Abstract: This paper presents a simple three phase power flow
method for solution of three-phase unbalanced radial distribution
system (RDN) with voltage dependent loads. It solves a simple
algebraic recursive expression of voltage magnitude, and all the data
are stored in vector form. The algorithm uses basic principles of
circuit theory and can be easily understood. Mutual coupling between
the phases has been included in the mathematical model. The
proposed algorithm has been tested with several unbalanced radial
distribution networks and the results are presented in the article. 8-
bus and IEEE 13 bus unbalanced radial distribution system results
are in agreements with the literature and show that the proposed
model is valid and reliable.
Abstract: Robust stability and performance are the two most
basic features of feedback control systems. The harmonic balance
analysis technique enables to analyze the stability of limit cycles
arising from a neural network control based system operating over
nonlinear plants. In this work a robust stability analysis based on the
harmonic balance is presented and applied to a neural based control
of a non-linear binary distillation column with unstructured
uncertainty. We develop ways to describe uncertainty in the form of
neglected nonlinear dynamics and high harmonics for the plant and
controller respectively. Finally, conclusions about the performance of
the neural control system are discussed using the Nyquist stability
margin together with the structured singular values of the uncertainty
as a robustness measure.
Abstract: The residue number system (RNS) is popular in high performance computation applications because of its carry-free nature. The challenges of RNS systems design lie in the moduli set selection and in the reverse conversion from residue representation to weighted representation. In this paper, we proposed a fully parallel reverse conversion algorithm for the moduli set {rn - 2, rn - 1, rn}, based on simple mathematical relationships. Also an efficient hardware realization of this algorithm is presented. Our proposed converter is very faster and results to hardware savings, compared to the other reverse converters.
Abstract: According to the increasing utilization in power system, the transmission lines and power plants often operate in stability boundary and system probably lose its stable condition by over loading or occurring disturbance. According to the reasons that are mentioned, the prediction and recognition of voltage instability in power system has particular importance and it makes the network security stronger.This paper, by considering of power system contingencies based on the effects of them on Mega Watt Margin (MWM) and maximum loading point is focused in order to analyse the static voltage stability using continuation power flow method. The study has been carried out on IEEE 14-Bus Test System using Matlab and Psat softwares and results are presented.
Abstract: This paper presents a predictive model of sensor readings for mobile robot. The model predicts sensor readings for given time horizon based on current sensor readings and velocities of wheels assumed for this horizon. Similar models for such anticipation have been proposed in the literature. The novelty of the model presented in the paper comes from the fact that its structure takes into account physical phenomena and is not just a black box, for example a neural network. From this point of view it may be regarded as a semi-phenomenological model. The model is developed for the Khepera robot, but after certain modifications, it may be applied for any robot with distance sensors such as infrared or ultrasonic sensors.
Abstract: An efficient reintegration of the disabled people in the
family and society should be fulfilled; hence it is strongly needful to assist their diminished functions or to replace the totally lost
functions. Assistive technology helps in neutralizing the impairment.
Recent advancements in embedded systems have opened up a vast
area of research and development for affordable and portable assistive devices for the visually impaired. Granted there are many assistive devices on the market that are able to detect obstacles, and numerous research and development currently in process to
alleviate the cause, unfortunately the cost of devices, size of
devices, intrusiveness and higher learning curve prevents the visually impaired from taking advantage of available devices. This
project aims at the design and implementation of a detachable unit
which is robust, low cost and user friendly, thus, trying to
aggrandize the functionality of the existing white cane, to concede above-knee obstacle detection. The designed obstruction detector
uses ultrasound sensors for detecting the obstructions before direct contact. It bestows haptic feedback to the user in accordance with the position of the obstacle.
Abstract: In this paper, backstepping method (BM) is proposed for a single-link flexible mechanical manipulator. In each step of this method a positive value is obtained. Selections of the gain factor values are very important because controller will have different behavior for each different set of values. Improper selection of these gains can lead to instability of the system. In order to choose proper values for gains BELBIC method has been used in this work. Finally, to prove the efficiency of this method, the obtained results of proposed model are compared with robust controller one. Results show that the combination of backstepping and BELBIC that is presented here, can stabilized the system with higher speed, shorter settling time and lower overshoot in than robust controller.
Abstract: The electrical power systems of aircrafts have made
serious progress in recent years because the aircrafts depend more
and more on the electricity. There is a trend in the aircraft industry to
replace hydraulic and pneumatic systems with electrical systems,
achieving more comfort and monitoring features and enlarging the
energetic efficiency. Thus, was born the concept More Electric
Aircraft. In this paper is analyzed the integration of a fuel cell into
the existing electrical generation and distribution systems of an
aircraft. The dynamic characteristics of fuel cell systems necessitate
an adaptation of the electrical power system. The architecture studied
in this paper consists of a 50kW fuel cell, a dc to dc converter and
several loads. The dc to dc converter is used to step down the fuel
cell voltage from about 625Vdc to 28Vdc.
Abstract: Image registration is the process of establishing point
by point correspondence between images obtained from a same
scene. This process is very useful in remote sensing, medicine,
cartography, computer vision, etc. Then, the task of registration is to
place the data into a common reference frame by estimating the
transformations between the data sets. In this work, we develop a
rigid point registration method based on the application of genetic
algorithms and Hausdorff distance. First, we extract the feature points
from both images based on the algorithm of global and local
curvature corner. After refining the feature points, we use Hausdorff
distance as similarity measure between the two data sets and for
optimizing the search space we use genetic algorithms to achieve
high computation speed for its inertial parallel. The results show the
efficiency of this method for registration of satellite images.
Abstract: In power system protection, the need to know the load
current together with the fault level detected by a relay is important.
This is due to the fact that the relay is required to isolate the
equipment being protected if a fault is present and keep the breaker
associated with it closed if the current level is lower than the
maximum load level. This is not an issue for a radial system. This is
not the same however in a looped power system. In a looped power
system, the isolation of an equipment system will contribute to a
topology change. The change in the power system topology will then
influence or change the maximum load current and the fault level
detected by each relay. In this paper, a method of data collection for
changing topology using matlab and sim-power will be presented.
The method will take into consideration the change in topology and
collect data for each possible topology.
Abstract: Force sensor has been used as requisite for knowing information on the amount and the directions of forces on the skin surface. We have developed a four-degrees-of-freedom capacitive force sensor (approximately 20×20×5 mm3) that has a flexible structure and sixteen parallel plate capacitors. An iterative algorithm was developed for estimating four displacements from the sixteen capacitances using fourth-order polynomial approximation of characteristics between capacitance and displacement. The estimation results from measured capacitances had large error caused by deterioration of the characteristics. In this study, effective capacitors had major information were selected on the basis of the capacitance change range and the characteristic shape. Maximum errors in calibration and non-calibration points were 25%and 6.8%.However the maximum error was larger than desired value, the smallness of averaged value indicated the occurrence of a few large error points. On the other hand, error in non-calibration point was within desired value.
Abstract: The performance of state of the art worldwide telecommunication networks strongly depends on the efficiency of the applied routing mechanism. Game theoretical approaches to this problem offer new solutions. In this paper a new continuous network routing model is defined to describe data transfer in fixed telecommunication networks of multiple hosts. The nodes of the network correspond to routers whose latency is assumed to be traffic dependent. We propose that the whole traffic of the network can be decomposed to a finite number of tasks, which belong to various hosts. To describe the different latency-sensitivity, utility functions are defined for each task. The model is used to compare router and host intelligent types of routing methods, corresponding to various data transfer protocols. We analyze host intelligent routing as a transferable utility cooperative game with externalities. The main aim of the paper is to provide a framework in which the efficiency of various routing algorithms can be compared and the transferable utility game arising in the cooperative case can be analyzed.
Abstract: In this paper, a low-power digital controller for DC-DC power conversion was presented. The controller generates the pulse-width modulated (PWM) signal from digital inputs provided by analog-to-digital converter (ADC). An efficient and simple design scheme to develop the control unit was discussed. This method allows minimization of the consumed resources of the chip and it is based on direct digital design approach. In this application, with the proposed scheme, nearly half area and two-third of the power consumption was saved compared to the conventional schemes. This work illustrates the possibility of implementing low-power and area-efficient power management circuit using direct digital design based approach.
Abstract: Discrete wavelet transform (DWT) has been widely adopted in biomedical signal processing for denoising, compression
and so on. Choosing a suitable decomposition level (DL) in DWT is of paramount importance to its performance. In this paper, we propose to exploit sparseness of the transformed signals to determine the appropriate DL. Simulation results have shown that the sparseness of transformed signals after DWT increases with the increasing DLs. Additional Monte-Carlo simulation results have verified the effectiveness of sparseness measure in determining the DL.
Abstract: Due to side-peaks of autocorrelation function, the binary offset carrier (BOC) signal acquisition suffers from an ambiguity when one of the side-peaks is acquired. In this paper, we first analyze that the BOC autocorrelation is made up of the sum of subcorrelations, and then, remove the side-peaks causing the ambiguity by recombining the sub-correlations. The proposed scheme is shown to remove the side-peaks completely. From numerical results, it is confirmed that the proposed scheme outperforms the conventional schemes in terms of the receiver operating characteristic and mean acquisition time.
Abstract: The success of renewable powered electric vehicle
charging station in isolated areas depends highly on the availability
and sustainability of renewable resources all year round at a selected
location. The main focus of this paper is to discuss the possible
charging strategies that could be implemented to find the best
possible configuration of an electric Tuk-Tuk charging station at a
given location within South Africa. The charging station is designed,
modeled and simulated to evaluate its performances. The technoeconomic
analysis of different feasible supply configurations of the
charging station using renewable energies is simulated using
HOMER software and the results compared in order to select the best
possible charging strategies in terms of cost of energy consumed.
Abstract: This paper, proposes a control system for use with microgrid consiste of multiple small scale embedded generation networks (SSEG networks) connected to the 33kV distribution network. The proposed controller controls power flow in the grid-connected mode of operation, enables voltage and frequency control when the SSEG networks are islanded, and resynchronises the SSEG networks with the utility before reconnecting them. The performance of the proposed controller has been tested in simulations using PSCAD.
Abstract: This paper investigates the suitability of Latin Hypercube sampling (LHS) for composite electric power system reliability analysis. Each sample generated in LHS is mapped into an equivalent system state and used for evaluating the annualized system and load point indices. DC loadflow based state evaluation model is solved for each sampled contingency state. The indices evaluated are loss of load probability, loss of load expectation, expected demand not served and expected energy not supplied. The application of the LHS is illustrated through case studies carried out using RBTS and IEEE-RTS test systems. Results obtained are compared with non-sequential Monte Carlo simulation and state enumeration analytical approaches. An error analysis is also carried out to check the LHS method’s ability to capture the distributions of the reliability indices. It is found that LHS approach estimates indices nearer to actual value and gives tighter bounds of indices than non-sequential Monte Carlo simulation.
Abstract: In this paper, we present a localization of a mobile robot with localization modules which have two ceiling-view cameras in indoor environments. We propose two kinds of localization method. The one is the localization in the local space; we use the line feature and the corner feature between the ceiling and wall. The other is the localization in the large space; we use the natural features such as bulbs, structures on the ceiling. These methods are installed on the embedded module able to mount on the robot. The embedded module has two cameras to be able to localize in both the local space and the large spaces. The experiment is practiced in our indoor test-bed and a government office. The proposed method is proved by the experimental results.
Abstract: This paper presents a methodology to assess the voltage stability status combined with optimal power flow technique using an instantaneous two-bus equivalent model of power system incorporating static var compensator (SVC) and thyristor controlled series compensator (TCSC) controllers. There by, a generalized global voltage stability indicator being developed has been applied to a robust practical Indian Eastern Grid 203-bus system. Simulation results have proved that the proposed methodology is promising to assess voltage stability of any power system at any operating point in global scenario. Voltage stability augmentation with the application of SVC at the weakest bus and TCSC at critical line connected to the weakest bus is compared with the system having no compensation. In the proposed network equivalent model the generators have been modeled more accurately considering economic criteria.