Abstract: Geopolymer concretes are new class of construction
materials that have emerged as an alternative to Ordinary Portland
cement concrete. Considerable researches have been carried out on
material development of geopolymer concrete; however, a few studies
have been reported on the structural use of them. This paper presents
the bond behaviors of reinforcement embedded in fly ash based
geopolymer concrete. The development lengths of reinforcement for
various compressive strengths of concrete, 20, 30 and 40 MPa, and
reinforcement diameters, 10, 16 and 25 mm, are investigated. Total 27
specimens were manufactured and pull-out test according to EN 10080
was applied to measure bond strength and slips between concrete and
reinforcements. The average bond strengths decreased from 23.06MPa
to 17.26 MPa, as the diameters of reinforcements increased from
10mm to 25mm. The compressive strength levels of geopolymer
concrete showed no significant influence on bond strengths in this
study. Also, the bond-slip relations between geopolymer concrete and
reinforcement are derived using non-linear regression analysis for
various experimental conditions.
Abstract: The problematic of gender and socioeconomic status
biased differences in academic motivation patterns is discussed.
Gender identity is understood according to symbolic interactionism
perspective: as a result of reflected appraisals, social comparisons,
self-attributions, and identifications, shaped by social environment
and family context. The effects of socioeconomic status on academic
motivation are conceptualized according to Bourdieu’s habitus
concept, reflecting the role of unconscious and internalized cultural
signals, proper to low and high socioeconomic status family contexts.
Since families differ by various socioeconomic features, the
hypothesis about possible impact of parents’ socioeconomic status on
their children’s academic motivation interfering with gender
socialization effects is held. The survey, aiming to seize gender
differences in academic motivation and self-recorded improvementoriented
efforts as a result of socialization processes operating in the
families of low and high socioeconomic status, was designed. The
results of Lithuanian higher education students’ survey are presented
and discussed.
Abstract: The continuous decline of petroleum and natural gas
reserves and non linear rise of oil price has brought about a
realisation of the need for a change in our perpetual dependence on
the fossil fuel. A day to day increased consumption of crude and
petroleum products has made a considerable impact on our foreign
exchange reserves. Hence, an alternate resource for the conversion of
energy (both liquid and gas) is essential for the substitution of
conventional fuels. Biomass is the alternate solution for the present
scenario. Biomass can be converted into both liquid as well as
gaseous fuels and other feedstocks for the industries.
Abstract: In this paper a new design of a broadband microwave
power limiter is presented and validated into simulation by using
ADS software (Advanced Design System) from Agilent technologies.
The final circuit is built on microstrip lines by using identical Zero
Bias Schottky diodes. The power limiter is designed by Associating 3
stages Schottky diodes. The obtained simulation results permit to
validate this circuit with a threshold input power level of 0 dBm until
a maximum input power of 30 dBm.
Abstract: The ad hoc networks are the future of wireless
technology as everyone wants fast and accurate error free information
so keeping this in mind Bit Error Rate (BER) and power is optimized
in this research paper by using the Genetic Algorithm (GA). The
digital modulation techniques used for this paper are Binary Phase
Shift Keying (BPSK), M-ary Phase Shift Keying (M-ary PSK), and
Quadrature Amplitude Modulation (QAM). This work is
implemented on Wireless Ad Hoc Networks (WLAN). Then it is
analyze which modulation technique is performing well to optimize
the BER and power of WLAN.
Abstract: In recent years, the compression of date (Phoenix
dactylifera L.) fruit powders (DP) to obtain date tablets (DT) has
been suggested as a promising form of valorization of non
commercial valuable date fruit (DF) varieties. To further improve
and characterize DT, the present study aims to investigate the
influence of the DP particle size and compression force on some
physical properties of DT. The results show that independently of
particle size, the hardness (y) of tablets increases with the increase of
the compression force (x) following a logarithmic law (y = a ln (bx)
where a and b are the constants of model). Further, a full factorial
design (FFD) at two levels, applied to investigate the erosion %,
reveals that the effects of time and particle size are the same in
absolute value and they are beyond the effect of the compression.
Regarding the disintegration time, the obtained results also by means
of a FFD show that the effect of the compression force exceeds 4
times that of the DP particle size. As final stage, the color parameters
in the CIELab system of DT immediately after their obtaining are
differently influenced by the size of the initial powder.
Abstract: In this study, we are interested in a species of the
family of Asteraceae (Tagetes erecta). This family is considered as a
source of antimicrobial extracts with strong capacity. The extraction
of the flavonoids is carried out by the method of liquid/liquid with the
use of successive solvents. Afterwards, we evaluated the biological
activity of the flavonoids on five pathogenic bacterial stocks such as
Escherichia coli, Bacillus subtilis, Klebsiella pneumoniae,
Pseudomonas aeruginosa and Staphylococcus aureus and two stocks
of yeasts to knowing Candida albicans) and Saccharomyces
cerevisiae, by employing the method of the aromatogramme starting
from a solid disc. The result of the antimicrobial activity shows an
action and a variable degree of sensitivity according to bacterial
stocks tested. It will be noted that the flavonoids have an inhibiting
effect on E. coli, B. subtilis, K. pneumoniae and S. aureus. But a
resistance with respect to the extract by P. aeruginosa, C. albicans
and S. cerevisiae is to be mentioned.
Abstract: Securing the confidential data transferred via wireless
network remains a challenging problem. It is paramount to ensure
that data are accessible only by the legitimate users rather than by the
attackers. One of the most serious threats to organization is jamming,
which disrupts the communication between any two pairs of nodes.
Therefore, designing an attack-defending scheme without any packet
loss in data transmission is an important challenge. In this paper,
Dependence based Malicious Route Defending DMRD Scheme has
been proposed in multi path routing environment to prevent jamming
attack. The key idea is to defend the malicious route to ensure
perspicuous transmission. This scheme develops a two layered
architecture and it operates in two different steps. In the first step,
possible routes are captured and their agent dependence values are
marked using triple agents. In the second step, the dependence values
are compared by performing comparator filtering to detect malicious
route as well as to identify a reliable route for secured data
transmission. By simulation studies, it is observed that the proposed
scheme significantly identifies malicious route by attaining lower
delay time and route discovery time; it also achieves higher
throughput.
Abstract: This work presents a new planar multiband antenna
based on fractal geometry. This structure is optimized and validated
into simulation by using CST-MW Studio. To feed this antenna we
have used a CPW line which makes it easy to be incorporated with
integrated circuits. The simulation results presents a good matching
input impedance and radiation pattern in the GSM band at 900 MHz
and ISM band at 2.4 GHz. The final structure is a dual band fractal
antenna with 70 x 70 mm² as a total area by using an FR4 substrate.
Abstract: This paper presents a novel design of a microstrip
fractal antenna based on the use of Sierpinski triangle shape, it’s
designed and simulated by using FR4 substrate in the operating
frequency bands (GPS, WiMAX), the design is a fractal antenna with
a modified ground structure. The proposed antenna is simulated and
validated by using CST Microwave Studio Software, the simulated
results presents good performances in term of radiation pattern and
matching input impedance.
Abstract: Logistics distributors face the issue of having to
provide increasing service levels while being forced to reduce costs at
the same time. Same-day delivery, quick order processing and rapidly
growing ranges of articles are only some of the prevailing challenges.
One key aspect of the performance of an intra-logistics system is how
often and in which amplitude congestions and dysfunctions affect the
processing operations. By gaining knowledge of the so called
‘performance availability’ of such a system during the planning stage,
oversizing and wasting can be reduced whereas planning
transparency is increased. State of the art for the determination of this
KPI is simulation studies. However, their structure and therefore their
results may vary unforeseeably. This article proposes a concept for
the establishment of ‘certified’ and hence reliable and comparable
simulation models.
Abstract: Knowledge management is considered as an important
factor in improving health care services. KM facilitates the transfer of
existing knowledge and the development of new knowledge in
hospitals. This paper reviews practices adopted by doctors in Kuwait
for capturing, sharing, and generating knowledge. It also discusses
the perceived impact of KM practices on performance of hospitals.
Based on a survey of 277 doctors, the study found that KM practices
among doctors in the sampled hospitals were not very effective. Little
attention was paid to the main activities that support the transfer of
expertise among doctors in hospitals. However, as predicted by
previous studies, good km practices were perceived by doctors to
have a positive impact on performance of hospitals. It was concluded
that through effective KM practices hospitals could improve the
services they provide. Documentation of best practices and capturing
of lessons learnt for re-use of knowledge could help transform the
hospitals into learning organizations.
Abstract: The paper involves a chain of activities from
synthesis, establishment of the methodology for characterization and
testing of novel protective materials through the pilot production and
application on model supports.
It summarizes the results regarding the development of the pilot
production protocol for newly developed self-cleaning materials. The
optimization of the production parameters was completed in order to
improve the most important functional properties (mineralogy
characteristics, particle size, self-cleaning properties and
photocatalytic activity) of the newly designed nanocomposite
material.
Abstract: This paper designs the four-phase Boost Converter
which overcomes the problem of high input ripple current and output
ripple voltage. Digital control is more convenient for such a topology
on basis of synchronization, phase shift operation, etc. Simulation
results are presented for open-loop and closed-loop for four phase
boost converter. This control scheme is applicable for PFC rectifiers
as well. Thus a comparative analysis based on the obtained results is
performed.
Abstract: The star network is one of the promising
interconnection networks for future high speed parallel computers, it
is expected to be one of the future-generation networks. The star
network is both edge and vertex symmetry, it was shown to have
many gorgeous topological proprieties also it is owns hierarchical
structure framework. Although much of the research work has been
done on this promising network in literature, it still suffers from
having enough algorithms for load balancing problem. In this paper
we try to work on this issue by investigating and proposing an
efficient algorithm for load balancing problem for the star network.
The proposed algorithm is called Star Clustered Dimension Exchange
Method SCDEM to be implemented on the star network. The
proposed algorithm is based on the Clustered Dimension Exchange
Method (CDEM). The SCDEM algorithm is shown to be efficient in
redistributing the load balancing as evenly as possible among all
nodes of different factor networks.
Abstract: The final step to complete the “Analytical Systems
Engineering Process” is the “Allocated Architecture” in which all
Functional Requirements (FRs) of an engineering system must be
allocated into their corresponding Physical Components (PCs). At
this step, any design for developing the system’s allocated
architecture in which no clear pattern of assigning the exclusive
“responsibility” of each PC for fulfilling the allocated FR(s) can be
found is considered a poor design that may cause difficulties in
determining the specific PC(s) which has (have) failed to satisfy a
given FR successfully. The present study utilizes the Axiomatic
Design method principles to mathematically address this problem and
establishes an “Axiomatic Model” as a solution for reaching good
alternatives for developing the allocated architecture. This study
proposes a “loss Function”, as a quantitative criterion to monetarily
compare non-ideal designs for developing the allocated architecture
and choose the one which imposes relatively lower cost to the
system’s stakeholders. For the case-study, we use the existing design
of U. S. electricity marketing subsystem, based on data provided by
the U.S. Energy Information Administration (EIA). The result for
2012 shows the symptoms of a poor design and ineffectiveness due to
coupling among the FRs of this subsystem.
Abstract: Machining parameters are very important in
determining the surface quality of any material. In the past decade,
some new engineering materials were developed for the
manufacturing industry which created a need to conduct an
investigation on the impact of the said parameters on their surface
roughness. Polyurethane (PU) block is widely used in the automotive
industry to manufacture parts such as checking fixtures that are used
to verify the dimensional accuracy of automotive parts. In this paper,
the design of experiment (DOE) was used to investigate on the effect
of the milling parameters on the PU block. Furthermore, an analysis
of the machined surface chemical composition was done using
scanning electron microscope (SEM). It was found that the surface
roughness of the PU block is severely affected when PU undergoes a
flood machining process instead of a dry condition. In addition the
stepover and the silicon content were found to be the most significant
parameters that influence the surface quality of the PU block.
Abstract: The computational fluid dynamics (CFD) study of
stirred tank with the air-water interface are carried out in the presence
of different types of the impeller and with or without baffles. A
multiple reference frame (MRF) approach with the volume of fluid
(VOF) method is used to capture the air-water interface. The RANS
(Reynolds Averaged Navier-Stokes) equations with k-ε turbulence
model are solved to predict the flow behavior of water and air phase
which are treated as a different phases. The predicted results have
shown that the VOF method is able to capture the interface in the
unbaffled tank. While, the VOF method is showing an unfeasible
results in the baffled tank with high rotational impeller speed. For
continuous stirred tank, the air-water interface is disturbed by the
inflow and the level of water is also increased with time.
Abstract: Safety is one of the most important considerations
when buying a new car. While active safety aims at avoiding
accidents, passive safety systems such as airbags and seat belts
protect the occupant in case of an accident. In addition to legal
regulations, organizations like Euro NCAP provide consumers with
an independent assessment of the safety performance of cars and
drive the development of safety systems in automobile industry.
Those ratings are mainly based on injury assessment reference values
derived from physical parameters measured in dummies during a car
crash test.
The components and sub-systems of a safety system are designed
to achieve the required restraint performance. Sled tests and other
types of tests are then carried out by car makers and their suppliers
to confirm the protection level of the safety system. A Knowledge
Discovery in Databases (KDD) process is proposed in order to
minimize the number of tests. The KDD process is based on the
data emerging from sled tests according to Euro NCAP specifications.
About 30 parameters of the passive safety systems from different data
sources (crash data, dummy protocol) are first analysed together with
experts opinions. A procedure is proposed to manage missing data
and validated on real data sets. Finally, a procedure is developed to
estimate a set of rough initial parameters of the passive system before
testing aiming at reducing the number of tests.
Abstract: Bamboo is extensively used in construction industry.
Low durability of bamboo due to fungus infestation and termites
attack under storage puts certain constrains for it usage as modern
structural material. Looking at many chemical formulations for
bamboo treatment leading to severe harmful environment effects,
research on eco-friendly preservatives for bamboo treatment has been
initiated world-over. In the present studies, eco-friendly preservative
for bamboo treatment has been developed. To validate its application
for structural purposes, investigation of effect of treatment on
compressive strength has been investigated. Neemoil (25%)
integrated with copper naphthenate (0.3%) on dilution with kerosene
oil impregnated into bamboo culm at 2 bar pressure, has shown
weight loss of only 3.15% in soil block analysis method. The results
from compressive strength analysis using HEICO Automatic
Compression Testing Machine reveal that preservative treatment has
not altered the structural properties of bamboo culms. Compressive
strength of control (11.72 N/mm2) and above treated samples (11.71
N/mm2) was found to be comparable.