Abstract: This paper presents a multi-objective formulation for
optimal siting and sizing of distributed generation (DG) resources in
distribution systems in order to minimize the cost of power losses
and energy not supplied. The implemented technique is based on
particle swarm optimization (PSO) and weight method that employed
to obtain the best compromise between these costs. Simulation
results on 33-bus distribution test system are presented to
demonstrate the effectiveness of the proposed procedure.
Abstract: In this paper, we study statistical multiplexing of VBR
video in ATM networks. ATM promises to provide high speed realtime
multi-point to central video transmission for telemedicine
applications in rural hospitals and in emergency medical services.
Video coders are known to produce variable bit rate (VBR) signals
and the effects of aggregating these VBR signals need to be
determined in order to design a telemedicine network infrastructure
capable of carrying these signals. We first model the VBR video
signal and simulate it using a generic continuous-data autoregressive
(AR) scheme. We carry out the queueing analysis by the Fluid
Approximation Model (FAM) and the Markov Modulated Poisson
Process (MMPP). The study has shown a trade off: multiplexing
VBR signals reduces burstiness and improves resource utilization,
however, the buffer size needs to be increased with an associated
economic cost. We also show that the MMPP model and the Fluid
Approximation model fit best, respectively, the cell region and the
burst region. Therefore, a hybrid MMPP and FAM completely
characterizes the overall performance of the ATM statistical
multiplexer. The ramifications of this technology are clear: speed,
reliability (lower loss rate and jitter), and increased capacity in video
transmission for telemedicine. With migration to full IP-based
networks still a long way to achieving both high speed and high
quality of service, the proposed ATM architecture will remain of
significant use for telemedicine.
Abstract: A technique proposed for the automatic detection
of spikes in electroencephalograms (EEG). A multi-resolution
approach and a non-linear energy operator are exploited. The
signal on each EEG channel is decomposed into three sub bands
using a non-decimated wavelet transform (WT). The WT is a
powerful tool for multi-resolution analysis of non-stationary signal
as well as for signal compression, recognition and restoration.
Each sub band is analyzed by using a non-linear energy operator,
in order to detect spikes. A decision rule detects the presence of
spikes in the EEG, relying upon the energy of the three sub-bands.
The effectiveness of the proposed technique was confirmed by
analyzing both test signals and EEG layouts.
Abstract: This paper describes identification of the two poles
unstable SOPDT process, especially with large time delay. A new
modified relay feedback identification method for two poles unstable
SOPDT process is proposed. Furthermore, for the two poles unstable
SOPDT process, an additional Derivative controller is incorporated
parallel with relay to relax the constraint on the ratio of delay to the
unstable time constant, so that the exact model parameters of
unstable processes can be identified. To cope with measurement
noise in practice, a low pass filter is suggested to get denoised output
signal toimprove the exactness of model parameter of unstable
process. PID Lead-lag tuning formulas are derived for two poles
unstable (SOPDT) processes based on IMC principle. Simulation
example illustrates the effectiveness and the simplicity of the
proposed identification and control method.
Abstract: This paper presents comparison among methods of
determination of the characteristic polynomial coefficients. First, the
resultant systems from the methods are compared based on frequency
criteria such as the closed loop bandwidth, gain and phase margins.
Then the step responses of the resultant systems are compared on the
basis of the transient behavior criteria including overshoot, rise time,
settling time and error (via IAE, ITAE, ISE and ITSE integral
indices). Also relative stability of the systems is compared together.
Finally the best choices in regards to the above diverse criteria are
presented.
Abstract: Realistic systems generally are systems with various
inputs and outputs also known as Multiple Input Multiple Output
(MIMO). Such systems usually prove to be complex and difficult to
model and control purposes. Therefore, decomposition was used to
separate individual inputs and outputs. A PID is assigned to each
individual pair to regulate desired settling time. Suitable parameters
of PIDs obtained from Genetic Algorithm (GA), using Mean of
Squared Error (MSE) objective function.
Abstract: This paper develops a pedometer with a three-axis acceleration sensor that can be placed with any angle. The proposed pedometer measures the number of steps while users walk, jog or run. It can be worn on users’ waistband or placed within pocket or backpack. The work address to improve on the general pedometers, which can only be used in a single direction or can only count of steps without the continuous exercise judgment mechanism. Finally, experimental results confirm the superior performance of the proposed pedometer.
Abstract: This paper proposes an adaptive sliding mode
controller which combines adaptive control and sliding
mode control to control a nonlinear robotic manipulator
with uncertain parameters. We use an adaptive algorithm
based on the concept of sliding mode control to alleviate the
chattering phenomenon of control input. Adaptive laws are
developed to obtain the gain of switching input and the
boundary layer parameters. The stability and convergence
of the robotic manipulator control system are guaranteed
by applying the Lyapunov theorem. Simulation results
demonstrate that the chattering of control input can be
alleviated effectively. The proposed controller scheme can
assure robustness against a large class of uncertainties and
achieve good trajectory tracking performance.
Abstract: This paper features the trajectory planning design of a indigenously developed 4-Axis SCARA robot which is used for doing successful robotic manipulation task in the laboratory. Once, a trajectory is being designed and given as input to the robot, the robot's gripper tip moves along that specified trajectory. Trajectories have to be designed in the work space only. The main idea of this paper is to design a continuous path trajectory model for the indigenously developed SCARA robot arm during its maneuvering from one point to another point (during pick and place operations) in a workspace avoiding all the obstacles in its path of motion.
Abstract: This paper presents the voltage regulation scheme of
D-STATCOM under three-phase faults. It consists of the voltage
detection and voltage regulation schemes in the 0dq reference. The
proposed control strategy uses the proportional controller in which
the proportional gain, kp, is appropriately adjusted by using genetic
algorithms. To verify its use, a simplified 4-bus test system is situated
by assuming a three-phase fault at bus 4. As a result, the DSTATCOM
can resume the load voltage to the desired level within
1.8 ms. This confirms that the proposed voltage regulation scheme
performs well under three-phase fault events.
Abstract: In deregulated operating regime power system security is an issue that needs due thoughtfulness from researchers in the horizon of unbundling of generation and transmission. Electric power systems are exposed to various contingencies. Network contingencies often contribute to overloading of branches, violation of voltages and also leading to problems of security/stability. To maintain the security of the systems, it is desirable to estimate the effect of contingencies and pertinent control measurement can be taken on to improve the system security. This paper presents the application of particle swarm optimization algorithm to find the optimal location of multi type FACTS devices in a power system in order to eliminate or alleviate the line over loads. The optimizations are performed on the parameters, namely the location of the devices, their types, their settings and installation cost of FACTS devices for single and multiple contingencies. TCSC, SVC and UPFC are considered and modeled for steady state analysis. The selection of UPFC and TCSC suitable location uses the criteria on the basis of improved system security. The effectiveness of the proposed method is tested for IEEE 6 bus and IEEE 30 bus test systems.
Abstract: Automotive suspension system is important part of car
comfort and safety. In this article automotive active suspension with
linear motor as actuator is designed using H-infinity control. This
paper is focused on comparison of different controller designed for
quart, half or full-car model (and always used for “full" car). Special
attention is placed on energy demand of the whole system. Each
controller configuration is simulated and then verified on the
hydraulic quarter car test bed.
Abstract: This paper discusses the implementation of a fuzzy logic based coordinated voltage control for a distribution system connected with distributed generations (DGs). The connection of DGs has created a challenge for the distribution network operators to keep the voltage in the system within its acceptable limits. Intelligent centralized or coordinated voltage control schemes have proven to be more reliable due to its ability to provide more control and coordination with the communication with other network devices. In this work, voltage control using fuzzy logic by coordinating three methods of control, power factor control, on load tap changer and generation curtailment is implemented on a distribution network test system. The results show that the fuzzy logic based coordination is able to keep the voltage within its allowable limits.
Abstract: Artificial neural networks (ANN) have the ability to model input-output relationships from processing raw data. This characteristic makes them invaluable in industry domains where such knowledge is scarce at best. In the recent decades, in order to overcome the black-box characteristic of ANNs, researchers have attempted to extract the knowledge embedded within ANNs in the form of rules that can be used in inference systems. This paper presents a new technique that is able to extract a small set of rules from a two-layer ANN. The extracted rules yield high classification accuracy when implemented within a fuzzy inference system. The technique targets industry domains that possess less complex problems for which no expert knowledge exists and for which a simpler solution is preferred to a complex one. The proposed technique is more efficient, simple, and applicable than most of the previously proposed techniques.
Abstract: The aim of this paper is to identify an optimum
control strategy of three-phase shunt active filters to minimize the total harmonic distortion factor of the supply current. A classical PIPI cascade control solution of the output current of the active filterand the voltage across the DC capacitor based on Modulus–Optimum
criterion is taken into consideration. The control system operation
has been simulated using Matlab-Simulink environment and the results agree with the theoretical expectation. It is shown that there is
an optimum value of the DC-bus voltage which minimizes the supply current harmonic distortion factor. It corresponds to the equality of the apparent power at the output of the active filter and the apparent power across the capacitor. Finally, predicted results are verified experimentally on a MaxSine active power filter.
Abstract: Any use of energy in industrial productive activities is combined with various environment impacts. Withintransportation,
this fact was not only found among land transport, railways and maritime transport, but also in the air transport industry. An effective climate protection requires strategies and measures for reducing all
greenhouses gas emissions, in particular carbon dioxide, and must
take into account the economic, ecologic and social aspects. It seem simperative now to develop and manufacture environmentally
friendly products and systems, to reduce consumption and use less
resource, and to save energy and power. Today-sproducts could
better serve these requirements taking into account the integration of
a power management system into the electrical power system.This
paper gives an overview of an approach ofpower management with
load prioritization in modernaircraft. Load dimensioning and load
management strategies on current civil aircraft will be presented and
used as a basis for the proposed approach.
Abstract: One of the main objectives of order reduction is to
design a controller of lower order which can effectively control the
original high order system so that the overall system is of lower
order and easy to understand. In this paper, a simple method is
presented for controller design of a higher order discrete system.
First the original higher order discrete system in reduced to a lower
order model. Then a Proportional Integral Derivative (PID)
controller is designed for lower order model. An error minimization
technique is employed for both order reduction and controller
design. For the error minimization purpose, Differential Evolution
(DE) optimization algorithm has been employed. DE method is
based on the minimization of the Integral Squared Error (ISE)
between the desired response and actual response pertaining to a
unit step input. Finally the designed PID controller is connected to
the original higher order discrete system to get the desired
specification. The validity of the proposed method is illustrated
through a numerical example.
Abstract: This paper presents the experimental results on space charge distribution in cross-linked polyethylene (XLPE) insulating material for 22 kV power distribution system cable by using pulse electroacoustic measurement technique (PEA). Numbers of XLPE insulating material ribbon having thickness 60 μm taken from unused 22 kV high voltage cable were used as specimen in this study. DC electric field stress was applied to test specimen at room temperature (25°C). Four levels of electric field stress, 25 kV/mm, 50 kV/mm, 75 kV/mm and 100 kV/mm, were used. In order to investigate space charge distribution characteristic, space charge distribution characteristics were measured after applying electric field stress 15 min, 30 min and 60 min, respectively. The results show that applied time and magnitude of dc electric field stress play an important role to the formation of space charge.
Abstract: Overhead electrical insulators form an important link in an electric power system. Along with the traditional insulators (i.e. glass and porcelain, etc) presently the polymeric insulators are also used world widely. These polymeric insulators are very sensitive to various environmental parameters such temperature, environmental pollution, UV-radiations, etc. which seriously effect their electrical, chemical and hydrophobic properties. The UV radiation level in the central region of Saudi Arabia is high as compared to the IEC standard for the accelerated aging of the composite insulators. Commonly used suspension type of composite EPDM (Ethylene Propylene Diene Monomer) insulator was subjected to accelerated stress aging as per modified IEC standard simulating the inland arid deserts atmospheric condition and also as per IEC-61109 standard. The hydrophobic characteristics were studied by measuring the contact angle along the insulator surface before and after the accelerated aging of the samples. It was found that EPDM insulator loses it hydrophobic properties proportional to the intensity of UV irradiations and its rate of recovery is also very low as compared to Silicone Rubber insulator.KeywordsEPDM, composite insulators, accelerated aging, hydrophobicity, contact angle.
Abstract: An electric utility-s main concern is to plan, design, operate and maintain its power supply to provide an acceptable level of reliability to its users. This clearly requires that standards of reliability be specified and used in all three sectors of the power system, i.e., generation, transmission and distribution. That is why reliability of a power system is always a major concern to power system planners. This paper presents the reliability analysis of Bangladesh Power System (BPS). Reliability index, loss of load probability (LOLP) of BPS is evaluated using recursive algorithm and considering no de-rated states of generators. BPS has sixty one generators and a total installed capacity of 5275 MW. The maximum demand of BPS is about 5000 MW. The relevant data of the generators and hourly load profiles are collected from the National Load Dispatch Center (NLDC) of Bangladesh and reliability index 'LOLP' is assessed for the period of last ten years.