Abstract: Two types of glass fibers having different lengths
(1/16" and 1/32") were added into rigid PVC foams to enhance the
dimensional stability of extruded rigid Polyvinyl Chloride (PVC)
foam at different concentrations (0-20 phr) using a single screw
profile extruder. PVC foam-glass fiber composites (PVC-GF) were
characterized for their dimensional stability, structural, thermal, and
mechanical properties. Experimental results show that the
dimensional stability, heat resistance, and storage modulus were
enhanced without compromising the tensile and flexural strengths of
the composites. Overall, foam composites which were prepared with
longer glass fibers exhibit better mechanical and thermal properties
than those prepared with shorter glass fibers due to higher
interlocking between the fibers and the foam cells, which result in
better load distribution in the matrix.
Abstract: In this study, microcrystalline cellulose (MCC) was
extracted from oil palm empty fruit bunch (EFB) cellulose which was
earlier isolated from oil palm EFB fibre. In order to isolate the
cellulose, the chlorination method was carried out. Then, the MCC
was prepared by simultaneous ultrasonic and alkali treatment from
the isolated α-cellulose. Based on mass balance calculation, the yields
for MCC obtained from EFB was 44%. For fiber characterization, it
is observed that the chemical composition of the hemicellulose and
lignin for all samples decreased while composition for cellulose
increased. The structural property of the MCC was studied by X-ray
diffraction (XRD) method and the result shows that the MCC
produced is a cellulose-I polymorph, with 73% crystallinity.
Abstract: Among modern airflow measurement methods,
Particle Image Velocimetry (PIV) and Particle Tracking Velocimetry
(PTV), as visualized and non-instructive measurement techniques, are
playing more important role. This paper conducts a comparative
experimental study for airflow measurement employing both
techniques with the same condition. Velocity vector fields, velocity
contour fields, voticity profiles and turbulence profiles are selected as
the comparison indexes. The results show that the performance of both
PIV and PTV techniques for airflow measurement is satisfied, but
some differences between the both techniques are existed, it suggests
that selecting the measurement technique should be based on a
comprehensive consideration.
Abstract: Due to the importance of ports to trade and economic
development of the regions in which they are inserted, in recent
decades the number of studies devoted to this subject has increased.
Part of these studies considers the ports as business agglomerations
and focuses on port governance. This is an important approach since
the port performance is the result of activities performed by actors
belonging to the port-logistics chain, which need to be properly
coordinated. This coordination takes place through a port governance
model. Given this context, this study aims to analyze the governance
model of the port of Santos from the perspective of port customers.
To do this, a closed-ended questionnaire based on a conceptual model
that considers the key dimensions associated with port governance
was applied to the international freight forwarders that operate in the
port. The results show the applicability of the considered model and
highlight improvement opportunities to be implemented at the port of
Santos.
Abstract: The main purpose of this work was verify the
influence of the accelerated carbonation in the physical and
mechanical properties of the hybrid composites, reinforced with
micro and nanofibers and composites with microfibers. The
composites were produced by the slurry vacuum dewatering method,
followed by pressing. It was produced using two formulations: 8% of
eucalyptus pulp + 1% of the nanofibrillated cellulose and 9% of
eucalyptus pulp, both were subjected to accelerated carbonation. The
results showed that the accelerated carbonation contributed to
improve the physical and mechanical properties of the hybrid
composites and of the composites reinforced with microfibers
(eucalyptus pulp).
Abstract: Monocopter is a single-wing rotary flying vehicle
which has the capability of hovering. This flying vehicle includes two
dynamic parts in which more efficiency can be expected rather than
other Micro UAVs due to the extended area of wing compared to its
fuselage. Low cost and simple mechanism in comparison to other
vehicles such as helicopter are the most important specifications of
this flying vehicle.
In the previous paper we discussed the introduction of the final
system but in this paper, the experimental design process of
Monocopter and its control algorithm has been investigated in
general. Also the editorial bugs in the previous article have been
corrected and some translational ambiguities have been resolved.
Initially by constructing several prototypes and carrying out many
flight tests the main design parameters of this air vehicle were
obtained by experimental measurements. Eventually the required
main monocopter for this project was constructed. After construction
of the monocopter in order to design, implementation and testing of
control algorithms first a simple optic system used for determining
the heading angle. After doing numerous tests on Test Stand, the
control algorithm designed and timing of applying control inputs
adjusted. Then other control parameters of system were tuned in
flight tests. Eventually the final control system designed and
implemented using the AHRS sensor and the final operational tests
performed successfully.
Abstract: Aerated concrete is a load bearing construction
material, which has high heat insulation parameters. Walls can be
erected from aerated concrete masonry constructions and in perfect
circumstances additional heat insulation is not required. The most
common problem in aerated concrete heat insulation properties is the
humidity distribution throughout the cross section of the masonry
elements as well as proper and conducted drying process of the
aerated concrete construction because only dry aerated concrete
masonry constructions can reach high heat insulation parameters.
In order to monitor drying process of the masonry and detect
humidity distribution throughout the cross section of aerated concrete
masonry construction application of electrical impedance
spectrometry is applied. Further test results and methodology of this
non-destructive testing method is described in this paper.
Abstract: Using cold EGR method with variable venturi and
turbocharger has a very significant effect on reduction of NOX and
grime simultaneously. EGR cooler is one of the most important parts
in the cold EGR circuit. In this paper optimum design of cooler for
working in different percentages of EGR and for determining
optimum temperature of exhausted gases, growth of efficiency,
reduction of weight, dimension, expenditures, sediment and also
optimum performance by using gasoil which has significant amounts
of brimstone are investigated and optimized.
Abstract: The extermination and proper disposal of
pharmaceutical wastes from expired and unused medications remains
a disputable issue due to their specific nature and characteristics.
Even though the hazards from these wastes are already well known in
terms of environment and human health, people still treat them as
usual wastes. At a national level, in many countries the management
of pharmaceutical and medical wastes has been one of the main
objectives in order to protect people’s health and the environment.
Even though many legal regulations exist in this respect, there has not
been a single law that would clearly explain the procedures of
returning medicines, ways of selection, treatment and extermination
of pharmaceutical wastes. This paper aims at analyzing the practices
of pharmaceutical waste management and treatment in some
European countries as well as a review of the legislation and official
guidelines in managing these kinds of wastes and protecting the
environment and human health. A suitable treatment and
management of expired medications and other similar wastes would
be in the interest of public health in the first place, as well as in the
interest of healthcare institutions and other bodies engaged in
environment protection.
Abstract: Search engine plays an important role in internet, to
retrieve the relevant documents among the huge number of web
pages. However, it retrieves more number of documents, which are
all relevant to your search topics. To retrieve the most meaningful
documents related to search topics, ranking algorithm is used in
information retrieval technique. One of the issues in data miming is
ranking the retrieved document. In information retrieval the ranking
is one of the practical problems. This paper includes various Page
Ranking algorithms, page segmentation algorithms and compares
those algorithms used for Information Retrieval. Diverse Page Rank
based algorithms like Page Rank (PR), Weighted Page Rank (WPR),
Weight Page Content Rank (WPCR), Hyperlink Induced Topic
Selection (HITS), Distance Rank, Eigen Rumor, Distance Rank Time
Rank, Tag Rank, Relational Based Page Rank and Query Dependent
Ranking algorithms are discussed and compared.
Abstract: This paper proposes a new technique to design a
fixed-structure robust loop shaping controller for the pneumatic
servosystem. In this paper, a new method based on a particle swarm
optimization (PSO) algorithm for tuning the weighting function
parameters to design an H∞ controller is presented. The PSO
algorithm is used to minimize the infinity norm of the transfer
function of the nominal closed loop system to obtain the optimal
parameters of the weighting functions. The optimal stability margin is
used as an objective in PSO for selecting the optimal weighting
parameters; it is shown that the proposed method can simplify the
design procedure of H∞ control to obtain optimal robust controller for
pneumatic servosystem. In addition, the order of the proposed
controller is much lower than that of the conventional robust loop
shaping controller, making it easy to implement in practical works.
Also two-degree-of-freedom (2DOF) control design procedure is
proposed to improve tracking performance in the face of noise and
disturbance. Result of simulations demonstrates the advantages of the
proposed controller in terms of simple structure and robustness
against plant perturbations and disturbances.
Abstract: This paper proposes a backward/forward sweep
method to analyze the power flow in radial distribution systems. The
distribution system has radial structure and high R/X ratios. So the
newton-raphson and fast decoupled methods are failed with
distribution system. The proposed method presents a load flow study
using backward/forward sweep method, which is one of the most
effective methods for the load-flow analysis of the radial distribution
system. By using this method, power losses for each bus branch and
voltage magnitudes for each bus node are determined. This method
has been tested on IEEE 33-bus radial distribution system and
effective results are obtained using MATLAB.
Abstract: Corrosion inhibitors are widely used in concrete
industry to reduce the corrosion rate of steel rebar which is present in
contact with aggressive environments. The present work aims to
using Zamzam water from well located within the Masjid al-Haram
in Mecca, Saudi Arabia 20 m (66 ft) east of the Kaaba, the holiest
place in Islam as corrosion inhibitor for steel in rain water and
simulated acid rain. The effect of Zamzam water was investigated by
electrochemical impedance spectroscopy (EIS) and Potentiodynamic
polarization techniques in Department of Civil Engineering - IUT
Saint-Nazaire, Nantes University, France. Zamzam water is
considered to be one of the most important steel corrosion inhibitor
which is frequently used in different industrial applications. Results
showed that zamzam water gave a very good inhibition for steel
corrosion in rain water and simulated acid rain.
Abstract: An algorithm is a well-defined procedure that takes
some input in the form of some values, processes them and gives the
desired output. It forms the basis of many other algorithms such as
searching, pattern matching, digital filters etc., and other applications
have been found in database systems, data statistics and processing,
data communications and pattern matching. This paper introduces
algorithmic “Enhanced Bidirectional Selection” sort which is
bidirectional, stable. It is said to be bidirectional as it selects two
values smallest from the front and largest from the rear and assigns
them to their appropriate locations thus reducing the number of
passes by half the total number of elements as compared to selection
sort.
Abstract: In this paper, the formulation of a new group explicit
method with a fourth order accuracy is described in solving the two
dimensional Helmholtz equation. The formulation is based on the
nine-point fourth order compact finite difference approximation
formula. The complexity analysis of the developed scheme is also
presented. Several numerical experiments were conducted to test the
feasibility of the developed scheme. Comparisons with other existing
schemes will be reported and discussed. Preliminary results indicate
that this method is a viable alternative high accuracy solver to the
Helmholtz equation.
Abstract: This paper reviews the internal use of blogs and their
potential effectiveness as organisational learning tools. Since the
emergence of the concept of ‘Enterprise 2.0’ there remains a lack of
empirical evidence associated with how organisations are applying
social media tools and whether they are effective towards supporting
organisational learning. Surprisingly, blogs, one of the more
traditional social media tools, still remains under-researched in the
context of ‘Enterprise 2.0’ and organisational learning. The aim of
this paper is to identify the theoretical linkage between blogs and
organisational learning in addition to reviewing prior research on
organisational blogging exploring why this area remains underresearched.
Through a literature review, one of the principal findings
of this paper is that organisational blogs have a mutual compatibility
with the interpretivist aspect of organisational learning. This paper
further advocates that further empirical work in this subject area is
required to substantiate this theoretical assumption.
Abstract: The electric power supplied by a photovoltaic power
generation systems depends on the solar irradiation and temperature.
The PV system can supply the maximum power to the load at a
particular operating point which is generally called as maximum
power point (MPP), at which the entire PV system operates with
maximum efficiency and produces its maximum power. Hence, a
Maximum power point tracking (MPPT) methods are used to
maximize the PV array output power by tracking continuously the
maximum power point. The proposed MPPT controller is designed
for 10kW solar PV system installed at Cape Institute of Technology.
This paper presents the fuzzy logic based MPPT algorithm. However,
instead of one type of membership function, different structures of
fuzzy membership functions are used in the FLC design. The
proposed controller is combined with the system and the results are
obtained for each membership functions in Matlab/Simulink
environment. Simulation results are decided that which membership
function is more suitable for this system.
Abstract: E-business technologies, whereby business
transactions are conducted remotely using the Internet, present
unique opportunities and challenges for business. E-business
technologies are applicable to a wide range of organizations and
small and medium-sized enterprises (SMEs) are no exception. There
is an established body of literature about e-business, looking at
definitions, concepts, benefits and challenges. In general, however,
the research focus has been on larger organizations, not SMEs. In an
attempt to redress the balance of research, this paper looks at ebusiness
technologies specifically from a small business perspective.
It seeks to identify the possible barriers that SMEs might face when
considering adoption of the e-business concept and practice as part of
their business process change initiatives and implementation. To
facilitate analysis of these barriers a conceptual framework has been
developed which outlines the key conceptual and practical challenges
of e-business implementation in SMEs. This is developed following a
literature survey comprised of three categories: characteristics of
SMEs, issues of IS/IT use in SMEs and general e-business adoption
and implementation issues. The framework is then empirically
assessed against 7 SMEs who have yet to implement e-business or
whose e-business efforts have been unsatisfactory. Conclusions from
the case studies can be used to verify the framework, and set
parameters for further larger scale empirical investigation.
Abstract: Enterprise Architecture (EA) is a strategy that is
employed by enterprises in order to align their business and
Information Technology (IT). EA is managed, developed, and
maintained through Enterprise Architecture Implementation
Methodology (EAIM). Effectiveness of EA implementation is the
degree in which EA helps to achieve the collective goals of the
organization. This paper analyzes the results of a survey that aims to
explore the factors that affect the effectiveness of EAIM and
specifically the relationship between factors and effectiveness of the
output and functionality of EA project. The exploratory factor
analysis highlights a specific set of five factors: alignment,
adaptiveness, support, binding, and innovation. The regression
analysis shows that there is a statistically significant and positive
relationship between each of the five factors and the effectiveness of
EAIM. Consistent with theory and practice, the most prominent
factor for developing an effective EAIM is innovation. The findings
contribute to the measuring the effectiveness of EA implementation
project by providing an indication of the measurement
implementation approaches which is used by the Enterprise
Architects, and developing an effective EAIM.
Abstract: Images are important source of information used as
evidence during any investigation process. Their clarity and accuracy
is essential and of the utmost importance for any investigation.
Images are vulnerable to losing blocks and having noise added to
them either after alteration or when the image was taken initially,
therefore, having a high performance image processing system and it
is implementation is very important in a forensic point of view. This
paper focuses on improving the quality of the forensic images.
For different reasons packets that store data can be affected,
harmed or even lost because of noise. For example, sending the
image through a wireless channel can cause loss of bits. These types
of errors might give difficulties generally for the visual display
quality of the forensic images.
Two of the images problems: noise and losing blocks are covered.
However, information which gets transmitted through any way of
communication may suffer alteration from its original state or even
lose important data due to the channel noise. Therefore, a developed
system is introduced to improve the quality and clarity of the forensic
images.