Abstract: The issue of turbulence base streams and the drag related to it have been of important attention for rockets, missiles, and aircraft. Different techniques are used for base drag reduction. This paper presents the numerical study of numerous drag reduction technique. The base drag or afterbody drag of bluff bodies can be reduced easily using locked vortex drag reduction technique. For bluff bodies having a cylindrical shape, the base drag is much larger compared to streamlined bodies. For such bodies using splitter plates, the vortex can be trapped between the base and the plate, which results in smooth flow. Splitter plate with round and curved corner shapes has influence in drag reduction. In this paper, the comparison is done between single splitter plate as different positions and with the bluff body. Base drag for the speed of 30m/s can be reduced about 20% to 30% by using single splitter plate as compared to the bluff body.
Abstract: This paper presents an experimental investigation for the characteristics of an energy harvesting device exploiting flow-induced vibration in a wind tunnel. A stationary bluff body is connected with a downstream tip body via an aluminium cantilever beam. Various lengths of aluminium cantilever beam and different shapes of downstream tip body are considered. The results show that the characteristics of the energy harvester’s vibration depend on both the length of the aluminium cantilever beam and the shape of the downstream tip body. The highest ratio between vibration amplitude and bluff body diameter was found to be 1.39 for an energy harvester with a symmetrical triangular tip body and L/D1 = 5 at 9.8 m/s of flow speed (Re = 20077). Using this configuration, the electrical energy was extracted with a polyvinylidene fluoride (PVDF) piezoelectric beam with different load resistances, of which the optimal value could be found on each Reynolds number. The highest power output was found to be 3.19 µW, at 9.8 m/s of flow speed (Re = 20077) and 27 MΩ of load resistance.
Abstract: The study aims to understand the surface pressure distribution around the bodies such as the suction pressure in the leading edge on the top and side-face when the aspect ratio of bodies and the wind direction are changed, respectively. We carried out the wind tunnel measurement and numerical simulation around a series of rectangular bodies (40d×80w×80h, 80d×80w×80h, 160d×80w×80h, 80d×40w×80h and 80d×160w×80h in mm3) placed in a deep turbulent boundary layer. Based on a modern numerical platform, the Navier-Stokes equation with the typical 2-equation (k-ε model) and the DES (Detached Eddy Simulation) turbulence model has been calculated, and they are both compared with the measurement data. Regarding the turbulence model, the DES model makes a better prediction comparing with the k-ε model, especially when calculating the separated turbulent flow around a bluff body with sharp edged corner. In order to observe the effect of wind direction on the pressure variation around the cube (e.g., 80d×80w×80h in mm), it rotates at 0º, 10º, 20º, 30º, and 45º, which stands for the salient wind directions in the tunnel. The result shows that the surface pressure variation is highly dependent upon the approaching wind direction, especially on the top and the side-face of the cube. In addition, the transverse width has a substantial effect on the variation of surface pressure around the bodies, while the longitudinal length has little or no influence.
Abstract: For a bluff body, roughness elements in simulating a turbulent boundary layer, leading to delayed flow separation, a smaller wake, and lower form drag. In the present work, flow past a circular cylinder with using tripping wires is studied experimentally. The wind tunnel used for modeling free stream is open blow circuit (maximum speed = 30m/s and maximum turbulence of free stream = 0.1%). The selected Reynolds number for all tests was constant (Re = 25000). The circular cylinder selected for this experiment is 20 and 400mm in diameter and length, respectively. The aim of this research is to find the optimal operation mode. In this study installed some tripping wires 1mm in diameter, with a different number of wires on the circular cylinder and the wake characteristics of the circular cylinder is studied. Results showed that by increasing number of tripping wires attached to the circular cylinder (6, 8, and 10, respectively), The optimal angle for the tripping wires with 1mm in diameter to be installed on the cylinder is 60̊ (or 6 wires required at angle difference of 60̊). Strouhal number for the cylinder with tripping wires 1mm in diameter at angular position 60̊ showed the maximum value.
Abstract: A two-dimensional numerical study for flow past a square cylinder in presence of flat plate both at upstream and downstream position is carried out using the single-relaxation-time lattice Boltzmann method for gap spacing 0.5 and 1. We select Reynolds numbers from 80 to 200. The wake structure mechanism within gap spacing and near wake region, vortex structures around and behind the main square cylinder in presence of flat plate are studied and compared with flow pattern around a single square cylinder. The results are obtained in form of vorticity contour, streamlines, power spectra analysis, time trace analysis of drag and lift coefficients. Four different types of flow patterns were observed in both configurations, named as (i) Quasi steady flow (QSF), (ii) steady flow (SF), (iii) shear layer reattachment (SLR), (iv) single bluff body (SBB). It is observed that upstream flat plate plays a vital role in significant drag reduction. On the other hand, rate of suppression of vortex shedding is high for downstream flat plate case at low Reynolds numbers. The reduction in mean drag force and root mean square value of drag force for upstream flat plate case are89.1% and 86.3% at (Re, g) = (80, 0.5d) and (120, 1d) and reduction for downstream flat plate case for mean drag force and root mean square value of drag force are 11.10% and 97.6% obtained at (180, 1d) and (180, 0.5d).
Abstract: For a bluff body, dimples behave like roughness
elements in stimulating a turbulent boundary layer, leading to delayed
flow separation, a smaller wake and lower form drag. This is very
different in principle from the application of dimples to streamlined
body, where any reduction in drag would be predominantly due to a
reduction in skin friction. In the present work, a car model with
different dimple geometry is simulated using k-ε turbulence modeling
to determine its effect to the aerodynamics performance. Overall, the
results show that the application of dimples manages to reduce the
drag coefficient of the car model.
Abstract: The global demand for continuous and eco-friendly
renewable energy as alternative to fossils fuels is large and ever
growing in nowadays. This paper will focus on capability of Vortex
Induced Vibration (VIV) phenomenon in generating alternative
energy for offshore platform application. In order to maximize the
potential of energy generation, the effects of lock in phenomenon and
different geometries of cylinder were studied in this project. VIV is
the motion induced on bluff body which creates alternating lift forces
perpendicular to fluid flow. Normally, VIV is unwanted in order to
prevent mechanical failure of the vibrating structures. But in this
project, instead of eliminating these vibrations, VIV will be exploited
to transform these vibrations into a valuable resource of energy.
Abstract: The aim of present study is to control the unsteady flow structure downstream of a circular cylinder by use of attached permeable plates. Particle image velocimetry (PIV) technique and dye visualization experiments were performed in deep water and the flow characteristics were evaluated by means of time-averaged streamlines, Reynolds Shear Stress and Turbulent Kinetic Energy concentrations. The permeable plate was made of a chrome-nickel screen having a porosity value of β=0.6 and it was attached on the cylinder surface along its midspan. Five different angles were given to the plate (θ=0o, 15o, 30o, 45o, 60o) with respect to the centerline of the cylinder in order to examine its effect on the flow control. It was shown that the permeable plate is effective on elongating the vortex formation length and reducing the fluctuations in the wake region. Compared to the plain cylinder, the reductions in the values of maximum Reynolds shear stress and Turbulent Kinetic Energy were evaluated as 72.5% and 66%, respectively for the plate angles of θ=45oand 60o which were also found to be suggested for applications concerning the vortex shedding and consequent Vortex-Induced Vibrations.
Abstract: A two-dimensional numerical simulation of crossflow
around four cylinders in an in-line rectangular configuration is
studied by using the lattice Boltzmann method (LBM). Special
attention is paid to the effect of the spacing between the cylinders.
The Reynolds number ( Re ) is chosen to be e 100 R = and the
spacing ratio L / D is set at 0.5, 1.5, 2.5, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0
and 10.0. Results show that, as in the case of four cylinders in an inline
rectangular configuration , flow fields show four different
features depending on the spacing (single square cylinder, stable
shielding flow, wiggling shielding flow and a vortex shedding flow)
are observed in this study. The effects of spacing ratio on physical
quantities such as mean drag coefficient, Strouhal number and rootmean-
square value of the drag and lift coefficients are also presented.
There is more than one shedding frequency at small spacing ratios.
The mean drag coefficients for downstream cylinders are less than
that of the single cylinder for all spacing ratios. The present results
using the LBM are compared with some existing experimental data
and numerical studies. The comparison shows that the LBM can
capture the characteristics of the bluff body flow reasonably well and
is a good tool for bluff body flow studies.
Abstract: The interaction between wakes of bluff body and
airfoil have profound influences on system performance in many
industrial applications, e.g., turbo-machinery and cooling fan. The
present work investigates the effect of configuration include; airfoil-s
angle of attack, transverse and inline spacing of the models, on
frequency behavior of the cylinder-s near-wake. The experiments
carried on under subcritical flow regime, using the hot-wire
anemometry (HWA). The relationship between the Strouhal numbers
and arrangements provide an insight into the global physical
processes of wake interaction and vortex shedding.
Abstract: Vortex-shedding phenomenon of the flow
around combined two bodies having various geometries and sizes has been investigated experimentally in the Reynolds
number range between 4.1x103 and 1.75x104. To see the effect
of the rotation of the bodies on the vortex shedding, the
combined bodies were rotated from 0° to 180°. The combined models have a cross section composing of a main circular cylinder and an attached circular or square cylinder. Results
have shown that Strouhal numbers for two cases were
changed considerably with the angle of incidence, while it was found to be largely independent of Reynolds number at 150. Characteristics of the vortex formation region and
location of flow attachments, reattachments, and separations
were observed by means of the flow visualizations.
Depending on the inclination angle the effects of flow
attachment, separation and reattachment on vortex-shedding phenomenon have been discussed.
Abstract: The objective of this research was to find the diffusion properties of vehicles on the road by using the V-Sphere Code. The diffusion coefficient and the size of the height of the wake were estimated with the LES option and the third order MUSCL scheme. We evaluated the code with the changes in the moments of Reynolds Stress along the mean streamline. The results show that at the leading part of a bluff body the LES has some advantages over the RNS since the changes in the strain rates are larger for the leading part. We estimated that the diffusion coefficient with the computed Reynolds stress (non-dimensional) was about 0.96 times the mean velocity.
Abstract: The present study investigates numerically the
phenomenon of vortex-shedding and its suppression in twodimensional
mixed convective flow past a square cylinder under the
joint influence of buoyancy and free-stream orientation with respect
to gravity. The numerical experiments have been conducted at a
fixed Reynolds number (Re) of 100 and Prandtl number (Pr) of 0.71,
while Richardson number (Ri) is varied from 0 to 1.6 and freestream
orientation, α, is kept in the range 0o≤ α ≤ 90o, with 0o
corresponding to an upward flow and 90o representing a cross-flow
scenario, respectively. The continuity, momentum and energy
equations, subject to Boussinesq approximation, are discretized using
a finite difference method and are solved by a semi-explicit pressure
correction scheme. The critical Richardson number, leading to the
suppression of the vortex-shedding (Ric), is estimated by using
Stuart-Landau theory at various free-stream orientations and the
neutral curve is obtained in the Ri-α plane. The neutral curve
exhibits an interesting non-monotonic behavior with Ric first
increasing with increasing values of α upto 45o and then decreasing
till 70o. Beyond 70o, the neutral curve again exhibits a sharp
increasing asymptotic trend with Ric approaching very large values
as α approaches 90o. The suppression of vortex shedding is not
observed at α = 90o (cross-flow). In the unsteady flow regime, the
Strouhal number (St) increases with the increase in Richardson
number.
Abstract: The effects of dynamic subgrid scale (SGS) models are
investigated in variational multiscale (VMS) LES simulations of bluff
body flows. The spatial discretization is based on a mixed finite
element/finite volume formulation on unstructured grids. In the VMS
approach used in this work, the separation between the largest and the
smallest resolved scales is obtained through a variational projection
operator and a finite volume cell agglomeration. The dynamic version
of Smagorinsky and WALE SGS models are used to account for
the effects of the unresolved scales. In the VMS approach, these
effects are only modeled in the smallest resolved scales. The dynamic
VMS-LES approach is applied to the simulation of the flow around a
circular cylinder at Reynolds numbers 3900 and 20000 and to the flow
around a square cylinder at Reynolds numbers 22000 and 175000. It
is observed as in previous studies that the dynamic SGS procedure
has a smaller impact on the results within the VMS approach than in
LES. But improvements are demonstrated for important feature like
recirculating part of the flow. The global prediction is improved for
a small computational extra cost.
Abstract: This paper presents a CFD analysis of the flow field
around a thin flat plate of infinite span inclined at 90° to a fluid
stream of infinite extent. Numerical predictions have been compared
to experimental measurements, in order to assess the potential of the
finite volume code of determining the aerodynamic forces acting on a
bluff body invested by a fluid stream of infinite extent.
Several turbulence models and spatial node distributions have
been tested. Flow field characteristics in the neighborhood of the flat
plate have been investigated, allowing the development of a
preliminary procedure to be used as guidance in selecting the
appropriate grid configuration and the corresponding turbulence
model for the prediction of the flow field over a two-dimensional
vertical flat plate.