Abstract: This paper presents the experimental results of silicone rubber polymer insulators for 22 kV systems under salt water dip wheel test based on IEC 62217. Straight shed silicone rubber polymer insulators having leakage distance 685 mm were tested continuously 30,000 cycles. One test cycle includes 4 positions, energized, de-energized, salt water dip and deenergized, respectively. For one test cycle, each test specimen remains stationary for about 40 second in each position and takes 8 second for rotate to next position. By visual observation, sever surface erosion was observed on the trunk near the energized end of tested specimen. Puncture was observed on the upper shed near the energized end. In addition, decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Furthermore, chemical analysis by ATR-FTIR was conducted in order to elucidate the chemical change of tested specimens comparing with new specimen.
Abstract: Temperature rise in a transformer depends on variety
of parameters such as ambient temperature, output current and type
of the core. Considering these parameters, temperature rise estimation
is still complicated procedure. In this paper, we present a new model
based on simple electrical equivalent circuit. This method avoids the
complication associated to accurate estimation and is in very good
agreement with practice.
Abstract: In order to perform on-line measuring and detection
of PD signals, a total solution composing of an HFCT, A/D
converter and a complete software package is proposed. The
software package includes compensation of HFCT contribution,
filtering and noise reduction using wavelet transform and soft
calibration routines. The results have shown good performance and
high accuracy.
Abstract: A model predictive controller based on recursive learning is proposed. In this SISO adaptive controller, a model is automatically updated using simple recursive equations. The identified models are then stored in the memory to be re-used in the future. The decision for model update is taken based on a new control performance index. The new controller allows the use of simple linear model predictive controllers in the control of nonlinear time varying processes.
Abstract: This paper presents the significant factor and give
some suggestion that should know before design. The main objective of this paper is guide the first step for someone who attends to design of grounding system before study in details later. The overview of
grounding system can protect damage from fault such as can save a human life and power system equipment. The unsafe conditions have
three cases. Case 1) maximum touch voltage exceeds the safety
criteria. In this case, the conductor compression ratio of the ground gird should be first adjusted to have optimal spacing of ground grid
conductors. If it still over limit, earth resistivity should be consider afterward. Case 2) maximum step voltage exceeds the safety criteria.
In this case, increasing the number of ground grid conductors around
the boundary can solve this problem. Case 3) both of maximum touch
and step voltage exceed the safety criteria. In this case, follow the solutions explained in case 1 and case 2. Another suggestion, vary depth of ground grid until maximum step and touch voltage do not
exceed the safety criteria.
Abstract: High speed networks provide realtime variable bit rate
service with diversified traffic flow characteristics and quality
requirements. The variable bit rate traffic has stringent delay and
packet loss requirements. The burstiness of the correlated traffic
makes dynamic buffer management highly desirable to satisfy the
Quality of Service (QoS) requirements. This paper presents an
algorithm for optimization of adaptive buffer allocation scheme for
traffic based on loss of consecutive packets in data-stream and buffer
occupancy level. Buffer is designed to allow the input traffic to be
partitioned into different priority classes and based on the input
traffic behavior it controls the threshold dynamically. This algorithm
allows input packets to enter into buffer if its occupancy level is less
than the threshold value for priority of that packet. The threshold is
dynamically varied in runtime based on packet loss behavior. The
simulation is run for two priority classes of the input traffic –
realtime and non-realtime classes. The simulation results show that
Adaptive Partial Buffer Sharing (ADPBS) has better performance
than Static Partial Buffer Sharing (SPBS) and First In First Out
(FIFO) queue under the same traffic conditions.
Abstract: This paper describes a CMOS four-quadrant
multiplier intended for use in the front-end receiver by utilizing the
square-law characteristic of the MOS transistor in the saturation
region. The circuit is based on 0.35 um CMOS technology simulated
using HSPICE software. The mixer has a third-order inter the power
consumption is 271uW from a single 1.2V power supply. One of the
features of the proposed design is using two MOS transistors
limitation to reduce the supply voltage, which leads to reduce the
power consumption. This technique provides a GHz bandwidth
response and low power consumption.
Abstract: This paper presents two simplified models to
determine nodal voltages in power distribution networks. These
models allow estimating the impact of the installation of reactive
power compensations equipments like fixed or switched capacitor
banks. The procedure used to develop the models is similar to the
procedure used to develop linear power flow models of transmission
lines, which have been widely used in optimization problems of
operation planning and system expansion. The steady state non-linear
load flow equations are approximated by linear equations relating the
voltage amplitude and currents. The approximations of the linear
equations are based on the high relationship between line resistance
and line reactance (ratio R/X), which is valid for power distribution
networks. The performance and accuracy of the models are evaluated
through comparisons with the exact results obtained from the
solution of the load flow using two test networks: a hypothetical
network with 23 nodes and a real network with 217 nodes.
Abstract: Today with the rapid growth of telecommunications equipment, electronic and developing more and more networks of power, influence of electromagnetic waves on one another has become hot topic discussions. So in this article, this issue and appropriate mechanisms for EMC operations have been presented. First, impact of high voltage lines on the surrounding environment especially on the control room has been investigated, then to reduce electromagnetic radiation, various methods of shielding are provided and shielding effectiveness of them has been compared. It should be expressed that simulations have been done by the finite element method (FEM).
Abstract: This paper presents modeling and simulation of Grid Connected Photovoltaic (PV) system by using improved mathematical model. The model is used to study different parameter variations and effects on the PV array including operating temperature and solar irradiation level. In this paper stepped P&O algorithm is proposed for MPPT control. This algorithm will identify the suitable duty ratio in which the DC-DC converter should be operated to maximize the power output. Photo voltaic array with proposed stepped P&O-MPPT controller can operate in the maximum power point for the whole range of solar data (irradiance and temperature).
Abstract: This paper presents the impact study of GTO Controlled Series Capacitor (GCSC) parameters on measured impedance (Zseen) by MHO distance relays for single transmission line high voltage 220 kV in the presence of single phase to earth fault with fault resistance (RF). The study deals with a 220 kV single electrical transmission line of Eastern Algerian transmission networks at Group Sonelgaz (Algerian Company of Electrical and Gas) compensated by series Flexible AC Transmission System (FACTS) i.e. GCSC connected at midpoint of the transmission line. The transmitted active and reactive powers are controlled by three GCSC-s. The effects of maximum reactive power injected as well as injected maximum voltage by GCSC on distance relays measured impedance is treated. The simulations results investigate the effects of GCSC injected parameters: variable reactance (XGCSC), variable voltage (VGCSC) and reactive power injected (QGCSC) on measured resistance and reactance in the presence of earth fault with resistance fault varied between 5 to 50 Ω for three cases study.
Abstract: This paper explains a project based learning method where autonomous mini-robots are developed for research, education and entertainment purposes. In case of remote systems wireless sensors are developed in critical areas, which would collect data at specific time intervals, send the data to the central wireless node based on certain preferred information would make decisions to turn on or off a switch or control unit. Such information transfers hardly sums up to a few bytes and hence low data rates would suffice for such implementations. As a robot is a multidisciplinary platform, the interfacing issues involved are discussed in this paper. The paper is mainly focused on power supply, grounding and decoupling issues.
Abstract: This paper presents a reliability-based approach to select appropriate wind turbine types for a wind farm considering site-specific wind speed patterns. An actual wind farm in the northern region of Iran with the wind speed registration of one year is studied in this paper. An analytic approach based on total probability theorem is utilized in this paper to model the probabilistic behavior of both turbines- availability and wind speed. Well-known probabilistic reliability indices such as loss of load expectation (LOLE), expected energy not supplied (EENS) and incremental peak load carrying capability (IPLCC) for wind power integration in the Roy Billinton Test System (RBTS) are examined. The most appropriate turbine type achieving the highest reliability level is chosen for the studied wind farm.
Abstract: The speech signal conveys information about the
identity of the speaker. The area of speaker identification is
concerned with extracting the identity of the person speaking the
utterance. As speech interaction with computers becomes more
pervasive in activities such as the telephone, financial transactions
and information retrieval from speech databases, the utility of
automatically identifying a speaker is based solely on vocal
characteristic. This paper emphasizes on text dependent speaker
identification, which deals with detecting a particular speaker from a
known population. The system prompts the user to provide speech
utterance. System identifies the user by comparing the codebook of
speech utterance with those of the stored in the database and lists,
which contain the most likely speakers, could have given that speech
utterance. The speech signal is recorded for N speakers further the
features are extracted. Feature extraction is done by means of LPC
coefficients, calculating AMDF, and DFT. The neural network is
trained by applying these features as input parameters. The features
are stored in templates for further comparison. The features for the
speaker who has to be identified are extracted and compared with the
stored templates using Back Propogation Algorithm. Here, the
trained network corresponds to the output; the input is the extracted
features of the speaker to be identified. The network does the weight
adjustment and the best match is found to identify the speaker. The
number of epochs required to get the target decides the network
performance.
Abstract: The paper considers a single-server queue with fixedsize
batch Poisson arrivals and exponential service times, a model
that is useful for a buffer that accepts messages arriving as fixed size
batches of packets and releases them one packet at time. Transient
performance measures for queues have long been recognized as
being complementary to the steady-state analysis. The focus of the
paper is on the use of the functions that arise in the analysis of the
transient behaviour of the queuing system. The paper exploits
practical modelling to obtain a solution to the integral equation
encountered in the analysis. Results obtained indicate that under
heavy load conditions, there is significant disparity in the statistics
between the transient and steady state values.
Abstract: Condition monitoring of electrical power equipment
has attracted considerable attention for many years. The aim of this
paper is to use Labview with Fuzzy Logic controller to build a
simulation system to diagnose transformer faults and monitor its
condition. The front panel of the system was designed using
LabVIEW to enable computer to act as customer-designed
instrument. The dissolved gas-in-oil analysis (DGA) method was
used as technique for oil type transformer diagnosis; meanwhile
terminal voltages and currents analysis method was used for dry type
transformer. Fuzzy Logic was used as expert system that assesses all
information keyed in at the front panel to diagnose and predict the
condition of the transformer. The outcome of the Fuzzy Logic
interpretation will be displayed at front panel of LabVIEW to show
the user the conditions of the transformer at any time.
Abstract: In this paper, the authors take a look at advantages of
multiphase induction motors comparing them with three phase ones
and present the applications where six-phase induction motors are
used. They elaborate the mathematical model of six-phase induction
motor with two similar stator three phase winding, shifted by 30
degrees in space and three phase winding in rotor, in synchronous
reference frame for soft starting and scalar control. The authors
simulate and discuss results of speed and torque starting transients.
Abstract: In working mode some unexpected changes could
be arise in inner structure of electromagnetic device. They
influence modification in electromagnetic field propagation map.
The field values at an observed boundary are also changed. The
development of the process has to be watched because the arising
structural changes would provoke the device to be gone out later.
The probabilistic assessment of the state is possible to be made.
The numerical assessment points if the resulting changes have
only accidental character or they are due to the essential inner
structural disturbances.
The presented application example is referring to the 200MW
turbine-generator. A part of the stator core end teeth zone is
simulated broken. Quasi three-dimensional electromagnetic and
temperature field are solved applying FEM. The stator core state
diagnosis is proposed to be solved as an identification problem on
the basis of a statistical criterion.
Abstract: In this paper we consider the issue of distributed adaptive estimation over sensor networks. To deal with more realistic scenario, different variance for observation noise is assumed for sensors in the network. To solve the problem of different variance of observation noise, the proposed method is divided into two phases: I) Estimating each sensor-s observation noise variance and II) using the estimated variances to obtain the desired parameter. Our proposed algorithm is based on a diffusion least mean square (LMS) implementation with linear combiner model. In the proposed algorithm, the step-size parameter the coefficients of linear combiner are adjusted according to estimated observation noise variances. As the simulation results show, the proposed algorithm considerably improves the diffusion LMS algorithm given in literature.
Abstract: This paper proposes a method of adaptively generating a gait pattern of biped robot. The gait synthesis is based on human's gait pattern analysis. The proposed method can easily be applied to generate the natural and stable gait pattern of any biped robot. To analyze the human's gait pattern, sequential images of the human's gait on the sagittal plane are acquired from which the gait control values are extracted. The gait pattern of biped robot on the sagittal plane is adaptively generated by a genetic algorithm using the human's gait control values. However, gait trajectories of the biped robot on the sagittal plane are not enough to construct the complete gait pattern because the biped robot moves on 3-dimension space. Therefore, the gait pattern on the frontal plane, generated from Zero Moment Point (ZMP), is added to the gait one acquired on the sagittal plane. Consequently, the natural and stable walking pattern for the biped robot is obtained.