Abstract: Analytical investigation of the free vibration behavior
of circular functionally graded (FG) plates integrated with two
uniformly distributed actuator layers made of piezoelectric (PZT4)
material on the top and bottom surfaces of the circular FG plate
based on the classical plate theory (CPT) is presented in this paper.
The material properties of the functionally graded substrate plate are
assumed to be graded in the thickness direction according to the
power-law distribution in terms of the volume fractions of the
constituents and the distribution of electric potential field along the
thickness direction of piezoelectric layers is simulated by a quadratic
function. The differential equations of motion are solved analytically
for clamped edge boundary condition of the plate. The detailed
mathematical derivations are presented and Numerical investigations
are performed for FG plates with two surface-bonded piezoelectric
layers. Emphasis is placed on investigating the effect of varying the
gradient index of FG plate on the free vibration characteristics of the
structure. The results are verified by those obtained from threedimensional
finite element analyses.
Abstract: The pressure drag from a cam shaped tube in cross flows have been investigated experimentally using pressure distribution measurement. The range of angle of attack and Reynolds number based on an equivalent circular tube are within 0≤α≤360° and 2×104< Reeq < 3.4 ×104, respectively. It is found that the pressure drag coefficient is at its highest at α=90° and 270° over the whole range of Reynolds number. Results show that the pressure drag coefficient of the cam shaped tube is lower than that of circular tube with the same surface area for more of the angles of attack. Furthermore, effects of the diameter ratio and finite length of the cam shaped tube upon the pressure drag coefficient are discussed.
Abstract: This paper describes an effective solution to the task
of a remote monitoring of super-extended objects (oil and gas
pipeline, railways, national frontier). The suggested solution is based
on the principle of simultaneously monitoring of seismoacoustic and
optical/infrared physical fields. The principle of simultaneous
monitoring of those fields is not new but in contrast to the known
solutions the suggested approach allows to control super-extended
objects with very limited operational costs. So-called C-OTDR
(Coherent Optical Time Domain Reflectometer) systems are used to
monitor the seismoacoustic field. Far-CCTV systems are used to
monitor the optical/infrared field. A simultaneous data processing
provided by both systems allows effectively detecting and classifying
target activities, which appear in the monitored objects vicinity. The
results of practical usage had shown high effectiveness of the
suggested approach.
Abstract: In the present study, the lattice Boltzmann Method (LBM) is applied for simulating of Natural Convection in an inclined open ended cavity. The cavity horizontal walls are insulated while the west wall is maintained at a uniform temperature higher than the ambient. Prandtl number is fixed to 0.71 (air) while Rayligh numbers, aspect ratio of the cavity are changed in the range of 103 to 104 and of 1-4, respectively. The numerical code is validated for the previously results for open ended cavities, and then the results of an inclined open ended cavity for various angles of rotating open ended cavity are presented. Result shows by increasing of aspect ratio, the average Nusselt number on hot wall decreases for all rotation angles. When gravity acceleration direction is opposite of standard gravity direction the convection heat transfer has a manner same as conduction.
Abstract: The purpose of this study is to investigate the
efficiency of a double-layer roof in collecting solar energy as an
application to the areas such as raising high-end temperature of
organic Rankine cycle (ORC). The by-product of the solar roof is to
reduce building air-conditioning loads. The experimental apparatus
are arranged to evaluate the effects of the solar roof in absorbing solar
energy. The flow channel is basically formed by an aluminum plate on
top of a plywood plate. The geometric configurations in which the
effects of absorbing energy is analyzed include: a bare uncovered
aluminum plate, a glass-covered aluminum plate, a
glass-covered/black-painted aluminum plate, a plate with variable
lengths, a flow channel with stuffed material (in an attempt on
enhancement of heat conduction), and a flow channel with variable
slanted angles. The experimental results show that the efficiency of
energy collection varies from 0.6 % to 11 % for the geometric
configurations mentioned above. An additional study is carried out
using CFD simulation to investigate the effects of fins on the
aluminum plate. It shows that due to vastly enhanced heat conduction,
the efficiency can reach ~23 % if 50 fins are installed on the aluminum
plate. The study shows that a double-layer roof can efficiently absorb
solar energy and substantially reduce building air-conditioning
loads. On the high end of an organic Rankine cycle, a solar pond is
used to replace the warm surface water of the sea as OTEC (ocean
thermal energy conversion) is the driving energy for the ORC. The
energy collected from the double-layered solar roof can be pumped
into the pond and raise the pond temperature as the pond surface area is
equivalently increased by nearly one-fourth of the total area of the
double-layer solar roof. The effect of raising solar pond temperature is
especially prominent if the double-layer solar roofs are installed in a
community area.
Abstract: The present study investigates numerically the
phenomenon of vortex-shedding and its suppression in twodimensional
mixed convective flow past a square cylinder under the
joint influence of buoyancy and free-stream orientation with respect
to gravity. The numerical experiments have been conducted at a
fixed Reynolds number (Re) of 100 and Prandtl number (Pr) of 0.71,
while Richardson number (Ri) is varied from 0 to 1.6 and freestream
orientation, α, is kept in the range 0o≤ α ≤ 90o, with 0o
corresponding to an upward flow and 90o representing a cross-flow
scenario, respectively. The continuity, momentum and energy
equations, subject to Boussinesq approximation, are discretized using
a finite difference method and are solved by a semi-explicit pressure
correction scheme. The critical Richardson number, leading to the
suppression of the vortex-shedding (Ric), is estimated by using
Stuart-Landau theory at various free-stream orientations and the
neutral curve is obtained in the Ri-α plane. The neutral curve
exhibits an interesting non-monotonic behavior with Ric first
increasing with increasing values of α upto 45o and then decreasing
till 70o. Beyond 70o, the neutral curve again exhibits a sharp
increasing asymptotic trend with Ric approaching very large values
as α approaches 90o. The suppression of vortex shedding is not
observed at α = 90o (cross-flow). In the unsteady flow regime, the
Strouhal number (St) increases with the increase in Richardson
number.
Abstract: This research was to study effect of rotational speed
and eccentric factors, which were affected on looseness of bearing.
The experiment was conducted on three rotational speeds and five
eccentric distances with 5 replications. The results showed that
influenced factor affected to looseness of bearing was rotational
speed and eccentric distance which showed statistical significant.
Higher rotational speed would cause on high looseness. Moreover,
more eccentric distance, more looseness of bearing. Using bearing at
high rotational with high eccentric of shaft would be affected
bearing fault more than lower rotational speed. The prediction
equation of looseness was generated by regression analysis. The
prediction has an effected to the looseness of bearing at 91.5%.
Abstract: One of the main concerns about parallel mechanisms
is the presence of singular points within their workspaces. In singular
positions the mechanism gains or loses one or several degrees of
freedom. It is impossible to control the mechanism in singular
positions. Therefore, these positions have to be avoided. This is a
vital need especially in computer controlled machine tools designed
and manufactured on the basis of parallel mechanisms. This need has
to be taken into consideration when selecting design parameters. A
prerequisite to this is a thorough knowledge about the effect of
design parameters and constraints on singularity. In this paper,
quality condition index was introduced as a criterion for evaluating
singularities of different configurations of a hexapod mechanism
obtainable by different design parameters. It was illustrated that this
method can effectively be employed to obtain the optimum
configuration of hexapod mechanism with the aim of avoiding
singularity within the workspace. This method was then employed to
design the hexapod table of a CNC milling machine.
Abstract: A novel method using bearing-only SLAM to estimate node positions of a localization network is proposed. A group of simple robots are used to estimate the position of each node. Each node has a unique ID, which it can communicate to a robot close by. Initially the node IDs and positions are unknown. A case example using RFID technology in the localization network is introduced.
Abstract: In hydrocyclones, the particle separation efficiency is
limited by the suspended fine particles, which are discharged with the
coarse product in the underflow. It is well known that injecting water
in the conical part of the cyclone reduces the fine particle fraction in
the underflow. This paper presents a mathematical model that
simulates the water injection in the conical component. The model
accounts for the fluid flow and the particle motion. Particle
interaction, due to hindered settling caused by increased density and
viscosity of the suspension, and fine particle entrainment by settling
coarse particles are included in the model. Water injection in the
conical part of the hydrocyclone is performed to reduce fine particle
discharge in the underflow. The model demonstrates the impact of
the injection rate, injection velocity, and injection location on the
shape of the partition curve. The simulations are compared with
experimental data of a 50-mm cyclone.
Abstract: Three dimensional analysis of thermal model in laser
full penetration welding, Nd:YAG, by transparent mode DP600 alloy
steel 1.25mm of thickness and gap of 0.1mm. Three models studied
the influence of thermal dependent temperature properties, thermal
independent temperature and the effect of peak value of specific heat
at phase transformation temperature, AC1, on the transient
temperature. Another seven models studied the influence of
discretization, meshes on the temperature distribution in weld plate.
It is shown that for the effects of thermal properties, the errors less
4% of maximum temperature in FZ and HAZ have identified. The
minimum value of discretization are at least one third increment per
radius for temporal discretization and the spatial discretization
requires two elements per radius and four elements through thickness
of the assembled plate, which therefore represent the minimum
requirements of modeling for the laser welding in order to get
minimum errors less than 5% compared to the fine mesh.
Abstract: Resource-constrained project scheduling is an NPhard
optimisation problem. There are many different heuristic
strategies how to shift activities in time when resource requirements
exceed their available amounts. These strategies are frequently based
on priorities of activities. In this paper, we assume that a suitable
heuristic has been chosen to decide which activities should be
performed immediately and which should be postponed and
investigate the resource-constrained project scheduling problem
(RCPSP) from the implementation point of view. We propose an
efficient routine that, instead of shifting the activities, extends their
duration. It makes it possible to break down their duration into active
and sleeping subintervals. Then we can apply the classical Critical
Path Method that needs only polynomial running time. This
algorithm can simply be adapted for multiproject scheduling with
limited resources.
Abstract: The techniques for estimating the adhesive and cohesive strength in high velocity oxy fuel (HVOF) thermal spray coatings have been discussed and compared. The development trend and the last investigation have been studied. We will focus on benefits and limitations of these methods in different process and materials.
Abstract: This study has investigated a vehicle Lumped
Parameter Model (LPM) in frontal crash. There are several ways for
determining spring and damper characteristics and type of problem
shall be considered as system identification. This study use Genetic
Algorithm (GA) procedure, being an effective procedure in case of
optimization issues, for optimizing errors, between target data
(experimental data) and calculated results (being obtained by
analytical solving). In this study analyzed model in 5-DOF then
compared our results with 5-DOF serial model. Finally, the response
of model due to external excitement is investigated.
Abstract: Induction machine models used for steady-state and
transient analysis require machine parameters that are usually
considered design parameters or data. The knowledge of induction
machine parameters is very important for Indirect Field Oriented
Control (IFOC). A mismatched set of parameters will degrade the
response of speed and torque control. This paper presents an
improvement approach on rotor time constant adaptation in IFOC for
Induction Machines (IM). Our approach tends to improve the
estimation accuracy of the fundamental model for flux estimation.
Based on the reduced order of the IM model, the rotor fluxes and
rotor time constant are estimated using only the stator currents and
voltages. This reduced order model offers many advantages for real
time identification parameters of the IM.
Abstract: In this research a comparison between k-epsilon and
LES model for a deoiling hydrocyclone is conducted. Flow field of
hydrocyclone is obtained by three-dimensional simulations with
OpenFOAM code. Potential of prediction for both methods of this
complex swirl flow is discussed. Large eddy simulation method
results have more similarity to experiment and its results are
presented in figures from different hydrocyclone cross sections.
Abstract: In this paper multi-objective genetic algorithms are
employed for Pareto approach optimization of ideal Turboshaft
engines. In the multi-objective optimization a number of conflicting
objective functions are to be optimized simultaneously. The
important objective functions that have been considered for
optimization are specific thrust (F/m& 0), specific fuel consumption
( P S ), output shaft power 0 (& /&) shaft W m and overall efficiency( ) O
η .
These objectives are usually conflicting with each other. The design
variables consist of thermodynamic parameters (compressor pressure
ratio, turbine temperature ratio and Mach number).
At the first stage single objective optimization has been
investigated and the method of NSGA-II has been used for multiobjective
optimization. Optimization procedures are performed for
two and four objective functions and the results are compared for
ideal Turboshaft engine. In order to investigate the optimal
thermodynamic behavior of two objectives, different set, each
including two objectives of output parameters, are considered
individually. For each set Pareto front are depicted. The sets of
selected decision variables based on this Pareto front, will cause the
best possible combination of corresponding objective functions.
There is no superiority for the points on the Pareto front figure,
but they are superior to any other point. In the case of four objective
optimization the results are given in tables.
Abstract: This paper focuses on the probabilistic numerical
solution of the problems in biomechanics and mining. Applications of
Simulation-Based Reliability Assessment (SBRA) Method are
presented in the solution of designing of the external fixators applied
in traumatology and orthopaedics (these fixators can be applied for
the treatment of open and unstable fractures etc.) and in the solution
of a hard rock (ore) disintegration process (i.e. the bit moves into the
ore and subsequently disintegrates it, the results are compared with
experiments, new design of excavation tool is proposed.
Abstract: In this paper, Neuro-Fuzzy based Fuzzy Subtractive
Clustering Method (FSCM) and Self Tuning Fuzzy PD-like
Controller (STFPDC) were used to solve non-linearity and trajectory
problems of pitch AND yaw angles of Twin Rotor MIMO system
(TRMS). The control objective is to make the beams of TRMS reach
a desired position quickly and accurately. The proposed method
could achieve control objectives with simpler controller. To simplify
the complexity of STFPDC, ANFIS based FSCM was used to
simplify the controller and improve the response. The proposed
controllers could achieve satisfactory objectives under different input
signals. Simulation results under MATLAB/Simulink® proved the
improvement of response and superiority of simplified STFPDC on
Fuzzy Logic Controller (FLC).
Abstract: This paper presents a numerical study on surface heat
transfer characteristics of laminar air flows in parallel-plate dimpled
channels. The two-dimensional numerical model is provided by
commercial code FLUENT and the results are obtained for channels
with symmetrically opposing hemi-cylindrical cavities onto both
walls for Reynolds number ranging from 1000 to 2500. The influence
of variations in relative depth of dimples (the ratio of cavity depth to
the cavity curvature diameter), the number of them and the thermophysical
properties of channel walls on heat transfer enhancement is
studied. The results are evident for existence of an optimum value for
the relative depth of dimples in which the largest wall heat flux and
average Nusselt number can be achieved. In addition, the results of
conjugation simulation indicate that the overall influence of the ratio
of wall thermal conductivity to the one of the fluid on heat transfer
rate is not much significant and can be ignored.