Abstract: Examining existing experimental results for shallow
rigid foundations subjected to vertical centric load (N), accompanied
or not with a bending moment (M), two main non-linear mechanisms
governing the cyclic response of the soil-foundation system can be
distinguished: foundation uplift and soil yielding. A soil-foundation
failure limit, is defined as a domain of resistance in the two
dimensional (2D) load space (N, M) inside of which lie all the
admissible combinations of loads; these latter correspond to a pure
elastic, non-linear elastic or plastic behavior of the soil-foundation
system, while the points lying on the failure limit correspond to a
combination of loads leading to a failure of the soil-foundation
system. In this study, the proposed resistance domain is constructed
analytically based on mechanics. Original elastic limit, uplift
initiation limit and iso-uplift limits are constructed inside this
domain. These limits give a prediction of the mechanisms activated
for each combination of loads applied to the foundation. A
comparison of the proposed failure limit with experimental tests
existing in the literature shows interesting results. Also, the
developed uplift initiation limit and iso-uplift curves are confronted
with others already proposed in the literature and widely used due to
the absence of other alternatives, and remarkable differences are
noted, showing evident errors in the past proposals and relevant
accuracy for those given in the present work.
Abstract: Wet scrubbers have found widespread use in cleaning
contaminated gas streams because of their ability to remove
particulates and based on the applications of scrubbing of marine
engine exhaust gases by spraying sea-water. In order to examine the
flow characteristics inside the scrubber, the model is designated with
flow properties of hot air and water sprayer. The flow dynamics of
evaporation of hot air by the injection of water droplets is the key
factor considered in this paper. The flow behavior inside the scrubber
was investigated from the previous works and to sum up the
evaporation rate with respect to the concentration of water droplets are
predicted to bring out the competent modelling. The numerical
analysis using CFD facilitates in understanding the problem better and
empathies the behavior of the model over its entire operating envelope.
Abstract: Passing the entrance exam to a university is a major
step in one's life. University entrance exam commonly known as
Kankor is the nationwide entrance exam in Afghanistan. This
examination is prerequisite for all public and private higher education
institutions at undergraduate level. It is usually taken by students who
are graduated from high schools. In this paper, we reflect the major
educational school graduates issues and propose ICT-based test
preparation environment, known as ‘Online Kankor Exam Prep
System’ to give students the tools to help them pass the university
entrance exam on the first try. The system is based on Intelligent
Tutoring System (ITS), which introduced an essential package of
educational technology for learners that features: (I) exam-focused
questions and content; (ii) self-assessment environment; and (iii) test
preparation strategies in order to help students to acquire the necessary
skills in their carrier and keep them up-to-date with instruction.
Abstract: This paper describes a novel application of Fiber
Braggs Grating (FBG) sensors in the assessment of human postural
stability and balance on an unstable platform. In this work, FBG
sensor Stability Analyzing Device (FBGSAD) is developed for
measurement of plantar strain to assess the postural stability of
subjects on unstable platforms during different stances in eyes open
and eyes closed conditions on a rocker board. The studies are
validated by comparing the Centre of Gravity (CG) variations
measured on the lumbar vertebra of subjects using a commercial
accelerometer. The results obtained from the developed FBGSAD
depict qualitative similarities with the data recorded by commercial
accelerometer. The advantage of the FBGSAD is that it measures
simultaneously plantar strain distribution and postural stability of the
subject along with its inherent benefits like non-requirement of
energizing voltage to the sensor, electromagnetic immunity and
simple design which suits its applicability in biomechanical
applications. The developed FBGSAD can serve as a tool/yardstick to
mitigate space motion sickness, identify individuals who are
susceptible to falls and to qualify subjects for balance and stability,
which are important factors in the selection of certain unique
professionals such as aircraft pilots, astronauts, cosmonauts etc.
Abstract: Nowadays, the successful implementation of ICTs is
vital for almost any kind of organization. Good governance and ICT
management are essential for delivering value, managing
technological risks, managing resources and performance
measurement. In addition, outsourcing is a strategic IT service
solution which complements IT services provided internally in
organizations. This paper proposes the measurement tools of a new
holistic maturity model based on standards ISO/IEC 20000 and
ISO/IEC 38500, and the frameworks and best practices of ITIL and
COBIT, with a specific focus on IT outsourcing. These measurement
tools allow independent validation and practical application in the
field of higher education, using a questionnaire, metrics tables, and
continuous improvement plan tables as part of the measurement
process. Guidelines and standards are proposed in the model for
facilitating adaptation to universities and achieving excellence in the
outsourcing of IT services.
Abstract: Factors affecting construction unit cost vary
depending on a country’s political, economic, social and
technological inclinations. Factors affecting construction costs have
been studied from various perspectives. Analysis of cost factors
requires an appreciation of a country’s practices. Identified cost
factors provide an indication of a country’s construction economic
strata. The purpose of this paper is to identify the essential factors
that affect unit cost estimation and their breakdown using artificial
neural networks. Twenty five (25) identified cost factors in road
construction were subjected to a questionnaire survey and employing
SPSS factor analysis the factors were reduced to eight. The 8 factors
were analysed using neural network (NN) to determine the
proportionate breakdown of the cost factors in a given construction
unit rate. NN predicted that political environment accounted 44% of
the unit rate followed by contractor capacity at 22% and financial
delays, project feasibility and overhead & profit each at 11%. Project
location, material availability and corruption perception index had
minimal impact on the unit cost from the training data provided.
Quantified cost factors can be incorporated in unit cost estimation
models (UCEM) to produce more accurate estimates. This can create
improvements in the cost estimation of infrastructure projects and
establish a benchmark standard to assist the process of alignment of
work practises and training of new staff, permitting the on-going
development of best practises in cost estimation to become more
effective.
Abstract: The thermal conductivity of a fluid can be
significantly enhanced by dispersing nano-sized particles in it, and
the resultant fluid is termed as "nanofluid". A theoretical model for
estimating the thermal conductivity of a nanofluid has been proposed
here. It is based on the mechanism that evenly dispersed
nanoparticles within a nanofluid undergo Brownian motion in course
of which the nanoparticles repeatedly collide with the heat source.
During each collision a rapid heat transfer occurs owing to the solidsolid
contact. Molecular dynamics (MD) simulation of the collision
of nanoparticles with the heat source has shown that there is a pulselike
pick up of heat by the nanoparticles within 20-100 ps, the extent
of which depends not only on thermal conductivity of the
nanoparticles, but also on the elastic and other physical properties of
the nanoparticle. After the collision the nanoparticles undergo
Brownian motion in the base fluid and release the excess heat to the
surrounding base fluid within 2-10 ms. The Brownian motion and
associated temperature variation of the nanoparticles have been
modeled by stochastic analysis. Repeated occurrence of these events
by the suspended nanoparticles significantly contributes to the
characteristic thermal conductivity of the nanofluids, which has been
estimated by the present model for a ethylene glycol based nanofluid
containing Cu-nanoparticles of size ranging from 8 to 20 nm, with
Gaussian size distribution. The prediction of the present model has
shown a reasonable agreement with the experimental data available
in literature.
Abstract: Developing young people’s employability is a key
policy issue for ensuring their successful transition to the labour
market and their access to career oriented employment. The youths of
today irrespective of their gender need to acquire the knowledge,
skills and attitudes that will enable them to create or find jobs as well
as cope with unpredictable labour market changes throughout their
working lives. In a study carried out to determine the influence of
gender on job-competencies requirements of chemical-based
industries and undergraduate-competencies acquisition by chemists
working in the industries, all chemistry graduates working in twenty
(20) chemical-based industries that were randomly selected from six
sectors of chemical-based industries in Lagos and Ogun States of
Nigeria were administered with Job-competencies required and
undergraduate-competencies acquired assessment questionnaire. The
data were analysed using means and independent sample t-test. The
findings revealed that the population of female chemists working in
chemical-based industries is low compared with the number of male
chemists; furthermore, job-competencies requirements are found not
to be gender biased while there is no significant difference in
undergraduate-competencies acquisition of male and female
chemists. This suggests that females should be given the same
opportunity of employment in chemical-based industries as their male
counterparts. The study also revealed the level of acquisition of
undergraduate competencies as related to the needs of chemicalbased
industries.
Abstract: In this study which has been conducted in Akçasu
Forest Range District of Devrek Forest Directorate; 3 methods (weed
control with labourer power, cover removal with Hitachi F20
Excavator, and weed control with agricultural equipment mounted on
a Ferguson 240S agriculture tractor) were utilized in weed control
efforts in regeneration of degraded oriental beech forests have been
compared. In this respect, 3 methods have been compared by
determining certain work hours and standard durations of unit areas
(1 hectare). For this purpose, evaluating the tasks made with human
and machine force from the aspects of duration, productivity and
costs, it has been aimed to determine the most productive method in
accordance with the actual ecological conditions of research field.
Within the scope of the study, the time studies have been conducted
for 3 methods used in weed control efforts. While carrying out those
studies, the performed implementations have been evaluated by
dividing them into business stages. Also, the actual data have been
used while calculating the cost accounts. In those calculations, the
latest formulas and equations which are also used in developed
countries have been utilized. The variance of analysis (ANOVA) was
used in order to determine whether there is any statistically
significant difference among obtained results, and the Duncan test
was used for grouping if there is significant difference. According to
the measurements and findings carried out within the scope of this
study, it has been found during living cover removal efforts in
regeneration efforts in demolished oriental beech forests that the
removal of weed layer in 1 hectare of field has taken 920 hours with
labourer force, 15.1 hours with excavator and 60 hours with an
equipment mounted on a tractor. On the other hand, it has been
determined that the cost of removal of living cover in unit area (1
hectare) was 3220.00 TL for labourer power, 1250 TL for excavator
and 1825 TL for equipment mounted on a tractor.
According to the obtained results, it has been found that the
utilization of excavator in weed control effort in regeneration of
degraded oriental beech regions under actual ecological conditions of
research field has been found to be more productive from both of
aspects of duration and costs. These determinations carried out
should be repeated in weed control efforts in degraded forest fields
with different ecological conditions, it is compulsory for finding the
most efficient weed control method. These findings will light the way
of technical staff of forestry directorate in determination of the most
effective and economic weed control method. Thus, the more actual
data will be used while preparing the weed control budgets, and there
will be significant contributions to national economy. Also the results of this and similar studies are very important for developing the policies for our forestry in short and long term.
Abstract: The recommended limit for cadmium concentration in
potable water is less than 0.005 mg/L. A continuous biosorption
process using indigenous red seaweed, Gracilaria corticata, was
performed to remove cadmium from the potable water. The process
was conducted under fixed conditions and the breakthrough curves
were achieved for three consecutive sorption-desorption cycles. A
modeling based on Artificial Neural Network (ANN) was employed
to fit the experimental breakthrough data. In addition, a simplified
semi empirical model, Thomas, was employed for this purpose. It
was found that ANN well described the experimental data (R2>0.99)
while the Thomas prediction were a bit less successful with R2>0.97.
The adjusted design parameters using the nonlinear form of Thomas
model was in a good agreement with the experimentally obtained
ones. The results approve the capability of ANN to predict the
cadmium concentration in potable water.
Abstract: Background: Taiwan now is an aging society. Research
on the elderly should not be confined to caring for seniors, but should
also be focused on ways to improve health and the quality of life.
Senior citizens who participate in volunteer services could become
less lonely, have new growth opportunities, and regain a sense of
accomplishment. Thus, the question of how to get the elderly to
participate in volunteer service is worth exploring. Objective: Apply
the Transtheoretical Model to understand stages of change in regular
volunteer service and voluntary service behaviour among the seniors.
Methods: 1525 adults over the age of 65 from the Renai district of
Keelung City were interviewed. The research tool was a
self-constructed questionnaire, and individual interviews were
conducted to collect data. Then the data was processed and analyzed
using the IBM SPSS Statistics 20 (Windows version) statistical
software program. Results: In the past six months, research subjects
averaged 9.92 days of volunteer services. A majority of these elderly
individuals had no intention to change their regular volunteer services.
We discovered that during the maintenance stage, the self-efficacy for
volunteer services was higher than during all other stages, but
self-perceived barriers were less during the preparation stage and
action stage. Self-perceived benefits were found to have an important
predictive power for those with regular volunteer service behaviors in
the previous stage, and self-efficacy was found to have an important
predictive power for those with regular volunteer service behaviors in
later stages. Conclusions/Implications for Practice: The research
results support the conclusion that community nursing staff should
group elders based on their regular volunteer services change stages
and design appropriate behavioral change strategies.
Abstract: Science and technology has a major impact on many
societal domains such as communication, medicine, food,
transportation, etc. However, this dominance of modern technology
can have a negative unintended impact on indigenous systems, and in
particular on indigenous foods. This problem serves as a motivation
to this study whose aim is to examine the perceptions of learners on
the usefulness of Information and Communication Technologies
(ICTs) for learning about indigenous foods. This aim will be
subdivided into two types of research objectives. The design and
identification of theories and models will be achieved using literature
content analysis. The objective on the empirical testing of such
theories and models will be achieved through the survey of
Hospitality studies learners from different schools in the iLembe and
Umgungundlovu Districts of the South African Kwazulu-Natal
province. SPSS is used to quantitatively analyze the data collected by
the questionnaire of this survey using descriptive statistics and
Pearson correlations after the assessment of the validity and the
reliability of the data. The main hypothesis behind this study is that
there is a connection between the demographics of learners, their
perceptions on the usefulness of ICTs for learning about indigenous
foods, and the following personality and eLearning related theories
constructs: Computer self-efficacy, Trust in ICT systems, and
Conscientiousness; as suggested by existing studies on learning
theories. This hypothesis was fully confirmed by the survey
conducted by this study except for the demographic factors where
gender and age were not found to be determinant factors of learners’
perceptions on the usefulness of ICTs for learning about indigenous
foods.
Abstract: At present, the evaluation of voltage stability
assessment experiences sizeable anxiety in the safe operation of
power systems. This is due to the complications of a strain power
system. With the snowballing of power demand by the consumers
and also the restricted amount of power sources, therefore, the system
has to perform at its maximum proficiency. Consequently, the
noteworthy to discover the maximum ability boundary prior to
voltage collapse should be undertaken. A preliminary warning can be
perceived to evade the interruption of power system’s capacity. The
effectiveness of line voltage stability indices (LVSI) is differentiated
in this paper. The main purpose of the indices used is to predict the
proximity of voltage instability of the electric power system. On the
other hand, the indices are also able to decide the weakest load buses
which are close to voltage collapse in the power system. The line
stability indices are assessed using the IEEE 14 bus test system to
validate its practicability. Results demonstrated that the implemented
indices are practically relevant in predicting the manifestation of
voltage collapse in the system. Therefore, essential actions can be
taken to dodge the incident from arising.
Abstract: Knowledge management is considered as an important
factor in improving health care services. KM facilitates the transfer of
existing knowledge and the development of new knowledge in
hospitals. This paper reviews practices adopted by doctors in Kuwait
for capturing, sharing, and generating knowledge. It also discusses
the perceived impact of KM practices on performance of hospitals.
Based on a survey of 277 doctors, the study found that KM practices
among doctors in the sampled hospitals were not very effective. Little
attention was paid to the main activities that support the transfer of
expertise among doctors in hospitals. However, as predicted by
previous studies, good km practices were perceived by doctors to
have a positive impact on performance of hospitals. It was concluded
that through effective KM practices hospitals could improve the
services they provide. Documentation of best practices and capturing
of lessons learnt for re-use of knowledge could help transform the
hospitals into learning organizations.
Abstract: Near infrared (NIR) spectroscopy has always been of
great interest in the food and agriculture industries. The development
of prediction models has facilitated the estimation process in recent
years. In this study, 110 crude palm oil (CPO) samples were used to
build a free fatty acid (FFA) prediction model. 60% of the collected
data were used for training purposes and the remaining 40% used for
testing. The visible peaks on the NIR spectrum were at 1725 nm and
1760 nm, indicating the existence of the first overtone of C-H bands.
Principal component regression (PCR) was applied to the data in
order to build this mathematical prediction model. The optimal
number of principal components was 10. The results showed
R2=0.7147 for the training set and R2=0.6404 for the testing set.
Abstract: This work was one of the tasks of the
Manufacturing2Client project, whose objective was to develop a
frontal deflector to be commercialized in the automotive industry,
using new project and manufacturing methods. In this task, in
particular, it was proposed to develop the ability to predict
computationally the aerodynamic influence of flow in vehicles, in an
effort to reduce fuel consumption in vehicles from class 3 to 8. With
this aim, two deflector models were developed and their aerodynamic
performance analyzed. The aerodynamic study was done using the
Computational Fluid Dynamics (CFD) software Ansys CFX and
allowed the calculation of the drag coefficient caused by the vehicle
motion for the different configurations considered. Moreover, the
reduction of diesel consumption and carbon dioxide (CO2) emissions
associated with the optimized deflector geometry could be assessed.
Abstract: Self-compacting concrete (SCC) developed in Japan
in the late 80s has enabled the construction industry to reduce
demand on the resources, improve the work condition and also
reduce the impact of environment by elimination of the need for
compaction. Fuzzy logic (FL) approaches has recently been used to
model some of the human activities in many areas of civil
engineering applications. Especially from these systems in the model
experimental studies, very good results have been obtained. In the
present study, a model for predicting compressive strength of SCC
containing various proportions of fly ash, as partial replacement of
cement has been developed by using Fuzzy Inference System (FIS).
For the purpose of building this model, a database of experimental
data were gathered from the literature and used for training and
testing the model. The used data as the inputs of fuzzy logic models
are arranged in a format of five parameters that cover the total binder
content, fly ash replacement percentage, water content,
superplasticizer and age of specimens. The training and testing results
in the fuzzy logic model have shown a strong potential for predicting
the compressive strength of SCC containing fly ash in the considered
range.
Abstract: The computational fluid dynamics (CFD) study of
stirred tank with the air-water interface are carried out in the presence
of different types of the impeller and with or without baffles. A
multiple reference frame (MRF) approach with the volume of fluid
(VOF) method is used to capture the air-water interface. The RANS
(Reynolds Averaged Navier-Stokes) equations with k-ε turbulence
model are solved to predict the flow behavior of water and air phase
which are treated as a different phases. The predicted results have
shown that the VOF method is able to capture the interface in the
unbaffled tank. While, the VOF method is showing an unfeasible
results in the baffled tank with high rotational impeller speed. For
continuous stirred tank, the air-water interface is disturbed by the
inflow and the level of water is also increased with time.
Abstract: Bamboo is extensively used in construction industry.
Low durability of bamboo due to fungus infestation and termites
attack under storage puts certain constrains for it usage as modern
structural material. Looking at many chemical formulations for
bamboo treatment leading to severe harmful environment effects,
research on eco-friendly preservatives for bamboo treatment has been
initiated world-over. In the present studies, eco-friendly preservative
for bamboo treatment has been developed. To validate its application
for structural purposes, investigation of effect of treatment on
compressive strength has been investigated. Neemoil (25%)
integrated with copper naphthenate (0.3%) on dilution with kerosene
oil impregnated into bamboo culm at 2 bar pressure, has shown
weight loss of only 3.15% in soil block analysis method. The results
from compressive strength analysis using HEICO Automatic
Compression Testing Machine reveal that preservative treatment has
not altered the structural properties of bamboo culms. Compressive
strength of control (11.72 N/mm2) and above treated samples (11.71
N/mm2) was found to be comparable.
Abstract: The study is devoted to define the optimal conditions
for the nitriding of pure iron at atmospheric pressure by using NH3-
Ar-C3H8 gas mixtures. After studying the mechanisms of phase
formation and mass transfer at the gas-solid interface, a mathematical
model is developed in order to predict the nitrogen transfer rate in the
solid, the ε-carbonitride layer growth rate and the nitrogen and
carbon concentration profiles. In order to validate the model and to
show its possibilities, it is compared with thermogravimetric
experiments, analyses and metallurgical observations (X-ray
diffraction, optical microscopy and electron microprobe analysis).
Results obtained allow us to demonstrate the sound correlation
between the experimental results and the theoretical predictions.