Abstract: The change in orbit evolution between collocated
satellites (X, Y) inside +/-0.09° E/W and +/- 0.07° N/S cluster, after
one of these satellites is placed in an inclined orbit (satellite X) and
the effect of this change in the collocation safety inside the cluster
window has been studied and evaluated. Several collocation scenarios had been studied in order to adjust
the location of both satellites inside their cluster to maximize the
separation between them and safe the mission.
Abstract: In the present study, feasibility of the selective surface
hydrophilization of polyvinyl chloride (PVC) by microwave treatment
was evaluated to facilitate the separation from automotive shredder
residue (ASR), by the froth flotation. The combination of 60 sec
microwave treatment with PAC, a sharp and significant decrease about
16.5° contact angle of PVC was observed in ASR plastic compared
with other plastics. The microwave treatment with the addition of PAC
resulted in a synergetic effect for the froth flotation, which may be a
result of the 90% selective separation of PVC from ASR plastics, with
82% purity. While, simple mixing with a nanometallic Ca/CaO/PO4
dispersion mixture immobilized 95-100% of heavy metals in ASR
soil/residues. The quantity of heavy metals leached from thermal
residues after treatment by nanometallic Ca/CaO/PO4 was lower than
the Korean standard regulatory limit for hazardous waste landfills.
Microwave treatment can be a simple and effective method for PVC
separation from ASR plastics.
Abstract: In this paper, according to the classical algorithm
LSQR for solving the least-squares problem, an iterative method is
proposed for least-squares solution of constrained matrix equation. By
using the Kronecker product, the matrix-form LSQR is presented to
obtain the like-minimum norm and minimum norm solutions in a
constrained matrix set for the symmetric arrowhead matrices. Finally,
numerical examples are also given to investigate the performance.
Abstract: In this paper, von Mises and Drucker-Prager yield criteria, as typical ones that consider the effect of intermediate principal stress σ2, have been selected and employed for investigating the influence of σ2 on the solution of a typical stability problem. The bearing capacity factors have been calculated under plane strain condition (strip footing) and axisymmetric condition (circular footing) using the method of stress characteristics together with the criteria mentioned. Different levels of σ2 relative to the other two principal stresses have been considered. While a higher σ2 entry in yield criterion gives a higher bearing capacity; its entry in equilibrium equations (axisymmetric) causes substantial reduction.
Abstract: Since the advances in digital imaging technologies have led to
development of high quality digital devices, there are a lot of illegal copies
of copyrighted video content on the Internet. Also, unauthorized editing is
occurred frequently. Thus, we propose an editing prevention technique for
high-quality (HQ) video that can prevent these illegally edited copies from
spreading out. The proposed technique is applied spatial and temporal gradient
methods to improve the fidelity and detection performance. Also, the scheme
duplicates the embedding signal temporally to alleviate the signal reduction
caused by geometric and signal-processing distortions. Experimental results
show that the proposed scheme achieves better performance than previously
proposed schemes and it has high fidelity. The proposed scheme can be used
in unauthorized access prevention method of visual communication or traitor
tracking applications which need fast detection process to prevent illegally
edited video content from spreading out.
Abstract: In the past years electric mobility became part of a
public discussion. The trend to fully electrified vehicles instead of
vehicles fueled with fossil energy has notably gained momentum.
Today nearly every big car manufacturer produces and sells fully
electrified vehicles, but electrified vehicles are still not as competitive
as conventional powered vehicles. As the traction battery states the
largest cost driver, lowering its price is a crucial objective. In
addition to improvements in product and production processes a nonnegligible,
but widely underestimated cost driver of production can
be found in logistics, since the production technology is not
continuous yet and neither are the logistics systems. This paper presents an approach to evaluate cost factors on
different designs of load carrier systems. Due to numerous
interdependencies, the combination of costs factors for a particular
scenario is not transparent. This is effecting actions for cost reduction
negatively, but still cost reduction is one of the major goals for
simultaneous engineering processes. Therefore a concurrent and
phase appropriate cost valuation method is necessary to serve cost
transparency. In this paper the four phases of this cost valuation
method are defined and explained, which based upon a new approach
integrating the logistics development process in to the integrated
product and process development.
Abstract: This study evaluated the acute toxicity and tissue
distribution of intravenously administered gold nanoparticles
(AuNPs) in male rabbits. Rabbits were exposed to single dose of
AuNPs (300 μg/ kg). Toxic effects were assessed via general
behavior, hematological parameters, serum biochemical parameters,
and histopathological examination of various rabbits’ organs.
Inductively coupled plasma–mass spectrometry (ICP-MS) was used
to determine gold concentrations in tissue samples collected at
predetermined time intervals. After one week, AuNPs exerted no
obvious acute toxicity in rabbits. However, inflammatory reactions
were observed in liver, lungs and kidneys accompanied with mild
absolute neutrophilia and significant monocytosis. The highest gold
levels were found in the spleen and liver followed by lungs, and
kidneys. These results indicated that AuNPs could be distributed
extensively to various tissues in the body, but primarily in the spleen
and liver.
Abstract: The end panels of a large rectangular industrial duct,
which experience significant internal pressures, also experience
considerable transverse shear due to transfer of gravity loads to the
supports. The current design practice of such thin plate panels for
shear load is based on methods used for the design of plate girder
webs. The structural arrangements, the loadings and the resulting
behavior associated with the industrial duct end panels are, however,
significantly different from those of the web of a plate girder. The
large aspect ratio of the end panels gives rise to multiple bands of
tension fields, whereas the plate girder web design is based on one
tension field. In addition to shear, the industrial end panels are
subjected to internal pressure which in turn produces significant
membrane action. This paper reports a study which was undertaken
to review the current industrial analysis and design methods and to
propose a comprehensive method of designing industrial duct end
panels for shear resistance. In this investigation, a nonlinear finite element model was
developed to simulate the behavior of industrial duct end panel, along
with the associated edge stiffeners, subjected to transverse shear and
internal pressures. The model considered the geometric imperfections
and constitutive relations for steels. Six scale independent
dimensionless parameters that govern the behavior of such end panel
were identified and were then used in a parametric study. It was
concluded that the plate slenderness dominates the shear strength of
stockier end panels, and whereas, both the plate slenderness and the
aspect ratio influence the shear strength of slender end panels. Based
on these studies, this paper proposes design aids for estimating the
shear strength of rectangular duct end panels.
Abstract: In this work, our goal is to optimize the nitriding treatment at a low-temperature of the steel 32CrMoV13 using gas mixtures of ammonia, nitrogen and hydrogen to improve the mechanical properties of the surface (good wear resistance, friction and corrosion), and of the diffusion layer of the nitrogen (good resistance to fatigue and good tenacity with heart). By limiting our work to the pure iron and to the alloys iron-chromium and iron-chromium-carbon, we have studied the various parameters which manage the nitriding: flow rate and composition of the gaseous phase, the interaction chromium-nitrogen and chromium-carbon by the help of experiments of nitriding realized in the laboratory by thermogravimetry. The acquired knowledge has been applied by the mastery of the growth of the γ' combination layer on the α diffusion layer in the case of the industrial steel 32CrMoV13.
Abstract: Thermoacoustic refrigerator is a cooling device which
uses the acoustic waves to produce the cooling effect. The aim of this
paper is to explore the experimental and numerical feasibility of a
standing-wave thermoacoustic refrigerator. The effects of the stack
length, position of stack and operating frequency on the cooling
performance are carried out. The circular pore stacks are tested under
the atmospheric pressure. A low-cost loudspeaker is used as an
acoustic driver. The results show that the location of stack installed in
resonator tube has a greater effect on the cooling performance, than
the stack length and operating frequency, respectively. The
temperature difference across the ends of stack can be generated up
to 13.7°C, and the temperature of cold-end is dropped down by 5.3°C
from the ambient temperature.
Abstract: The purpose of the study is to investigate the level of
intrinsic motivation of trainers after attending a Continuous
Professional Development Course (CPD) organized by Institute of
Teacher Training Malaysia titled, “Transformation of Teaching and
Learning the Fun Way”. This study employed a survey whereby 96
teacher trainers were given Situational Intrinsic Motivational Scale
(SIMS) Instruments. Confirmatory factor analysis was carried out to
get the validity of this instrument in local setting. Data were analyzed
with SPSS for descriptive statistic. Semi- structured interviews were
also administrated to collect qualitative data on participants’
experiences after participating in the two-day fun-filled program. The
findings showed that the participants’ level of intrinsic motivation
showed higher mean than the amotivation. The results revealed that
the intrinsic motivation mean is 19.0 followed by Identified
regulation with a mean of 17.4, external regulation 9.7 and
amotivation 6.9. The interview data also revealed that the participants
were motivated after attending this training program. It can be
concluded that this program, which was organized by Institute of
Teacher Training Malaysia, was able to enhance participants’ level of
motivation. Self-Determination Theory (SDT) as a multidimensional
approach to motivation was utilized. Therefore, teacher trainers may
have more success using the “The fun way approach” in conducting
training program in future.
Abstract: The power electronic components within Electric Vehicles (EV) need to operate in several important modes. Some modes directly influence safety, while others influence vehicle performance. Given the variety of functions and operational modes required of the power electronics, it needs to meet efficiency requirements to minimize power losses. Another challenge in the control and construction of such systems is the ability to support bidirectional power flow. This paper considers the construction, operation, and feasibility of available converters for electric vehicles with feasible configurations of electrical buses and loads. This paper describes logic and control signals for the converters for different operations conditions based on the efficiency and energy usage bases.
Abstract: This research was made during the 2015 growing
periods in the trial filed of "Research Station for Department of Field
Crops, Agricultural Faculty, Selcuk University" according to
“Randomized Blocks Design” with 3 replications. Research material
was the following pea lines; PS16, PS18, PS21, PS23, PS24, PS25,
PS36, PS47, PS49, PS51, PS54, PS58, PS67, PS69, PS71, PS73,
PS83, PS84, PS87 and PSKY and three cultivars and other 2
commercial varieties named as Bolero, Rondo and Ultrello. Some
agronomical characteristics such as plant height (cm) number of pod
per plant number of seed per pod number of seed per plant 100 seed
weight (g) and seed yield (kg ha-1) were determined. The highest seed
yield was obtained 2727.0 kg ha-1 in the PS71 line and the lowest
value was obtained 1238.0 kg ha-1 in the commercial variety of
Bolero. Results of the research implicated that the new developed
lines were superior compared with the control (commercial) varieties
by means of most of the characteristics. Nevertheless, similar
researches should be continued in different locations and years.
Abstract: In Algeria, the conditioning units of dates, generate
significant quantities of waste arising from sorting deviations. This
biomass, until then considered as a waste with high impact on the
environment can be transformed into high value added product. It is
possible to develop common dates of low commercial value, and put
on the local and international market a new generation of products
with high added values such as bio ethanol. Besides its use in
chemical synthesis, bio ethanol can be blended with gasoline to
produce a clean fuel while improving the octane.
Abstract: The research explored the effect of morphemic analysis
awareness on ESL secondary school students’ vocabulary acquisition.
The quasi-experimental study was conducted with 100 ESL
secondary school students in two experimental groups (inflectional
and derivational) and one control group. The students’ vocabulary
acquisition was assessed through two measures: Morph-Analysis Test
and Morph-Vocabulary Test in the pretest and posttest before and
after an intervention programme. Results of ANCOVA revealed that
both the experimental groups achieved a significant score in Morph-
Analysis Test and Vocabulary-Morphemic Test. However, the
inflectional group obtained a fairly higher score than the derivational
group. Thus, the findings of the research are discussed in two main
areas. First, individual instructions of two types of morphemic
awareness have contributed significant results on inflectional and
derivational awareness among the ESL secondary school students.
Nevertheless, derivational morphology achieved a significant but
relatively smaller amount of effect on secondary school students’
morphological awareness compared to inflectional morphology in
this research. Second finding showed that the awareness of
inflectional and derivational morphology was found significantly
related to vocabulary achievement of ESL secondary school students.
Nevertheless, inflectional morphemic awareness had higher
significant effect on ESL secondary school students’ vocabulary
acquisition. Despite these findings, the study implies that morphemic
analysis awareness can serve as an alternative strategy for ESL
secondary school students in acquiring English vocabulary.
Abstract: The Com-Poisson (CMP) model is one of the most
popular discrete generalized linear models (GLMS) that handles
both equi-, over- and under-dispersed data. In longitudinal context,
an integer-valued autoregressive (INAR(1)) process that incorporates
covariate specification has been developed to model longitudinal
CMP counts. However, the joint likelihood CMP function is
difficult to specify and thus restricts the likelihood-based estimating
methodology. The joint generalized quasi-likelihood approach
(GQL-I) was instead considered but is rather computationally
intensive and may not even estimate the regression effects due
to a complex and frequently ill-conditioned covariance structure.
This paper proposes a new GQL approach for estimating the
regression parameters (GQL-III) that is based on a single score vector
representation. The performance of GQL-III is compared with GQL-I
and separate marginal GQLs (GQL-II) through some simulation
experiments and is proved to yield equally efficient estimates as
GQL-I and is far more computationally stable.
Abstract: The 1:1 cocrystal of 2-amino-4-chloro-6-
methylpyrimidine (2A4C6MP) with 4-methylbenzoic acid (4MBA)
(I) has been prepared by slow evaporation method in methanol,
which was crystallized in monoclinic C2/c space group, Z = 8, and a
= 28.431 (2) Å, b = 7.3098 (5) Å, c = 14.2622 (10) Å and β =
109.618 (3)°. The presence of unionized –COOH functional group in
cocrystal I was identified both by spectral methods (1H and 13C
NMR, FTIR) and X-ray diffraction structural analysis. The
2A4C6MP molecule interact with the carboxylic group of the
respective 4MBA molecule through N—H⋯O and O—H⋯N
hydrogen bonds, forming a cyclic hydrogen–bonded motif R2
2(8).
The crystal structure was stabilized by Npyrimidine—H⋯O=C and
C=O—H⋯Npyrimidine types hydrogen bonding interactions.
Theoretical investigations have been computed by HF and density
function (B3LYP) method with 6–311+G (d,p)basis set. The
vibrational frequencies together with 1H and 13C NMR chemical
shifts have been calculated on the fully optimized geometry of
cocrystal I. Theoretical calculations are in good agreement with the
experimental results. Solvent–free formation of this cocrystal I is
confirmed by powder X-ray diffraction analysis.
Abstract: In the vicinity of red sea about 15 fungi species were
isolated from oil contaminated sites. On the basis of aptitude to
degrade the crude oil and DCPIP assay, two fungal isolates were
selected amongst 15 oil degrading strains. Analysis of ITS-1, ITS-2
and amplicon pyrosequencing studies of fungal diversity revealed
that these strains belong to Penicillium and Aspergillus species. Two
strains that proved to be the most efficient in degrading crude oil was
Aspergillus niger (54%) and Penicillium commune (48%) Subsequent
to two weeks of cultivation in BHS medium the degradation rate
were recorded by using spectrophotometer and GC-MS. Hence, it is
cleared that these fungal strains has capability of degradation and can
be utilize for cleaning the Saudi Arabian environment.
Abstract: Lateral Geniculate Nucleus (LGN) is the relay center
in the visual pathway as it receives most of the input information
from retinal ganglion cells (RGC) and sends to visual cortex. Low
threshold calcium currents (IT) at the membrane are the unique
indicator to characterize this firing functionality of the LGN neurons
gained by the RGC input. According to the LGN functional
requirements such as functional mapping of RGC to LGN, the
morphologies of the LGN neurons were developed. During the
neurological disorders like glaucoma, the mapping between RGC and
LGN is disconnected and hence stimulating LGN electrically using
deep brain electrodes can restore the functionalities of LGN. A
computational model was developed for simulating the LGN neurons
with three predominant morphologies each representing different
functional mapping of RGC to LGN. The firings of action potentials
at LGN neuron due to IT were characterized by varying the
stimulation parameters, morphological parameters and orientation. A
wide range of stimulation parameters (stimulus amplitude, duration
and frequency) represents the various strengths of the electrical
stimulation with different morphological parameters (soma size,
dendrites size and structure). The orientation (0-1800) of LGN
neuron with respect to the stimulating electrode represents the angle
at which the extracellular deep brain stimulation towards LGN
neuron is performed. A reduced dendrite structure was used in the
model using Bush–Sejnowski algorithm to decrease the
computational time while conserving its input resistance and total
surface area. The major finding is that an input potential of 0.4 V is
required to produce the action potential in the LGN neuron which is
placed at 100 μm distance from the electrode. From this study, it can
be concluded that the neuroprostheses under design would need to
consider the capability of inducing at least 0.4V to produce action
potentials in LGN.
Abstract: The current statuses of lifetime test of LaB6 hollow
cathode at the Lanzhou Institute of Physics (LIP), China, was
described. 5A LaB6 hollow cathode was design for LIPS-200 40mN
Xenon ion thruster, and it could be used for LHT-100 80 mN Hall
thruster, too. Life test of the discharge and neutralizer modes of LHC-5
hollow cathode were stared in October 2011, and cumulative operation
time reached 17,300 and 16,100 hours in April 2015, respectively. The
life of cathode was designed more than 11,000 hours. Parameters of
discharge and key structure dimensions were monitored in different
stage of life test indicated that cathodes were health enough. The test
will continue until the cathode cannot work or operation parameter is
not in normally. The result of the endurance test of cathode
demonstrated that the LaB6 hollow cathode is satisfied for the required
of thruster in life and performance.