Abstract: Power transformers are among the most important and
expensive equipments in the electric power systems. Consequently
the transformer protection is an essential part of the system
protection. This paper presents a new method for locating
transformer winding faults such as turn-to-turn, turn-to-core, turn-totransformer
body, turn-to-earth, and high voltage winding to low
voltage winding. In this study the current and voltage signals of input
and output terminals of the transformer are measured, which the
Fourier transform of measured signals and harmonic analysis
determine the fault's location.
Abstract: In order to enhance the contrast in the regions where the pixels have similar intensities, this paper presents a new histogram equalization scheme. Conventional global equalization schemes over-equalizes these regions so that too bright or dark pixels are resulted and local equalization schemes produce unexpected discontinuities at the boundaries of the blocks. The proposed algorithm segments the original histogram into sub-histograms with reference to brightness level and equalizes each sub-histogram with the limited extents of equalization considering its mean and variance. The final image is determined as the weighted sum of the equalized images obtained by using the sub-histogram equalizations. By limiting the maximum and minimum ranges of equalization operations on individual sub-histograms, the over-equalization effect is eliminated. Also the result image does not miss feature information in low density histogram region since the remaining these area is applied separating equalization. This paper includes how to determine the segmentation points in the histogram. The proposed algorithm has been tested with more than 100 images having various contrasts in the images and the results are compared to the conventional approaches to show its superiority.
Abstract: In the context of spectrum surveillance, a method to
recover the code of spread spectrum signal is presented, whereas the
receiver has no knowledge of the transmitter-s spreading sequence.
The approach is based on a genetic algorithm (GA), which is forced to
model the received signal. Genetic algorithms (GAs) are well known
for their robustness in solving complex optimization problems.
Experimental results show that the method provides a good
estimation, even when the signal power is below the noise power.
Abstract: A bond graph model of a two degrees of freedom
PUMA is described. System inversion gives the system input
required to generate a given system output. In order to get the system
inversion of the PUMA manipulator, a linearization of the nonlinear
bond graph is obtained. Hence, the bicausality of the linearized bond
graph of the PUMA manipulator is applied. Thus, the bicausal bond
graph provides a systematic way of generating the equations of the
system inversion. Simulation results to verify the calculated input for
a given output are shown.
Abstract: Optimal supplementary damping controller design for Thyristor Controlled Series Compensator (TCSC) is presented in this paper. For the proposed controller design, a multi-objective fitness function consisting of both damping factors and real part of system electromachanical eigenvalue is used and Real- Coded Genetic Algorithm (RCGA) is employed for the optimal supplementary controller parameters. The performance of the designed supplementary TCSC-based damping controller is tested on a weakly connected power system with different disturbances and loading conditions with parameter variations. Simulation results are presented and compared with a conventional power system stabilizer and also with the TCSC-based supplementary controller when the controller parameters are not optimized to show the effectiveness and robustness of the proposed approach over a wide range of loading conditions and disturbances.
Abstract: The evolution of logic circuits, which falls under the heading of evolvable hardware, is carried out by evolutionary algorithms. These algorithms are able to automatically configure reconfigurable devices. One of main difficulties in developing evolvable hardware with the ability to design functional electrical circuits is to choose the most favourable EA features such as fitness function, chromosome representations, population size, genetic operators and individual selection. Until now several researchers from the evolvable hardware community have used and tuned these parameters and various rules on how to select the value of a particular parameter have been proposed. However, to date, no one has presented a study regarding the size of the chromosome representation (circuit layout) to be used as a platform for the evolution in order to increase the evolvability, reduce the number of generations and optimize the digital logic circuits through reducing the number of logic gates. In this paper this topic has been thoroughly investigated and the optimal parameters for these EA features have been proposed. The evolution of logic circuits has been carried out by an extrinsic evolvable hardware system which uses (1+λ) evolution strategy as the core of the evolution.
Abstract: In this paper, we propose a fast and efficient method for drawing very large-scale graph data. The conventional force-directed method proposed by Fruchterman and Rheingold (FR method) is well-known. It defines repulsive forces between every pair of nodes and attractive forces between connected nodes on a edge and calculates corresponding potential energy. An optimal layout is obtained by iteratively updating node positions to minimize the potential energy. Here, the positions of the nodes are updated every global timestep at the same time. In the proposed method, each node has its own individual time and time step, and nodes are updated at different frequencies depending on the local situation. The proposed method is inspired by the hierarchical individual time step method used for the high accuracy calculations for dense particle fields such as star clusters in astrophysical dynamics. Experiments show that the proposed method outperforms the original FR method in both speed and accuracy. We implement the proposed method on the MDGRAPE-3 PCI-X special purpose parallel computer and realize a speed enhancement of several hundred times.
Abstract: Power system stabilizers (PSS) are now routinely used in the industry to damp out power system oscillations. In this paper, real-coded genetic algorithm (RCGA) optimization technique is applied to design robust power system stabilizer for both singlemachine infinite-bus (SMIB) and multi-machine power system. The design problem of the proposed controller is formulated as an optimization problem and RCGA is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. The non-linear simulation results are presented under wide range of operating conditions; disturbances at different locations as well as for various fault clearing sequences to show the effectiveness and robustness of the proposed controller and their ability to provide efficient damping of low frequency oscillations.
Abstract: Removing noise from the any processed images is very important. Noise should be removed in such a way that important information of image should be preserved. A decisionbased nonlinear algorithm for elimination of band lines, drop lines, mark, band lost and impulses in images is presented in this paper. The algorithm performs two simultaneous operations, namely, detection of corrupted pixels and evaluation of new pixels for replacing the corrupted pixels. Removal of these artifacts is achieved without damaging edges and details. However, the restricted window size renders median operation less effective whenever noise is excessive in that case the proposed algorithm automatically switches to mean filtering. The performance of the algorithm is analyzed in terms of Mean Square Error [MSE], Peak-Signal-to-Noise Ratio [PSNR], Signal-to-Noise Ratio Improved [SNRI], Percentage Of Noise Attenuated [PONA], and Percentage Of Spoiled Pixels [POSP]. This is compared with standard algorithms already in use and improved performance of the proposed algorithm is presented. The advantage of the proposed algorithm is that a single algorithm can replace several independent algorithms which are required for removal of different artifacts.
Abstract: For future Broad band ISDN, Asynchronous Transfer
Mode (ATM) is designed not only to support a wide range of traffic
classes with diverse flow characteristics, but also to guarantee the
different quality of service QOS requirements. The QOS may be
measured in terms of cell loss probability and maximum cell delay.
In this paper, ATM networks in which the virtual path (VP)
concept is implemented are considered. By applying the Markov
Deterministic process method, an efficient algorithm to compute the
minimum capacity required to satisfy the QOS requirements when
multiple classes of on-off are multiplexed on to a single VP. Using
the result, we then proposed a simple algorithm to determine different
combinations of VP to achieve the optimum of the total capacity
required for satisfying the individual QOS requirements (loss- delay).
Abstract: This study is concerned with pH solution detection
using 2 × 4 flexible sensor array based on a plastic polyethylene
terephthalate (PET) substrate that is coated a conductive layer and a
ruthenium dioxide (RuO2) sensitive membrane with the technologies
of screen-printing and RF sputtering. For data analysis, we also
prepared a dynamic measurement system for acquiring the response
voltage and analyzing the characteristics of the working electrodes
(WEs), such as sensitivity and linearity. In this condition, an array
measurement system was designed to acquire the original signal from
sensor array, and it is based on the method of digital signal processing
(DSP). The DSP modifies the unstable acquisition data to a direct
current (DC) output using the technique of digital filter. Hence, this
sensor array can obtain a satisfactory yield, 62.5%, through the design
measurement and analysis system in our laboratory.
Abstract: Accurate modeling of high speed RLC interconnects
has become a necessity to address signal integrity issues in current
VLSI design. To accurately model a dispersive system of interconnects
at higher frequencies; a full-wave analysis is required.
However, conventional circuit simulation of interconnects with full
wave models is extremely CPU expensive. We present an algorithm
for reducing large VLSI circuits to much smaller ones with similar
input-output behavior. A key feature of our method, called Frequency
Shift Technique, is that it is capable of reducing linear time-varying
systems. This enables it to capture frequency-translation and sampling
behavior, important in communication subsystems such as mixers,
RF components and switched-capacitor filters. Reduction is obtained
by projecting the original system described by linear differential
equations into a lower dimension. Experiments have been carried out
using Cadence Design Simulator cwhich indicates that the proposed
technique achieves more % reduction with less CPU time than the
other model order reduction techniques existing in literature. We
also present applications to RF circuit subsystems, obtaining size
reductions and evaluation speedups of orders of magnitude with
insignificant loss of accuracy.
Abstract: In this paper, we proposed an invention of an
accessory into a communication device that will help humans to be
connected universally. Generally, this device will be made up of
crystal and will combine many technologies that will enable the user
to run various applications and software anywhere and everywhere.
Bringing up the concept of from being user friendly, we had used the
crystal as the main material of the device that will trap the
surrounding lights to produce projection of its screen. This leads to a
lesser energy consumption and allows smaller sized battery to be
used, making the device less bulky. Additionally, we proposed the
usage of micro batteries as our energy source. Thus, researches
regarding crystal were made along with explanations in details of
specification and function of the technology used in the device.
Finally, we had also drawn several views of the invention from
different sides to be visualized.
Abstract: Estimating the reliability of a computer network has been a subject of great interest. It is a well known fact that this problem is NP-hard. In this paper we present a very efficient combinatorial approach for Monte Carlo reliability estimation of a network with unreliable nodes and unreliable edges. Its core is the computation of some network combinatorial invariants. These invariants, once computed, directly provide pure and simple framework for computation of network reliability. As a specific case of this approach we obtain tight lower and upper bounds for distributed network reliability (the so called residual connectedness reliability). We also present some simulation results.
Abstract: In neural networks, when new patterns are learned by a network, the new information radically interferes with previously stored patterns. This drawback is called catastrophic forgetting or catastrophic interference. In this paper, we propose a biologically inspired neural network model which overcomes this problem. The proposed model consists of two distinct networks: one is a Hopfield type of chaotic associative memory and the other is a multilayer neural network. We consider that these networks correspond to the hippocampus and the neocortex of the brain, respectively. Information given is firstly stored in the hippocampal network with fast learning algorithm. Then the stored information is recalled by chaotic behavior of each neuron in the hippocampal network. Finally, it is consolidated in the neocortical network by using pseudopatterns. Computer simulation results show that the proposed model has much better ability to avoid catastrophic forgetting in comparison with conventional models.
Abstract: In today scenario, to meet enhanced demand imposed
by domestic, commercial and industrial consumers, various
operational & control activities of Radial Distribution Network
(RDN) requires a focused attention. Irrespective of sub-domains
research aspects of RDN like network reconfiguration, reactive
power compensation and economic load scheduling etc, network
performance parameters are usually estimated by an iterative process
and is commonly known as load (power) flow algorithm. In this
paper, a simple mechanism is presented to implement the load flow
analysis (LFA) algorithm. The reported algorithm utilizes graph
theory principles and is tested on a 69- bus RDN.
Abstract: Analysis of heart rate variability (HRV) has become a
popular non-invasive tool for assessing the activities of autonomic
nervous system. Most of the methods were hired from techniques
used for time series analysis. Currently used methods are time
domain, frequency domain, geometrical and fractal methods. A new
technique, which searches for pattern repeatability in a time series, is
proposed for quantifying heart rate (HR) time series. These set of
indices, which are termed as pattern repeatability measure and
pattern repeatability ratio are able to distinguish HR data clearly
from noise and electroencephalogram (EEG). The results of analysis
using these measures give an insight into the fundamental difference
between the composition of HR time series with respect to EEG and
noise.
Abstract: This paper presents design, analysis and comparison of the different rotor type permanent magnet machines. The presented machines are designed as having same geometrical dimensions and same materials for comparison. The main machine parameters of interior and exterior rotor type machines including eddy current effect, torque-speed characteristics and magnetic analysis are investigated using MAXWELL program. With this program, the components of the permanent magnet machines can be calculated with high accuracy. Six types of Permanent machines are compared with respect to their topology, size, magnetic field, air gap flux, voltage, torque, loss and efficiency. The analysis results demonstrate the effectiveness of the proposed machines design methodology. We believe that, this study will be a helpful resource in terms of examination and comparison of the basic structure and magnetic features of the PM (Permanent magnet) machines which have different rotor structure.
Abstract: This paper presents a simple method for estimation of
additional load as a factor of the existing load that may be drawn
before reaching the point of line maximum loadability of radial
distribution system (RDS) with different realistic load models at
different substation voltages. The proposed method involves a simple
line loadability index (LLI) that gives a measure of the proximity of
the present state of a line in the distribution system. The LLI can use
to assess voltage instability and the line loading margin. The
proposed method also compares with the existing method of
maximum loadability index [10]. The simulation results show that the
LLI can identify not only the weakest line/branch causing system
instability but also the system voltage collapse point when it is near
one. This feature enables us to set an index threshold to monitor and
predict system stability on-line so that a proper action can be taken to
prevent the system from collapse. To demonstrate the validity of the
proposed algorithm, computer simulations are carried out on two bus
and 69 bus RDS.
Abstract: Super-resolution is nowadays used for a high-resolution
image produced from several low-resolution noisy frames. In
this work, we consider the problem of high-quality interpolation of a
single noise-free image. Such images may come from different sources,
i.e., they may be frames of videos, individual pictures, etc. On
the other hand, in the encoder we apply a downsampling via
bidimen-sional interpolation of each frame, and in the decoder we
apply a upsampling by which we restore the original size of the
image. If the compression ratio is very high, then we use a
convolutive mask that restores the edges, eliminating the blur.
Finally, both, the encoder and the complete decoder are implemented
on General-Purpose computation on Graphics Processing Units
(GPGPU) cards. In fact, the mentioned mask is coded inside texture
memory of a GPGPU.