The shafts were in
satisfactory service in 8000h period. The metallurgical and
Tribological studies has been made on the worn and coated
shaft using optical microscopy, scanning electron microscopy
(SEM) and X-ray diffraction.
Abstract: Pressure waves and Water Hammer occur in a
pumping system when valves are closed or opened suddenly or in
the case of sudden failure of pumps. Determination of maximum
water hammer is considered one of the most important technical
and economical items of which engineers and designers of
pumping stations and conveyance pipelines should take care.
Hammer Software is a recent application used to simulate water
hammer. The present study focuses on determining significance of
each input parameter of the application relative to the maximum
amount of water hammer estimated by the software. The study
determines estimated maximum water hammer variations due to
variations of input parameters including water temperature, pipe
type, thickness and diameter, electromotor rpm and power, and
moment of inertia of electromotor and pump. In our study,
Kuhrang Pumping Station was modeled using WaterGEMS
Software. The pumping station is characterized by total discharge
of 200 liters per second, dynamic height of 194 meters and 1.5
kilometers of steel conveyance pipeline and transports water to
Cheshme Morvarid for farmland irrigation. The model was run in
steady hydraulic condition and transferred to Hammer Software.
Then, the model was run in several unsteady hydraulic conditions
and sensitivity of maximum water hammer to each input parameter
was calculated. It is shown that parameters to which maximum
water hammer is most sensitive are moment of inertia of pump and
electromotor, diameter, type and thickness of pipe and water
temperature, respectively.
Abstract: This paper presents an analysis on the capacity and performance of MIMO-OFDM systems. The work is focused on the capacity of MIMO-OFDM systems over rician fading channel, in the case of the channel being known at the receiver only, which is more practical case of the channel. Simple expression for capacity is derived for the case of correlated rician fading. The performance of some MIMO-OFDM implementations with rician fading model is presented using an Alamouti coding scheme and Simulation results are obtained for both capacity and performance analysis.
Abstract: As a vital activity for companies, new product
development (NPD) is also a very risky process due to the high
uncertainty degree encountered at every development stage and the
inevitable dependence on how previous steps are successfully
accomplished. Hence, there is an apparent need to evaluate new
product initiatives systematically and make accurate decisions under
uncertainty. Another major concern is the time pressure to launch a
significant number of new products to preserve and increase the
competitive power of the company. In this work, we propose an
integrated decision-making framework based on neural networks and
fuzzy logic to make appropriate decisions and accelerate the
evaluation process. We are especially interested in the two initial
stages where new product ideas are selected (go/no go decision) and
the implementation order of the corresponding projects are
determined. We show that this two-staged intelligent approach allows
practitioners to roughly and quickly separate good and bad product
ideas by making use of previous experiences, and then, analyze a
more shortened list rigorously.
Abstract: Natural gas usually includes H2S component which is
very toxic, hazardous and corrosive to environment, human being and
process equipments, respectively. Therefore, sweetening of the gas
(separation of H2S) is inevitable. To achieve this purpose, using
packed-bed columns with liquid absorbents such as MEA or DEA is
very common. Due to some problems of usual packed columns
especially high pressure drop of gas phase, a novel kind of them
called wetted-wire column (WWC) has been invented. The column
decreases the pressure drop significantly and improves the absorption
efficiency. The packings are very thin rods (like wire) and as long as
column. The column has 100 wires with a triangular arrangement and
counter current flows of gas and liquid phases. The observation
showed that at the same conditions, the absorption performance was
quite comparable to conventional packed-bed towers and a very low
pressure drop.
Abstract: This paper details a new concept of using compressed air as a potential zero pollution power source for motorbikes. In place of an internal combustion engine, the motorbike is equipped with an air turbine transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor diameters, casing diameters and ratio of rotor to casing diameters of the turbine have been considered and analyzed. It is concluded that the work output is found optimum for some typical values of rotor / casing diameter ratios. In this study, the maximum power works out to 3.825 kW (5.20 HP) for casing diameter of 200 mm and rotor to casing diameter ratio of 0.65 to 0.60 which is sufficient to run motorbike.
Abstract: In this work, we present a comparison between
different techniques of image compression. First, the image is
divided in blocks which are organized according to a certain scan.
Later, several compression techniques are applied, combined or
alone. Such techniques are: wavelets (Haar's basis), Karhunen-Loève
Transform, etc. Simulations show that the combined versions are the
best, with minor Mean Squared Error (MSE), and higher Peak Signal
to Noise Ratio (PSNR) and better image quality, even in the presence
of noise.
Abstract: The main objective of this paper is to provide an efficient tool for delineating brain tumors in three-dimensional magnetic resonance images. To achieve this goal, we use basically a level-sets approach to delineating three-dimensional brain tumors. Then we introduce a compression plan of 3D brain structures based for the meshes simplification, adapted for time to the specific needs of the telemedicine and to the capacities restricted by network communication. We present here the main stages of our system, and preliminary results which are very encouraging for clinical practice.
Abstract: This study was aimed to study the probability about
the production of fiberboard made of durian rind through latex with
phenolic resin as binding agent. The durian rind underwent the
boiling process with NaOH [7], [8] and then the fiber from durian
rind was formed into fiberboard through heat press. This means that
durian rind could be used as replacement for plywood in plywood
industry by using durian fiber as composite material with adhesive
substance. This research would study the probability about the
production of fiberboard made of durian rind through latex with
phenolic resin as binding agent. At first, durian rind was split,
exposed to light, boiled and steamed in order to gain durian fiber.
Then, fiberboard was tested with the density of 600 Kg/m3 and 800
Kg/m3. in order to find a suitable ratio of durian fiber and latex.
Afterwards, mechanical properties were tested according to the
standards of ASTM and JIS A5905-1994. After the suitable ratio was
known, the test results would be compared with medium density
fiberboard (MDF) and other related research studies. According to
the results, fiberboard made of durian rind through latex with
phenolic resin at the density of 800 Kg/m3 at ratio of 1:1, the
moisture was measured to be 5.05% with specific gravity (ASTM D
2395-07a) of 0.81, density (JIS A 5905-1994) of 0.88 g/m3, tensile
strength, hardness (ASTM D2240), flexibility or elongation at break
yielded similar values as the ones by medium density fiberboard
(MDF).
Abstract: Iodine radionuclides in accident releases under severe
accident conditions at NPP with VVER are the most radiationimportant
with a view to population dose generation at the beginning
of the accident. To decrease radiation consequences of severe
accidents the technical solutions for severe accidents management
have been proposed in MIR.1200 project, with consideration of the
measures for suppression of volatile iodine forms generation in the
containment. Behavior dynamics of different iodine forms in the
containment under severe accident conditions has been analyzed for
the purpose of these technical solutions justification.
Abstract: In this paper, the dam-reservoir interaction is
analyzed using a finite element approach. The fluid is assumed to be
incompressible, irrotational and inviscid. The assumed boundary
conditions are that the interface of the dam and reservoir is vertical
and the bottom of reservoir is rigid and horizontal. The governing
equation for these boundary conditions is implemented in the
developed finite element code considering the horizontal and vertical
earthquake components. The weighted residual standard Galerkin
finite element technique with 8-node elements is used to discretize
the equation that produces a symmetric matrix equation for the damreservoir
system. A new boundary condition is proposed for
truncating surface of unbounded fluid domain to show the energy
dissipation in the reservoir, through radiation in the infinite upstream
direction. The Sommerfeld-s and perfect damping boundary
conditions are also implemented for a truncated boundary to compare
with the proposed far end boundary. The results are compared with
an analytical solution to demonstrate the accuracy of the proposed
formulation and other truncated boundary conditions in modeling the
hydrodynamic response of an infinite reservoir.
Abstract: The Malaysia Highway Authority (MHA) was
established by the Government in 1980 for the purpose of designing,
constructing and maintaining toll highways in Malaysia that include
the North-South Expressway and the Penang Bridge, which were
procured using the publicly-funded traditional procurement. However
following a recession in the mid 80-s, the operations of these tolledhighways
had been privatized to ensure that their operational services
continue through private financing as a result of long-term
concession agreement concurred between the Malaysian Government
and private operators. The change in the contract strategy for
highway projects in Malaysia would have a great tendency to dictate
a significant risk exposure towards the key parties involved,
particularly the Malaysian Government as project principal, unless
operational risks are clearly identified and managed via appropriate
mitigation measures prior to a contract signing.
This research identifies potential operational risks that have a
possibility to occur in highway projects in Malaysia from the
perspective of public sector clients. Since this research focuses on the
operational risks for highway projects in Malaysia, the initial results
acquired from literature review on the operational risks of highway
projects in some Asian countries are then justified by a number of
key individuals from the MHA through interviews. As a result,
among key operational risks that have possibility to occur in the
highway projects in Malaysia include initial toll-tariff decided by the
Government, traffic congestion, change of road network and overloaded
freight transportation, which could cause damage to the road
surface and hence affecting the operation of a particular highway.
Abstract: The aim of this paper is to investigate twodimensional unsteady flow of a viscous incompressible fluid about stagnation point on permeable stretching sheet in presence of time dependent free stream velocity. Fluid is considered in the influence of transverse magnetic field in the presence of radiation effect. Rosseland approximation is use to model the radiative heat transfer. Using time-dependent stream function, partial differential equations corresponding to the momentum and energy equations are converted into non-linear ordinary differential equations. Numerical solutions of these equations are obtained by using Runge-Kutta Fehlberg method with the help of Newton-Raphson shooting technique. In the present work the effect of unsteadiness parameter, magnetic field parameter, radiation parameter, stretching parameter and the Prandtl number on flow and heat transfer characteristics have been discussed. Skin-friction coefficient and Nusselt number at the sheet are computed and discussed. The results reported in the paper are in good agreement with published work in literature by other researchers.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: DNA microarray technology is widely used by
geneticists to diagnose or treat diseases through gene expression.
This technology is based on the hybridization of a tissue-s DNA
sequence into a substrate and the further analysis of the image
formed by the thousands of genes in the DNA as green, red or yellow
spots. The process of DNA microarray image analysis involves
finding the location of the spots and the quantification of the
expression level of these. In this paper, a tool to perform DNA
microarray image analysis is presented, including a spot addressing
method based on the image projections, the spot segmentation
through contour based segmentation and the extraction of relevant
information due to gene expression.