Abstract: The statistical study has become indispensable for various fields of knowledge. Not any different, in Geotechnics the study of probabilistic and statistical methods has gained power considering its use in characterizing the uncertainties inherent in soil properties. One of the situations where engineers are constantly faced is the definition of a probability distribution that represents significantly the sampled data. To be able to discard bad distributions, goodness-of-fit tests are necessary. In this paper, three non-parametric goodness-of-fit tests are applied to a data set computationally generated to test the goodness-of-fit of them to a series of known distributions. It is shown that the use of normal distribution does not always provide satisfactory results regarding physical and behavioral representation of the modeled parameters.
Abstract: The occurrences of precipitation, also commonly
referred as rain, in the form of "convective" and "stratiform" have
been identified to exist worldwide. In this study, the radar return
echoes or known as reflectivity values acquired from radar scans
have been exploited in the process of classifying the type of rain
endured. The investigation use radar data from Malaysian
Meteorology Department (MMD). It is possible to discriminate the
types of rain experienced in tropical region by observing the vertical
characteristics of the rain structure. .Heavy rain in tropical region
profoundly affects radiowave signals, causing transmission
interference and signal fading. Required wireless system fade margin
depends on the type of rain. Information relating to the two
mentioned types of rain is critical for the system engineers and
researchers in their endeavour to improve the reliability of
communication links. This paper highlights the quantification of
percentage occurrences over one year period in 2009.
Abstract: Environmental concerns about the scarcity of marine
resources are critical driving forces for firms aiming to prepare their
supply chains for sustainability. Building on previous work, this
paper highlights the implementation of good practices geared towards
sustainable operations in the seafood department, which were
pursued in an exploratory retailer case. Outcomes of the adopted
environmentally and socially acceptable fish retailing strategies,
ranged from traceability, to self-certification and eco-labelling. The
consequences for business were, as follows: stronger collaboration
and trust across the chain of custody, improvement of sponsors’
image and of consumers’ loyalty and, progress in the Greenpeace
retailers’ evaluation ranking.
Abstract: In this study, Brillouin Gain Spectrum (BGS) is
experimentally analyzed in the Brillouin Optical Time Domain
Reflectometry (BOTDR) and Brillouin Optical Time Domain
Analyzer (BOTDA). For this purpose, the signal level of the
microwave generator is varied and the effects of BGS are
investigated. In the setups, 20 km conventional single mode fiber is
used to both setups and laser wavelengths are selected around 1550
nm. To achieve best results, it can be used between 5 dBm to 15 dBm
signal level of microwave generator for BOTDA and BOTDR setups.
Abstract: Lightweight and efficient structures have the aim to
enhance the efficiency of the components in various industries.
Toward this end, composites are one of the most widely used
materials because of durability, high strength and modulus, and low
weight. One type of the advanced composites is grid-stiffened
composite (GSC) structures, which have been extensively considered
in aerospace, automotive, and aircraft industries. They are one of the
top candidates for replacing some of the traditional components,
which are used here. Although there are a good number of published
surveys on the design aspects and fabrication of GSC structures, little
systematic work has been reported on their material modification to
improve their properties, to our knowledge. Matrix modification
using nanoparticles is an effective method to enhance the flexural
properties of the fibrous composites. In the present study, a silanecoupling
agent (3-glycidoxypropyltrimethoxysilane/3-GPTS) was
introduced onto the silica (SiO2) nanoparticle surface and its effects
on the three-point flexural response of isogrid E-glass/epoxy
composites were assessed. Based on the Fourier Transform Infrared
Spectrometer (FTIR) spectra, it was inferred that the 3-GPTS
coupling agent was successfully grafted onto the surface of SiO2
nanoparticles after modification. Flexural test revealed an
improvement of 16%, 14%, and 36% in stiffness, maximum load and
energy absorption of the isogrid specimen filled with 3 wt.% 3-
GPTS/SiO2 compared to the neat one. It would be worth mentioning
that in these structures, considerable energy absorption was observed
after the primary failure related to the load peak. In addition, 3-
GPTMS functionalization had a positive effect on the flexural
behavior of the multiscale isogrid composites. In conclusion, this
study suggests that the addition of modified silica nanoparticles is a
promising method to improve the flexural properties of the gridstiffened
fibrous composite structures.
Abstract: Mineral product, waste concrete (fine aggregates),
waste in the optical field, industry, and construction employ separators
to separate solids and classify them according to their size. Various
sorting machines are used in the industrial field such as those operating
under electrical properties, centrifugal force, wind power, vibration,
and magnetic force. Study on separators has been carried out to
contribute to the environmental industry. In this study, we perform
CFD analysis for understanding the basic mechanism of the separation
of waste concrete (fine aggregate) particles from air with a machine
built with a rotor with blades. In CFD, we first performed
two-dimensional particle tracking for various particle sizes for the
model with 1 degree, 1.5 degree, and 2 degree angle between each
blade to verify the boundary conditions and the method of rotating
domain method to be used in 3D. Then we developed 3D numerical
model with ANSYS CFX to calculate the air flow and track the
particles. We judged the capability of particle separation for given size
by counting the number of particles escaping from the domain toward
the exit among 10 particles issued at the inlet. We confirm that
particles experience stagnant behavior near the exit of the rotating
blades where the centrifugal force acting on the particles is in balance
with the air drag force. It was also found that the minimum particle
size that can be separated by the machine with the rotor is determined
by its capability to stay at the outlet of the rotor channels.
Abstract: This paper focuses on the study of DC-to-DC
converters, which are suitable for low-voltage high-power
applications. The output voltages generated by renewable energy
sources such as photovoltaic arrays and fuel cell stacks are
generally low and required to be increased to high voltage levels.
Development of DC-to-DC converters, which provide high step-up
voltage conversion ratios with high efficiencies and low voltage
stresses, is one of the main issues in the development of renewable
energy systems. A procedure for three converters−conventional
DC-to-DC converter, interleaved boost converter, and isolated flyback
based converter, is illustrated for a given set of specifications. The
selection among the converters for the given application is based on
the voltage conversion ratio, efficiency, and voltage stresses.
Abstract: Information technology has been gaining more and
more space whether in industry, commerce or even for personal use,
but the misuse of it brings harm to the environment and human health
as a result. Contribute to the sustainability of the planet is to
compensate the environment, all or part of what withdraws it. The
green computing also came to propose practical for use in IT in an
environmentally correct way in aid of strategic management and
communication. This work focuses on showing how a mobile
application can help businesses reduce costs and reduced
environmental impacts caused by its processes, through a case study
of a public company in Brazil.
Abstract: This paper sets out a behavioral macro-model of a
Merged PiN and Schottky (MPS) diode based on silicon carbide
(SiC). This model holds good for both static and dynamic electrothermal
simulations for industrial applications. Its parameters have
been worked out from datasheets curves by drawing on the
optimization method: Simulated Annealing (SA) for the SiC MPS
diodes made available in the industry. The model also adopts the
Analog Behavioral Model (ABM) of PSPICE in which it has been
implemented. The thermal behavior of the devices was also taken
into consideration by making use of Foster’ canonical network as
figured out from electro-thermal measurement provided by the
manufacturer of the device.
Abstract: Manufacturing process has been considered as one of
the most important activity in business process. It correlates with
productivity and quality of the product so industries could fulfill
customer’s demand. With the increasing demand from customer,
industries must improve their manufacturing ability such as shorten
lead-time and reduce wastes on their process. Lean manufacturing
has been considered as one of the tools to waste elimination in
manufacturing or service industry. Workforce development is one
practice in lean manufacturing that can reduce waste generated from
operator such as waste of unnecessary motion. Anthropometric
approach is proposed to determine the recommended measurement in
operator’s work area. The method will get some dimensions from
Indonesia people that related to piston workstation. The result from
this research can be obtained new design for the work area
considering ergonomic aspect.
Abstract: Polymeric composites are being increasingly used as
repair material for repairing critical infrastructures such as building,
bridge, pressure vessel, piping and pipeline. Technique in repairing
damaged pipes is one of the major concerns of pipeline owners.
Considerable researches have been carried out on the repair of
corroded pipes using composite materials. This article attempts a
short review of the subject matter to provide insight into various
techniques used in repairing corroded pipes, focusing on a wide range
of composite repair systems. These systems including pre-cured
layered, flexible wet lay-up, pre-impregnated, split composite sleeve
and flexible tape systems. Both advantages and limitations of these
repair systems were highlighted. Critical technical aspects have been
discussed through the current standards and practices. Research gaps
and future study scopes in achieving more effective design
philosophy are also presented.
Abstract: This experimental study consists of a characterization
of epoxy grout where an amount of 2% of graphene nanoplatelets
particles were added to commercial epoxy resin to evaluate their
behavior regarding neat epoxy resin. Compressive tests, tensile tests
and flexural tests were conducted to study the effect of graphene
nanoplatelets on neat epoxy resin. By comparing graphene-based and
neat epoxy grout, there is no significant increase of strength due to
weak interface in the graphene nanoplatelets/epoxy composites.
From this experiment, the tension and flexural strength of graphenebased
epoxy grouts is slightly lower than ones of neat epoxy grout.
Nevertheless, the addition of graphene has produced more consistent
results according to a smaller standard deviation of strength.
Furthermore, the graphene has also improved the ductility of the
grout, hence reducing its brittle behaviour. This shows that the
performance of graphene-based grout is reliably predictable and able
to minimise sudden rupture. This is important since repair design of
damaged pipeline is of deterministic nature.
Abstract: Issues relating to the destructive phenomena that can
damage people and goods have returned to the centre of debate in
Italy with the increase in catastrophic episodes in recent years in a
country which is highly vulnerable to hydrological risk.
Environmental factors and geological and geomorphological
territorial characteristics play an important role in determining the
level of vulnerability and the natural tendency to risk. However, a
territory has also been subjected to the requirements of and
transformations of society and this brings other relevant factors. The
reasons for the increase in destructive phenomena are often to be
found in the territorial development models adopted. Stewardship of
the landscape and management of risk are related issues. This study aims to summarize the most relevant elements about
this connection and at the same time to clarify the role of
environmental risk assessment as a tool to aid in the sustainable
management of landscape. Finally, the study reflects on how regional
and urban planners deal with environmental risk and which aspects
should be monitored in order to adopt responsible and useful
interventions.
Abstract: The major environmental risk of soil pollution is the
contamination of groundwater by infiltration of organic and inorganic
pollutants which can cause a serious menace. To prevent this risk and
to protect the groundwater, we proceeded in this study to test the
reliability of a biosolid as barrier to prevent the migration of very
dangerous pollutants as ‘Cadmium’ through the different soil layers. In this study, we tried to highlight the effect of several parameters
such as: turbidity (different cycle of Hydration/Dehydration),
rainfall, effect of initial Cd(II) concentration and the type of soil.
These parameters allow us to find the most effective manner to
integrate this barrier in the soil. From the results obtained, we found a
significant effect of the barrier. Indeed, the recorded passing
quantities are lowest for the highest rainfall; we noted also that the
barrier has a better affinity towards higher concentrations; the most
retained amounts of cadmium has been in the top layer of the two
types of soil tested, while the lowest amounts of cadmium are
recorded in the bottom layers of soils.
Abstract: Hard coatings are widely used in cutting and forming
tool industries. Titanium Nitride (TiN) possesses good hardness,
strength, and corrosion resistance. The coating properties are
influenced by many process parameters. The coatings were deposited
on steel substrate by changing the process parameters such as
substrate temperature, nitrogen flow rate and target power in a D.C
planer magnetron sputtering. The structure of coatings were analysed
using XRD. The hardness of coatings was found using Micro
hardness tester. From the experimental data, a regression model was
developed and the optimum response was determined using Response
Surface Methodology (RSM).
Abstract: Rapid developments in technology in the present age
have made it necessary for communities to follow technological
developments and adapt themselves to these developments. One of
the fields that are most rapidly affected by these developments is
undoubtedly education. Determination of the attitudes of preservice
teachers, who live in an age of technology and get ready to raise
future individuals, is of paramount importance both educationally and
professionally. The purpose of this study was to analyze attitudes of
preservice teachers towards technology and some variables that
predict these attitudes (gender, daily duration of internet use, and the
number of technical devices owned). 329 preservice teachers
attending the education faculty of a large university in central Turkey
participated, on a volunteer basis, in this study, where relational
survey model was used as the research method. Research findings
reveal that preservice teachers’ attitudes towards technology are
positive and at the same time, the attitudes of male preservice
teachers towards technology are more positive than their female
counterparts. As a result of the stepwise multiple regression analysis
where factors predicting preservice teachers’ attitudes towards
technology, it was found that duration of daily internet use was the
strongest predictor of attitudes towards technology.
Abstract: The aim of this work is to study the numerical
implementation of the Hilbert Uniqueness Method for the exact
boundary controllability of Euler-Bernoulli beam equation. This study
may be difficult. This will depend on the problem under consideration
(geometry, control and dimension) and the numerical method used.
Knowledge of the asymptotic behaviour of the control governing the
system at time T may be useful for its calculation. This idea will
be developed in this study. We have characterized as a first step, the
solution by a minimization principle and proposed secondly a method
for its resolution to approximate the control steering the considered
system to rest at time T.
Abstract: Companies face increasing challenges in research due
to higher costs and risks. The intensifying technology complexity and
interdisciplinarity require unique know-how. Therefore, companies
need to decide whether research shall be conducted internally or
externally with partners. On the other hand, research institutes meet
increasing efforts to achieve good financing and to maintain high
research reputation. Therefore, relevant research topics need to be
identified and specialization of competency is necessary. However,
additional competences for solving interdisciplinary research projects
are also often required. Secured financing can be achieved by
bonding industry partners as well as public fundings. The realization
of faster and better research drives companies and research institutes
to cooperate in organized research networks, which are managed by
an administrative organization. For an effective and efficient
cooperation, necessary processes, roles, tools and a set of rules need
to be determined. Goal of this paper is to show the state-of-art
research and to propose a governance framework for organized
research networks.
Abstract: Contemporary metropolitan areas and large cities are
dynamic, rapidly growing and continuously changing. Thus, urban
transformations and mutations are not a new phenomenon, but rather
a continuous process. Basic factors of urban transformation are
related to development of technologies, globalisation, lifestyle, etc.,
which in combination with local factors have generated an extremely
great variety of urban development conditions. This article discusses
the main urbanisation processes in Lithuania during last 50-year
period and social factors affecting urban functional mutations.
Abstract: Zinc borates are used as a multi-functional flame
retardant additive for its high dehydration temperature. In this study,
the method of ultrasonic mixing was used in the synthesis of zinc
borates. The reactants of zinc oxide (ZnO) and boric acid (H3BO3)
were used at the constant reaction parameters of 90°C reaction
temperature and 55 min of reaction time. Several molar ratios of
ZnO:H3BO3 (1:1, 1:2, 1:3, 1:4 and 1:5) were conducted for the
determination of the optimum reaction ratio. Prior to synthesis the
characterization of the synthesized zinc borates were made by X-Ray
Diffraction (XRD) and Fourier Transform Infrared Spectroscopy
(FT-IR). From the results Zinc Oxide Borate Hydrate
[Zn3B6O12.3.5H2O], were synthesized optimum at the molar ratio of
1:3, with a reaction efficiency of 95.2%.