Abstract: Wireless mesh networks based on IEEE 802.11
technology are a scalable and efficient solution for next generation
wireless networking to provide wide-area wideband internet access to
a significant number of users. The deployment of these wireless mesh
networks may be within different authorities and without any
planning, they are potentially overlapped partially or completely in
the same service area. The aim of the proposed model is design a new
model to Enhancement Throughput of Unplanned Wireless Mesh
Networks Deployment Using Partitioning Hierarchical Cluster
(PHC), the unplanned deployment of WMNs are determinates there
performance. We use throughput optimization approach to model the
unplanned WMNs deployment problem based on partitioning
hierarchical cluster (PHC) based architecture, in this paper the
researcher used bridge node by allowing interworking traffic between
these WMNs as solution for performance degradation.
Abstract: Phase transformation temperature is one of the most important parameters for the shape memory alloys (SMAs). The most popular method to determine these phase transformation temperatures is the Differential Scanning Calorimeter (DSC), but due to the limitation of the DSC testing itself, it made it difficult for the finished product which is not in the powder form. A novel method which uses the Universal Testing Machine has been conducted to determine the phase transformation temperatures. The Flexinol wire was applied with force and maintained throughout the experiment and at the same time it was heated up slowly until a temperature of approximately 1000C with direct current. The direct current was then slowly decreased to cool down the temperature of the Flexinol wire. All the phase transformation temperatures for Flexinol wire were obtained. The austenite start at 52.540C and austenite finish at 60.900C, while martensite start at 44.780C and martensite finish at 32.840C.
Abstract: Air conditioning is mainly to be used as human
comfort medium. It has been use more often in country in which the
daily temperatures are high. In scientific, air conditioning is defined
as a process of controlling the moisture, cooling, heating and cleaning
air. Without proper estimation of cooling load, big amount of waste
energy been used because of unsuitable of air conditioning system are
not considering to overcoming heat gains from surrounding. This is
due to the size of the room is too big and the air conditioning has to
use more energy to cool the room and the air conditioning is too
small for the room. The studies are basically to develop a program to
calculate cooling load. Through this study it is easy to calculate
cooling load estimation. Furthermore it-s help to compare the cooling
load estimation by hourly and yearly. Base on the last study that been
done, the developed software are not user-friendly. For individual
without proper knowledge of calculating cooling load estimation
might be problem. Easy excess and user-friendly should be the main
objective to design something. This program will allow cooling load
able be estimate by any users rather than estimation by using rule of
thumb. Several of limitation of case study is judged to sure it-s
meeting to Malaysia building specification. Finally validation is done
by comparison manual calculation and by developed program.
Abstract: Antimicrobial (AM) starch-based films were
developed by incorporating chitosan and lauric acid as antimicrobial
agent into starch-based film. Chitosan has wide range of applications
as a biomaterial, but barriers still exist to its broader use due to its
physical and chemical limitations. In this work, a series of
starch/chitosan (SC) blend films containing 8% of lauric acid was
prepared by casting method. The structure of the film was
characterized by Fourier transform infrared spectroscopy (FTIR), Xray
diffraction (XRD), and scanning electron microscopy (SEM).
The results indicated that there were strong interactions were present
between the hydroxyl groups of starch and the amino groups of
chitosan resulting in a good miscibility between starch and chitosan
in the blend films. Physical properties and optical properties of the
AM starch-based film were evaluated. The AM starch-based films
incorporated with chitosan and lauric acid showed an improvement in
water vapour transmission rate (WVTR) and addition of starch
content provided more transparent films while the yellowness of the
film attributed to the higher chitosan content. The improvement in
water barrier properties was mainly attributed to the hydrophobicity
of lauric acid and optimum chitosan or starch content. AM starch
based film also showed excellent oxygen barrier. Obtaining films
with good oxygen permeability would be an indication of the
potential use of these antimicrobial packaging as a natural packaging
and an alternative packaging to the synthetic polymer to protect food
from oxidation reactions
Abstract: This research focuses on micro-enterprise of
Malaysian Malays that are involved in very small-scaled business
activities. Among them include food stall and burger stall operators,
night market hawkers, grocery store operators as well as construction
and small service activities works. The study seeks to explore why
some micro-entrepreneurs still lag in entrepreneurship and what
needs to be rectified. This quantitative study is conducted on 173
Malay micro-enterprise owners (MEOs) and 58 Malay failed microenterprise
owners (FMEOs) involved in all range of businesses
throughout the state of Perak, Malaysia. The main aims are to
identify the gaps between the failed micro-enterprise owners
(FMEOs) and existing micro-enterprise owners (MEOs) and the
problems faced among FMEOs. The results reveal that the MEOs had
strong motivations and better marketing approaches as compared to
FMEOs. Furthermore, the FMEOs failed in the business ventures
mainly due to lack of management, sales and marketing skills and
poor competitive abilities to keep up with rivals.
Abstract: Phytases (myo-inositol hexakisphosphate
phosphohydrolases; EC 3.1.3.8) catalyze the hydrolysis of phytic acid
(myoinositol hexakisphosphate) to the mono-, di-, tri-, tetra-, and
pentaphosphates of myo-inositol and inorganic phosphate.
Therrmophilic bacteria isolated from water sampled from hot spring.
About 120 isolates of bacteria were successfully isolated form hot
spring water sample and tested for extracellular phytase producing.
After 5 passages of the screening on the PSM media, 4 isolates were
found stable in producing phytase enzyme. The 16s RDNA
sequencing for identification of bacteria using molecular technique
revealed that all isolates those positive in phytase producing are
belong to Geobacillus spp. And Anoxybacillus spp. Anoxybacillus
rupiensis UniSZA-7 were identified for their carbon source utilization
using Phenotype Microarray Plate of Biolog and found they utilize
several kind of carbon source provided.
Abstract: One year (November 2009-October 2010) sediment monitoring was used to evaluate pollution status, concentration and distribution of heavy metals (As, Cu, Cd, Cr, Hg, Ni, Pb and Zn) in West Port of Malaysia. Sediment sample were collected from nine stations every four months. Geo-accumulation factor and Pollution Load Index (PLI) were estimated to better understand the pollution level in study area. The heavy metal concentration (Mg/g dry weight) were ranged from 20.2 to 162 for As, 7.4 to 27.6 for Cu, 0.244 to 3.53 for Cd, 11.5 to 61.5 for Cr, 0.11 to 0.409 for Hg, 7.2 to 22.2 for Ni, 22.3 to 80 for Pb and 23 to 98.3 for Zn. In general, concentration some metals (As,Cd, Hg and Pb) was higher than background values that are considered as serious concern for aquatic life and the human health.
Abstract: Current air conditioning system is using refrigerant as
the cooling medium. The main purpose of this study is to develop an
air conditioning system using chill water as the cooling medium. In
this system, chill water used to replace refrigerant as the cooling
medium. This study is focus on the split type unit air conditioning
system only. It will be involving some renovation on the indoor unit
and freezer. The cooling capability of this system was validate by few
series of testing, which conducted at standard 36m3 office room.
Result of the testing found that 0.1 m3 of chill water is able to
maintain the room temperature within standard up to 4 ~ 8 hours. It
expected able to maintain room temperature up to 10 hour with some
improvement.
Abstract: The study investigated the effects of Teaching Games
for Understanding approach on students ‘cognitive learning outcome.
The study was a quasi-experimental non-equivalent pretest-posttest
control group design whereby 10 year old primary school students
(n=72) were randomly assigned to an experimental and a control
group. The experimental group students were exposed with TGfU
approach and the control group with the Traditional Skill approach of
handball game. Game Performance Assessment Instrument (GPAI)
was used to measure students' tactical understanding and decision
making in 3 versus 3 handball game situations. Analysis of
covariance (ANCOVA) was used to analyze the data. The results
reveal that there was a significant difference between the TGfU
approach group and the traditional skill approach group students on
post test score (F (1, 69) = 248.83, p < .05). The findings of this
study suggested the importance of TGfU approach to improve
primary students’ tactical understanding and decision making in
handball game.
Abstract: The thermal expansion behaviour of silicon carbide
(SCS-2) fibre reinforced 6061 aluminium matrix composite subjected
to the influenced thermal mechanical cycling (TMC) process were
investigated. The thermal stress has important effect on the
longitudinal thermal expansion coefficient of the composites. The
present paper used experimental data of the thermal expansion
behaviour of a SiC/Al composite for temperatures up to 370°C, in
which their data was used for carrying out modelling of theoretical
predictions.
Abstract: Integrated Total Quality Management (TQM) with
Lean Manufacturing (LM) is a system comprises of TQM with LM
principles and is associated with financial and nonfinancial
performance measurement indicators. The ultimate goal of this
system is to focus on achieving total customer satisfaction by
removing eight wastes available in any process in an organization.
A survey questionnaire was developed and distributed to 30 highly
active automotive vendors in Malaysia and analyzed by PASW
Statistics 18. It was found out that these vendors have been
practicing and measuring the effectiveness TQM and LM
implementation. More involvement of all Malaysian automotive
vendors will represent the exact status of current Malaysian
automotive industry in implementing TQM and LM and can
determine whether the industry is ready for integrated TQM and
LM system. This is the first study that combined 4 awards
practices, ISO/TS16949, Toyota Production System and
SAEJ4000.
Abstract: Eight heavy metals (Cu, Cr, Zn, Hg, Pb, Cd, Ni and As) were analyzed in sediment samples in the dry and wet seasons from November 2009 to October 2010 in West Port of Peninsular Malaysia. The heavy metal concentrations (mg/kg dry weight) were ranged from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. Metals concentrations in dry season were higher than the rainy season except in cupper and chromium. Analysis of variance with Statistical Analysis System (SAS) shows that the mean concentration of metals in the two seasons (α level=0.05) are not significantly different which shows that the metals were held firmly in the matrix of sediment. Also there are significant differences between control point station with other stations. According to the Interim Sediment Quality guidelines (ISQG), the metal concentrations are moderately polluted, except in arsenic which shows the highest level of pollution.
Abstract: The coastal sediments of West Port of Malaysia was monitored from Nov. 2009 to Oct. 2010 to assess spatial distribution of heavy metals As, Cu, Cd, Cr, Hg, Ni, Zn and Pb. Sediment samples were collected from 10 stations in dry and rainy season in West Port. The range concentrations measured (Mg/g dry weight ) were from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. The geochemical indexes used in this study were Geoaccumulation (Igeo), Contamination Factor (CF) and Pollution Load Index (PLI); these indexes were used to evaluate the levels of sediment contaminations. The results of these indexes show that, the status of West Port sediment quality are moderately polluted by heavy metals except in arsenic which shows the high level of pollution.
Abstract: Service quality has become a centerpiece for airline companies in vying with one another and keeps their image in the minds of passengers. Many airlines have pushed service quality through service personalization which includes both ground and on board especially from the viewpoint of retaining satisfied passengers and attracting new ones. Besides those, in-flight meals/food service is another important aspect of the airline operation. The in flight meals/food services now are seen as part of marketing strategies in attracting business or leisure travelers. This study reports the outcomes of the investigation on in-flight meals/food attributes toward passengers- level of satisfaction and re-flying intention. Taste, freshness, appearance of in-flight meals/food served and menu choices are important to the airlines passengers especially for the long haul flight. Food not only contributes to the prediction of the airline passengers- levels of satisfaction but besides other factors slightly influence passengers- re- flying intention. Airline companies therefore should not ignore this element but take the opportunity to create more attractive and acceptable in-flight meals/food along with other matter as marketing tools in attracting passengers to re-flying with them.
Abstract: High employee turnover rate in Malaysia-s retail industry has become a major issue that needs to be addressed. This study determines the levels of job satisfaction, organizational commitment, and turnover intention of employees in a retail company in Malaysia. The relationships between job satisfaction and organizational commitment on turnover intention are also investigated. A questionnaire was developed using Job Descriptive Index, Organizational Commitment Questionnaire, and Lee and Mowday-s turnover intention items and data were collected from 62 respondents. The findings suggested that the respondents were moderately satisfied with job satisfaction facets such as promotion, work itself, co-workers, and supervisors but were unsatisfied with salary. They also had moderate commitment level with considerably high intention to leave the organization. All satisfaction facets (except for co-workers) and organizational commitment were significantly and negatively related to turnover intention. Based on the findings, retention strategies of retail employees were proposed.
Abstract: Information technology managers nowadays are
facing with tremendous pressure to plan, implement, and adopt new
technology solution due to the rapidity of technology changes.
Resulted from a lack of study that have been done in this topic, the
aim of this paper is to provide a comparison review on current tools
that are currently being used in order to respond to technological
changes. The study is based on extensive literature review of
published works with majority of them are ranging from 2000 to the
first part of 2011. The works were gathered from journals, books,
and other information sources available on the Web. Findings show
that, each tools has different focus and none of the tools are
providing a framework in holistic view, which should include
technical, people, process, and business environment aspect. Hence,
this result provides potential information about current available
tools that IT managers could use to manage changes in technology.
Further, the result reveals a research gap in the area where the
industries a short of such framework.
Abstract: Technical laboratories are typically considered as
highly hazardous places in the polytechnic institution when
addressing the problems of high incidences and fatality rates. In
conjunction with several topics covered in the technical curricular,
safety and health precaution should be highlighted in order to
connect to few key ideas of being safe. Therefore the assessment of
safety awareness in terms of safety and health about hazardous and
risks at laboratories is needed and has to be incorporated with
technical education and other training programmes. The purpose of
this study was to determine the efficacy of technical laboratory safety
in one of the polytechnics in northern region. The study examined
three related issues that were; the availability of safety material and
equipment, safety practice adopted by technical teachers and
administrator-s safety attitudes in enforcing safety to the students. A
model of efficacy technical laboratory was developed to test the
linear relationship between existing safety material and equipment,
teachers- safety practice and administrators- attitude in enforcing
safety and to identify which of technical laboratory safety issues was
the most pertinent factor to realize safety in technical laboratory.
This was done by analyzing survey-based data sets particularly those
obtained from samples of 210 students in the polytechnic. The
Pearson Correlation was used to measure the association between the
variables and to test the research hypotheses. The result of the study
has found that there was a significant correlation between existing
safety material and equipment, safety practice adopted by teacher
and administrator-s attitude. There was also a significant relationship
between technical laboratory safety and safety practice adopted by
teacher and between technical laboratory safety and administrator
attitude. Hence, safety practice adopted by teacher and administrator
attitude is vital in realizing technical laboratory safety.
Abstract: This paper reports on the influence of surface-treated coarse recycled concrete aggregate (RCA) on developing the compressive strength of concrete. The coarse RCA was initially treated by separately impregnating it in calcium metasilicate (CM) or wollastonite and nanosilica (NS) prepared at various concentrations. The effects of both treatment materials on concrete properties (e.g., slump, density and compressive strength) were evaluated. Scanning electron microscopy (SEM) analysis was performed to examine the microstructure of the resulting concrete. Results show that the effective use of treated coarse RCA significantly enhances the compressive strength of concrete. This result is supported by the SEM analysis, which indicates the formation of a dense interface between the treated coarse RCA and the cement matrix. Coarse RCA impregnated in CM solution results in better concrete strength than NS, and the optimum concentration of CM solution recommended for treated coarse RCA is 10%.
Abstract: Mercury is a natural occurring element and present in
various concentrations in the environment. Due to its toxic effects, it
is desirable to research mercury sensitive materials to adsorb
mercury. This paper describes the preparation of Au nanoparticles for
mercury adsorption by using a microwave (MW)-polyol method in
the presence of three different Sodium Chloride (NaCl)
concentrations (10, 20 and 30 mM). Mixtures of spherical, triangular,
octahedral, decahedral particles and 1-D product were obtained using
this rapid method. Sizes and shapes was found strongly depend on the
concentrations of NaCl. Without NaCl concentration, spherical,
triangular plates, octahedral, decahedral nanoparticles and 1D
product were produced. At the lower NaCl concentration (10 mM),
spherical, octahedral and decahedral nanoparticles were present,
while spherical and decahedral nanoparticles were preferentially form
by using 20 mM of NaCl concentration. Spherical, triangular plates,
octahedral and decahedral nanoparticles were obtained at the highest
NaCl concentration (30 mM). The amount of mercury adsorbed using
20 ppm mercury solution is the highest (67.5 %) for NaCl
concentration of 30 mM. The high yield of polygonal particles will
increase the mercury adsorption. In addition, the adsorption of
mercury is also due to the sizes of the particles. The sizes of particles
become smaller with increasing NaCl concentrations (size ranges, 5-
16 nm) than those synthesized without addition of NaCl (size ranges
11-32 nm). It is concluded that NaCl concentrations affects the
formation of sizes and shapes of Au nanoparticles thus affects the
mercury adsorption.
Abstract: The pollution of sediments sampled from the North
Port by polycyclic aromatic hydrocarbons (PAHs) was investigated.
Concentrations of PAHs estimated in the port sediments ranged from
199 to 2851.2 μg/kg dw. The highest concentration was found which
is closed to the Berth line, this locations affected by intensive
shipping activities and Land based runoff and they were dominated
by the high molecular weight PAHs (4–6- rings). Source
identification showed that PAHs originated mostly from the
pyrogenic source either from the combustion of fossil fuels, grass,
wood and coal (majority of the samples). Ecological Risk Assessment
on the port sediments presented that slightly adverse ecological
effects to biological community are expected to occur at the vicinity
of the stations 1 and 4. Thus PAHs are not considered as pollutants of
concern in the North Port.